Skip to main content Skip to search Skip to main navigation

Binder CO2 gassing module for climate chambers, control range 0 to 1 vol.%, NDIR sensor, 8012-2140

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Binder CO2 gassing module for climate chambers, control range 0 to 1 vol.%, NDIR sensor, 8012-2140"

In a closed climate chamber, plants consume CO₂ during photosynthesis, which can cause the concentration to fall below the natural ambient level of around 0.04 vol.%. The Binder CO₂ gassing module 8012-2140, on the other hand, maintains the concentration precisely between 0 and 1 vol.% and is therefore designed for plant growth applications where precise, low CO₂ control is required. It is an accessory for Binder KB PRO series cooling incubators and KBF and KBF PRO series constant climate chambers, all of which are at development stage E7.

Measurement and control

CO₂ measurement is carried out by an infrared measuring cell with an NDIR sensor (non-dispersive infrared sensor) and continuous control to a reference value. According to the manufacturer, this measurement method offers fast response times and high selectivity for CO₂; interference and ageing effects in the measurement system are largely ruled out, meaning that the system remains virtually drift-free between calibrations. The control process itself is managed entirely via the MB2 controller of the climate chamber; the gassing module cannot be operated without being connected to the climate chamber. To ensure the CO₂ concentration is displayed correctly in vol.%, the altitude of the installation site must also be entered into the controller. As this control range uses a separate CO₂ sensor to that of the 0–20 vol.% variant, the controller function ‘CO₂ measurement range 0…1 vol.%’ must also be activated to ensure the measured value is converted correctly.

Connections and interfaces

The CO₂ gassing box has a 4 to 20 mA analogue output for the CO₂ concentration, via which the measured value can be transmitted to external data acquisition systems or recording devices. The gas connection is made via a quick-release coupling on the gas cylinder, whilst the data connection to the climate chamber is via a patch cable. A CO₂ gas cylinder is not included in the scope of delivery and must be procured separately.

Combination with other accessory modules

According to the operating instructions, the CO₂ gassing module can be operated simultaneously with the LED plant light module; both accessories complement each other for comprehensive plant growth applications with controlled lighting and CO₂ concentration within the same cabinet. However, simultaneous operation with the ICH light module or the ICH-LQC light module is not possible, as both accessories occupy the same interface on the climate chamber. Anyone requiring both configurations, for example CO₂ gassing and the ICH photostability test, should plan for two separate climate chambers. For pure plant growth experiments with LED lighting and CO₂ enrichment, however, a single, suitably equipped climate chamber is sufficient.

Operation and maintenance

A fine gas filter in the gassing box can be replaced as required to ensure that measurement accuracy is maintained throughout the operational life of the unit. Two CO₂ warning stickers are included in the scope of delivery and must be affixed to a clearly visible position on the climate chamber, as special safety instructions must be observed when handling CO₂ in enclosed spaces. Before initial commissioning, the correct CO₂ outlet pressure of the gas supply and the tightness of the connections must be checked. A connection panel on the rear of the cooling incubator or climate chamber houses the data connection to the gassing box, ensuring that the cabling remains neatly organised.

Typical applications

  • CO₂ enrichment for accelerated plant growth in combination with the LED plant light module
  • Photosynthesis and growth studies with a defined, low CO₂ concentration
  • Offsetting CO₂ consumption in densely planted, enclosed climate chambers
  • Botanical and agricultural research series with reproducible climatic conditions

The CO₂ gassing box is installed on the prepared side panel of the climate chamber and connected to the main unit via a data cable, gas hose and sensor cable.

Technical details

CO₂ control range0 vol.% to 1 vol.%
Minimum concentrationAmbient value (approx. 0.04 vol.%)
Measuring principleNDIR sensor (non-dispersive infrared sensor)
Analogue output4 to 20 mA DC
Compatible series (development stage E7)KB PRO, KBF, KBF PRO
Compatible sizes260, 470, 720, 1060, 1600
Controlvia MB2 unit controller; operation not possible without a climate chamber
Power supply for gassing box24 V, via the supplied mains adaptor

Scope of delivery

  • CO₂ gassing box
  • CO₂ sensor with cable
  • 2 CO₂ warning stickers
  • 24 V mains adaptor with adaptors
  • Operating instructions
  • 2 mounting rails with screws (4 x M8, 2 x M5)
  • 2 silicone foam plugs for the slotted-hole access port
  • Patch cable for the data connection between the gassing box and the unit
  • Hose set for the gas connection

The CO₂ gas cylinder and pressure regulator are not included; these must be purchased separately.

Regulatory information

This device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, BINDER GmbH, is DE 37004983. Information on the return of old appliances can be found on our page Environment and disposal.

Individual requirements & procurement service

We provide procurement support when choosing between the CO₂ control ranges of 0 to 1 vol.% and 0 to 20 vol.%, as well as when combining the system with an LED plant lighting module or water supply systems. Details can be found on our services page.