Laboratory chairs & stools
Laboratory chairs, stools and sit-stand stools
Here you will find the seating for the laboratory: laboratory chairs with backrests, swivel stools, saddle stools and sit-stand stools with and without back support. Depending on the version, seat heights range from 450 to 850 mm, with castors for tables of standard height or with glides and a foot ring for raised workstations. The upholstery in Magic synthetic leather, Skintec or integral foam is washable. There are dedicated versions for ESD protected areas and cleanrooms, plus armrests, a foot ring and upholstery elements as accessories. With our team you can clarify which version suits your table, floor and cleaning. You can find out more about the brand on the bimos page.
Chairs by application
For laboratory workstations without special requirements, choose by seat height and chassis. If the workstation is in an ESD protected area or a cleanroom, the filters show only the suitable versions.
bimos Laboratory Saddle Chair 2 (seat height 540–800 mm, faux leather), 9473L-MG01
The bimos Laboratory Saddle Stool, also sold as a saddle chair, is designed for elevated workstations with frequently changing, short sitting phases, as found in laboratory and medical settings, particularly where mobility is required or leg room stays limited. The saddle shape aligns the pelvis and supports an upright sitting posture. 3D seating dynamics for active sitting The saddle shape allows active, dynamic sitting with variable seating positions, which bimos calls 3D seating dynamics. Seat height adjusts steplessly from 540 to 800 mm, via a release button at the front edge of the saddle seat, reachable from every sitting position. Anyone switching between a laboratory table and an elevated workbench can adjust the height directly at the workstation without tools, without getting off the stool. Synthetic leather in six colours The saddle stool is upholstered in synthetic leather, washable, easy to care for and resistant to commercially available disinfectants. Damage from sharp-edged objects cannot be ruled out. Six colours are available: black, blue, grey, light beige, mint and apricot. This covers both neutral laboratory environments and colour coding by department or work area, for example when several teams share the same room with different stools. Hygienic design and mobility The upholstery has few folds, the mechanism is enclosed, which makes it harder for germs and bacteria to settle and eases cleaning between two work steps. Load-dependent braked soft castors for hard floors come as standard, together with an extra-small aluminium star base that keeps the stool mobile without getting in the way or taking up much floor space. This combination of easy cleaning and mobility is typical of bimos laboratory and medical stool systems, where short, frequent sitting scenarios and strict hygiene requirements come together. Standard and warranty The saddle stool is built according to DIN 68877. According to the manufacturer, bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge, labour and call-out are then charged, and wear parts such as upholstery and castors are excluded from the fourth year. The conditions apply to deliveries within Germany. Typical applications Short-term workstations with frequent changes between sitting and standing Microscopy and pipetting workstations in the laboratory Medical and nursing tasks with changing sitting positions Workstations with elevated hygiene requirements Inspection and test stations in workshops and industry, where mobility between several stations matters and room for a standing leg stays limited Technical details StandardDIN 68877Seat height540 to 800 mm, steplessly via release buttonSeat width350 mmSeat depth415 mmStar base diameter540 mmMaterialSynthetic leather MagicColoursBlack, blue, grey, light beige, mint, apricotCastorsload-dependent braked soft castors for hard floorsLoad capacity120 kg (manufacturer's information)Net weight8.5 kgGross weight (shipping)10 kgShipping carton (L x W x H)634 x 534 x 277 mmCondition on deliverypartly disassembled in a cartonManufacturer's warranty3-year full warranty from delivery, then spare parts up to year 10 (labour charged) Scope of delivery bimos laboratory saddle stool in the selected colour Aluminium star base with castors Delivered partly disassembled in a carton Individual requirements and procurement service For special colours, larger quantities or spare parts such as castor sets, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
bimos NEON 1 laboratory chair, with glides, 9560-9999-278
The bimos NEON chair element is the base of the NEON system for industry and laboratory. It is delivered without seat and back upholstery, the matching upholstery element is available as a separate product. Anyone who equips several workstations with the same base model can combine one chair element with different upholstery elements, instead of buying a complete new chair for every colour. Delivered without upholstery, choose the upholstery element separately Seat and backrest arrive on the chair element without a cover. Every upholstery element from the NEON range fits the chair element, in Fabric Duotec, Synthetic leather Magic, Skintec or Supertec, each in black, blue or grey. The upholstery element is ordered separately and can later be swapped independently of the chair element. Permanent-contact backrest or synchronous mechanism The chair element is available with either a permanent-contact backrest or a synchronous mechanism. With the permanent-contact backrest, only the backrest moves when leaning back, with the synchronous mechanism, seat and backrest move in a fixed ratio to each other. Both mechanism variants share the same ergonomic package: weight regulation, seat depth adjustment, seat tilt adjustment and backrest height adjustment. Three versions for different working heights bimos offers the chair element in three versions, referred to internally by the manufacturer as NEON 1, NEON 2 and NEON 3. Low with glides or with castors covers a seat height of 450 to 620 mm, the range for workbenches and laboratory tables at standard height. High with glides and climbing aid runs from 560 to 820 mm and is intended for elevated workstations, for example at standing desks or test tables. The star base is made of aluminium, fitted with glides or castors depending on the version, and the chair is delivered partly disassembled in a carton. Anyone switching between a fixed laboratory table and an elevated workbench chooses the matching version for each workstation, without having to change the mechanism or the upholstery. Flexband as a colour accent The Flexband is the impact-resistant edging made of soft plastic and is available in blue, grey, orange or green, independent of the chosen upholstery colour. This allows workstations, shifts or departments to be distinguished by colour, without needing a different upholstery for it. Standard and castors The NEON chair element is built according to DIN 68877 and, as a bimos work swivel chair, carries the GS mark for tested safety. The castor versions come with load-dependent braked soft castors for hard floors as standard. According to the manufacturer, bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge, labour and call-out are then charged, and wear parts such as upholstery and castors are excluded from the fourth year. The conditions apply to deliveries within Germany. Matching accessory The multifunction armrest for NEON fits the chair element, adjustable in height, width and depth with a pivoting arm pad. It is not part of the standard equipment and is ordered separately. Typical applications Changing workstations in manufacturing and assembly with several users per shift Inspection and test stations with frequent sit-stand changes Laboratory workstations with requirements for wipeable surfaces Workbenches and standing desks at elevated working height Companies using colour coding by department or shift Technical details StandardDIN 68877, GS mark for tested safetyMechanismPermanent-contact backrest or synchronous mechanismErgonomic packageWeight regulation, seat depth adjustment, seat tilt adjustment, backrest height adjustmentSeat height, low (glides or castors)450 to 620 mmSeat height, high with climbing aid (glides)560 to 820 mmSeat width470 mmSeat depth420 to 480 mmBackrest height570 mmStar baseAluminium, diameter 700 mm, with glides or castors depending on versionFlexband coloursBlue, grey, orange, greenLoad capacity120 kg (manufacturer's information)Net weight18 to 21 kg, depending on versionGross weight (shipping)20 to 23 kg, depending on versionCondition on deliverypartly disassembled in a cartonManufacturer's warranty3-year full warranty from delivery, then spare parts up to year 10 (labour charged) Scope of delivery bimos NEON chair element in the selected version, mechanism and Flexband colour Aluminium star base with glides or castors, depending on version On the high version: climbing aid Delivered partly disassembled in a carton Seat and backrest upholstery and armrests are not included. The matching upholstery element and the multifunction armrest for NEON are available separately. Individual requirements and procurement service For special colours, larger quantities or spare parts, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
bimos TEXON Task Chair, low with castors, Synthetic leather Magic black, 9173-MG01
The bimos TEXON is a task chair for laboratory workstations with frequent changes of position, and for workbenches and test stations in industry. Auto-Motion technology follows every movement, the anthracite aluminium star base carries the chair as standard, and depending on the version and upholstery, the TEXON adapts to a lab bench, production line or workbench. Auto-Motion technology and Flex-Back for dynamic sitting The Auto-Motion mechanism can be locked in three positions and automatically adjusts the weight regulation, with no need to readjust the chair. The Flex-Back on the lower backrest increases the range of movement to the rear. Anyone sharing the chair between several people in shift work manages without tools and without a long adjustment time. Interchangeable upholstery and smooth surfaces Seat and backrest upholstery can be changed with one click, without tools. The seamless design and closed surfaces make cleaning straightforward, which matters at laboratory workstations with cleaning regulations and in production areas exposed to dust and splashes. Choosing upholstery to suit the application The TEXON is available in various upholstery materials, each with its own focus. The selection above shows which versions are available. Synthetic leather Magic is PVC-free, easy to clean and resistant to commercially available disinfectants, which makes it an obvious choice for laboratory workstations with hygiene requirements. Skintec combines seating comfort with easy cleaning and robustness, is likewise resistant to disinfectants, making it a second good choice for laboratories. Supertec is designed for production environments: its micro-armour is cut-resistant and non-slip while remaining breathable, which suits workbenches and manufacturing workstations in industry. Fabric Duotec is suited to clean environments, is breathable and can be cared for with commercially available upholstery cleaners. Synthetic leather Magic and Fabric Duotec are available in black and grey, Skintec additionally in off-white, and Supertec in black and grey. Four versions for different working heights The basic models differ in seat height and floor contact. Low with glides or with castors covers seat heights from 450 to 620 mm, the range for lab benches and workbenches at standard height. High with glides and foot ring or with seat-stop castors and foot ring runs from 570 to 810 mm and is intended for elevated workstations, for example on production lines or test benches at standing-desk height. At these seat heights, the foot ring gives the feet the necessary support. Anyone who needs castors at an elevated workstation chooses the version with seat-stop castors. One basic model for laboratory and industry At the lab bench, cleaning between two samples matters most, at the workbench it is the seat height relative to the machine and the stability of the castors. The TEXON covers both with the same mechanism and differs only in version and upholstery. Anyone who wants to use the chair in both the laboratory and the adjoining production area can choose version and upholstery separately for each workstation, without having to switch to a different model. Standard, safety and warranty The TEXON is built according to DIN 68877 and carries the GS mark for tested safety. The castor versions come with load-dependent braked soft castors for hard floors as standard. According to the manufacturer, bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge, labour and call-out are then charged, and wear parts such as upholstery and castors are excluded from the fourth year. The conditions apply to deliveries within Germany. Typical applications Sample preparation and microscopy workstations in the laboratory Quality assurance and test stations with frequent sit-stand changes Workbenches in production and assembly Inspection and packaging stations at elevated working height Shift work with several users on the same chair Technical details StandardDIN 68877, GS mark for tested safety Standard equipmentAuto-Motion technology, anthracite aluminium star base Seat height, low (glides or castors)450 to 620 mm Seat height, high with foot ring (glides or seat-stop castors)570 to 810 mm Seat width475 mm Seat depth460 mm Backrest height570 mm Star base diameter700 mm Load capacity150 kg (manufacturer's information)Net weight15.5 to 19.5 kg, depending on version Gross weight (shipping)18 to 22 kg, depending on version Shipping carton (L x W x H)800 x 400 x 650 mm Castorson the castor versions, load-dependent braked soft castors for hard floors Condition on deliverypartly disassembled in a carton, optionally assembled in a protective cover Manufacturer's warranty3-year full warranty from delivery, then spare parts up to year 10 (labour charged) Scope of delivery bimos TEXON task chair in the selected version, upholstery material and colour Anthracite aluminium star base On the high versions: foot ring Delivered partly disassembled in a carton 4D armrests are not included, nor is the foot ring on the low versions. Both can be ordered separately as accessories if required. Some variant product images show the chair with armrests fitted; these are not part of the scope of delivery. Individual requirements and procurement service For special colours, larger quantities or spare parts such as castor sets, armrests or foot rings, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
bimos Labsit laboratory chair, castors, plastic star base, synthetic leather, seat shell blue, 450 to 650 mm, 9123-MG01-3277
The bimos Labsit is a laboratory chair with backrest, flex function and a seat shell in five colours. It is intended for laboratories, clinics, universities and research institutions, in other words for workstations where a chair should be washable and move with the body. The upholstered surface is black and made of synthetic leather Magic or Skintec; the seat shell comes in blue, anthracite, white, orange and green. Depending on the working height, you choose the frame with castors (450 to 650 mm), with glides and foot ring (520 to 770 mm) or with seat-stop castors and foot ring (560 to 810 mm). The star base is made of black plastic or polished aluminium. Choose the laboratory chair by working height bimos calls the three frames Labsit 2, 3 and 4. They differ in seat height and undercarriage. Backrest, seat, upholstery and seat shell are the same. FrameSeat heightUndercarriageFoot ring 9123 (Labsit 2)450 to 650 mmCastorsas accessory 9121 (Labsit 3)520 to 770 mmGlidesstandard 9125 (Labsit 4)560 to 810 mmSeat-stop castorsstandard According to bimos, standard castors are not permitted above a seat height of 650 mm for safety reasons, which is why the 9123 ends there. The 9125 has seat-stop castors, which lock under load and roll when the load is removed. According to the manufacturer, they correspond to DIN 68877, including above 650 mm. The 9121 stands on plastic glides, which according to the manufacturer are intended for workstations where the chair has to provide stability. The two higher frames include a chrome-plated, height-adjustable foot ring with a wide tread surface. If you want to stay mobile at high work surfaces too, choose the 9125; if you need a firm stance, choose the 9121. Flex function in backrest and seat The backrest is made of plastic and has a 3D flex function. According to the manufacturer, it gives way when you lean back and when you turn your upper body sideways. The front edge of the seat is also flexible and yields when working in a forward-leaning posture. The backrest is 420 mm high and the seat depth is 420 mm. The seat height is adjusted steplessly by the gas spring. A handle on the backrest serves for gripping and moving the chair. bimos specifies a load capacity of 120 kg. Star base made of plastic or aluminium The star base has a diameter of 640 mm. As standard it is made of black plastic, which according to the manufacturer is light and robust. Alternatively, there is a star base made of polished aluminium, which according to the manufacturer is easy to keep clean and durable. The star base is chosen independently of frame, upholstery and seat shell colour. Upholstery and seat shell A black upholstered surface sits on the seat shell. Synthetic leather Magic is free of PVC and plasticisers, washable and, according to the manufacturer, resistant to commercially available disinfectants. According to the manufacturer, Skintec is robust, easy to care for and likewise resistant to commercially available disinfectants. According to bimos, this resistance has been tested for both upholstery materials. Extremely sharp-edged objects can damage the synthetic leather. The seat shell is available in blue, anthracite, white, orange and green. The colours differ only in appearance; dimensions and features are the same. Hygienic Design and cleaning The Labsit has a low-joint, form-fitting construction (Hygienic Design). According to the manufacturer, it can be used in laboratories of safety level S1 to S3. Which cleaning and disinfecting agents are suitable in an individual case should be clarified before use. Typical applications Laboratory workstations in chemistry, biotechnology and pharmaClinics and healthcare facilitiesUniversity and research laboratories, also for training and teaching roomsWorkstations with high work surfaces that need the 9121 or 9125 with foot ringWorkstations where the chair is regularly wiped and disinfected Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as upholstery, cover materials, castors and surfaces of star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF, German) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the Labsit laboratory chair Which frame suits which working height?The 9123 with castors adjusts from 450 to 650 mm, the 9121 with glides and foot ring from 520 to 770 mm and the 9125 with seat-stop castors and foot ring from 560 to 810 mm. The seat height is steplessly adjustable in each case. Why does the higher Labsit have seat-stop castors?According to bimos, standard castors are not permitted above a seat height of 650 mm. Seat-stop castors lock under load and, according to the manufacturer, correspond to DIN 68877. The 9125 goes up to 810 mm, which is why it has them. What is the difference between a plastic and an aluminium star base?Both have a diameter of 640 mm. According to the manufacturer, the plastic star base is light and robust, and the polished aluminium is easy to keep clean and durable. Otherwise, frame, dimensions and features are the same. How much can the Labsit carry?bimos specifies a load capacity of 120 kg. Is the Labsit available as an ESD version?The Labsit models offered here are not ESD versions. The Labsit is also available as an ESD version: bimos ESD Labsit. How long does the warranty last?bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are charged. Wear parts are excluded. Technical details Seat height9123: 450 to 650 mm, 9121: 520 to 770 mm, 9125: 560 to 810 mm Height adjustmentGas spring, stepless Undercarriage9123: castors; 9121: plastic glides and chrome-plated, height-adjustable foot ring; 9125: seat-stop castors and chrome-plated, height-adjustable foot ring BackrestPlastic, 3D flex function, height 420 mm, handle on the backrest SeatFlex function on the front edge of the seat, seat depth 420 mm Upholsteryblack, synthetic leather Magic (free of PVC and plasticisers) or Skintec Seat shellBlue, anthracite, white, orange or green Star baseBlack plastic or polished aluminium, diameter 640 mm Load capacity120 kg (manufacturer's information) Laboratory suitabilityHygienic Design (low-joint, form-fitting), safety level S1 to S3 (manufacturer's information) StandardDIN 68877, GS mark (manufacturer's information) Manufacturer's warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos Labsit laboratory chair with the selected frame, with black upholstery and seat shell in the selected colourStar base made of black plastic or polished aluminium, with gas spring9123: castors. 9121: plastic glides and chrome-plated foot ring. 9125: seat-stop castors and chrome-plated foot ringpartly disassembled in a carton, assembly according to the assembly and operating instructions Downloads Assembly and operating instructions Labsit (PDF, German)Brochure Labsit (PDF, German) Individual requirements and procurement service For accessories such as armrests, the Lab-Clip with labelling field or a foot ring for the 9123, for larger quantities or special requests, our procurement service can help.
bimos NEON Upholstery Element, Skintec grey, 9588-4002
The bimos NEON upholstery element is the seat and back cover for the NEON chair element, which is delivered without upholstery. Fits all NEON chair elements The upholstery element fits every version of the NEON chair element: low with glides (9560, 9570), low with castors (9563, 9573) and high with glides and climbing aid (9561, 9571), regardless of the chosen mechanism, permanent-contact backrest or synchronous mechanism. Anyone who already has a chair element in use and only wants to change the cover or reorder a replacement upholstery does not need a new base model for that. This is the core of the bimos modular principle: one chair element, several interchangeable upholstery covers. Four materials, three colours The upholstery element is available in four materials, each in black, blue or grey. Fabric Duotec is breathable, absorbs and releases moisture, and can be cared for with commercially available upholstery cleaners. Synthetic leather Magic is washable, easy to care for and resistant to commercially available disinfectants, though damage from sharp-edged objects cannot be ruled out. Skintec combines, according to the manufacturer, seating comfort with easy cleaning and robustness, and is likewise resistant to disinfectants. Supertec has a textile base layer with an applied micro-armour coating, is cut- and slip-resistant while remaining breathable, and is intended for production environments with higher mechanical loads. For laboratory workstations with disinfection requirements, Synthetic leather Magic or Skintec are the obvious choice, for production environments with mechanical loads Supertec tends to be preferred, and for clean office and test areas Fabric Duotec. Technical details MaterialFabric Duotec, Synthetic leather Magic, Skintec or SupertecColoursBlack, blue, greyFitsNEON chair element 9560, 9563, 9561, 9570, 9573, 9571Net weight3 kgGross weight (shipping)4 kgPackaging dimensions (L x W x H)490 x 650 x 160 mm Scope of delivery bimos NEON upholstery element in the selected material and colour Seat upholstery and back upholstery The NEON chair element is not included and is available separately. Individual requirements and procurement service For different colours or larger quantities, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
bimos ESD Labsit work chair with castors, seat height 450 to 650 mm, black Skintec, 9123E-4000-3218
The bimos ESD Labsit is a work chair with a flexible backrest for workstations in electrostatic protected areas (EPAs), in the laboratory as well as in production. According to the ESD declaration from bimos, the ESD Labsit series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs. There are three versions, which differ in seat height and floor contact: with castors, with glides and foot ring, or with seat-stop castors and foot ring. The seat is available in various ESD upholstery options. Upholstery and seat shell are black; the star base made of polished aluminium is part of the standard equipment on all versions. ESD properties according to the manufacturer’s specification bimos states a typical resistance to groundable point (Rgp) of 10⁵ to 10⁷ ohms for the ESD Labsit. The performance features give 10⁶ ohms as the typical value. According to the declaration, the chair can dissipate charges on persons to the conductive flooring or floor mat. As standard equipment, bimos lists volume-conductive plastics and conductively coated steel parts, and on the ESD Labsit 2 also conductive castors. The ESD declaration is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Flex function in the backrest and seat The backrest is made of plastic and has a 3D flex function. According to the manufacturer, it yields when leaning back and when twisting the upper body to the side. The front edge of the seat is also flexible and gives way in a forward-leaning working posture. The backrest is 420 mm high and the seat depth is 420 mm. The seat height is adjusted steplessly by the gas spring. A handle on the backrest makes it easier to move the chair. According to the manufacturer, the load capacity is 120 kg. Castors, glides or seat-stop castors The ESD Labsit 2 (9123E) has soft, load-dependent braked safety twin castors for hard floors and adjusts from 450 to 650 mm. bimos recommends castors above all for places where you have to stay flexible and mobile. The ESD Labsit 3 (9121E) ranges from 520 to 770 mm. It stands on glides made of robust, abrasion-resistant plastic and has a chrome-plated, height-adjustable foot ring. The manufacturer names glides for places where the chair has to provide support, for example for tasks requiring very high physical effort. On the ESD Labsit 4 (9125E), with 560 to 810 mm, seat-stop castors replace the glides. They lock under load and can be moved when unloaded. According to bimos, standard castors are not permitted for safety reasons above a seat height of 650 mm, whereas seat-stop castors are, and they correspond to the safety regulations of DIN 68877. For raised tables and installations where the chair stays in place, the ESD Labsit 3 is the obvious choice. Those who need to move the chair at raised workstations choose the ESD Labsit 4. ESD upholstery options The bimos price list shows all upholstery options as ESD versions. Duotec fabric is breathable, absorbs and releases moisture, and can be cleaned with commercially available upholstery cleaners. Magic synthetic leather is PVC-free, washable and unaffected by oils and, according to the manufacturer, also resistant to commercially available disinfectants. Skintec has a soft upholstery core and a robust, easy-care surface which, according to the manufacturer, is also resistant to commercially available disinfectants. According to bimos, this resistance has been tested. Supertec consists of a micro armour on a textile backing material which, according to the manufacturer, is cut-resistant, non-slip, breathable and easy to clean. Hygienic Design and cleaning The chair has a low-joint, form-fitting construction (Hygienic Design). According to the manufacturer, it can be used in laboratories of safety level S1 to S3. Which cleaning agents and disinfectants are suitable in an individual case, also with regard to the ESD property, should be clarified before use. Typical applications Workstations in electrostatic protected areas (EPAs) in electronics manufacturingAssembly, testing and inspection stations in industryLaboratory workstations with electrostatically sensitive componentsLaboratories in higher education, biotechnology, chemistry and pharmaceuticals (areas of application according to bimos)Raised tables and installations with the ESD Labsit 3 or 4Places with cleaning regulations and disinfection, for example with Magic synthetic leather or Skintec Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts, upholstery, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the ESD Labsit Is the Labsit also available without ESD?Yes. bimos also offers the Labsit as a standard version without ESD equipment. There, the seat shell is available in five colours. On the ESD Labsit, it is black. Is there proof of the ESD property?bimos issues an ESD declaration, which you can download below. It applies to the ESD Labsit series and names the typical resistance to groundable point, but neither model numbers nor values for individual upholstery options. If you need further proof for an ESD audit, please talk to us. Are there armrests or name clips?bimos names armrests (9129) and the Lab-Clip (9128) as accessories for the ESD Labsit. Neither is part of the scope of delivery. Technical details Castors (ESD Labsit 2)Glides · Foot ring (ESD Labsit 3)Seat-stop castors · Foot ring (ESD Labsit 4) Model9123E9121E9125E Seat height450 to 650 mm520 to 770 mm560 to 810 mm Height adjustmentstepless via gas spring BackrestPlastic, 3D flex function, height 420 mm, handle on the backrest SeatFlex function at the front edge of the seat, seat depth 420 mm UpholsteryDuotec fabricMagic synthetic leatherSkintecSupertec ColourUpholstery and seat shell black Star basePolished aluminium, Ø 640 mm Floor contactsoft, load-dependent braked safety twin castors for hard floorsGlides made of plasticSeat-stop castors Foot ringwithout (also available)chrome-plated, height-adjustablechrome-plated, height-adjustable Load capacity120 kg (manufacturer’s information) ESDAccording to the manufacturer’s declaration, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) Laboratory suitabilityHygienic Design (low-joint, form-fitting), safety level S1 to S3 (manufacturer’s information) StandardDIN 68877 (manufacturer’s specification) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD Labsit in the selected version, with the selected upholstery and seat shell in blackGas spring and star base made of polished aluminiumCastors on the ESD Labsit 2, glides on the ESD Labsit 3, seat-stop castors on the ESD Labsit 4Chrome-plated, height-adjustable foot ring on the ESD Labsit 3 and 4Delivery not fully assembled Armrests and Lab-Clip are not part of the scope of delivery. Downloads ESD declaration ESD Labsit, manufacturer’s declaration from bimos (PDF)Brochure Labsit and ESD Labsit (PDF)Assembly and operating instructions Labsit (PDF) Individual requirements and procurement service For armrests, the Lab-Clip, the foot ring for the ESD Labsit 2 (bimos 9478), the ESD Labsit laboratory stool, delivery assembled in a protective cover, larger quantities or special requests, our procurement service can help.
bimos ESD NEON chair element without upholstery, low with glides, permanent contact, seat height 450 to 620 mm, blue Flexband, 9560E-9999-3277
The bimos ESD NEON chair element is the frame with seat and backrest shell, mechanism and Flexband for workstations in electrostatic protected areas (EPAs). It is supplied without upholstery; the matching ESD NEON upholstery element is a separate item. According to the ESD declaration from bimos, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs. The chair element is available low with glides, low with castors and high with glides and climbing aid, each with permanent contact backrest or synchronous mechanism and with Flexband in four colours. Order chair element and upholstery element separately bimos builds the NEON from two elements: the chair element with frame and mechanism and the upholstery element for seat and backrest. According to the manufacturer, both can be configured independently and freely combined. The upholstery element is changed using the click system without tools. According to the assembly instructions, the ESD upholstery element 9588E fits all six models. Various upholstery materials are available. The selection for the upholstery element shows which versions are available. The finished chair is made up of both items; there is no complete chair as a single item. ESD properties according to the manufacturer’s specification bimos states a typical resistance to groundable point (Rgp) of 10⁵ to 10⁷ ohms for the ESD NEON. According to the declaration, the chair can dissipate charges on persons to the conductive flooring or floor mat. As standard equipment, bimos lists volume-conductive plastics and conductively coated steel parts. The ESD declaration is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Permanent contact or synchronous mechanism Models 9560E, 9563E and 9561E have the permanent contact backrest, models 9570E, 9573E and 9571E the synchronous mechanism. The remaining equipment is the same. With the permanent contact backrest, only the backrest moves when you lean back. According to bimos, it always moves with the back and supports it even when working in a forward-leaning position. The backrest angle ranges from -2° to 19°. bimos calls it a proven, somewhat simpler alternative to the synchronous mechanism and recommends it for work that is mostly forward-leaning with a short distance between workpiece and eyes, for example in the laboratory. With the synchronous mechanism, seat and backrest move together when you lean back; the angle range is from 0° to 23°. According to bimos, it is particularly suitable for frequently changing seating positions. Ergonomics package and seat shape Both mechanisms have a weight adjustment for the counter-pressure of the backrest, a seat depth, seat tilt and backrest height adjustment (see table for ranges) and a backrest that can be locked in all positions. An anti-shock safety device prevents it from snapping forward after the lock has been released. The seat surface has an integrated pelvic support and a rounded front edge. The Flexband is the impact-resistant edging made of soft plastic. Glides, castors or climbing aid The ESD NEON 1 (9560E, 9570E) stands on glides made of robust, abrasion-resistant plastic and adjusts from 450 to 620 mm. bimos recommends glides for places where the chair has to provide support, for example for tasks requiring very high physical effort. The ESD NEON 2 (9563E, 9573E) has the same height range and rolls on soft, load-dependent braked safety twin castors for hard floors such as concrete and tiles. According to bimos, castors are suitable above all where you have to stay mobile. The ESD NEON 3 (9561E, 9571E) ranges from 560 to 820 mm and stands on glides. The large-area climbing aid is height-adjustable, can be folded up through 90° and, according to bimos, moves with seat height adjustment and seat rotation. According to bimos, standard castors are not permitted for safety reasons from a seat height of 650 mm, whereas seat-stop castors are. They lock under load and roll when unloaded. For raised tables and installations, the ESD NEON 3 is the obvious choice. Tested safety according to DIN 68877 The GS mark for tested safety from TÜV Rheinland (certificate S 60170454, valid until 6 June 2028 at the latest) applies to the Neon model series with models 9560, 9570, 9563, 9573, 9561 and 9571. The suffix E in the certificate stands for the ESD version. Testing was carried out according to DIN 68877-1 and DIN 68877-2. Typical applications Workstations in electrostatic protected areas (EPAs) in electronics manufacturingAssembly, testing and inspection stations in industryLaboratory workstations with electrostatically sensitive componentsRaised tables and installations with the ESD NEON 3Places where several people of different body weights use the same chair Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts, upholstery, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the ESD NEON chair element Is the NEON also available without ESD?Yes. bimos also offers the NEON as a standard version without ESD equipment. Is there proof of the ESD property?bimos issues an ESD declaration, which you can download below. It names the ESD NEON series, but no individual item numbers. If you need further proof for an ESD audit, please talk to us. Are there armrests for the ESD NEON?Yes, bimos names 4D ESD armrests (9589E). They are adjustable in height (110 mm), width (20 mm) and depth (60 mm) and can be swivelled by ±45°. Technical details Low · Glides (ESD NEON 1)Low · Castors (ESD NEON 2)High · Glides · Climbing aid (ESD NEON 3) Model, permanent contact9560E9563E9561E Model, synchronous mechanism9570E9573E9571E Seat height450 to 620 mm450 to 620 mm560 to 820 mm Backrest anglePermanent contact: -2° to 19°, synchronous mechanism: 0° to 23° Weight adjustmentBackrest counter-pressure 50 to 120 kg Ergonomics packageSeat depth adjustment by 60 mm, seat tilt adjustment up to 9°, backrest height adjustment by 60 mm, anti-shock safety device Seat, width470 mm Seat, depth420 to 480 mm Backrest, height570 mm Star baseAluminium black, Ø 700 mm Floor contactGlides made of plasticCastors, braked depending on loadGlides made of plastic Climbing aidwithoutwithoutheight-adjustable, can be folded up through 90° Flexbandblue, grey, orange, green Upholsterynot included, upholstery element available separately Load capacity120 kg (manufacturer’s information) ESDAccording to the manufacturer’s declaration, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) StandardDIN 68877-1 and DIN 68877-2, GS mark from TÜV Rheinland (certificate S 60170454, valid until 6 June 2028 at the latest) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD NEON chair element in the selected version, mechanism and Flexband colourStar base made of aluminium in black with glides (ESD NEON 1 and 3) or castors (ESD NEON 2)Climbing aid on the ESD NEON 3Delivery not fully assembled Seat and back upholstery are not part of the scope of delivery; the ESD NEON upholstery element is available separately. The same applies to the 4D ESD armrests 9589E. Downloads ESD declaration ESD NEON, manufacturer’s declaration from bimos (PDF)Brochure NEON (PDF)Assembly and operating instructions NEON (PDF) Individual requirements and procurement service For replacement castors, seat-stop castors for the ESD NEON 3, delivery assembled in a protective cover, larger quantities or special requests, our procurement service can help.
bimos Laboratory Stool, castors, synthetic leather Magic, colour ring blue, seat height 450 to 650 mm, 9463L-MG01-3277
The bimos Laboratory Stool is a swivel stool for workstations where people often sit only briefly and cleaning is frequent, for example in the laboratory, in the clinic or in pharmaceutical production. The seat has a diameter of 400 mm and an upholstery thickness of 60 mm, and the aluminium star base measures only 540 mm. As a laboratory stool, it is available in three versions: with castors and ring release, with castors and an additional foot release, or with glides and a foot ring. The upholstery is black and made of synthetic leather Magic or Skintec. The colour ring under the seat is blue, grey, orange or green. Choose the version by working height The three versions differ in seat height, height adjustment and undercarriage. Seat, upholstery, colour ring and star base are the same on all of them. VersionSeat heightHeight adjustmentUndercarriage 9463L450 to 650 mmRing releaseCastors 9F63L480 to 650 mmFoot release and ring releaseCastors 9461L560 to 830 mmRing releaseGlides and foot ring The two castor models go up to a seat height of 650 mm. The 9461L with foot ring is intended for higher work surfaces and goes up to 830 mm. Laboratory stool with foot release: the 9F63L On the 9F63L, you set the seat height with your foot. The ring release under the upholstery is also fitted, and both adjust the gas spring steplessly. The manufacturer describes the foot release as particularly simple and hygienic. It helps when your hands are occupied or have been in contact with sample material and should not have to touch the frame as well. Compared with the 9463L, the lowest seat height is 480 mm instead of 450 mm; the highest is 650 mm on both. Castors, glides and the 650 mm limit The 9463L and the 9F63L have soft, load-dependent braked twin castors for hard floors such as concrete or tiles. The laboratory castors have a diameter of 65 mm and, according to the manufacturer, run smoothly and are easy to clean. According to bimos, standard castors are not permitted above a seat height of 650 mm for safety reasons. This is why the castor models end there. The 9461L stands on large, abrasion-resistant plastic glides. In addition, it has a chrome-plated, height-adjustable foot ring with a wide tread surface. According to the manufacturer, glides are intended for workstations where the stool has to provide stability, for example for tasks requiring a lot of force. If you prefer to roll on the 9461L, fit seat-stop castors instead of the glides. They lock under load and roll when the load is removed, and bimos also permits them above 650 mm. According to the manufacturer, they correspond to DIN 68877 and can be retrofitted. Seat, upholstery and colour ring The seat surface is round, 400 mm in size and rounded at the front. Below it is the colour ring, which protects the upholstery and adds a colour accent. You can choose from blue, grey, orange and green. The upholstery is black and 60 mm thick in both materials. Magic is a PVC-free synthetic leather which, according to the manufacturer, is particularly soft and washable, insensitive to oils and resistant to commercially available disinfectants. Extremely sharp-edged objects can damage it. According to the manufacturer, Skintec is robust, hard-wearing and easy to care for, and is likewise resistant to commercially available disinfectants. According to bimos, this resistance has been tested. If you mainly want a soft seat, choose Magic; if you need a robust upholstery, choose Skintec. Hygienic Design and cleaning The stool has a low-joint, form-fitting construction (Hygienic Design) and is designed to collect little dirt. The gas spring has a protective cover against dust and dirt. According to the manufacturer, it can be used in laboratories of safety level S1 to S3. Which cleaning and disinfecting agents are suitable in an individual case should be clarified before use. Typical applications Laboratory workstations in chemistry, biotechnology and pharma where people often sit only brieflyLaboratories at universities and higher education institutionsHealthcare facilities and medical areas where surfaces are often wiped and disinfectedWorkstations with higher work surfaces that need the 9461L with foot ringWorkstations where the height is to be adjusted without using your hands (9F63L with foot release) Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as upholstery, cover materials, castors and surfaces of star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF, German) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the Laboratory Stool What is the difference between the 9F63L and the 9463L?The 9F63L additionally has a foot release, with which the seat height can be set without using your hands. Its lowest seat height is 480 mm, that of the 9463L is 450 mm. Both have castors and go up to 650 mm. How high can the Laboratory Stool be adjusted?That depends on the version: the 9463L goes from 450 to 650 mm, the 9F63L from 480 to 650 mm and the 9461L from 560 to 830 mm. All can be adjusted steplessly by gas spring. Castors or glides?Castors are for workstations where you need to stay mobile. Glides give the stool stability. The 9461L has glides and a foot ring. Seat-stop castors as a replacement for the glides are also available. Is the upholstery resistant to disinfectants?According to the manufacturer, synthetic leather Magic and Skintec are resistant to commercially available disinfectants. Please clarify with us before use which agents are suitable in an individual case. Is the Laboratory Stool available as an ESD version?The Laboratory Stool is not an ESD version. The Laboratory Stool is also available as an ESD version: bimos ESD Hocker. How long does the warranty last?bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are charged. Wear parts are excluded. Technical details Seat height9463L: 450 to 650 mm, 9F63L: 480 to 650 mm, 9461L: 560 to 830 mm Height adjustmentGas spring with protective cover, stepless, ring release under the upholstery, on the 9F63L additionally foot release Seatround, diameter 400 mm, upholstery thickness 60 mm, rounded front edge Upholsteryblack, synthetic leather Magic (PVC-free) or Skintec Colour ringBlue, grey, orange or green Star basePolished aluminium, diameter 540 mm Undercarriage9463L and 9F63L: laboratory castors, diameter 65 mm, soft, load-dependent braked; 9461L: plastic glides and chrome-plated, height-adjustable foot ring Laboratory suitabilityHygienic Design (low-joint, form-fitting), safety level S1 to S3 (manufacturer's information) Load capacity120 kg (manufacturer's information)StandardDIN 68877, GS mark (manufacturer's information) Manufacturer's warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos Laboratory Stool in the selected version, with black upholstery and colour ringGas spring with protective cover and aluminium star base, polished9463L and 9F63L: laboratory castors. 9461L: plastic glides and chrome-plated foot ringpartly disassembled in a carton, assembly according to the assembly and operating instructions Downloads Assembly and operating instructions Laboratory Stool (PDF, German)Brochure stool system (PDF, German) Individual requirements and procurement service For accessories such as the Flex support (armrest and back support), a foot ring for the 9463L or seat-stop castors, for larger quantities or special requests, our procurement service can help.
bimos ESD Texon work chair, low with castors, seat height 450 to 620 mm, black Skintec, 9173E-4000
The bimos ESD Texon is a work chair with Auto-Motion technology for workstations in electrostatic protected areas (EPAs). According to the ESD declaration from bimos, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs. The declaration names models 9173E, 9171E and 9175E. They differ in seat height and floor contact: low with castors, high with glides and foot ring, or high with seat-stop castors and foot ring. Seat and backrest are available in various ESD upholstery options. On all versions, the star base is made of aluminium in anthracite. ESD properties according to the manufacturer’s specification bimos states a typical resistance to groundable point (Rgp) of 10⁵ to 10⁷ ohms for the ESD Texon. The performance features give 10⁶ ohms as the typical value. According to the declaration, the chair can dissipate charges on persons to the conductive flooring or floor mat. As standard equipment, bimos lists volume-conductive plastics and conductively coated steel parts. The ESD declaration is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Auto-Motion technology and Flex-Back With Auto-Motion technology, the backrest and seat surface move synchronously with the body, forwards and backwards, according to the manufacturer. The weight adjustment is automatic and the seat height is adjusted steplessly. The Flex-Back on the lower backrest gives additional flexibility in the back. The backrest can be locked in three positions. An anti-shock safety device prevents it from snapping forward unintentionally after the lock has been released. Seat and backrest The seat surface is 475 mm wide and 460 mm deep, the backrest is 570 mm high. It tapers towards the top, which, according to the manufacturer, frees up reaching space without reducing the relief for the back. The seat surface has an integrated pelvic support and a rounded front edge. The seat and back upholstery can be changed without tools using the click system. Castors, glides or seat-stop castors The ESD Texon 2 (9173E) rolls on soft, load-dependent braked safety twin castors which, according to the manufacturer, are intended for hard floors such as concrete and tiles. It adjusts from 450 to 620 mm. bimos recommends castors above all for places where you have to stay flexible and mobile. The ESD Texon 3 (9171E) stands on glides made of robust, abrasion-resistant plastic and has a chrome-plated, height-adjustable foot ring. The manufacturer names glides for places where the chair has to provide support, for example for tasks requiring very high physical effort. On the ESD Texon 4 (9175E), seat-stop castors replace the glides. They lock under load and can be moved when unloaded. According to bimos, standard castors are not permitted for safety reasons above a seat height of 650 mm, whereas seat-stop castors are, and they correspond to the safety regulations of DIN 68877. Both high versions range from 570 to 810 mm. For raised tables and installations where the chair stays in place, the ESD Texon 3 is the obvious choice. Those who need to move the chair at raised workstations choose the ESD Texon 4. ESD upholstery options The bimos price list shows all upholstery options as ESD versions. Duotec fabric is breathable, absorbs and releases moisture, and can be cleaned with commercially available upholstery cleaners. Magic synthetic leather is PVC-free, washable and unaffected by oils and, according to the manufacturer, also resistant to commercially available disinfectants. Skintec has a soft upholstery core and a robust, easy-care surface which, according to the manufacturer, is also resistant to commercially available disinfectants. Supertec consists of a micro armour which, according to the manufacturer, is cut-resistant, non-slip and breathable. Duotec fabric and Magic synthetic leather are available in black and grey, Skintec in black, grey and off-white, Supertec in black. Which cleaning agents and disinfectants are suitable in an individual case, also with regard to the ESD property, should be clarified before use. Typical applications Workstations in electrostatic protected areas (EPAs) in electronics manufacturingAssembly, testing and inspection stations in industryLaboratory workstations with electrostatically sensitive componentsRaised tables and installations with the ESD Texon 3 or 4Places with cleaning regulations and disinfection, for example with Magic synthetic leather or SkintecShift work with several users on the same chair Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts, upholstery, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the ESD Texon Is the Texon also available without ESD?Yes. bimos also offers the Texon as a standard version without ESD equipment. Is there proof of the ESD property?bimos issues an ESD declaration, which you can download below. It names the models and the typical resistance to groundable point, but no values for individual upholstery options. If you need further proof for an ESD audit, please talk to us. Are there armrests for the ESD Texon?Yes, bimos names 4D ESD armrests (9179E). They are adjustable in height (110 mm), width (20 mm) and depth (60 mm) and can be swivelled inwards and outwards by ±45°. Technical details Low · Castors (ESD Texon 2)High · Glides · Foot ring (ESD Texon 3)High · Seat-stop castors · Foot ring (ESD Texon 4) Model9173E9171E9175E Seat height450 to 620 mm570 to 810 mm570 to 810 mm Height adjustmentstepless, Auto-Motion technology with automatic weight adjustment Backrestwith Flex-Back, lockable in 3 positions, with anti-shock safety device Seat, width x depth475 x 460 mm Backrest, height570 mm UpholsteryDuotec fabricMagic synthetic leatherSkintecSupertec ColoursDuotec fabric: black, greyMagic synthetic leather: black, greySkintec: black, grey, off-whiteSupertec: black Star baseAluminium anthracite, Ø 700 mm, plastic parts black Floor contactCastors, braked depending on loadGlides made of plasticSeat-stop castors Foot ringwithoutchrome-plated, height-adjustable, Ø 500 mmchrome-plated, height-adjustable, Ø 500 mm Load capacity150 kg (manufacturer’s information) ESDAccording to the manufacturer’s declaration, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) StandardDIN 68877 (manufacturer’s specification) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD Texon in the selected version, with the selected upholstery in the selected colourStar base made of aluminium in anthracite with castors (ESD Texon 2), glides (ESD Texon 3) or seat-stop castors (ESD Texon 4)Chrome-plated, height-adjustable foot ring on the ESD Texon 3 and 4Delivery not fully assembled The 4D ESD armrests 9179E are not part of the scope of delivery; they are available separately. Downloads ESD declaration ESD Texon, manufacturer’s declaration from bimos (PDF)Brochure Texon, edition 01/25 (PDF)Assembly and operating instructions Texon (PDF) Individual requirements and procurement service For replacement castors, the foot ring for the low version (bimos 9178), delivery assembled in a protective cover, larger quantities or special requests, our procurement service can help.
bimos Fin sit-stand stool, black integral foam, seat height 620 to 850 mm, 9144-2000
The bimos Fin is a sit-stand stool for workstations where work is done standing up, for example at raised tables in the laboratory or in research. An ordinary chair does not suit the working height there, and standing for long periods is tiring. For this reason the Fin has an extra-wide comfort seat on a gas spring, which can be adjusted steplessly between 620 and 850 mm. The seat takes up part of the body weight, while the feet stay on the floor. The Fin is available with a black, blue or grey seat. Sit-stand stool instead of a chair A sit-stand stool lies between standing and sitting. On the Fin, you lean against the seat and keep working standing up. According to the manufacturer, 60 % of the body weight then rests on the seat and no longer on the legs and feet. The base column is tilted forwards by 4°. According to the manufacturer, this keeps the user in a slightly forward-leaning, active working posture. The footprint of the frame measures 525 x 335 mm and therefore remains small. Stepless seat height adjustment The seat height ranges from 620 to 850 mm, and the adjustment range is 230 mm. It is adjusted at the handle under the seat, without tools. The self-supporting safety gas spring yields slightly when you sit down and cushions the weight. If several people share a workstation, each of them readjusts the height at the handle. Comfort seat with handles and rotation The seat is made of soft SoftTouch PU foam and is extra wide. Two comfort handles are integrated into the sides of the seat surface. They help with sitting down, leaning and standing up. The Fin can also be held, pulled and carried by them. The seat rotates by 20° each to the left and to the right. According to the manufacturer, this extends the radius of action, for example when moving between the table and the apparatus. Seat surface made of integral foam Integral foam is often also called PU or polyurethane foam. According to the manufacturer, the surface is resistant, robust, washable and easy to clean, and it also withstands pointed and sharp-edged objects. The manufacturer describes the integral foam as suitable for environments with moisture, oils, greases, mild acids and alkalis, and disinfectants. Which cleaning agents and disinfectants are suitable in an individual case should be clarified before use. Frame and glides The frame is made of aluminium with a brilliant silver coating. Interchangeable glides made of felt and plastic are included in the scope of delivery and can be fitted depending on the floor type. The three seat colours black, blue and grey (basalt grey) differ only in colour. The frame, dimensions and features are the same. Typical applications Laboratory workstations with standing work, for example sample preparation, measurement series and documentationResearch and development at raised tablesWorkstations in the medical and pharmaceutical fields where the seat surface is to be wiped cleanTesting and inspection stations in productionWorkstations and installations with apparatus where work is done standing up Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as upholstery, cover materials, foam parts made of integral foam and frame surfaces. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF, German) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the Fin sit-stand stool How high can the Fin be adjusted?The seat height is steplessly adjustable from 620 to 850 mm. The handle for this is located under the seat. Does the Fin relieve the legs?According to the manufacturer, when the Fin is used, 60 % of the body weight rests on the seat instead of on the legs and feet. Can the seat surface be wiped clean?According to the manufacturer, the integral foam is washable and resistant. Please clarify with us before use which cleaning or disinfecting agents are suitable in an individual case. Is the Fin available as an ESD version?The Fin models offered here are not ESD versions. The Fin is also available as an ESD version: bimos ESD Fin. How long does the warranty last?bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are charged. Wear parts are excluded. Technical details Seat height620 to 850 mm, adjustment range 230 mm Height adjustmentstepless, self-supporting safety gas spring, handle under the seat Seatextra-wide comfort seat made of SoftTouch PU foam (integral foam), two integrated comfort handles Seat rotation20° each to the left and to the right Base columnAluminium, coated, brilliant silver, tilted forwards by 4° Frame, width x depth525 x 335 mm GlidesInterchangeable glides made of felt and plastic Seat coloursBlack, blue, grey Load capacity120 kg (manufacturer's information)StandardDIN 68877, GS mark (manufacturer's information) Manufacturer's warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos Fin sit-stand stool with comfort seat in the selected colourAluminium frame, brilliant silverInterchangeable glides made of felt and plastic DownloadsAssembly and operating instructions Fin (PDF, German)Brochure Fin (PDF, German) Individual requirements and procurement service For replacement glides, larger quantities or special requests, our procurement service can help. The Fin is also available as an ESD version: bimos ESD Fin.
bimos Flex stool with castors, black, seat height 450 to 650 mm, 9408-2000
The bimos Flex is a work stool with a gas spring for workstations where users alternate between sitting and standing, for example at laboratory benches, at test stations and in production. The seat has a slip-resistant surface and an integrated back support, and the seat height is adjusted steplessly. There are four versions: Flex 1 with castors, Flex 2 with glides, Flex 3 with glides and foot ring, and the Cleanroom Flex 3 with aluminium star base. The seat is black on all versions and made of SoftTouch PU foam. Castors, glides or foot ring The Flex 1 with castors adjusts from 450 to 650 mm. It suits workstations at normal table height where you move between several places. According to the manufacturer, the castors are soft, braked depending on load and designed for hard floors such as concrete and tiles. Flex 2 and Flex 3 have large-area glides made of abrasion-resistant plastic and range from 510 to 780 mm, which extends into the range of a standing aid. The manufacturer names glides for workstations where the chair has to provide support, for example for tasks requiring very high physical effort. The Flex 3 also has a chrome-plated, height-adjustable foot ring as a climbing aid. According to the manufacturer, it provides support when greater force is applied. For raised tables and installations, the Flex 3 is therefore the obvious choice; the Flex 2 is suitable if no foot ring is wanted. Seat, back support and rotation The seat is 360 mm wide and 380 mm deep, and 300 mm deep on the Cleanroom Flex. According to the manufacturer, the Wave surface is slip-resistant and the integrated back support supports the lumbar region. The seat can be rotated by 360°, which, according to the manufacturer, enlarges the radius of action. Gas spring and star base A self-supporting safety gas spring adjusts the seat height steplessly, over a range of 200 mm on the Flex 1 and 270 mm on the other three versions. According to the manufacturer, a cover protects the gas spring from dust and dirt. The star base is a five-legged undercarriage with flat-tapering feet, made of black plastic and 640 mm in diameter. According to the manufacturer, the flat foot ends reduce the risk of tripping. Seat made of integral foam SoftTouch PU foam is an integral foam, also called polyurethane or PU foam. According to the manufacturer, the surface is resistant, robust and washable and withstands pointed and sharp-edged objects. The manufacturer describes the integral foam as suitable for environments with oils, greases, metal chips, mild acids and alkalis, moisture or flying sparks. Which cleaning agents and disinfectants are suitable in an individual case should be clarified before use. Cleanroom Flex with aluminium star base The Cleanroom Flex corresponds to the Flex 3 in adjustment range, glides and foot ring. It differs in three points. The star base is made of polished aluminium and is 680 mm in diameter, the seat depth is 300 mm, and the upholstery is a sealed ESD integral foam in back-foamed construction. According to the manufacturer, the materials are suitable for cleanrooms, the surfaces are smooth and closed, the steel parts have a conductive coating and the comfort upholstery is conductive. According to the manufacturer, the cleanroom models are additionally sealed dust-tight. For the Cleanroom Flex, the manufacturer states air cleanliness class 3 according to DIN EN ISO 14644-1 and ESD compliance according to DIN EN 61340-5-1. Both are manufacturer’s information. Flex 1 to Flex 3 are neither cleanroom nor ESD versions. The Flex is also available as an ESD version: bimos ESD Flex. Typical applications Laboratory workstations with alternating sitting and standing workTest, inspection and assembly stations in productionWorkstations where oils, greases, metal chips or moisture occurRaised tables and installations where the Flex 2 or Flex 3 with glides is usedCleanroom and ESD areas with the Cleanroom Flex Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts made of integral foam, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF, German) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the Flex Which seat heights are available?The Flex with castors adjusts steplessly from 450 to 650 mm. The versions with glides and the Cleanroom Flex range from 510 to 780 mm. Castors or glides?Castors suit places where you move around a lot. The manufacturer names glides for workstations where the chair has to provide support. The versions from a seat height of 510 mm have glides. Can the seat surface be wiped clean?According to the manufacturer, the integral foam is washable and resistant. Please clarify with us before use which cleaning or disinfecting agents are suitable in an individual case. Is the Flex an ESD version?Only the Cleanroom Flex is ESD compliant according to the manufacturer. Flex 1 to Flex 3 in this range are not. There is a separate model, the ESD Flex with aluminium star base: bimos ESD Flex. Is there proof of the air cleanliness class of the Cleanroom Flex?Air cleanliness class 3 according to DIN EN ISO 14644-1 is manufacturer’s information. If you need proof for your cleanroom qualification, please talk to us. How long does the warranty last?bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are charged. Wear parts are excluded. Technical details Castors (Flex 1)Glides (Flex 2)Glides · foot ring (Flex 3)Cleanroom (Cleanroom Flex 3) Item number9408-20009409-20009419-20009419R-2000 Seat height450 to 650 mm510 to 780 mm510 to 780 mm510 to 780 mm Adjustment range200 mm270 mm270 mm270 mm Height adjustmentstepless, self-supporting safety gas spring with protective cover SeatSoftTouch PU foam (integral foam) black, Wave surface, integrated back support, rotatable by 360° Seat, width x depth360 x 380 mm360 x 380 mm360 x 380 mm360 x 300 mm Star baseBlack plastic, Ø 640 mmBlack plastic, Ø 640 mmBlack plastic, Ø 640 mmPolished aluminium, Ø 680 mm Floor contactCastors Ø 50 mm, braked depending on loadGlides made of plasticGlides made of plasticGlides made of plastic Foot ringnonenonechrome-plated, height-adjustablechrome-plated, height-adjustable Cleanroom and ESDno cleanroom or ESD versionAir cleanliness class 3 according to DIN EN ISO 14644-1, ESD compliant according to DIN EN 61340-5-1 (manufacturer’s information) Load capacity120 kg (manufacturer's information)StandardDIN 68877, GS mark (manufacturer’s information) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos Flex in the selected version with black seat and integrated back supportGas spring with protective cover and star base (black plastic, polished aluminium on the Cleanroom Flex)Castors on the Flex 1, glides on the Flex 2, Flex 3 and Cleanroom FlexChrome-plated, height-adjustable foot ring on the Flex 3 and Cleanroom FlexDelivery not fully assembled Downloads Assembly and operating instructions Flex 9408, 9409 and 9419 (PDF, German) Individual requirements and procurement service For replacement castors or glides, larger quantities or special requests, our procurement service can help.
bimos Cleanroom Stool with castors, synthetic leather Magic, seat height 450 to 650 mm, 9463R-MG01
The bimos Cleanroom Stool is a swivel stool with a gas spring for cleanrooms and ESD-protected areas. The ring release and the mechanism sit under a soft cover. According to the manufacturer, this is intended to prevent the release of particles from the mechanism and to avoid dust deposits. The aluminium star base is 540 mm in diameter, the seat surface is 400 mm with an upholstery thickness of 60 mm. There is a choice of three versions (castors, castors with foot release, glides with foot ring) and two black upholstery materials (synthetic leather Magic and Skintec). This results in six items. Air cleanliness class and certificate The manufacturer states air cleanliness class 3 according to DIN EN ISO 14644-1 for the Cleanroom Stool. For one model there is more: in the TESTED DEVICE certificate (no. IN 2409-1551, issued on 16 May 2025, valid for five years), Fraunhofer IPA attested for the stool system 9463R-MG01 in black that it is suitable for use in cleanrooms of air cleanliness class 2 according to ISO 14644-1. This is the castor stool with ring release and synthetic leather Magic. The basis is an examination according to ISO 14644-14; the seat surface was tested (1,200 N, 12 cycles per minute). According to its wording, the certificate applies only to this product in unchanged form. For the other five items, the manufacturer’s information (class 3) applies; the Fraunhofer certificate does not mention them. Anyone who needs a certificate from the testing institute for qualification therefore chooses the stool with castors, without foot release and with synthetic leather Magic (9463R-MG01). ESD according to DIN EN 61340-5-1 For the models 9463R, 9F63R and 9461R, bimos confirms in an ESD confirmation that they meet the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs (ESD protected areas). The typical resistance to groundable point Rgp is 105 to 107 ohm. The discharge runs to the conductive floor covering or to the floor mat. Both upholstery materials are ESD versions according to the manufacturer (synthetic leather Magic ESD and Skintec ESD). Steel parts have a conductive coating according to the manufacturer. On the versions with castors, the castors are volume-conductive. Three versions The stool with castors (9463R) adjusts from 450 to 650 mm, and the adjustment range is 200 mm. The castors have a diameter of 65 mm and are, according to the manufacturer, smooth-running and easy to clean. The height is adjusted with the circumferential handle of the ring release under the seat surface, in any seat position. The stool with castors and foot release (9F63R) ranges from 480 to 650 mm, and the adjustment range is 170 mm. In addition to the ring release, the height can be adjusted with the foot. According to the manufacturer, this works without using the hands and is particularly hygienic. Anyone who wants to adjust the height without hand contact chooses this version. The stool with glides and foot ring (9461R) ranges from 560 to 830 mm, and the adjustment range is 270 mm. According to the manufacturer, normal castors are not permitted for safety reasons above a seat height of 650 mm. For this reason, this stool has large-area glides made of abrasion-resistant plastic. The chrome-plated foot ring is height-adjustable and, according to the manufacturer, has a wide tread surface. Accessories from the manufacturer are also available: a foot ring for the stool with castors and seat-stop castors, which replace the glides on the stool with foot ring. According to the manufacturer, seat-stop castors lock under load and roll when the load is removed. Please clarify with us in advance whether the cleanroom and ESD information applies with accessories. Synthetic leather Magic or Skintec Both upholstery materials are black, 60 mm thick and, according to the manufacturer, made as sealed upholstery in back-foamed construction with a smooth, closed surface. Synthetic leather Magic is PVC-free, washable and easy to care for. According to the manufacturer, it is insensitive to oils and resistant to commercially available disinfectants. According to the manufacturer’s information, damage from extremely sharp-edged objects cannot be ruled out. Skintec has a soft upholstery core and a robust surface. According to the manufacturer, it is easy to care for and resistant to commercially available disinfectants, and the resistance has been tested according to the manufacturer’s information. Which cleaning and disinfecting agents are suitable in an individual case should be clarified before use. Typical applications Cleanrooms in production where people sit for short periodsMicroelectronics and electronics manufacturing in EPAsLaboratory areas with cleanroom or ESD requirementsWorkstations where the seat surface is regularly wiped or disinfectedQualified areas in which a certificate for the air cleanliness class is required (castor stool with synthetic leather Magic) Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as upholstery, cover materials, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF, German) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the Cleanroom Stool Which air cleanliness class does the Cleanroom Stool have?The manufacturer states class 3 according to DIN EN ISO 14644-1. For the stool with castors and synthetic leather Magic (9463R-MG01), a Fraunhofer certificate for class 2 according to ISO 14644-1 is available. For the other five items, class 3 is the manufacturer’s information. Does the Fraunhofer certificate also apply to Skintec?No, the certificate names only the stool system 9463R-MG01 with synthetic leather Magic in unchanged form. For the stool with Skintec, the manufacturer’s information (class 3) applies. Is the Cleanroom Stool ESD compliant?According to the ESD confirmation from bimos, the models 9463R, 9F63R and 9461R meet DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for EPAs. The typical resistance to groundable point is 105 to 107 ohm. Which stool suits seat heights above 650 mm?The stool with glides and foot ring (9461R) ranges from 560 to 830 mm. According to the manufacturer, castors are not permitted above a seat height of 650 mm. What does the foot release offer?The height can additionally be adjusted with the foot, without using the hands. The manufacturer calls this particularly hygienic. The ring release remains. How long does the warranty last?bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are charged. Wear parts are excluded. Technical details CastorsCastors · foot releaseGlides · foot ring Model9463R9F63R9461R Items with synthetic leather Magic9463R-MG019F63R-MG019461R-MG01 Items with Skintec9463R-40009F63R-40009461R-4000 Seat height450 to 650 mm480 to 650 mm560 to 830 mm Adjustment range200 mm170 mm270 mm Height adjustmentstepless by gas spring with protective cover, ring release under the soft coverstepless by gas spring with protective cover, foot release and ring releasestepless by gas spring with protective cover, ring release under the soft cover SeatØ 400 mm, comfort upholstery 60 mm, black, synthetic leather Magic ESD or Skintec ESD Star basePolished aluminium, Ø 540 mm Floor contactCastors Ø 65 mmCastors Ø 65 mmGlides made of plastic Foot ringnonenonechrome-plated, height-adjustable Air cleanliness classClass 3 according to DIN EN ISO 14644-1 (manufacturer’s information). For 9463R-MG01 additionally Fraunhofer IPA TESTED DEVICE, class 2 according to ISO 14644-1, no. IN 2409-1551 ESDDIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for EPAs, typical resistance to groundable point Rgp 105 to 107 ohm Load capacity120 kg (manufacturer's information)StandardDIN 68877, GS mark (manufacturer’s information) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos Cleanroom Stool in the selected version with black upholstery (synthetic leather Magic or Skintec)Gas spring with protective cover, soft cover and aluminium star base, polishedCastors on the stool with castors and on the stool with foot release, glides and chrome-plated foot ring on the stool with foot ringAccording to the manufacturer, the stool comes as an assembly in an individual carton, cleanroom models additionally sealed dust-tightDelivery not fully assembled Downloads Assembly and operating instructions stool system (PDF, German)Fraunhofer certificate Cleanroom Stool 9463R-MG01 (PDF, German)ESD confirmation Cleanroom Stool (PDF, German) Individual requirements and procurement service For accessories such as foot ring or seat-stop castors, replacement castors, larger quantities or special requests, our procurement service can help.
bimos ESD NEON upholstery element, black Skintec, 9588E-4000
The bimos ESD NEON upholstery element is the seat and back upholstery for the ESD NEON chair element, which is supplied without upholstery. The chair element is a separate item; both parts are ordered separately and assembled to form the finished chair. The upholstery element is available in various upholstery materials. The selection above shows which versions are available. Interchangeable upholstery in the click system bimos hooks the upholstery elements in and secures them with a click; no tool is needed. Each upholstery element has a small handle so that it can be removed easily. According to the assembly instructions, it fits all six models of the chair element (9560E, 9563E, 9561E, 9570E, 9573E and 9571E). When you change the upholstery, you keep the chair element. ESD properties according to the manufacturer’s specification The bimos price list shows all upholstery options as ESD versions. According to the ESD declaration from bimos, the ESD NEON series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs; the typical resistance to groundable point (Rgp) is 10⁵ to 10⁷ ohms. The declaration applies to the series and names no values for individual upholstery options. It is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Upholstery options Duotec fabric is breathable, absorbs and releases moisture, and can be cleaned with commercially available upholstery cleaners. Magic synthetic leather is PVC-free, washable and unaffected by oils and, according to the manufacturer, also resistant to commercially available disinfectants. Skintec has a soft upholstery core and a robust, easy-care surface which, according to the manufacturer, is also resistant to commercially available disinfectants. Supertec consists of a micro armour which, according to the manufacturer, is cut-resistant, non-slip and breathable. Duotec fabric is available in black, blue and grey, Magic synthetic leather, Skintec and Supertec in black. Which cleaning agents and disinfectants are suitable in an individual case, also with regard to the ESD property, should be clarified before use. Typical applications Replacement or interchangeable upholstery for ESD NEON chairs in electrostatic protected areas (EPAs)Laboratory workstations with cleaning regulations and disinfection, for example with Magic synthetic leather or SkintecWorkstations with higher mechanical stress, for example with Supertec Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts, upholstery, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Technical details ComponentUpholstery element (seat and backrest), ESD version UpholsteryDuotec fabricMagic synthetic leatherSkintecSupertec ColoursDuotec fabric: black, blue, greyMagic synthetic leather: blackSkintec: blackSupertec: black Suitable forESD NEON chair element 9560E, 9563E, 9561E, 9570E, 9573E, 9571E FasteningClick system without tools, handle on the upholstery ESDAccording to the manufacturer’s declaration, the ESD NEON series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD NEON upholstery element in the selected upholstery and colourSeat upholstery and back upholstery The ESD NEON chair element and the 4D ESD armrest 9589E are not part of the scope of delivery; both are available separately. Downloads ESD declaration ESD NEON, manufacturer’s declaration from bimos (PDF)Brochure NEON (PDF)Assembly and operating instructions NEON (PDF) Individual requirements and procurement service For larger quantities or special requests, our procurement service can help.
bimos ESD Flex stool with castors, black, seat height 450 to 650 mm, 9408E-2000
The bimos ESD Flex is a stool with a gas spring and back support for workstations in electrostatic protected areas (EPAs) where users alternate between sitting and standing. According to the ESD declaration from bimos, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs. There are three versions: Flex 1 with castors, Flex 2 with glides and Flex 3 with glides and foot ring. On all three, the seat is made of black SoftTouch PU foam and the star base of polished aluminium. ESD properties according to the manufacturer’s specification bimos states a typical resistance to groundable point (Rgp) of 10⁵ to 10⁷ ohms for the ESD Flex. The performance features give 10⁶ ohms as the typical value. According to the declaration, the chair can dissipate charges on persons to the conductive flooring or floor mat. As standard equipment, bimos lists conductively coated steel parts and conductive comfort upholstery, and on the Flex 1 also volume-conductive castors. The ESD declaration is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Castors, glides or foot ring The Flex 1 rolls on soft, load-dependent braked safety twin castors which, according to the manufacturer, are intended for hard floors such as concrete and tiles. It adjusts from 450 to 650 mm. bimos recommends castors above all for places where you have to stay flexible and mobile. The Flex 2 and Flex 3 stand on large-area floor glides made of abrasion-resistant plastic and range from 510 to 780 mm, which extends into the range of a standing aid. The manufacturer names glides for places where the chair has to provide support, for example for tasks requiring very high physical effort. The Flex 3 also has a chrome-plated, height-adjustable foot ring as a climbing aid, which, according to the manufacturer, provides support when greater force is applied. For raised tables and installations, the Flex 3 is the obvious choice. The Flex 2 is suitable if no foot ring is wanted. Seat, back support and rotation The seat surface is 360 mm wide and 380 mm deep. According to the manufacturer, the Wave surface is slip-resistant and the integrated back support supports the lumbar region. The seat can be swivelled through 360° to the left and right, which, according to the manufacturer, increases the radius of action. Gas spring, star base and load capacity The seat height is adjusted steplessly by a self-supporting safety gas spring. According to the manufacturer, a cover protects the gas spring from dust and dirt. The star base is a five-legged undercarriage with flat-tapering feet, made of polished aluminium and 640 mm in diameter. According to the manufacturer, the flat foot ends protect against the risk of tripping. According to the manufacturer, the load capacity is 120 kg. Seat surface made of integral foam SoftTouch PU foam is an integral foam, also called polyurethane or PU foam. According to the manufacturer, the surface is resistant, robust and washable and withstands pointed and sharp-edged objects. The manufacturer names integral foam for environments with oils, greases, metal chips, mild acids and alkalis or moisture. Which cleaning agents and disinfectants are suitable in an individual case, also with regard to the ESD property, should be clarified before use. Typical applications Workstations in electrostatic protected areas (EPAs) in electronics manufacturingAssembly, testing and inspection stations in industryLaboratory workstations with electrostatically sensitive componentsPlaces with alternating sitting and standing work, at raised tables with the Flex 2 or Flex 3Workstations where oils, greases, metal chips or moisture occur Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts made of integral foam, upholstery, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the ESD Flex Is the Flex also available without ESD?Yes. The standard version has a black plastic star base and is not an ESD version. Is there proof of the ESD property?bimos issues an ESD declaration, which you can download below. It names the ESD Flex series and the typical resistance to groundable point, but no individual item numbers. If you need further proof for an ESD audit, please talk to us. Can the seat surface be wiped clean?According to the manufacturer, the integral foam is washable. For care, the operating instructions refer to bimos.de/cleaning.html. Please clarify with us before use which products are suitable for your application. Technical details Castors (Flex 1)Glides (Flex 2)Glides · foot ring (Flex 3) Item number9408E-20009409E-20009419E-2000 Seat height450 to 650 mm510 to 780 mm510 to 780 mm Height adjustmentstepless, self-supporting safety gas spring with protective cover SeatSoftTouch PU foam (integral foam) ESD black, Wave surface, integrated back support, swivels through 360° Seat, width x depth360 x 380 mm Star basePolished aluminium, Ø 640 mm Floor contactCastors, braked depending on loadGlides made of plasticGlides made of plastic Foot ringwithoutwithoutchrome-plated, height-adjustable Load capacity120 kg (manufacturer’s information) ESDAccording to the manufacturer’s declaration, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) StandardDIN 68877 (manufacturer’s specification) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD Flex in the selected version with black seat and integrated back supportGas spring with protective cover and star base made of polished aluminiumCastors on the Flex 1, glides on the Flex 2 and Flex 3Chrome-plated, height-adjustable foot ring on the Flex 3Delivery not fully assembled Downloads ESD declaration ESD Flex, manufacturer’s declaration from bimos (PDF)Assembly and operating instructions Flex 9408, 9409 and 9419 (PDF) Individual requirements and procurement service For replacement castors, replacement glides, larger quantities or special requests, our procurement service can help.
bimos Multifunction Armrest for NEON Laboratory Chair, 9589-217
The bimos multifunction armrest is intended for the NEON chair element and adjusts in height, width and depth, the arm pad additionally pivots. Compatibility The armrest fits all versions of the NEON chair element: low with glides (9560, 9570), low with castors (9563, 9573) and high with glides and step-up aid (9561, 9571), regardless of mechanism and upholstery colour. It is not part of the standard equipment of the chair element and is fitted separately. Anyone sitting at the same NEON workstation for longer periods, for example at a screen or under a microscope, can relieve the shoulders and forearms with the armrest. Technical details Adjustmentheight, width and depth adjustable, arm pad pivotsFitsNEON chair element 9560, 9563, 9561, 9570, 9573, 9571Order unitpairNet weight2.5 kgGross weight (shipping)3.5 kgPackaging dimensions (L x W x H)330 x 250 x 350 mm Scope of delivery bimos multifunction armrest for NEON, 1 pair Individual requirements and procurement service For spare parts or larger quantities, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
bimos ESD Stool with castors, seat height 450 to 650 mm, black Skintec, 9463E-4000
The bimos ESD Stool is a stool with a gas spring for short periods of sitting at workstations in electrostatic protected areas (EPAs). According to the ESD declaration from bimos, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs. The declaration names models 9463E and 9461E. The ESD Stool 2 (9463E) has castors, while the ESD Stool 3 (9461E) stands on glides and has a foot ring. Both have a round seat surface 400 mm in diameter and a small aluminium star base 540 mm in diameter. The seat is available in various upholstery options, all in black. ESD properties according to the manufacturer’s specification bimos states a typical resistance to groundable point (Rgp) of 10⁵ to 10⁷ ohms for the ESD Stool. The performance features of the ESD Stool 3 give 10⁶ ohms as the typical value. According to the declaration, the stool can dissipate charges on persons to the conductive flooring or floor mat. As standard equipment, bimos lists conductively coated steel parts and conductive comfort upholstery, and on the ESD Stool 2 also volume-conductive castors. According to the brochure, all components of the stool are designed to be conductive, from the upholstery to the castor. The ESD declaration is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Castors or glides with foot ring The ESD Stool 2 rolls on soft castors for hard floors and adjusts from 450 to 650 mm. bimos recommends castors above all for places where you have to stay flexible and mobile. According to bimos, standard castors are not permitted for safety reasons above a seat height of 650 mm, which is why the castor models end there. The ESD Stool 3 ranges from 560 to 830 mm and has large-area floor glides made of abrasion-resistant plastic. The manufacturer names glides for places where the stool has to provide support, for example for tasks requiring very high physical effort. The chrome-plated foot ring is height-adjustable and, according to bimos, provides support thanks to its wide tread surface. It suits raised tables and installations. Anyone who wants to roll at a raised workstation will find ESD seat-stop castors from bimos as an accessory. They lock under load, can be moved when the load is removed and, according to the manufacturer, are also permitted above 650 mm. According to the manufacturer, they correspond to DIN 68877 and can be retrofitted. Seat and height adjustment The seat surface has a diameter of 400 mm, and the comfort upholstery is 60 mm thick. The front edge is rounded, and under the seat surface an upholstery protector protects against corners and edges. The seat height is adjusted steplessly by a gas spring, which is operated with the ring release, the circumferential handle under the seat. This is possible in any seated position. According to the manufacturer, a cover protects the gas spring from dust and dirt. According to the manufacturer, the load capacity is 120 kg. On the ESD Stool, the colour ring under the seat surface is black. ESD upholstery options The bimos price list shows all upholstery options as ESD versions. Duotec fabric is breathable and absorbs and releases moisture. It can be cleaned with commercially available upholstery cleaners. Magic synthetic leather is PVC-free, washable and unaffected by oils and, according to the manufacturer, also resistant to commercially available disinfectants. Extremely sharp-edged objects can damage it. Skintec has a soft upholstery core and a robust, easy-care surface. According to the manufacturer, Skintec is also resistant to commercially available disinfectants, and bimos states that this resistance has been tested. Supertec consists of a micro armour on a textile backing material. According to bimos, it is cut-resistant, non-slip, breathable and easy to clean; it was developed for production environments. Which cleaning agents and disinfectants are suitable in an individual case, also with regard to the ESD property, should be clarified before use. Typical applications Workstations in electrostatic protected areas (EPAs) in electronics manufacturingAssembly, testing and inspection stations in industryLaboratory workstations with electrostatically sensitive componentsRaised tables and installations with the ESD Stool 3Places with regular cleaning and disinfection, for example with Magic synthetic leather or SkintecWorkstations with short periods of sitting alternating with standing Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as foam parts, upholstery, castors and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the ESD Stool Is the stool also available without ESD?Yes. bimos also offers the stool system without ESD equipment, for example as the Allround Stool and the Laboratory Stool. Is there proof of the ESD property?bimos issues an ESD declaration, which you can download below. It names models 9463E and 9461E and the typical resistance to groundable point, but no values for individual upholstery options. If you need further proof for an ESD audit, please talk to us. Is there a back support or armrest?Yes, bimos names the ESD Flex support 9464E. It serves as armrest and back support at the same time and is height-adjustable by 100 mm. bimos describes it as ESD-compliant. Technical details Castors (ESD Stool 2)Glides · foot ring (ESD Stool 3) Model9463E9461E Seat height450 to 650 mm560 to 830 mm Height adjustmentstepless, gas spring with protective cover, ring release Seatround, Ø 400 mm, upholstery thickness 60 mm, rounded front edge, upholstery protector under the seat surface UpholsteryDuotec fabricMagic synthetic leatherSkintecSupertec Colourall upholstery black, colour ring black Star basePolished aluminium, Ø 540 mm Floor contactsoft castors for hard floorsGlides made of plastic Foot ringwithoutchrome-plated, height-adjustable Load capacity120 kg (manufacturer’s information) ESDAccording to the manufacturer’s declaration, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) Standardnot specifiedDIN 68877 (manufacturer’s specification) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD Stool in the selected version, with the selected upholstery in blackGas spring with protective cover and star base made of polished aluminiumCastors on the ESD Stool 2, glides on the ESD Stool 3Chrome-plated, height-adjustable foot ring on the ESD Stool 3Delivery not fully assembled The ESD Flex support 9464E is not part of the scope of delivery. Downloads ESD declaration ESD Stool, manufacturer’s declaration from bimos (PDF)Brochure stool system (PDF)Assembly and operating instructions stool system (PDF) Individual requirements and procurement service For replacement castors, the foot ring for the ESD Stool 2 (bimos 9478), the ESD Flex support, ESD seat-stop castors, delivery assembled in a protective cover, larger quantities or special requests, our procurement service can help.
bimos ESD Fin sit-stand stool for laboratory and ESD areas, seat height 620 to 850 mm
The bimos ESD Fin is a sit-stand stool for workstations in ESD protected areas (EPAs) where most of the work is done standing, for example at raised tables. According to the ESD declaration from bimos, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs. The extra-wide comfort seat is mounted on a gas spring and can be adjusted steplessly from 620 to 850 mm. bimos offers the ESD version with a black seat made of SoftTouch PU foam; the frame is made of aluminium in brilliant silver. ESD properties according to the manufacturer’s specification bimos states a typical resistance to groundable point (Rgp) of 10⁵ to 10⁷ ohms for the ESD Fin. The performance features give 10⁶ ohms as the typical value. According to the declaration, the sit-stand stool can dissipate charges on persons to the conductive flooring or floor mat. As standard equipment, bimos lists conductively coated steel parts and conductive comfort upholstery; bimos describes the star base as electrically conductive. The ESD declaration is a manufacturer’s declaration from bimos and not a test report from an independent test laboratory. Sit-stand stool for raised workstations On a sit-stand stool, you lean against the seat and continue working standing up. According to the manufacturer, 60 % of the body weight then rests on the seat instead of on the legs and feet. The seat height ranges from 620 to 850 mm. The manufacturer describes the adjustment range of 230 mm as extra large. The self-supporting safety gas spring adjusts the height steplessly. Comfort seat with handles and rotation The seat is extra-wide and has two integrated handles. They can also be used to carry the sit-stand stool. The seat swivels up to 20° to the left and right, which, according to the manufacturer, extends the radius of action during dynamic work, for example when changing between table and installation. Seat surface made of integral foam SoftTouch PU foam is an integral foam, also called polyurethane or PU foam. According to the manufacturer, the surface is resistant, robust and washable and withstands pointed and sharp-edged objects. The manufacturer names integral foam for environments with oils, greases, metal chips, mild acids and alkalis or moisture. Which cleaning agents and disinfectants are suitable in an individual case, also with regard to the ESD property, should be clarified before use. Frame, interchangeable glides and load capacity The base and column are made of aluminium with a brilliant silver coating. The column is tilted 4° forwards. According to the manufacturer, this keeps the user in a slightly forward-leaning, active working posture. The footprint of the frame measures 525 x 335 mm; according to the manufacturer, it is small and trip-proof. The scope of delivery includes interchangeable glides made of felt or plastic, which, according to bimos, are intended for hard and soft floors. According to the manufacturer, the load capacity is 120 kg. Typical applications Workstations in ESD protected areas (EPAs) in electronics manufacturingLaboratory workstations with electrostatically sensitive componentsAssembly, testing and inspection stations involving standing workWorkstations at raised tables and installations where a chair does not match the table heightWorkstations where oils, greases, metal chips or moisture occur Warranty bimos grants a 3-year full warranty from delivery. From the fourth to the tenth year, bimos supplies spare parts free of charge; labour and call-out are then charged. Excluded are wear parts such as cover materials, foam parts made of integral foam, upholstery and surfaces of frames and star bases. The warranty conditions apply to Germany. In the event of a warranty claim, please contact us. The bimos warranty terms (PDF) apply. Your statutory rights in respect of defects remain unaffected. Frequently asked questions about the ESD Fin Is the Fin also available without ESD?Yes. The standard version of the Fin is available with a black, blue or grey seat. It is not an ESD version. Is there proof of the ESD property?bimos issues an ESD declaration, which you can download below. It names the ESD Fin series and the typical resistance to groundable point, but no individual item numbers. The documents do not give individual values for components such as the interchangeable glides. If you need further proof for an ESD audit, please talk to us. Can the seat surface be wiped clean?According to the manufacturer, the integral foam is washable. For care, the operating instructions refer to bimos.de/cleaning.html. Please clarify with us before use which products are suitable for your application. Technical details Item number9144E-2000 Seat height620 to 850 mm, adjustment range 230 mm Height adjustmentstepless, self-supporting safety gas spring Seatextra-wide comfort seat made of SoftTouch PU foam (integral foam) ESD black, two integrated handles Seat rotationup to 20° to the left and right FrameAluminium, coated, brilliant silver, column tilted 4° forwards Frame, width x depth525 x 335 mm GlidesInterchangeable glides for hard and soft floors, made of felt or plastic Load capacity120 kg (manufacturer’s information) ESDAccording to the manufacturer’s declaration, the series meets the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021 for use in EPAs, typical resistance to groundable point Rgp 10⁵ to 10⁷ ohms (manufacturer’s specifications) StandardDIN 68877 (manufacturer’s specification) Manufacturer’s warranty3-year full warranty from delivery, then spare parts free of charge up to the 10th year, labour and call-out chargeable, wear parts excluded Scope of delivery bimos ESD Fin sit-stand stool with black comfort seatGas spring and frame made of aluminium, brilliant silverInterchangeable glides made of felt or plastic Downloads ESD declaration ESD Fin, manufacturer’s declaration from bimos (PDF)Assembly and operating instructions Fin (PDF)Brochure Fin (PDF) Individual requirements and procurement service For replacement glides, larger quantities or special requests, our procurement service can help.
bimos 4D Armrests for TEXON Task Chair, 9179
The bimos 4D armrests are intended for the TEXON task chair and adjust in height, width and depth, the arm pad additionally pivots. Compatibility The 4D armrests fit all four versions of the TEXON: low with glides, low with castors, high with glides and foot ring, and high with seat-stop castors and foot ring, regardless of upholstery material and colour. They are not included in the scope of delivery of the TEXON and are fitted separately. Anyone sitting at the same TEXON workstation for longer periods, for example at the workbench or the test table, can relieve the shoulders and forearms with the armrests. Technical details Adjustmentheight, width and depth adjustable, arm pad pivotsFitsbimos TEXON, all 4 versionsNet weight3 kgGross weight (shipping)5.5 kgPackaging dimensions (L x W x H)320 x 240 x 350 mm Scope of delivery bimos 4D armrests for TEXON Individual requirements and procurement service For spare parts or larger quantities, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
bimos Foot Ring for TEXON Task Chair, 9178
The bimos foot ring is intended for the TEXON task chair and gives the feet the necessary support at an elevated seat height, when the floor is no longer within reach. It is height-adjustable. Standard on the high versions On the high TEXON versions with seat heights from 570 to 810 mm (high with glides, high with seat-stop castors), the foot ring is part of the standard equipment. As a single part, it is suitable as a replacement. We will clarify on request, before you order, whether it can be retrofitted to the low versions. Technical details Versionheight-adjustableFitsbimos TEXONStandard onTEXON high with glides, TEXON high with seat-stop castorsNet weight3 kgGross weight (shipping)5.5 kgPackaging dimensions (L x W x H)510 x 510 x 100 mm Scope of delivery bimos foot ring for TEXON Individual requirements and procurement service For spare parts or larger quantities, our procurement service is on hand to help. It clarifies availability and lead time directly with the manufacturer.
Laboratory chair, laboratory stool or sit-stand stool: how to narrow down your choice
Anyone who sits at a laboratory table all day needs a laboratory chair with a backrest. These are the Labsit with Flex function and a seat shell in five colours, the TEXON with Auto-Motion mechanism and tool-free changeable upholstery, and the NEON, where the chair element and upholstery element are separate items. For workstations where you only sit briefly and often stand up, for example at the microscope, at the balance or between two instruments, a laboratory stool is enough. The Laboratory Stool is a swivel stool with a round seat and colour ring, and the Laboratory Saddle Stool has a saddle seat made of synthetic leather in six colours and ranges from 540 to 800 mm.
For standing workstations there are the Fin sit-stand stool with a seat height of 620 to 850 mm and the Flex sit-stand stool with back support from 450 to 780 mm. Both have a seat made of integral foam, which is washable and, according to bimos, withstands pointed and sharp-edged parts.
Seat height and chassis by table height
The table height determines the seat height and therefore the chassis. For laboratory tables of standard height, the low versions with castors are suitable, from 450 to 620 or 650 mm. According to the manufacturer, the castors are soft and braked depending on load, so they are intended for hard floors such as tiles or concrete. On the Labsit and the Laboratory Stool, standard castors are not permitted above a seat height of 650 mm, according to bimos. For raised tables and installations, the chairs therefore stand on glides with a foot ring, or they have seat-stop castors, which lock under load and roll when the load is removed. Depending on the model, the high versions go up to 830 mm. The Design filter shows for each model which combination of height and chassis is available.
Upholstery and cleaning
In the laboratory, surfaces are wiped and disinfected, so all upholstery in this category is washable. Magic synthetic leather is PVC-free and, according to bimos, soft, insensitive to oils and resistant to commercially available disinfectants. Skintec has a robust, easy-care surface and, according to the manufacturer, is also resistant to commercially available disinfectants; with synthetic leather, damage from extremely sharp-edged objects is not ruled out, according to bimos. Fin and Flex sit on integral foam, also called PU foam, which can be wiped clean. bimos states that the Labsit and the Laboratory Stool can be used in laboratories of safety classes S1 to S3. Please clarify before use which cleaning agent or disinfectant is suitable in each individual case.
ESD chairs for protected areas
If the workstation is in an ESD protected area (EPA), the chair must also dissipate charge. Labsit, TEXON, NEON, the stool, Fin and Flex are available for this as ESD versions. bimos confirms in a manufacturer’s declaration that these series meet the requirements of DIN EN 61340-5-1 and ANSI/ESD S20.20-2021, with a typical resistance to groundable point of 10⁵ to 10⁷ ohms. Discharge runs via the conductive floor covering or a floor mat. The declaration is a manufacturer’s statement and not a test report from an independent body.
Chairs for the cleanroom
Two models are designed for the cleanroom. The Cleanroom Stool has the mechanism and ring release under a soft cover and sealed upholstery, the Cleanroom Flex has a sealed ESD integral foam and, according to the manufacturer, is supplied sealed dust-tight in shrink wrap. For both, bimos specifies air cleanliness class 3 according to DIN EN ISO 14644-1 and ESD according to DIN EN 61340-5-1. A certificate from a testing institute exists for one version: the Fraunhofer IPA certifies that the Cleanroom Stool with castors and Magic synthetic leather (9463R-MG01) is suitable for Class 2, issued in May 2025 and valid for five years. You can find the cleanroom versions using the filter; for larger quantities or special requests, our procurement service helps on request.
Frequently asked questions about laboratory chairs
Which ergonomic laboratory chair is suitable for sitting for long periods?
A model with a backrest, that is Labsit, TEXON or NEON. On the Labsit the backrest moves with you (Flex function), the TEXON follows every movement with the Auto-Motion mechanism, and on the NEON you choose between permanent contact and synchronous mechanism. Armrests are available as accessories for the TEXON and NEON; they are not part of the scope of delivery.
Laboratory stool or laboratory chair with a backrest?
A laboratory stool suits workstations where you only sit briefly and often change position. Anyone who sits for longer at a stretch takes a chair with a backrest. The saddle stool is the third form, with a saddle seat made of synthetic leather and a seat height of 540 to 800 mm.
What seat height do I need at the laboratory table?
For tables of standard height, 450 to 650 mm is enough; these are the low versions with castors. For raised tables and installations there are frames with glides and a foot ring or with seat-stop castors up to 830 mm. The Laboratory Stool is available with foot release, so you set the height without touching the frame.
Can the upholstery be disinfected?
Magic synthetic leather and Skintec are, according to bimos, resistant to commercially available disinfectants, and the integral foam of Fin and Flex is washable. Please clarify before use which product is suitable in each individual case.
When do I need an ESD laboratory chair?
When the workstation is in an ESD protected area according to DIN EN 61340-5-1; your company’s ESD specification determines this. According to bimos, the ESD versions dissipate charge via the conductive floor covering or a floor mat.
Which chair is suitable for the cleanroom?
The Cleanroom Stool and the Cleanroom Flex; for both, bimos states air cleanliness class 3 according to DIN EN ISO 14644-1. Anyone who needs a certificate from a testing institute for qualification takes the Cleanroom Stool with castors and Magic synthetic leather (9463R-MG01), for which the Fraunhofer IPA certifies Class 2.
Is there a sit-stand stool for the laboratory?
Yes, the Fin with a seat height of 620 to 850 mm on glides and integral foam in black, blue or grey. Anyone who alternates between sitting and standing takes the Flex with back support. Both are also available as an ESD version.