Laboratory equipment
Laboratory Equipment brings together versatile equipment for laboratories and quality assurance: overhead stirrers, shakers and dispersers from IKA, ultrasonic baths from Bandelin, microscopes from KERN, pH electrodes from WTW and pumps from Bürkle. Specialised measuring and weighing equipment can be found under Weighing & Measurement. Our service team will be happy to help you choose the right equipment.
WTW SenTix 41 pH Electrode with Temperature Sensor, Gel Electrolyte, DIN Connector, 103635
Measuring pH in wastewater, aquariums or swimming pools should not depend on a refilling routine. The WTW SenTix 41 features a plastic shaft and a gel electrolyte which, according to WTW, is not refilled. The electrode is low-maintenance. The pH measuring range extends from 0 to 14, and it can be used at sample temperatures of 0 to 80 °C.Gel electrolyte and fibre junctionThe shaft is made of PPE/PS, is 120 mm long and has a diameter of 12 mm. The membrane is cylindrical; its resistance at 25 °C is less than 1 GΩ. According to WTW, the fibre junction prevents blockages. There is no need to monitor or top up the electrolyte level. If the electrolyte is meant to be refillable, the SenTix 51 and 52 with liquid electrolyte and a ceramic junction in a plastic shaft are the alternative.Connection and temperature measurementThe SenTix 41 has a permanently attached 1 m cable with a waterproof DIN plug (DIN 19262). An NTC temperature sensor (30 kΩ) is built in and measures the sample temperature; it is connected to the 4 mm banana plug. The gel electrodes in this range differ in plug, cable length and temperature sensor. You should therefore establish which input the measuring instrument has before placing your order.Typical applications according to WTWWhen taking samples from water bodies, at the edge of a pool or from a wastewater pipe, what counts is an electrode that is quickly ready for use. WTW names the following media for this series:Electroplating effluent, industrial wastewater and wastewater in generalAquarium and swimming pool waterGroundwater, lake water, surface water and seawaterHousehold cleanersStorage and careBefore the first measurement, remove the wetting cap; gas bubbles behind the membrane can be removed by shaking. For short measurement breaks, immerse the electrode in reference electrolyte (3 mol/l KCl, Ag+-free). Overnight and for longer periods, it stays in the wetting cap, filled with the same electrolyte. According to WTW, storing the electrode dry or in deionised water can cause permanent damage. If the cap has dried out, the electrode needs at least 24 hours in reference electrolyte. As with any pH electrode, strong acids and alkalis, hydrofluoric acid, organic solvents, oils, fats and proteins shorten its service life.Technical detailsTypepH electrode, analogue, gel electrolyteShaft materialPlastic (PPE/PS)Shaft length / Shaft diameter120 mm / 12 mmElectrolyteGel, non-refillableReference systemSilver/silver chlorideJunctionFibreMembrane shapeCylindricalpH measuring range0 to 14Temperature range0 to 80 °CMembrane resistance< 1 GΩ at 25 °CTemperature sensorNTC 30 kΩConnectionDIN plug (DIN 19262), waterproof, and 4 mm banana plugCable1 m fixed cableScope of delivery1 WTW SenTix 41 pH electrode with wetting cap1 m fixed cable with DIN and banana plugs, permanently attached to the electrodeAccessories and procurement serviceReference electrolyte KCl 3 mol/l for the wetting cap and buffer solutions for calibration are also available. Enquiries regarding other SenTix models or larger quantities go through our procurement service.
Bandelin SONOREX SUPER RK 31 Ultrasonic Bath, 0.9 L, 35 kHz, 329
Sensor tips, small cannulas, jewellery or individual cuvettes do not require a large bath for ultrasonic cleaning; rather, they need a bath that delivers uniform cavitation to every corner of the tank. With a total capacity of 0.9 l, the Bandelin SONOREX SUPER RK 31 is the smallest model in the SUPER RK series and is designed specifically for these small-item cleaning tasks in laboratories, medical practices and workshops.Small tank, noticeable cavitationAt an operating frequency of 35 kHz, the RK 31 generates a peak ultrasonic power of 160 watts at a nominal ultrasonic power of 40 watts, distributed across a single vibration system. This is sufficient for the small tank volume of 0.9 l (working capacity 0.6 l); larger SUPER RK models, such as the RK 514 BH, on the other hand, operate with four vibration systems covering a significantly larger area. The automatic SweepTec function continuously adjusts the frequency slightly, thereby preventing standing waves in the ultrasonic field; as a result, the cleaning effect remains uniform even in small volumes.Thin stainless steel tank for the laboratory benchThe oscillating tank is made of 1.4301 stainless steel with a thickness of 0.8 millimetres; the housing is made from the same material. The internal dimensions of 190 x 85 x 60 mm and the compact external dimensions of 205 x 100 x 180 mm ensure that the unit, with a net weight of 2.2 kg, can still be accommodated even on already occupied work surfaces. The RK 31 is operated via a robust rotary handle; the timer ranges from 1 to 15 minutes (tolerance ± 5 %), and continuous operation is also available.No drain, no heating, but simpleThis model has no drain; a ball valve is not provided for this size. With a capacity of 0.9 l, the tank can be emptied directly over the edge after the cleaning cycle; an additional connection would be rather cumbersome in this case. Similarly, the RK 31 does not feature a heating element. Anyone requiring heating for cleaning in the same size should choose the RK 31 H with a fixed 65 °C; the next larger model with adjustable heating is the RK 100 H.Selection guide for the SUPER RK seriesThe SUPER RK series from Bandelin covers a wide range: from the RK 31 with a 0.9-litre capacity to the RK 1050 with a total capacity of 58 l. If you are only cleaning individual small parts, sensor tips or cuvettes, you are properly equipped with the RK 31. If the batch size increases to include several instruments or small glass vessels, it is worth considering the RK 100 H (3.0 l, heated) or the RK 103 H (4.0 l, heated and with a drain). For entire sieves or beakers, the larger models from the RK 510 (9.7 l) upwards are the more suitable choice.SUPER RK, DIGITEC DT and smart ST comparedIn addition to the SUPER RK series with classic rotary knob control, Bandelin offers the DIGITEC DT series with push-button control, an LED display and DEGAS degassing, as well as the smart ST series with a touchscreen, finely adjustable power control and programme memory. Those who only clean occasionally and value straightforward, robust operation would be well advised to choose a SUPER RK model such as the RK 31. We also offer Elma Elmasonic ultrasonic baths, an alternative for laboratories already equipped with this brand.Use and maintenanceThe working capacity of 0.6 l is deliberately set below the total capacity of 0.9 l, as space must be left for the items being cleaned when filling the bath; otherwise, the liquid will spill over the rim. As for the cleaning solution itself, Bandelin offers its own TICKOPUR range of concentrates; for the SONOREX PR series of pipette cleaners, this is included in the set, whilst a suitable concentrate for the RK 31 must be purchased separately. Freshly prepared cleaning fluid contains dissolved air, which initially dampens cavitation; a short pre-run in continuous operation before the actual cleaning process dispels it. The stainless steel tank is compatible with most aqueous cleaning agents; however, abrasive sponges or chlorine-based agents should still be avoided. At the end of the working day, it is best to empty and dry the tank.Typical applicationsCleaning of small sensor tips, cannulas and needlesPrecision cleaning of jewellery and small metal partsPre-cleaning of precision mechanical components and watch movementsCleaning individual cuvettes or small sample vessels in the laboratoryFrequently asked questionsIs the SONOREX SUPER RK 31 heated?No, the RK 31 is unheated. The heated version with the same volume is the RK 31 H (fixed at 65 °C); the next larger model with adjustable heating is the RK 100 H.Does the unit have a drain?No, the RK 31 has no ball valve; with a capacity of 0.9 l, the bath is emptied directly.Is the RK 31 a medical device?Yes, it is classified as a Class I medical device according to Regulation (EU) 2017/745 and is also CE-compliant with the Low Voltage, EMC and RoHS Directives.Are the basket and lid included in the scope of delivery?No, the K 08 insert basket and the D 08 lid are available separately as accessories.Technical detailsTotal capacity / Working capacity0.9 l / 0.6 lInternal dimensions of tank (L x W x D)190 x 85 x 60 mmExternal dimensions (L x W x H)205 x 100 x 180 mmWeight (net)2.2 kgUltrasonic frequency35 kHzUltrasonic powerPeak ultrasonic power 160 W, nominal ultrasonic power 40 W, 1 vibration systemTimer1 to 15 minutes (± 5 %) or continuous operationOperationRotary knobFunctionsSweepTec, pulse functionTank materialStainless steel 1.4301, thickness 0.8 mmHousing materialStainless steel 1.4301DrainNo drain/ball valveMains connection230 V~ (± 10 %), 50/60 Hz, optionally 115 V~, 2 m fixed mains lead, protection class ICurrent consumption230 V 0.2 A / 115 V 0.4 AProtection ratingIP 32Medical device classClass I (Regulation (EU) 2017/745)ConformityLow Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EUPackaging dimensions320 x 235 x 205 mmScope of delivery1x Bandelin SONOREX SUPER RK 31 ultrasonic bathFixed mains lead (2 m)Instructions for useThe insert basket and lid are not included in the scope of delivery and are available separately.Individual requirements and procurement serviceFor the K 08 insert basket, the D 08 lid or a larger SUPER RK model, there is an individual procurement requirement. You can use our procurement service to request a quote for suitable accessories, a replacement basket or another model from the SONOREX range.
KNF LABOPORT N 96, very compact, chemical-resistant diaphragm vacuum pump with manual speed control, 322806
For those who have limited space on their lab bench but still need a reliable, chemical-resistant vacuum source, the KNF LABOPORT N 96 is a highly compact, oil-free diaphragm vacuum pump. Weighing just 1.3 kg and measuring 75 x 119 x 156 mm, it fits next to almost any workstation and can be precisely adjusted to the specific application via the manual speed control, for example for filtration, liquid aspiration or solid-phase extraction (SPE). Very compact and lightweight Measuring just 75 x 119 x 156 mm (W x H x D) and weighing 1.3 kg, the N 96 is the most compact pump in the LABOPORT range. Its small footprint makes it a practical addition to workstations where there is no room for larger vacuum pumps, such as directly next to a filtration unit or an SPE setup. Chemical-resistant materials, tailored to the design The pump head is made of PPS (polyphenylene sulphide), the diaphragm is PTFE-coated, and the valves are made of FKM. This combination of materials differs from that of the larger LABOPORT-N pumps (which feature a TFM PTFE pump head and FFPM valves), but is designed specifically for the compact design of the N 96 and its intended applications. Manual, stepless speed control The N 96’s flow rate can be continuously adjusted to suit the specific application via the manual speed control. According to the manufacturer, this ensures exceptional ease of use in day-to-day laboratory work and enables precise vacuum control, for example when gently filtering sensitive samples. Up to 2.5 bar operating pressure, not just vacuum In addition to a maximum ultimate vacuum of 130 mbar (abs.), the N 96 also achieves an operating pressure of up to 2.5 bar (rel.). This means it can be used not only for evacuation but also, where required, for pumping under slight overpressure, a difference from the larger LABOPORT-N pumps, which are primarily designed for vacuum operation. Mains-powered via an external plug-in power supply The pump itself operates at 24 V DC and is powered via an external plug-in power supply with a wide-range input (100 to 240 V AC, 50/60 Hz); it does not have a built-in battery. The power consumption is 19 W; the pump’s operating current is 0.9 A, whilst that of the power supply unit is 0.4 A (230 V AC) or 0.7 A (100 V AC). The degree of protection is IP40. Permissible media and ambient temperatures range from +5 to +40 °C. Maintenance-free and 100 % oil-free According to the manufacturer, the N 96 operates maintenance-free and is 100 % oil-free. There is no need for regular oil changes, and there is no risk of oil mist entering the gases being pumped or the laboratory air, an advantage wherever contamination-free conditions are required, such as during sample preparation for analysis. Gas connection and accessories The gas connection is a 1/8 NPT fitting; the supplied hose connector has an internal diameter of 6 mm and is made of PP. A column mounting bracket is available for wall mounting if required, along with a spare parts kit and a power supply set for replacement purposes. Suitable for confined spaces As the N 96 is powered by an external plug-in power supply, the pump housing itself remains particularly compact, an advantage wherever shelves, fume hoods or workstations are already densely occupied. The column mount also allows for space-saving installation away from the worktop, for example on a stand or a wall within easy reach of the workstation. Typical applications Filtration Liquid aspiration Solid-phase extraction (SPE) For example, the N 96 can be placed right next to an SPE cartridge stand, where it provides the necessary vacuum for sample purification in a space-saving manner, without the need for a separate, bulky pump setup. Need a higher flow rate? The larger LABOPORT series If the flow rate of 7 l/min is insufficient for a larger application, or if there is an additional need to collect liquids and condensate or to recover solvents, there are also the larger LABOPORT series: the pure diaphragm vacuum pump N 820 G / N 840 G (20 and 34 l/min respectively), the SR 820 G / SR 840 G vacuum pump system with two separator bottles, and the SH 820 G / SH 840 G vacuum pump system with a separator and high-performance condenser for solvent recovery. Technical details Flow rate (max.)7 l/min (0.4 m³/h) Ultimate vacuum (max.)130 mbar (abs.) Operating pressure (max.)2.5 bar (rel.) Pump headPPS (polyphenylene sulphide) DiaphragmPTFE-coated ValvesFKM Pump voltage24 V DC Power supply voltage100 to 240 V AC, 50/60 Hz (plug-in power supply, wide-range input) Power P119 W Operating current, pump0.9 A Operating current of power supply unit0.4 A (230 V AC) / 0.7 A (100 V AC) Degree of protectionIP40 Permissible medium/ambient temperature+5 to +40 °C Dimensions (W x H x D)75 x 119 x 156 mm Weight1.3 kg Gas connectionNPT 1/8, hose connection ID 6, PP Scope of delivery 1x KNF LABOPORT N 96 diaphragm vacuum pump External plug-in power supply (wide-range input) Silencer Hose connection ID 6, PP Individual requirements and procurement service A spare parts kit, a power supply set and a column mounting bracket for wall mounting are among the accessories available for the N 96. If you have any questions regarding suitable accessories, spare parts or individual requirements relating to your KNF LABOPORT N 96, our procurement service will be happy to assist you.
Heidolph Hei-PLATE Mix 20l Magnetic Stirrer, up to 20 Litres, without Heating, 506-54100-00
If a batch requires more volume than a standard hotplate can accommodate, but at the same time does not require a heat source directly beneath the vessel, the Hei-PLATE Mix 20 l provides exactly this combination: stirring of up to 20 l without any heating function; according to the manufacturer, even the heat from the motor is not transferred to the work surface. The chassis is identical in construction to the Hei-PLATE Mix'n'Heat Core, but without the heating module, and covers a speed range from 100 to 1,400 revolutions per minute.No heat input for heat-sensitive substancesFor substances that are sensitive to heat, any additional source of temperature poses a risk, even the waste heat from a motor. The Hei-PLATE Mix 20 l is therefore deliberately designed without a heating function, ensuring that the base remains cool. A soft-start function gently brings the speed up to the set value, ensuring that the sample does not splash at start-up and the stir bar does not veer off course.Large Kera-Disk platform for 20 lThe 145-millimetre-diameter Kera-Disk platform, made of aluminium with a ceramic coating, is chemical-resistant and scratch-resistant, and can support samples weighing up to 25 kilograms. With a power consumption of just 25 watts in normal operation, energy usage remains low for a unit with this stirring capacity; in standby mode, it drops to 1.7 watts. The external dimensions of 168 x 101 x 299 millimetres are consistent with the rest of the Hei-PLATE range, meaning the unit can be integrated into existing workstations without any modifications.Typical applicationsStirring of large-volume batches up to 20 l without heat inputProcessing of heat-labile active ingredients and dyesPreparation of larger volumes of buffers and reagents in routine laboratory workApplications where even minimal motor heat would interfere with the sampleSupplementing a Hei-PLATE workstation with a second, non-heated unitElectrical protection and environmental conditionsDegree of protection IP42 protects against foreign bodies larger than 1 mm and against obliquely falling dripping water; the sound pressure level is below 50 dB(A). The unit operates at 230 volts at 50 or 60 hertz in Europe and 115 volts in the USA, in each case via a connection with L, N and a protective earth conductor. The permissible operating range is from 5 to 31 °C at up to 80 % relative humidity; above this, the permissible humidity decreases linearly down to 40 °C.Selection guide: smaller volume or with heatingIf 5 litres of stirring volume is sufficient, the more compact Hei-Mix S is the simpler alternative. If a heating plate is required, the identically constructed chassis with a heating module, as the Hei-PLATE Mix'n'Heat Core, delivers temperatures up to 300 °C; with additional digital Pt1000 control, it is available as the Hei-PLATE Mix'n'Heat Core+.Technical detailsDimensions (W x H x D)168 x 101 x 299 mmFootprint (Kera-Disk)Ø 145 mm, aluminium, ceramic-coatedWeightapprox. 3 kgMaximum permissible load25 kgDriveEC motor, counter-clockwise rotationSpeed range100 to 1,400 rpmDegree of protection (EN 60529)IP42Sound pressure level< 50 dB(A)Rated voltage230 V, 50/60 Hz (EU); 115 V, 50/60 Hz (US)Connection typeL+N+PEProtection classIOvervoltage categoryIIPollution degree2Power consumption25 W in normal operation, 1.7 W on standbyEMC classB, Group 1Operating temperature5 to 31 °C at up to 80 % relative humidity, 32 to 40 °C at up to 50 % relative humidity (linearly decreasing)Installation altitudeup to 2,000 m above sea levelScope of deliveryHei-PLATE Mix 20 l, order number 506-54100-00The silicone cover for the Hei-PLATE Mix 20 l is not included in the scope of delivery and must be ordered separately.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Heidolph Scientific Products GmbH, is DE 50705753. Information on the return of old appliances can be found on our Environment and disposal page.Warranty and procurement serviceHeidolph Scientific Products GmbH, Schwabach, provides a 3-year manufacturer’s warranty against defects in materials and workmanship. This excludes glass and wear parts, damage caused during transport, and damage resulting from improper use. If the device is registered with Heidolph, the warranty begins on the date of purchase; otherwise, it begins on the date of manufacture as indicated by the serial number. Your statutory warranty rights remain unaffected. For this model in the Hei-PLATE series, Heidolph offers a 10-year warranty provided the instrument is registered with Heidolph within the first year of purchase. Our procurement service can, if required, source the appropriate silicone cover and other accessories for larger stirring volumes.
Bürkle stainless steel drum pump with outlet elbow, 91 cm immersion depth, for drums up to 220 l, 5601-0800
The 91-cm version of the Bürkle stainless steel drum pump with an outlet elbow delivers 540 ml per stroke. With an immersion depth suitable for drums up to approx. 220 l, it covers standard 200-litre drums. Delivery rate540 ml/stroke Max. immersion depth91 cm Outer diameter of outlet12 mm Length of outlet elbow290 mm ConnectionFor openings from 32 mm, drum screw connection For containers up toapprox. 220 l Anyone who needs to safely transfer flammable or corrosive liquids from a drum or canister requires more than just a simple hand pump. The Bürkle stainless steel drum pump is a hand-operated reciprocating piston pump, which has been developed specifically for this purpose. Thanks to its electrical conductivity and DEKRA-tested suitability for Ex zones 0, 1 and 2, it can also be used in areas where highly flammable vapours are likely to be present, such as when decanting solvents or other flammable chemicals in workshops, laboratories and production facilities. DEKRA-tested for Ex zones 0, 1 and 2 The drum pump was specially developed for use in Ex zones 0, 1 and 2 and is DEKRA-tested for explosion groups IIA and IIB. Thanks to the electrical conductivity of all parts in contact with the medium, it is suitable for highly flammable and combustible liquids. Important for safe operation: When handling flammable or highly flammable liquids, all parts of the pump must be earthed, for example using an anti-static kit. The pump is not suitable for acetone or similar dehydrating solvents. Material: 1.4301 stainless steel with PTFE seals All parts in contact with the medium are made of corrosion-resistant stainless steel 1.4301 (V2A), which, according to Bürkle, promises a long service life even in damp or aggressive environments. The PTFE seals also ensure high chemical resistance and good sliding properties during pumping, so that the pump remains smooth-running even after prolonged use. Two versions: outlet elbow or hose with tap The Bürkle stainless steel drum pump is available in two versions. The version with an outlet elbow (length 290 mm, outlet outer diameter 12 mm) is suitable for direct filling into a container placed underneath. The version with an outlet hose and tap (hose length 1.2 m, outlet outer diameter 12.8 mm) allows for metered, controlled dispensing thanks to the shut-off tap, even when the receiving vessel is not positioned directly beneath the pump. The outlet elbow and outlet hose can also be swapped, making the pump versatile for a range of filling situations. What immersion depth for which container? The pump is available in three lengths, and the immersion depth is infinitely adjustable. This makes it possible to find the suitable Bürkle stainless steel drum pump for different containers: 36 cm immersion depth: for containers up to approx. 30 l 57 cm immersion depth: for containers up to approx. 60 l 91 cm immersion depth: for containers up to approx. 220 l, such as standard drums The 91 cm version with an outlet elbow covers standard 200-litre drums with its immersion depth. Flow rate and viscosity Depending on the selected immersion depth, the pump delivers between 190 and 540 ml per stroke, which corresponds to a flow rate of 9 to 22 l/min across the entire range. The immersion tube has a consistent diameter of 32 mm, and the pump handles fluids with a viscosity of up to 500 mPa·s. Robust construction, versatile use Stainless steel drum pumps are versatile and suitable for a wide variety of drums, containers and other vessels. The robust construction from high-quality, corrosion-resistant 1.4301 stainless steel ensures, according to Bürkle, a long service life, particularly in damp or corrosive environments. Typical applications Decanting flammable or corrosive liquids and chemicals from drums, canisters and other containers Use in workshops, laboratories and production facilities Filling in Ex zones 0, 1 and 2, provided the pump is earthed in accordance with regulations Choice of immersion depth to suit the container size, from small 30-litre canisters up to 220-litre drums Handling and cleaning To operate, screw on the outlet elbow or hose, insert the pump with the drum screw connection into the drum opening and screw it in hand-tight. After removing the cap, the liquid can be pumped out using the handle on the piston rod. During the final pumping stroke, push the piston rod in as far as it will go before carefully unscrewing the pump from the drum. After use, the drum pump should be rinsed with a pH-neutral liquid. Technical details Product principleManually operated reciprocating piston pump Material of parts in contact with the mediumStainless steel 1.4301 (V2A) Seal materialPTFE Immersion tube diameter32 mm Viscosityup to 500 mPa·s Flow rate (entire range)9 to 22 l/min Immersion depthcontinuously adjustable, max. 91 cm Drive typeManually operated ColourSilver Ex zone0, 1, 2 Explosion groupsIIA, IIB Explosion protection testingDEKRA-tested Electrical conductivityYes Outlet elbow/hoseReplaceable Scope of delivery 1x Bürkle stainless steel drum pump in the selected version (with outlet elbow or with hose and tap) and immersion depth Operating instructions Not included in the scope of delivery: drum screw connection and the anti-static earthing kit required for use with flammable liquids. Individual requirements and procurement service For the mandatory earthing required when transferring flammable liquids, Bürkle offers a suitable anti-static kit (5602-1000), as well as a drum mount (5618-0200) for storing the pump in an upright position between uses. We are happy to source both on request: if you have any questions regarding suitable accessories, spare parts or specific requirements relating to your drum pump, our procurement service will be happy to assist you.
Kern OZL-46 stereo zoom microscopes, zoom 0.7x to 4.5x, LED incident and transmitted light, binocular and trinocular
The Kern OZL-46 series comprises six stereo zoom microscopes with LED incident light and LED transmitted light for assembly and repair workstations, training workshops and testing centres. The zoom range is continuously adjustable from 0.7x to 4.5x; when used with the HWF 10x eyepieces, this provides a total magnification of 7x to 45x. Three models are binocular (OZL 463, OZL 465, OZL 467), and three are trinocular with a third port for a camera (OZL 464, OZL 466, OZL 468). All models have a built-in power supply.Which modelThe binocular models OZL 463, OZL 465 and OZL 467 do not have a camera output. The OZL 463 and OZL 465 are mounted on a column stand; according to the data sheet, they differ in net weight (4.2 kg versus 4.6 kg). According to the data sheet, the OZL 467 has a mechanical stand. Of the trinocular models, the OZL 464 and OZL 466 have a beam splitter ratio of 50:50, meaning that the eyepieces and camera can be used simultaneously. Both are mounted on a column stand and feature a click-stop on the zoom wheel. For the OZL 468, the beam splitter ratio is 0:100 according to the data sheet, and the stand is mechanical, as stated in the data sheet. If you need to document and observe live through the eyepiece at the same time, choose the OZL 464 or the OZL 466. Those who work exclusively at the eyepiece will find the OZL 463, the OZL 465 or the OZL 467 sufficient.Zoom, field of view and click-stopAccording to the data sheet, the zoom wheel on the OZL 464 and OZL 466 has an integrated click-stop. It clicks into defined magnification steps so that a setting, once selected, can be found again reproducibly. The data sheet does not specify a click-stop for the other models. The zoom ratio is 6.4:1. The field of view measures 4.4 to 28.6 mm, the working distance is 105 mm, and the maximum specimen height is 140 mm. The Greenough system provides a stereoscopic image. The tube is inclined at 45° and rotates through 360°; the interpupillary distance ranges from 55 to 75 mm, and the dioptre adjustment operates on both sides from -5 to +5. The HWF 10x eyepieces have a 20 mm field of view, a high eye point and a 30 mm mounting diameter, and are fixed in the tube.Illumination and camera connectionThe incident and transmitted light sources are 3 W LEDs, each of which can be dimmed independently. The contrast method is bright field. A C-Mount adapter is required to connect a camera. Kern lists the microscope camera adapters OZB-A4809 (1x), OZB-A4810 (0.3x) and OZB-A4811 (0.5x), as well as the eyepiece camera adapter OZB-A4863 (1x). For models with a camera output, Kern lists the ODC 241, ODC 825, ODC 832 and ODC 852 cameras. For the OZL 464 and OZL 468, the ODC 854 is added; for the OZL 468, so is the ODC 251.Stand, power and dimensionsAccording to the brochure, the stand allows the microscope head to be removed and fitted into other modular systems, such as a universal stand. The coarse focus mechanism features torque control. The power supply is built-in and operates at 100 to 240 V; it is connected via a power cable. The microscopes measure 300 x 240 x 420 mm. The OZL 463 and OZL 464 have a net weight of approx. 4.2 kg, while the OZL 465, OZL 466, OZL 467 and OZL 468 weigh approximately 4.6 kg.Typical applicationsAssembly and repair workstations, for example in the electronics industryTraining organisations, schools and training workshopsTest centres and quality control: circuit boards and componentsZoology and botany, tissue preparation, dissectionSoldering work and inspection using a camera (OZL 464 and OZL 466)Models at a glanceModelTubeBeam splitter ratioStandClick-StopNet weightOZL 463Binocularnot applicableColumnnoapprox. 4.2 kgOZL 464Trinocular50:50Columnyesapprox. 4.2 kgOZL 465Binocularnot applicableColumnnoapprox. 4.6 kgOZL 466Trinocular50:50Columnyesapprox. 4.6 kgOZL 467Binocularnot applicablemechanicalnoapprox. 4.6 kgOZL 468Trinocular0:100mechanicalnoapprox. 4.6 kgTechnical detailsThese values apply to all models. Any differing values are listed in the model table.Optical systemGreenough, bright fieldTubeInclined at 45°, rotatable through 360°, interpupillary distance 55 to 75 mm, dioptre adjustment on both sides from -5 to +5EyepieceHWF 10x, field of view 20 mm, mounting diameter 30 mm, high eye point, fixedZoom0.7x to 4.5x continuously variable, ratio 6.4:1Click-StopOZL 464 and OZL 466Total magnification7x to 45xField of view4.4 mm to 28.6 mmWorking distance105 mmMaximum sample height140 mmFocusingCoarse focus, torque controlIllumination3 W LED incident light and 3 W LED transmitted light, independently dimmablePower supplyBuilt-in power supply, 100 to 240 V, power cableMains plugEuro plug included in the scope of delivery; UK and CH adapters optional, for OZL 463, 465, 467 and 468 also AUS and USDimensions (W x D x H)300 x 240 x 420 mmStorage temperature-5 °C to 40 °CLabellingCEWarranty (manufacturer)36 months according to Kern, excluding wear partsScope of deliveryOZL 463, OZL 464, OZL 465, OZL 466, OZL 467 or OZL 468 stereo zoom microscope, depending on the modelHWF 10x eyepiecesIEC power cable with Euro plugDust coverEyecupsMultilingual operating instructionsWarrantyAccording to Kern & Sohn, these microscopes come with a 3-year warranty. Kern grants 3 years on products with a list price of €500 or more and 2 years on products below that and on components; wear parts such as batteries and rechargeable batteries are excluded. Warranty repairs are carried out by Kern or by a Kern dealer.DownloadsOperating instructions Kern OZL 463, 464, 465, 466, 467 (PDF)Operating instructions Kern OZL 468 (PDF)Regulatory informationAs electrical devices, the microscopes fall under the ElektroG. The manufacturer Kern & Sohn GmbH is registered under the WEEE registration number DE 80821200. How to return old appliances is described on the page Environment and disposal.Individual requirements and procurement serviceThe following accessories are also available:Eyepieces: OZB-A4632 (HWF 15x), OZB-A4633 (HWF 20x), OZB-A4634 (HWF 25x), OZB-A4635 (HWF 10x with 0.1 mm scale)Attachment lenses: OZB-A4641 (0.5x), OZB-A4644 (0.75x), OZB-A4642 (1.5x), OZB-A4643 (2x). According to the brochure for the OZL 463, OZL 464, OZL 467 and OZL 468; for the OZL 466 only the OZB-A4642, for the OZL 465 none.Further microscope accessories: solder protection lens OZB-A4646, stand insert OZB-A4670, dust cover OBB-A1387Eyepiece cameras: ODC 874, ODC 881Cleaning: cleaning spray OCS-A1101, cleaning kit OCS 901Power cables: 822-903 (UK), MLB-A07 (Euro), YKK-01 (CH)Ready-to-use sets with a camera: OZL 464C825, OZL 464C832, OZL 464T241, OZL 466C825, OZL 466C832, OZL 466T241, OZL 468C825, OZL 468C832, OZL 468T241Enquiries are handled via our procurement service.
Heidolph Hei-PLATE Sensor Basic Package Core+ Magnetic Stirrer Set, Ø145 mm, with Pt1000 Probe, 506-21150-00
A digital display on the hotplate and an external temperature probe in the vessel are, for many laboratories, the first step towards traceable temperature control. The Sensor Basic Package Core+ combines the Hei-PLATE Mix'n'Heat Core+ digital magnetic stirrer, with a footprint of 145 millimetres, with an external Pt1000 temperature probe, whilst remaining a basic configuration without a mounting bracket or silicone cover.LCD display and two heating modesThe Hei-PLATE Mix'n'Heat Core+ included in the pack displays speed and temperature on an LCD screen; the dynamic control knobs respond to the speed of hand movement, slow for fine adjustment, fast for larger increments. There are two heating modes to choose from: FAST for rapid heating and PRECISE for control without overshoot. The included Pt1000 temperature probe (V4A, order number 509-67910-00) measures the temperature directly within the medium rather than just on the heating plate, with an accuracy of ±0.2 Kelvin plus the tolerance of the Pt1000 sensor and a resolution of 1 Kelvin. In conjunction with the probe, the magnetic stirrer covers a display and measurement range from 15 to 325 °C.Why the temperature in the medium mattersWithout an external probe, a heating plate only controls the temperature of its own surface, not that of the liquid in the vessel. For buffers, solutions or reaction mixtures with a defined target temperature, this makes a difference, particularly when the volume or shape of the vessel changes. The Pt1000 probe is immersed in the medium and provides the control system with the actual value. This allows the set temperature to be reproduced independently of the vessel.Typical applicationsBuffer and solution preparations with a fixed target temperature in the vesselReaction mixtures where the temperature is to be monitored directly inside the flaskFirst steps towards documented temperature control without additional accessoriesUpgrading an existing Core+ magnetic stirrer with an external sensorSelection guide: Basic or AdvancedIf you wish to secure the sensor permanently and protect the work surface between uses, you’ll find the right equipment in the Sensor Advanced Package Core+, which includes an additional mount and silicone cover. For reflux set-ups with a condenser, there are the dedicated Core+ and Core+ Mini reflux packages. If you do not require an LCD display and are happy with the simpler rotary knob operation, the Sensor Advanced Package Core offers the analogue alternative.Technical detailsDimensions (W x H x D)168 x 101 x 299 mmHeating plate footprintØ 145 mmWeightapprox. 3 kgMaximum permissible load25 kgDriveEC motor, counter-clockwise rotationSpeed range100 to 1,400 rpmHeating power800 W at 230 V (EU), 600 W at 115 V (US)Heating temperature range20 to 300 °CHeating controlPIDDisplayLCD displayTemperature measurement accuracy±0.2 K plus Pt1000 toleranceTemperature measurement resolution1 KDisplay and measurement range with Pt100015 to 325 °CDegree of protection (EN 60529)IP42Sound pressure levelless than 50 dB(A)Rated voltage230 V, 50/60 Hz (EU), 115 V, 50/60 Hz (US)Power consumptionNormal operation 825 W (EU) / 625 W (US), standby 1.7 WScope of deliveryHei-PLATE Mix'n'Heat Core+ magnetic stirrer, 145 mm base area, order number 506-21100-00Pt1000 temperature sensor (V4A), order number 509-67910-00The mounting bracket and silicone cover are not included with this order number; they are part of the more comprehensive Sensor Advanced package.Regulatory informationThe devices in this package are electrical appliances within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Heidolph Scientific Products GmbH, is DE 50705753. Information on the return of old appliances can be found on our Environment and disposal page.Warranty and procurement serviceHeidolph Scientific Products GmbH, Schwabach, provides a 3-year manufacturer’s warranty against defects in materials and workmanship. This excludes glass parts and wear parts, damage caused during transport, and damage resulting from improper use. If the appliance is registered with Heidolph, the warranty commences on the date of purchase; otherwise, it commences on the date of manufacture as indicated by the serial number. Your statutory warranty rights remain unaffected. Heidolph offers a 10-year warranty on the Hei-PLATE series magnetic stirrer included in the pack, provided the instrument is registered with Heidolph within the first year of purchase. This extended warranty does not apply to the temperature probe, which is sold as an accessory. Our procurement service can supply a mounting bracket, silicone cover or other accessories for the Core+ magnetic stirrer as required.
IKA T 18 mini digital Solution Disperser Set, brushless motor including tool and stand, 0010015137
Not every laboratory workstation has room for a large drive, and not every sample requires 500 watts of power. The IKA T 18 mini digital Solution (0010015137) is designed precisely for these situations: a compact, brushless disperser set with tool and stand that can be accommodated even in small spaces and is designed for samples with lower viscosity. Compact brushless drive With external dimensions of 66 x 186 x 100 millimetres and a weight of 1.8 kilograms, the drive unit is significantly smaller than the classic T 18 digital. The brushless DC motor delivers 210 watts of input power and 160 watts of output power, and is designed for a maximum viscosity of 2,000 mPas. As with the larger series, the speed range extends from 3,000 to 25,000 revolutions per minute, albeit with a slightly higher deviation of 3 %. Digital display, timer and USB-C The LED display shows the set speed, whilst an integrated timer with its own LED display manages the process time, meaning that runs do not need to be stopped manually. The device can be connected to a documentation system via the USB-C interface. In standby mode, power consumption is just 3 watts, whilst the maximum power consumption of the unit is 250 watts. Power is supplied internally via 48 volts DC at a current draw of 4,500 milliamps; the power supply unit itself covers the range from 100 to 240 volts and can therefore be used worldwide without the need for a separate voltage converter. Designed for smaller volumes and lower viscosity According to the manufacturer, the T 18 mini digital Solution is suitable for simple applications involving the homogenisation of low-viscosity samples. As with the larger model, the processable volume ranges from 0.001 to 1.5 litres; however, the maximum viscosity of 2,000 mPas is lower than that of the T 18 digital, which is 5,000 mPas. For routine samples in life sciences laboratories, training centres or smaller-scale quality control procedures that do not involve particularly tough or high-volume batches, the performance is generally adequate. What the compact design means in everyday use With a footprint that is significantly smaller than that of the classic T 18 digital, the T 18 mini digital Solution can be accommodated even where several workstations are positioned close together, such as in practical training rooms or at smaller fume hood workstations. The lower weight of 1.8 kilograms also makes manual operation more comfortable over longer periods when a stand is not used. Those who regularly switch between several workstations also benefit from the fact that the compact unit is easier to transport than the larger series. Typical applications Homogenisation of low-viscosity samples (according to the manufacturer) Smaller batches in life sciences and teaching laboratories Workstations with limited floor space Processes with documented time control via the integrated timer Brief overview within the T-18 range For those requiring higher viscosity or greater motor power, the larger T 18 digital Solution offers the suitable set with a power consumption of 500 watts instead of 210 watts. The drive unit on its own is available as the T 18 digital ULTRA-TURRAX; the dispersing tool included in the set is also available separately as the S 18 N - 19 G dispersing tool. Technical details Motor power consumption210 WMotor output160 WProcessing volume (H₂O)0.001 to 1.5 lMax. viscosity2,000 mPasSpeed range3,000 to 25,000 rpm, continuously variableSpeed deviation3 %Speed displayLEDMotor typeBrushless (direct current)Noise level without tools75 dB(A)Boom diameter13 mmBoom length160 mmProcess typeBatchTimerYes, LED displayPermissible duty cycle100 %Permissible ambient temperature range5 to 40 °CPermissible relative humidity80 %USB interfaceUSB-CMaximum power consumption250 WStandby power consumption3 WDC voltage48 V=Current consumption4,500 mADimensions (W x H x D)66 x 186 x 100 mm (drive unit)Weight1.8 kg (drive unit, excluding stand and tools)Connected load100 to 240 V, 50/60 Hz, 210 W (max. 250 W)Degree of protectionIP 30 (DIN EN 60529) Scope of delivery 1 x IKA T 18 mini digital ULTRA-TURRAX (drive unit) 1 x S 18 N - 19 G dispersing tool 1 x R 1826 plate stand 1 x R 182 boss head Differences from the neighbouring series If you only require the drive unit without the set, it is available as the T 18 mini digital ULTRA-TURRAX. An overview of all our dispersing units can be found in the ‘Dispersing Units’ category; suitable tools are listed under ‘Dispersing Tools’. Application, installation and maintenance With an IP 30 protection rating, the drive unit is slightly better protected against the ingress of foreign objects than the classic T 18 digital with IP 20; however, it is still not designed to withstand splashing water. Operation is permitted at an ambient temperature of 5 to 40 °C and a relative humidity of up to 80 %. The tool’s supplied PTFE bearing must not run dry; the medium provides both lubrication and cooling. The integrated timer reduces the effort required for manual time control in recurring processes, but does not replace the need to monitor the batch. At the end of its service life, as an electrical appliance, the drive must not be disposed of with household waste, but must be placed in the separate collection for waste electrical and electronic equipment. When the mini drive is a worthwhile investment If the viscosity of the samples is up to a maximum of 2,000 mPas and the focus is on a compact design, a timer and documentation via USB-C, the T 18 mini digital Solution reliably meets these requirements. If, on the other hand, tougher media up to 5,000 mPas are regularly processed, or if the higher power consumption of 500 watts is required, the larger T 18 digital Solution is the more suitable choice. Both sets share the same standard tool, the S 18 N - 19 G, so switching between the two sizes does not necessarily change the choice of tool. For laboratories that need to meet both requirements simultaneously, for example a sensitive batch with low viscosity followed by a tougher sample, it may also be worthwhile to purchase both sizes for different workstations. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service Those who also work with disposable dispersing tools will find the S 18/25-ET50 disposable tube from us to be a practical cleaning aid. Do you also require an additional stand for a second workstation or assistance with the USB connection to your documentation system? Through our procurement service, we support you with procurement and configuration. Frequently Asked Questions For which samples is the T 18 mini digital Solution suitable?According to the manufacturer, it is suitable for simple applications involving the homogenisation of low-viscosity samples, up to a maximum of 2,000 mPas. How does it differ from the larger T 18 digital Solution?The mini drive is brushless with a power consumption of 210 watts instead of 500 watts; it is more compact and designed for a lower maximum viscosity, but features a timer and a USB-C interface. Is a stand included in the scope of delivery?Yes, the set includes an R 1826 plate stand with an R 182 boss head. What is the USB-C interface used for?The USB-C port allows the device to be connected to a documentation system to record process data. What is the drive’s protection rating?IP 30 in accordance with DIN EN 60529, which protects against the ingress of foreign objects larger than 2.5 millimetres, but not against splashing water. Can I operate the drive worldwide without a voltage converter?Yes, the mains adaptor covers a range of 100 to 240 volts at 50/60 hertz.
WTW Standard (DIN/NIST) buffer solution PL 7, pH 6.865/6.87, PTB/NIST-traceable calibration solution according to DIN 19266-01:2000, ± 0.02 pH, 250 ml, 109120
An electrode that is incorrectly calibrated in the neutral range will introduce a bias into every subsequent measurement, particularly where pH 7, as the zero point of the scale, plays a key role. The WTW Standard (DIN/NIST) buffer solution PL 7 provides a traceable reference for this purpose: a working reference buffer solution according to DIN 19266-01:2000, traceable to PTB/NIST, with an accuracy of ± 0.02 pH at 25 °C. Together with PL 4 and PL 9, it forms the midpoint of a complete, documentable three-point calibration. Standard (DIN/NIST) buffer solution PL 7: higher accuracy class than the technical range The key difference from the ‘technical’ WTW buffer solution range lies in the accuracy class and traceability. The WTW technical buffer solution pH 7 is designed for daily routine calibration and reliably covers everyday laboratory work. The Standard (DIN/NIST) buffer solution PL 7 goes one step further: As a working reference buffer solution according to DIN 19266-01:2000, it is PTB/NIST-traceable and specified to ± 0.02 pH at 25 °C. This makes it a suitable choice wherever the calibration itself must be documented and traceable, such as in ISO/IEC 17025-accredited testing laboratories, in pharmaceutical analysis or in metrologically demanding research. Buffer system comprising two phosphate salts PL 7 is based on a mixture of disodium hydrogen phosphate and potassium dihydrogen phosphate as a buffer system and achieves a pH value of 6.87 at 20 °C, stated on the label as pH 6.865 according to DIN or pH 6.87 according to NIST. The density is 1.01 g/cm³, the melting point is -0.3 °C and the boiling point is 100 °C. Under the CLP Regulation, the solution is not classified as a hazardous substance and is not a dangerous good, which simplifies storage, transport and handling in day-to-day laboratory work. Each bottle bears its own batch code with an expiry date, ensuring that the batch used can always be identified and remains clearly traceable within the documentation of a quality management system. Traceability as part of quality assurance Traceability means that the printed pH value can be traced back through an unbroken chain of reference measurements to the national metrology institutes PTB and NIST. For a testing laboratory accredited to ISO/IEC 17025, this is precisely the difference between a plausible and a robust measurement: not only the electrode itself, but also the reference used to calibrate it, must be documented and traceable. The zero point at pH 7, in particular, affects the entire calibration curve, which is why a traceable buffer is especially important at this point. With PL 7, this requirement can be met via the batch identification. Storage and handling Storage in the tightly sealed original container at 15 to 25 °C is recommended. According to TRGS 510, the solution is classified in storage class LGK 12 (non-flammable liquids) and is not considered to pose a risk to water. As PL 7 is neither classified as a hazardous substance nor declared as dangerous goods, no special protective measures are required when opening or dispensing it. Nevertheless, safety goggles with side protection are recommended for the safe handling of the reference solution, and the container should be resealed promptly after use to prevent the reference value from shifting due to evaporation or the absorption of CO2 from the air. Typical applications PL 7 is used wherever the calibration of a pH electrode must not only be ‘adequate’ but also verifiable through documentation: Two- or three-point calibration of pH electrodes in the neutral measuring range, in conjunction with the WTW buffer solutions PL 4 and PL 9 Zero-point adjustment of the pH scale as the central reference point for every calibration routine Traceable calibration in accredited testing laboratories according to ISO/IEC 17025 Quality control in pharmaceutical and active ingredient analysis Calibration prior to the analysis of approximately neutral samples, such as drinking water or cell culture media Research institutions with stringent requirements regarding measurement uncertainty For buffer solutions according to DIN 19266-01:2000, the composition is specified directly in the standard. When PL 7 is used in conjunction with PL 4 and PL 9 for a three-point calibration, this trio covers the entire pH range relevant to practical applications, from acidic through neutral to alkaline, with the same accuracy class and the same traceability to PTB/NIST. This simplifies documentation, as all three calibration points are traceable to PTB/NIST. Technical details Trade namePL 7 Buffer systemDisodium hydrogen phosphate, potassium dihydrogen phosphate pH value at 20 °C6.87 (labelling: pH 6.865 according to DIN / pH 6.87 according to NIST) Accuracy± 0.02 pH at 25 °C TraceabilityPTB/NIST StandardDIN 19266-01:2000 Density at 20 °C1.01 g/cm³ Melting point/freezing point-0.3 °C Boiling point100 °C Physical state / Colour / OdourLiquid, colourless, odourless Hazard classification (CLP)Not classified Dangerous goodsNo Storage class (TRGS 510)Class 12 (non-flammable liquids) Recommended storage temperature15-25 °C Container size250 ml Scope of delivery 1 bottle of WTW Standard (DIN/NIST) buffer solution PL 7, 250 ml, with batch number and expiry date Individual requirements and procurement service For a complete three-point calibration, there are also the WTW Standard (DIN/NIST) buffer solutions PL 4 (pH 4.006/4.01) and PL 9 (pH 9.180/9.18). If you carry out daily routine calibration using the technical accuracy class, you will find the WTW technical buffer solution pH 7 with the same pH value in our range. You can find suitable pH electrodes for calibration in our range of electrodes. Our procurement service is on hand to assist you with additional accessories for your pH measurement technology or with individual procurement enquiries.
Content: 250 ml (€11.60 / 100 ml)
IKA T 25 digital LR disperser, for laboratory reactors, up to 2,000 ml, 0020008820
Anyone wishing to prepare emulsions, suspensions or nanoparticle formulations not in an open beaker but in a closed, temperature-controlled laboratory reactor will need a drive that can be integrated into this system. The IKA T 25 digital LR disperser (0020008820) is designed precisely for this purpose: a dedicated drive unit for high-speed dispersion in laboratory reactors, with a volume range of 1 to 2,000 millilitres (based on water) and a speed range of 600 to 25,000 revolutions per minute. Unlike a benchtop disperser for open beakers, it is designed from the outset for mechanical integration into closed reactor systems and is not intended as a stand-alone, ready-to-use laboratory instrument. Powerful drive with infinitely variable speed control The 800-watt motor (500 watts output power) covers a continuously and electronically adjustable speed range from 600 to 25,000 revolutions per minute, displayed via a digital LED display with a deviation of just 1 % from the set target speed. In combination with the appropriate IKA dispersing tools, high shear forces are generated in the narrow shear gap between the rotor and stator, which break down particles and droplets and homogenise liquid phases, the classic operating principle of rotor-stator dispersers. The maximum permissible viscosity of the medium is 5,000 mPa·s, a guideline value that must be taken into account when selecting the dispersing tool and controlling the process. Designed for installation in laboratory reactor systems Unlike free-standing bench-top dispersers, the T 25 digital LR is designed as a drive unit only, which can be mechanically coupled with the special dispersing tools of the KD-LR series. These tools are designed for use in closed laboratory reactors such as the IKA LR 1000 and, thanks to high-quality shaft seals, enable operation under vacuum, which is useful for preventing aerosol and foam formation in media containing surfactants or for processing oxidation-sensitive batches under an inert atmosphere. Neither the dispersing tool nor the reactor itself is included with the T 25 digital LR; both must be purchased separately to suit the specific application. Electronic overload protection and digital display An integrated microprocessor maintains the set speed even when the resistance of the medium changes, for example if the viscosity of a batch increases during the reaction. If the stirring tool becomes suddenly blocked, for example by a jammed particle, an electronic overload protection system switches off the motor and displays an error code; this protects both the motor and the coupled dispersing tool. The unit is designed for continuous operation with a permissible duty cycle of 100 %. Compact design for mounting on a reactor stand Measuring 87 x 271 x 106 millimetres and weighing 2.5 kilograms, the T 25 digital LR can be mounted on a reactor stand to save space. The noise level without the dispersing tool fitted is 75 dB(A). The housing is rated to degree of protection IP 20 and approved for an ambient temperature of 5 to 40 °C. It can be connected to either 220 to 240 volts or 100 to 120 volts at 50 or 60 hertz. Selecting the appropriate dispersing tool Which KD-LR tool is suitable in each individual case depends on the reactor volume, the desired immersion depth and the viscosity range of the medium. The tools in this series feature an extended design so that, even in larger reaction vessels, they reach right down to the bottom of the vessel and continue to disperse effectively there, rather than leaving dead volume unused. As the T 25 digital LR is designed as a drive for different reactor sizes and tool variants, the same drive can often continue to be used when process requirements change, whilst only the dispersing tool is replaced. Typical applications As a drive unit for laboratory reactors, the T 25 digital LR is used wherever dispersion processes must take place under controlled, closed conditions: Production of emulsions and creams under air-exclusion conditions in closed reactors Dispersion and homogenisation of suspensions with controlled temperature regulation Scale-up trials between open beaker stirring and pilot reactors Production of finely dispersed systems with limited sample volumes from 1 millilitre Process development in the pharmaceutical and fine chemicals industries with requirements for reproducibility Technical details Product typeDrive unit for dispersing tools in laboratory reactorsVolume range (H₂O)1 to 2,000 mlMotor power (input / output)800 W / 500 WSpeed range600 to 25,000 rpm, electronically continuously adjustableSpeed deviation1 %Speed displayLED displayMaximum permissible viscosity of the medium5,000 mPa·sNoise level (without dispersing tool)75 dB(A)Permissible duty cycle100 % (continuous operation)Motor protectionElectronic overload protection with error code displayDimensions (W x H x D)87 x 271 x 106 mmArm length / Arm diameter160 mm / 13 mmWeight2.5 kgProtection class (to DIN EN 60529)IP 20Permissible ambient temperature5 to 40 °CPower supply220 to 240 V or 100 to 120 V, 50/60 Hz Scope of delivery 1 x IKA T 25 digital LR drive unit 1 x IEC mains cable 1 x operating instructions Not included are the required dispersing tool from the KD-LR series, the laboratory reactor itself, and a stand for mounting the drive unit. These components must be procured separately to suit the specific application. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service As the T 25 digital LR is designed purely as a drive unit, you will also need a suitable dispersing tool from the KD-LR series and a stand solution to secure the drive in order to operate it on your laboratory reactor. Through our procurement service, we can assist you in selecting the appropriate dispersing tool for your specific application, as well as stand materials, spare parts and accessories for integration into existing reactor systems. Further information and contact details can be found at our procurement service.
IKA C-MAG HS 7 control Magnetic Stirrer with Heating, LCD Display, 20 Litre, 0020002694
As soon as a stirring and heating process is no longer to be carried out merely as a secondary task, but must be documented in a traceable manner, controlled via an interface or regulated based on a temperature measured within the medium, a simple analogue dial reaches its limits. The IKA C-MAG HS 7 control (0020002694) features an LCD display for setpoint and actual values, RS232 and USB interfaces, and a stirring capacity of up to 20 litres; according to IKA, it was awarded the reddot award in 2017. Digital display and interfaces for documented processes Speed and temperature are each displayed on an LCD screen as setpoint and actual values; the display resolution for temperature is 1 Kelvin. The unit can be connected to a control system via the RS232 interface and the USB-B port; the Labworldsoft laboratory equipment software is listed in the range of accessories for this purpose. For laboratory environments with traceability requirements, this is a difference that goes beyond mere usability. Stirring up to 20 litres with automatic direction reversal The speed range extends from 50 to 1,500 revolutions per minute with a deviation of just ±2 % (no load, rated voltage, at 1,500 rpm and 25 °C) and a setting accuracy of 10 revolutions per minute. Automatic direction reversal and interval operation are available, as is viscosity trend measurement, which allows changes in the medium’s viscosity to be monitored during the process. Stirring rods ranging from 30 to 80 millimetres in length can be used; the maximum load on the base is 25 kilograms. Precise temperature control directly within the medium The scope of delivery includes a PT 1000.60 stainless steel temperature sensor; ETS-D5 and ETS-D6 contact thermometers can also be connected. The temperature control accuracy within the medium is ±0.5 Kelvin with the PT1000 probe and as high as ±0.2 Kelvin with the ETS-D6 (measured in each case with 500 ml of water, a 40 mm stirring rod, 600 rpm, 50 °C). A ‘sensor-in-medium’ detection function indicates when the temperature sensor is actually immersed, thereby contributing to process reliability. Typical applications With its digital display, interfaces and precise medium temperature control, the C-MAG HS 7 control is technically suitable for: Syntheses and reactions requiring documented temperature control within the medium Processes with a defined reaction endpoint requiring an accuracy of ±0.5 K or better Stirring processes up to 20 litres with varying viscosity, monitored via viscosity trend measurement Automated or software-controlled laboratory workstations via RS232/USB Quality control with auditable time and temperature profiles Selection guide within the C-MAG series Within the C-MAG family, the ‘control’ version offers a higher level of specification than the analogue version: ModelStirringStirring capacity (H₂O)Heating powerOperation C-MAG HS 7 control (this unit)Yes, 50 to 1,500 rpm20 l1,000 WLCD, PT1000/ETS-D5/ETS-D6, RS232, USB C-MAG HS 7Yes, 100 to 1,500 rpm10 l1,000 WAnalogue scale, LED setpoint temperature C-MAG HS 10Yes, 100 to 1,500 rpm15 l1,500 WAnalogue scale, LED setpoint temperature, plate 260 x 260 mm C-MAG HP 7No, heating plate only10 l1,000 WAnalogue scale, LED setpoint temperature If you do not require the interfaces or precise media temperature control, the C-MAG HS 7 or the C-MAG HS 10 offer a more cost-effective solution. If you already know that processes are to be documented or controlled via software, opting for the ‘control’ version will save you the expense of retrofitting at a later date. Differences from comparable IKA stirrers Compared to the simpler IKA C-MAG HS 7, the ‘control’ version offers an additional LCD display, interfaces and a larger 20-litre stirring capacity. The IKA C-MAG HS 10 retains analogue operation but features a larger 260 x 260 millimetre plate for higher heating power. At the single-station level, with comparable digital capabilities, the IKA Plate (RCT digital) with an LCD display and aluminium base, and the RET control-visc white with an additional weighing function are also available, each with its own specific focus. Technical details Number of stirring stations1 Max. stirring capacity (H₂O)20 l Maximum load25 kg Motor power output9 W Direction of rotationclockwise / anti-clockwise, automatic reversal possible Speed range50 to 1,500 rpm, setting accuracy 10 rpm, deviation ±2 % Stir bar length30 to 80 mm Heating power1,000 W Heating temperature rangeRoom temperature to 500 °C, setting accuracy 5 K, display resolution 1 K Connection for external temperature sensorPT1000, ETS-D5, ETS-D6 Control accuracy in the medium (PT1000 / ETS-D6)±0.5 K / ±0.2 K Safety circuit adjustable100 to 650 °C Additional functionsInterval operation, viscosity trend measurement, timer (1 s to 143,940 min), probe-in-medium detection InterfacesRS232, USB-B Self-heating on the work surface (ambient temperature 22 °C, 1 hour of maximum stirring)+2 K Base material / dimensionsCeramic, 180 x 180 mm Standby power consumption2 W Dimensions (W x H x D)220 x 88 x 354 mm Weight4 kg IP ratingIP 21 (DIN EN 60529) Awardreddot award 2017 Mains connection220 to 230 V, 50/60 Hz, 1,020 W (other voltage variants: 115 V / 100 V available) Scope of delivery 1 x IKA C-MAG HS 7 control magnetic stirrer with heating (0020002694) 1 x PT 1000.60 temperature probe, stainless steel 1 x IKAFLON 30 magnetic stir bar 1 x IKAFLON 40 magnetic stir bar 1 x screwdriver 1 x USB A-to-B cable Use, installation, maintenance and disposal With degree of protection IP 21, the C-MAG HS 7 control is protected against vertically falling dripping water and is designed for operation in a fume hood or on a stable laboratory bench. The temperature of the base surface rises by up to 2 Kelvin during one hour of continuous stirring; this must be taken into account when reading the actual hotplate temperature. The safety circuit can be freely adjusted between 100 and 650 °C and thus adapted to the specific process, rather than being fixed as with simpler models. Before carrying out maintenance work or cleaning the ceramic surface, the unit should be allowed to cool down and disconnected from the mains. At the end of its service life, the device, as an electrical appliance, must be disposed of separately from household waste via the waste electrical and electronic equipment (WEEE) collection scheme; the manufacturer’s WEEE registration number is DE 66784213. Investment rationale: When does the control version pay off? The additional cost compared with the analogue C-MAG HS 7 is particularly worthwhile if temperature profiles need to be documented, read out via RS232 or USB, or controlled within the medium with an accuracy of ±0.5 Kelvin or better. For simple, non-critical heating and stirring processes without a documentation requirement, the additional features are often unnecessary; in such cases, the C-MAG HS 7 or the C-MAG HS 10 with greater heating power is sufficient. If you regularly switch between several workstations using standardised, software-supported process control, the ‘control’ variant pays for itself through the time saved on documentation and calibration. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 10 years upon registration at ika.com/register within 90 days of purchase.Individual requirements and procurement service Additional original accessories are available for the C-MAG HS 7 control if required, such as ETS-D5 or ETS-D6 contact thermometers, support plates, reaction blocks and the Labworldsoft software. Through our procurement service, we also assist you with spare parts and the standardisation of equipment across multiple workstations. Further information and contact details can be found on our procurement service page. Frequently Asked Questions What distinguishes the C-MAG HS 7 control from the standard C-MAG HS 7?The ‘control’ version features an LCD display for setpoint and actual values, RS232 and USB interfaces, automatic direction reversal, viscosity trend measurement and a larger stirring capacity of 20 litres instead of 10 litres. Is a temperature sensor included in the scope of delivery?Yes, the C-MAG HS 7 control comes as part of the scope of delivery with a PT 1000.60 stainless steel temperature sensor. ETS-D5 and ETS-D6 sensors fit the same connection but are available separately. How accurately can the temperature in the medium be controlled?With the supplied PT1000 probe, to within ±0.5 Kelvin; with an optional ETS-D6 probe, to within ±0.2 Kelvin, in each case under the defined measurement conditions specified in the data sheet. Can the safety circuit be adapted to the specific process?Yes, the safety circuit is freely adjustable between 100 and 650 °C, rather than being fixed as in simpler models. Can the device be controlled via software?The RS232 and USB interfaces allow connection to the Labworldsoft software listed in the IKA range of accessories; this enables stirring and heating parameters to be logged centrally rather than being read manually from the device. How should the C-MAG HS 7 control be disposed of correctly?As an electrical appliance, it should be taken to a waste electrical and electronic equipment (WEEE) collection point rather than disposed of with household waste; the manufacturer’s WEEE registration number is listed in the section on ‘Use, installation, maintenance and disposal’.
WTW SenTix 61 glass pH electrode, refillable, DIN connector, 103640
WTW lists a wide range of applications for these glass electrodes: from diluted acids and emulsions through to beer, milk and fruit juice, right up to serum and urine. The WTW SenTix 61 features a glass shaft, a refillable liquid electrolyte and a platinum wire junction. It measures from 0 to 14 pH at sample temperatures of 0 to 100 °C. If there is no built-in sensor, the temperature is entered on the measuring instrument or measured using an external sensor.Platinum wire junction and conical membraneThe glass shaft is 120 mm long and has a diameter of 12 mm. According to WTW, the platinum wire junction ensures optimum electrolyte flow without blockages. The membrane is conical in shape; according to WTW, it is impact-resistant and easy to clean. The membrane resistance at 25 °C is less than 600 MΩ. The reference system is 3 mol/l KCl, Ag+-free and refillable. According to WTW, the liquid electrolyte enables fast response times.Typical applications, according to WTWDiluted acids, salt solutions, emulsions and suspensionsCooling water, dye solutions and electroplating bathsDrinking water, groundwater, swimming pool water, lake water, surface water and seawaterSoil, paper and coffee extractsBeer, lemonade, fruit juice, vegetable juice, wine, mineral water, milk and vinegarHair dye, mouthwash and household cleanersEnzyme solutions, gastric juice, infusion solutions, protein-containing liquids, serum, Tris buffer solutions and urine (pharmaceuticals, biology, medicine)ConnectionThe SenTix 61 has a permanently attached 1 m cable with a waterproof DIN plug (DIN 19262). The variants in this series differ only in terms of plug, cable and temperature sensor; the electrode itself is identical. The choice therefore depends on the input of the measuring instrument. If a longer shaft is needed, the SenTix 91 has a length of 170 mm instead of 120 mm.Refilling and storageThe refill opening remains open during calibration and measurement. A dropper bottle is included, according to the WTW instructions. For short measurement breaks, the electrode is immersed in reference electrolyte (KCl 3 mol/l, Ag+-free) with the refill opening open. Overnight and for longer periods, it stays in the wetting cap, filled with reference electrolyte, with the refill opening closed. According to WTW, storing the electrode in a dry state or in deionised water can cause permanent damage. If the cap has dried out, the electrode needs at least 24 hours in reference electrolyte. As with any pH electrode, strong acids and alkalis, hydrofluoric acid, organic solvents, oils, fats and proteins shorten its service life.Technical detailsTypepH electrode, analogue, liquid electrolyteShaft materialGlassShaft length / shaft diameter120 mm / 12 mmElectrolyteKCl 3 mol/l, Ag+-free, refillableJunctionPlatinum wireMembrane shapeConicalpH measuring range0 to 14Temperature range0 to 100 °CMembrane resistance< 600 MΩ at 25 °CTemperature sensorNoneConnectionDIN plug (DIN 19262), waterproofCable1 m fixed cableScope of delivery1 WTW SenTix 61 pH electrode with wetting capDropper bottle for refilling (included according to the WTW instructions)1 m fixed cable with DIN plug, permanently attached to the electrodeAccessories and procurement serviceReference electrolyte KCl 3 mol/l for refilling and buffer solutions for calibration are also available. If you require a different version or multiple electrodes, please enquire via the procurement service.
IKA C-MAG HS 7 Package Magnetic Stirrer with Heating, Ceramic Plate, incl. ETS-D5 and Stand Accessories, 0010016454
Anyone setting up a laboratory workstation from scratch does not want to have to search for the base unit, temperature probe and stand components separately across different orders and check them for compatibility. The IKA C-MAG HS 7 Package (0010016454) combines the tried-and-tested C-MAG HS 7 heating magnetic stirrer with an ETS-D5 contact thermometer, a stand rod, a support rod and a boss head into a ready-to-use combination, thereby saving the hassle of ordering and assembling each component separately. Tried-and-tested base unit with 1,000 watts of heating power The technical specifications of the base unit included in the package correspond to those of the C-MAG HS 7, which is available separately: 10-litre maximum stirring capacity, 1,000-watt heating power, a heating temperature range of 50 to 500 °C with 5 Kelvin setting accuracy, and a 180 x 180-millimetre ceramic base. The stirring drive covers a speed range of 100 to 1,500 revolutions per minute via a six-step scale, whilst a fixed safety circuit limits the hotplate temperature to a maximum of 550 °C. ETS-D5 contact thermometer already included in the set Unlike the C-MAG HS 7, which is available separately, this package already includes an ETS-D5 electronic contact thermometer. It can be connected directly via the DIN 12878 connection socket and enables temperature control within the medium rather than just on the plate surface, a feature that would need to be retrofitted separately if the base unit were purchased on its own. Stand accessories for immediate installation of the sensor For the mechanical mounting of the contact thermometer, the package includes an H 16 V stand rod, an H 38 support rod and an H 44 boss head, so that the probe can be fixed directly above the stirring vessel without the need to purchase additional stand components. Same operation as with the single unit Despite the additional components, the operation of the base unit itself remains unchanged: speed and heating temperature are still adjusted via two separate controls; the six-step scale for speed and the rotary knob for heating temperature remain identical to those on the standard C-MAG HS 7. Anyone who has already worked with a C-MAG HS 7 will find their way around this package without needing any training; the contact thermometer is an additional, but independent, feature. Typical applications As a fully equipped set, the C-MAG HS 7 Package is technically suitable for: Setting up new laboratory workstations without existing stand or probe accessories Syntheses and reactions with temperature control directly within the medium from the very first use Training and education laboratories that require a complete, ready-to-use kit Replacement procurement for workstations where the main unit and accessories are replaced together Batches of up to 10 litres requiring a reproducible medium temperature Selection guide: Package or individual unit Whether the package or the individual C-MAG HS 7 offers better value for money depends primarily on whether the laboratory already has temperature sensors and stand equipment: VersionBasic unitETS-D5 sensorStand accessoriesSuitable forC-MAG HS 7 Package (this product)includedincludedincluded (H16V, H38, H44)New installation without existing accessoriesC-MAG HS 7 (single unit)includedto be procured separatelyto be procured separatelyExisting laboratories with existing accessories Anyone who already has stand material and a compatible temperature sensor will save money by purchasing the basic unit on its own rather than the package, as they won’t have to pay for duplicate accessories. Differences from the other C-MAG-HS-7 models The IKA C-MAG HS 7 offers the same base unit without a sensor or stand accessories, for laboratories that already have these components. For those who, in addition to the package’s standard features, require an LCD display, interfaces and a larger 20-litre stirring capacity, the IKA C-MAG HS 7 control is available. For larger installation areas of up to 260 x 260 millimetres, the IKA C-MAG HS 10 is available. Technical details Number of stirring positions1Max. stirring capacity (H₂O)10 lMaximum load15 kgMotor power output1.5 WSpeed range100 to 1,500 rpm, scale 0 to 6Maximum stir bar length80 mmHeating power1,000 WHeating temperature range50 to 500 °C, rotary knob, setting accuracy 5 KSafety circuit fixed550 °CConnection for an external temperature sensorETS-D5 (DIN 12878), included in the setBase materialCeramicDimensions of the installation area180 x 180 mmPermissible relative humidity80 %Dimensions of the main unit (W x H x D)220 x 105 x 335 mmWeight of the main unit5 kgIP ratingIP 21 (DIN EN 60529)Mains connection230 V, 50/60 Hz, 1,020 W (other voltage options available: 120 V / 100 V) Scope of delivery 1 x IKA C-MAG HS 7 base unit with heating 1 x IKA ETS-D5 electronic contact thermometer (IKA No. 0025008371) 1 x IKA H 16 V stand rod (IKA No. 0001545100) 1 x IKA H 38 support rod (IKA No. 0003547700) 1 x IKA H 44 boss head (IKA No. 0002437700) 1 x IKAFLON 20 magnetic stir bar 1 x IKAFLON 30 magnetic stir bar 1 x IKAFLON 40 magnetic stir bar Use, installation, maintenance and disposal With an IP 21 protection rating, the base unit is protected against vertically falling water droplets and is designed for use in a fume hood or on a sturdy laboratory bench. When assembling the stand, the ETS-D5 sensor should be positioned so that it does not collide with the magnetic stir bar during stirring, and its correct reading should be checked against a suitable reference before first use. The boss head and support rod can be readjusted at any time after initial assembly if necessary, without the need to disconnect the main unit from the mains. The ceramic surface is chemical-resistant, but should be allowed to cool before cleaning. At the end of their service life, as electrical appliances, the main unit and contact thermometer must not be disposed of with household waste but must be placed in the separate collection for waste electrical and electronic equipment; the manufacturer’s WEEE registration number is DE 66784213. Investment rationale: a complete set versus purchasing individual items The package is particularly cost-effective when a workstation is being set up from scratch and neither temperature sensors nor stand components are available, as it eliminates the need to procure individual components and check their compatibility. If compatible accessories are already available in the laboratory, for example, from another C-MAG or RCT/RET workstation, it is often more cost-effective to purchase the base unit separately, as this would otherwise result in duplicate accessories included in the package. Where several new workstations are being set up, it is also worth checking whether stand components and sensors can be procured more cost-effectively in bulk from a central source rather than via several individual packages. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Individual requirements and procurement service Additional original accessories are available for the C-MAG HS 7 Package as required, such as extra stirring rods, reaction blocks, carrier plates, replacement stand components or a protective cover for the control panel. Through our procurement service, we can also assist you with spare parts and the standardisation of equipment across multiple workstations. Further information and contact details can be found on our procurement service page. Frequently Asked Questions What vessel sizes are the stand accessories designed for?The stand rod, support rod and boss head are designed for use on the 180 x 180 millimetre mounting surface of the base unit and can be positioned to accommodate standard beaker and flask sizes up to a maximum stirring volume of 10 litres. What is included in the package that isn’t included with the individual C-MAG HS 7?An ETS-D5 contact thermometer, together with a stand rod, a support rod and a boss head for securing the probe, all with their own IKA number. Is the base unit included in the package technically identical to the individual C-MAG HS 7?The technical specifications of the base unit in the set (10 litres, 1,000 watts, 50 to 500 °C, ceramic plate 180 x 180 mm) are the same as those of the C-MAG HS 7, which is available separately. Does the ETS-D5 contact thermometer need to be calibrated separately?Before its first operational use, it is recommended that it be checked against a suitable reference temperature; factory calibration is not specifically mentioned in the manufacturer’s instructions. Can the stand accessories also be used with other IKA stirrers?The stand rod, support rod and boss head are standard components from the IKA range of accessories and are generally compatible with other C-MAG and RCT/RET models, meaning that synergies can be exploited should the workstation be expanded at a later date. Can the main unit be operated without the ETS-D5 sensor?Yes, the heating can be controlled via the plate temperature regardless of the sensor connected; the sensor is an optional extra for monitoring the medium temperature. How should the package be disposed of correctly?As electrical appliances, the main unit and the contact thermometer should be taken to a collection point for waste electrical and electronic equipment rather than being disposed of with household waste; the manufacturer’s WEEE registration number is listed in the section on ‘Use, installation, maintenance and disposal’.
Bandelin SONOREX SUPER RK 100 H ultrasonic bath with heating, 3 litres, 312
Where instruments or small parts also need to be cleaned of grease and residues using heat, a cold ultrasonic bath is often not sufficient. The Bandelin SONOREX SUPER RK 100 H features its own heating system within its compact 3.0-litre capacity, making it the smallest heated model in the SUPER RK series.Heating from 30 to 80 °CThe 140-watt heater covers a temperature range of 30 to 80 °C and is fitted with dry-run protection, which switches the heater off as soon as there is insufficient liquid in the tank. Combined with an operating frequency of 35 kHz, a peak power of 320 watts and a nominal power of 80 watts, it can remove dirt that would otherwise require more time or a more aggressive cleaning agent at room temperature.One vibration system for 2.0 litres of working capacityThe total capacity of 3.0 litres (working capacity 2.0 litres) is subjected to ultrasonic treatment via a single vibration system, whilst the SweepTec function prevents standing waves in the tank. The tank and housing are made of 1.4301 stainless steel; the tank is 1.0 mm thick. The unit is operated via a rotary knob; the cleaning duration and bath temperature can be set independently of one another, whilst the timer ranges from 1 to 15 minutes (± 5 %) or continuous operation.Compact and without a drain connectionAs with the smaller RK 31, the data sheet for the RK 100 H makes no mention of a ball valve; ‘drain: -’ is explicitly stated in the technical specifications. With a capacity of 3.0 litres, the tank can still be easily emptied after cleaning. With external dimensions of 260 x 160 x 250 mm and a net weight of 3.5 kg, the appliance fits easily even on smaller worktops.Decision guide: when is it worth opting for the next size up?The RK 100 H is usually sufficient for individual instruments, spectacles or small tools. If you regularly need to clean several items at once or slightly larger objects, the RK 103 H (4.0 litres), which is slightly larger and fitted with a drain, offers a practical advantage when changing the cleaning solution. For beakers or small sieves, the RK 510 H, with a capacity of 9.7 litres, is the next step up within the SUPER RK series.SUPER RK or smart ST: two ways to achieve the same volumeBandelin also offers the same 3.0-litre tank size in its digital smart ST range, which features a touchscreen, fine-tuned power control and programme memory instead of a rotary knob. Those wishing to save cleaning cycles in a reproducible manner are better off with the smart ST 102 H, whilst those who prefer simple, robust operation without electronics should stick with the RK 100 H. In addition to Bandelin SONOREX, we also offer Elma Elmasonic ultrasonic baths in our range.Use and MaintenanceThe 2.0-litre capacity provides space for the items to be cleaned; if filled to the brim, the tank will overflow when the items are placed inside. A concentrate from Bandelin’s TICKOPUR range is suitable for use as the cleaning fluid and is available separately via the procurement service. As the RK 100 H does not have an automatic degassing function, a short initial run in continuous operation helps to expel dissolved air from freshly prepared liquid before the items to be cleaned are loaded. After the last cycle of the day, the tank should be emptied and wiped down to prevent any cleaning agent residues from settling.Typical applicationsHeat-assisted cleaning of small instruments in practices and laboratoriesDegreasing small metal and plastic partsCleaning spectacles, watches and jewelleryPreliminary cleaning of laboratory glassware prior to further processingFrequently Asked QuestionsWhat temperature does the RK 100 H reach?The heater operates at temperatures ranging from 30 to 80 °C, controlled via the rotary knob.Is there a drain for emptying?No, according to the data sheet, this model does not have a ball valve; the tank is simply tipped out.What is the difference between the RK 100 H and the RK 31?Both are part of the small SUPER RK range; the RK 100 H also has a 140-watt heating element and a slightly larger capacity (3.0 litres instead of 0.9 litres).Is a basket included in the scope of delivery?No, the K 3 C insert basket, the PK 2 C plastic basket and the D 100 lid are available separately.Technical detailsTotal capacity / Working capacity3.0 l / 2.0 lInternal dimensions of the tank (L x W x D)240 x 140 x 100 mmExternal dimensions (L x W x H)260 x 160 x 250 mmWeight (net)3.5 kgUltrasonic frequency35 kHzUltrasonic powerPeak power 320 W, nominal power 80 W, 1 vibration systemHeating power140 W, temperature range 30 to 80 °C, dry-run protectionTimer1 to 15 minutes (± 5 %) or continuous operationOperationRotary knobFunctionsSweepTec, pulse functionTank materialStainless steel 1.4301, thickness 1.0 mmCasing materialStainless steel 1.4301Drainno drain/ball valveMains connection230 V~ (± 10 %), 50/60 Hz, optionally 115 V~, 2 m fixed mains lead, protection class ICurrent consumption230 V 1.0 A / 115 V 2.0 ADegree of protectionIP 32Medical device classClass I (Regulation (EU) 2017/745)ConformityLow Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EUPackaging dimensions365 x 265 x 315 mmScope of delivery1x Bandelin SONOREX SUPER RK 100 H ultrasonic bath with heatingFixed power cable (2 m)Instructions for useThe insert basket and lid are not included in the scope of delivery and are available separately.Individual requirements and procurement serviceThere is a specific procurement requirement for the K 3 C insert basket, the PK 2 C plastic basket, the D 100 lid or a model with a drain such as the RK 103 H. You can use our procurement service to request a quote for suitable accessories, a replacement basket or another model from the SONOREX range.
WTW SenTix 81 precision pH electrode, glass shaft, refillable, 103642
WTW lists a wide range of applications for these glass electrodes: from diluted acids and emulsions through to beer, milk and fruit juice, right up to serum and urine. The WTW SenTix 81 features a glass shaft, a refillable liquid electrolyte and a platinum wire junction. It measures from 0 to 14 pH at sample temperatures of 0 to 100 °C. An NTC temperature sensor (30 kΩ) is fitted.Platinum wire junction and conical membraneThe glass shaft is 120 mm long and has a diameter of 12 mm. According to WTW, the platinum wire junction ensures optimum electrolyte flow without blockages. The membrane is conical in shape; according to WTW, it is impact-resistant and easy to clean. The membrane resistance at 25 °C is less than 600 MΩ. The reference system is 3 mol/l KCl, Ag+-free and refillable. According to WTW, the liquid electrolyte enables fast response times.Typical applications, according to WTWDiluted acids, salt solutions, emulsions and suspensionsCooling water, dye solutions and electroplating bathsDrinking water, groundwater, swimming pool water, lake water, surface water and seawaterSoil, paper and coffee extractsBeer, lemonade, fruit juice, vegetable juice, wine, mineral water, milk and vinegarHair dye, mouthwash and household cleanersEnzyme solutions, gastric juice, infusion solutions, protein-containing liquids, serum, Tris buffer solutions and urine (pharmaceuticals, biology, medicine)ConnectionThe SenTix 81 has a permanently attached 1 m cable with a waterproof DIN plug (DIN 19262) and a 4 mm banana plug for the sensor. The variants in this series differ only in terms of plug, cable and temperature sensor; the electrode itself is identical. The choice therefore depends on the input of the measuring instrument. If a longer shaft is needed, the SenTix 91 has a length of 170 mm instead of 120 mm.Refilling and storageThe refill opening remains open during calibration and measurement. A dropper bottle is included, according to the WTW instructions. For short measurement breaks, the electrode is immersed in reference electrolyte (KCl 3 mol/l, Ag+-free) with the refill opening open. Overnight and for longer periods, it stays in the wetting cap, filled with reference electrolyte, with the refill opening closed. According to WTW, storing the electrode in a dry state or in deionised water can cause permanent damage. If the cap has dried out, the electrode needs at least 24 hours in reference electrolyte. As with any pH electrode, strong acids and alkalis, hydrofluoric acid, organic solvents, oils, fats and proteins shorten its service life.Technical detailsTypepH electrode, analogue, liquid electrolyteShaft materialGlassShaft length / shaft diameter120 mm / 12 mmElectrolyteKCl 3 mol/l, Ag+-free, refillableJunctionPlatinum wireMembrane shapeConicalpH measuring range0 to 14Temperature range0 to 100 °CMembrane resistance< 600 MΩ at 25 °CTemperature sensorNTC 30 kΩConnectionDIN plug (DIN 19262), waterproof, and 4 mm banana plugCable1 m fixed cableScope of delivery1 WTW SenTix 81 pH electrode with wetting capDropper bottle for refilling (included according to the WTW instructions)1 m fixed cable with DIN and banana plugs, permanently attached to the electrodeAccessories and procurement serviceReference electrolyte KCl 3 mol/l for refilling and buffer solutions for calibration are also available. If you require a different version or multiple electrodes, please enquire via the procurement service.
WTW Technical Buffer Solution TPL 7, pH 7.00, 250 ml, 108802
Before a pH electrode can provide reliable readings, it must be calibrated, and this requires a stable technical buffer solution with a pH of 7. The WTW technical buffer solution pH 7.00 provides the neutral reference point for 2- or 3-point calibration, as routinely carried out in laboratories in the pharmaceutical, industrial, research and water analysis sectors. It is available in three container sizes ranging from 50 ml to 1,000 ml, depending on how frequently calibration is carried out and how many electrodes are in use. Why calibrate regularly The glass membrane of a pH electrode changes over time; ageing, deposits or temperature fluctuations cause the slope of the calibration curve to shift. Without regular calibration against a known buffer solution, measured values gradually drift without this being immediately apparent. A fresh technical buffer solution with a defined pH value and documented accuracy is therefore essential for reliable measurement results, regardless of the pH meter or electrode type used. Phosphate buffer with documented accuracy The technical buffer solution pH 7 is based on a phosphate buffer comprising disodium hydrogen phosphate and potassium dihydrogen phosphate. At 20 °C, the pH value is 7.00, with an accuracy of ± 0.03 pH. This tight tolerance ensures reproducible calibration, regardless of the electrode or measuring instrument used. Particularly when several measuring points or sites require the same reference, documented, consistent accuracy forms the basis for comparable results. The neutral reference point for 2- or 3-point calibration In practice, pH 7 is usually the first point in a 2- or 3-point calibration, typically supplemented by pH 4 and pH 10. If you have all three buffer levels in stock, you will fully cover the measurement range relevant to most applications. A simple 1-point calibration at pH 7 only indicates whether the electrode’s zero point is correct, but says nothing about the slope of the calibration curve outside the neutral range. For measurements that must also be reliable in the acidic or alkaline ranges, at least a second calibration point is therefore advisable. The same technical buffer solution is also available with pH 4.01 and, in trace quality, with pH 10.01. WTW, a brand of Xylem The buffer solution is supplied by WTW, an established brand in pH measurement technology and electrochemistry, which is now part of Xylem. Many laboratories already rely on WTW measuring instruments and electrodes; this technical buffer solution is suitable for them as a matched calibration solution. In principle, however, the buffer solution can be used with any pH electrode and any pH meter, regardless of the manufacturer; calibration is not tied to a specific measuring instrument. Pack sizes for the technical buffer solution pH 7 Select the appropriate pack size above: STP 7 as a 50 ml bottle for economical use or as a supplement in an electrode case, TPL 7 with 250 ml for routine laboratory work, and TEP 7 with 1,000 ml for frequent calibration requirements or multiple measuring points. ModelVolume STP 750 ml TPL 7250 ml TEP 71,000 ml Storage, shelf life and handling At 20 °C, the buffer solution has a density of 1.01 g/cm³ and a melting point of -0.3 °C. Unopened, it has a shelf life of 3 years when stored at 15 to 25 °C. It is not classified under GHS/CLP and is not a dangerous good, which significantly simplifies storage, handling and dispatch in day-to-day laboratory work; there are no special dangerous goods requirements or labelling regulations to observe. Avoid contamination To ensure that the calibration remains reliable throughout the entire shelf life, buffer solution that has been removed should not be poured back into the bottle. Even minor contaminants from the measurement environment or the electrode can alter the pH value of the remaining solution and distort subsequent calibrations. For daily use, it is therefore advisable to use a small calibration vessel into which only as much buffer solution is poured as is required for the current calibration. The bottle itself should be kept tightly sealed and stored at a temperature between 15 and 25 °C to ensure that the documented accuracy of ± 0.03 pH is maintained until the end of the three-year shelf life. Typical applications The technical buffer solution pH 7 is used wherever pH electrodes need to be calibrated regularly: Routine calibration of pH electrodes in pharmaceutical quality assurance Water analysis, for example in drinking water and process water monitoring Process control in industry, wherever pH values in the neutral range are monitored Research and teaching, as a reliable reference point for measurement series Commissioning and functional testing of new pH electrodes prior to first use Technical details Buffer systemDisodium hydrogen phosphate, potassium dihydrogen phosphate (phosphate buffer) pH value at 20 °C7.00 Accuracy± 0.03 pH Density at 20 °C1.01 g/cm³ Melting point-0.3 °C Shelf life when unopened3 years Storage temperature15 to 25 °C GHS/CLP classificationNot classified, not a dangerous good Scope of delivery 1 bottle of WTW technical buffer solution pH 7.00 in the selected container size (50 ml, 250 ml or 1,000 ml) Individual requirements and procurement service For complete 3-point calibration, there is also the same technical buffer solution with pH 4.01 and, in trace quality, with pH 10.01, as well as suitable pH electrodes. If you have larger requirements, need custom container sizes or have any questions about the appropriate calibration solution, our procurement service will be happy to assist you.
Content: 250 ml (€6.84 / 100 ml)
Elma Elmasonic Easy 30H Ultrasonic Bath with Heating, 2.7 Litre, 37 kHz, 1117697
Not every cleaning task in the laboratory requires a digital display and programme memory. For pipette tips, small glassware or tools, a simple ultrasonic bath with fixed time settings is often sufficient. With a tank capacity of 2.7 l and a built-in heater, the Elma Elmasonic Easy 30H offers precisely this basic set-up for the laboratory bench, without controls that are not needed in day-to-day use anyway. The Easy series is designed for simple applications where a reliable, quick-to-use device is more important than programmability or multiple ultrasonic modes.Operation via a rotary knobInstead of a digital display and menus, the Easy 30H features an analogue rotary knob with ten fixed time settings ranging from 1 to 30 minutes, as well as continuous operation for up to 6 hours. LED indicators show the operating status; two ultrasonic modes, Eco and Dynamic, cover the vast majority of laboratory cleaning tasks. Those who only clean occasionally or use the unit at different workstations can use it without any training; a second glance at the manual is rarely necessary, and even new staff can be shown how to use it quickly.Compact bath for the laboratory benchThe tank has a capacity of 2.7 l; a working volume of 1.6 l is recommended, with internal dimensions of 220 x 120 x 95 mm. This is sufficient for pipette tips, small glassware, laboratory cutlery or tools, without the need to use a large amount of cleaning solution. A modular cleaning basket 30 (item no. 1108916) holds the items above the base of the tank; an insert lid (item no. 1110262) or a stainless steel lid 30/40 (item no. 1111930) are available as accessories. For larger quantities of similar small parts, a suitable Hostalen tank is also available, which is used in size 30 for the Select and P models as well.Heating and performanceThe integrated heater ranges from 25 to 80 °C with a heating power of 200 watts; the ultrasonic power is 80 watts effective with a peak power of 320 watts. The Easy 30H does not have a drain connection; to empty it, the tank is tilted or the water is scooped out into a separate container. For a unit of this size, this is generally not a disadvantage in everyday laboratory use, as the volume of water remains small. The IP20 protection rating also means that the housing itself is not designed to withstand splashing water; the unit should therefore be placed on a dry surface.Cleaning in day-to-day useA typical cleaning cycle begins by adding the cleaning solution directly into the tank; the appropriate time setting is then selected using the rotary knob, depending on the level of soiling, this ranges from a few minutes to continuous operation. The ‘Dynamic’ mode is suitable for more stubborn residues, whilst ‘Eco’ is designed for gentler routine cleaning with lower energy consumption. As no programmes are saved, the time setting is adjusted each time using the rotary knob; this does not involve any additional effort when there are only a few, clearly recurring cleaning steps.Accessories for different workpiecesDepending on the items to be cleaned, the Easy 30H can be used with a range of accessories. The modular cleaning basket 30 is suitable for loose small parts that should not rest directly on the bottom of the tank; the insert lid seals the tank during operation without obstructing access to the control panel. The optional Hostalen tank serves as an inner liner and protects the stainless steel tank when using more aggressive cleaning agents or changing the bath frequently; this really pays off, particularly with daily use. For training workshops and test laboratories where different tools and small parts are cleaned one after the other, this allows flexible operation using the same basic unit, without the need to maintain a separate tank for each type of part.Choice within the Elma seriesWithin the Easy series, the models differ primarily in tank size; the smaller Easy 10H has a capacity of 0.9 l for very small parts. Those requiring additional programmable sequences or a sweep function will find these in the Select series, whilst those wishing to carry out analytical precision cleaning using two frequencies, 37 and 80 kHz, will find what they need in the P series. We also offer Bandelin SONOREX ultrasonic baths for laboratories that already use this range of equipment.Typical applicationsCleaning of pipette tips and small glass partsCleaning of tools and instruments at training and workshop workstationsCleaning of small laboratory parts in routine operationsGetting started with ultrasonic cleaning without the need for programmingTechnical detailsTotal volume2.7 l (recommended working volume 1.6 l)Internal dimensions of tank (W x D x H)220 x 120 x 95 mmExternal dimensions (W x D x H)305 x 190 x 230 mmWeight3.3 kgUltrasonic frequency37 kHzUltrasonic power80 W effective, 320 W peakHeating power200 WTemperature range25 to 80 °COperating modesEco, DynamicTimerRotary knob, fixed settings: 1/2/3/4/5/10/15/20/25/30 minutes or continuous operation for up to 6 hoursTank materialStainless steelDrainNo drain connectionMains connectionIEC power connector 220 to 240 V~, 50/60 Hz, 2 m power cableProtection ratingIP20, protection class IScope of delivery1x Elma Elmasonic Easy 30H ultrasonic bathPlastic lidPower cable (2 m)Operating instructionsThe cleaning basket, insert lid and stainless steel lid are not included in the scope of delivery and are available separately.Individual requirements and procurement serviceFor the matching cleaning basket 30, insert lid or stainless steel lid, as well as the Hostalen tank, our procurement service can assist you.
WTW digital IDS pH electrode SenTix 940, plastic shaft, 1.5 m fixed cable, 103740
With a digital IDS electrode, the calibration data is stored in the sensor, not in the measuring instrument. According to the WTW instructions, the electronics in the head store the sensor type, serial number and the last 10 calibrations. As a result, the correct slope and asymmetry automatically apply on the connected measuring instrument, and several calibrated sensors can be swapped on one instrument without recalibration. The WTW SenTix 940 has a gel electrolyte and a plastic shaft.Gel without refillingThe shaft is made of PPE/PS, is 120 mm long and has a diameter of 12 mm. The gel electrolyte is not refilled, and the electrode is low-maintenance. According to WTW, the fibre junction prevents blockages. The membrane is cylindrical, and according to WTW its resistance is below 1 GΩ. It measures from 0 to 14 pH at sample temperatures of 0 to 80 °C.Temperature recorded at the same timeAn NTC temperature sensor (30 kΩ) is built in, so a second sensor in the sample vessel is not needed. According to WTW, the IDS measuring electronics work with an accuracy of pH ±0.004, ±0.2 mV, ±0.1 °C (±1 digit in each case).Typical applications according to WTWSwimming pool waterWastewater in general, industrial wastewater and electroplating wastewaterGroundwaterLake water, surface water and seawaterConnection to the measuring instrumentThe SenTix 940 has a permanently attached cable of 1.5 m. The IDS plug is a 4-pin, waterproof plug connection with locking. The versions 940, 940-3 and 940-P have the same electrode and differ only in the connection. Which one is suitable depends on the distance between the sample and the measuring instrument.StorageBefore the first measurement, the wetting cap is removed, and gas bubbles behind the membrane are removed by shaking. During short breaks, the electrode is immersed in reference electrolyte (KCl 3 mol/l, Ag+-free); overnight and for longer, it stays in the wetting cap filled with it. If stored dry or in deionised water, it can be permanently damaged according to WTW. If the liquid in the cap has dried out, the electrode needs at least 24 hours in reference electrolyte. Strong acids and alkalis, hydrofluoric acid, organic solvents, oils, fats and proteins shorten the service life, as with any pH electrode.Technical detailsTypepH electrode, digital (IDS), gel electrolyteShaft materialPlastic (PPE/PS)Shaft length / shaft diameter120 mm / 12 mmElectrolyteGel, not refillableJunctionFibreMembrane shapecylindricalpH measuring range0 to 14Temperature range0 to 80 °CMembrane resistance< 1 GΩTemperature sensorNTC 30 kΩ, built inAccuracy of IDS electronicspH ±0.004, ±0.2 mV, ±0.1 °C (±1 digit in each case)ConnectionIDS plug, 4-pin, waterproof and lockableCable1.5 m fixed cableScope of delivery1 WTW SenTix 940 pH electrode with wetting capOperating instructionsFixed cable 1.5 m with IDS plug, permanently attached to the electrodeRegulatory informationAs an electrical device, the digital IDS electrode falls under the ElektroG. The manufacturer Xylem Analytics Germany GmbH (WTW brand) is registered under the WEEE registration number DE 29884659. How to return old appliances is described on the page Environment and disposal.Accessories and procurement serviceAlso available are reference electrolyte KCl 3 mol/l for the wetting cap and buffer solutions for calibration. For other IDS electrodes or larger quantities, there is the procurement service.
IKA lab dancer Test Tube Shaker, Touch Function, 2,800 rpm, 0003365000
Briefly mixing a single test tube before the sample goes into the photometer: for this, a whole orbital shaker does not have to start up and no speed has to be set. The IKA lab dancer is tailored to exactly this moment. The tube is pressed by hand against the rubber pad, the touch function immediately starts the circular motion, and on release it stops just as immediately. With a shaking stroke of 4.5 mm and a fixed speed of 2,800 revolutions per minute, the unit covers the classic vortex application for small vessels up to 30 mm in diameter, from test tubes through centrifuge tubes to microtubes. Touch operation for individual tubes Unlike a continuous-running unit with display and timer, the lab dancer has neither a speed display nor a timer. This is not a sacrifice but the concept behind it: anyone who briefly mixes several individual samples one after another, for example before a dilution series or between two pipetting steps, does not need to set any parameters. Press the tube down, wait a few seconds, done. The fixed speed of 2,800 rpm is strong enough for most routine tasks without any control being necessary. With a permissible duty cycle of 100 %, several tubes can be processed directly one after another without the drive having to cool down in between. Compact design for the workstation At 100 x 70 x 100 mm and a weight of only 0.776 kg, the lab dancer takes up hardly any bench space and can be placed directly next to the centrifuge, pipette or photometer, where it is actually needed in the workflow. The power supply is via a supplied 12 V plug-in power supply, which handles input voltages of 100 to 240 V at 50/60 Hz. This allows the unit to be operated at practically any laboratory workstation without an additional voltage converter, even when moving between locations with different mains voltages. Less repetitive movement in everyday laboratory work Anyone who mixes many individual samples one after another every day often resorts to manual shaking by hand without a vortex mixer. The touch function of the lab dancer takes over this repetitive movement: pressing instead of shaking, across any number of individual samples with consistent intensity. This relieves the strain above all in series with many small batches, for example in sample preparation before a measurement series, and at the same time ensures more even mixing than by hand, because stroke and speed remain identical for every operation. Typical applications As a benchtop unit for the quick individual operation, the lab dancer finds its place above all where brief mixing is needed several times a day without a larger orbital shaker being worthwhile: Mixing reagents in test tubes before photometric measurement Resuspending cell pellets in centrifuge tubes after centrifugation Brief mixing of individual samples in routine analysis Homogenising small volumes in tubes between individual pipetting steps Dissolving reagent tablets or powder samples in small vessels Selection guide: which type of shaker is suitable lab dancer, Vortex 2 and ROCKER 3D digital cover three different types of movement at IKA. Which unit is suitable depends on whether individual tubes are to be mixed briefly, larger batches shaken in continuous operation, or sensitive samples moved gently. ProductType of movementSpeed / angleShaking loadOperationlab dancer (this product)circularfixed, 2,800 rpm0.1 kgTouch functionVortex 2circular500 to 2,500 rpm, adjustable0.4 kgTouch or continuous operationROCKER 3D digitalwobbling0 to 80 rpm, tilt angle 0 to 15°2 kgTimer or continuous operation For individual small vessels up to 30 mm diameter and quick in-between use, the lab dancer is suitable. Anyone who regularly mixes larger quantities in continuous operation or needs attachments for plates and flasks will find the more suitable solution in the Vortex 2, and for gentle wobbling of larger vessels the ROCKER 3D digital is better suited. Technical details Type of movementcircularShaking stroke4.5 mmPermissible shaking load (incl. attachment)0.1 kgSpeedfixed, 2,800 rpmMotor power input1.2 WMotor power output0.8 WPermissible duty cycle100 %Touch functionyesPermissible ambient temperature range5 to 40 °CPermissible relative humidity80 %Dimensions (W x H x D)100 x 70 x 100 mmWeight0.776 kgConnection values100 to 240 V, 50/60 Hz, device power consumption 30 W (incl. 12 V plug-in power supply)IP ratingIP 40 (DIN EN 60529) Scope of delivery 1 x IKA lab dancer test tube shaker 1 x 12 V plug-in power supply Differences from the neighbouring series Anyone who wants to move whole flasks, culture flasks or microtitre plates in an orbital motion instead of individual tubes is in the wrong place with the lab dancer design. For this, we offer the IKA hula dancer series, for example the hula dancer basic or the hula dancer digital with adjustable speed. Both are intended for larger, flat set-ups instead of individual small vessels. An overview of all mixers, stirrers and shakers in the range is offered by the category Mixers, stirrers and shakers. Application, installation and maintenance The lab dancer is designed for operation at 5 to 40 °C and a relative humidity of up to 80 %, and degree of protection IP 40 protects against larger foreign objects but not against splashing water. A dry, level laboratory bench within reach of the other work steps is sufficient as a location, and a stand or fixed mounting is not necessary. Maintenance is essentially limited to cleaning the rubber pad on which the tubes rest, especially after contact with aggressive or staining reagents, to avoid carry-over between different samples. Since the unit stands directly on the work surface without a stand, a fixed, easily accessible place near the rest of the sample preparation is worthwhile, so that reaching for the lab dancer does not become a work step of its own. At the end of its service life, the unit as small electrical equipment belongs in the separate collection of waste electrical equipment and not in household waste. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service Factory calibration certificates and qualification documents (IQ/OQ) are available for the lab dancer, for example for laboratories with documented equipment testing. Do you need one of these documents, an additional plug-in power supply as a spare part or support in choosing between lab dancer, Vortex 2 and ROCKER 3D digital for your specific application? Through our procurement service, we support you with procurement and configuration. Frequently asked questions For which vessels is the lab dancer suitable?For small vessels up to 30 mm diameter, such as test tubes, centrifuge tubes and microtubes. Can the speed be set?No, the lab dancer runs at a fixed speed of 2,800 rpm. Anyone who needs an adjustable speed between 500 and 2,500 rpm will find it in the Vortex 2. Is a power supply included in the scope of delivery?Yes, the lab dancer is supplied with a 12 V plug-in power supply for 100 to 240 V, so a separate purchase is not necessary. How is the lab dancer operated?Via the touch function: the tube is pressed against the rubber pad, which starts the circular motion, and on release it stops again immediately. Is the unit suitable for continuous operation?The permissible duty cycle is 100 %, but the touch principle is designed for short individual operations. For genuine continuous operation with several attachments, the Vortex 2 is the more suitable choice. What degree of protection does the lab dancer have?IP 40 according to DIN EN 60529, suitable for normal laboratory operation, not for damp rooms or splash areas. Can several tubes be mixed at the same time?The lab dancer is designed for one vessel per operation, and the permissible shaking load of 0.1 kg corresponds to the weight of a filled small vessel up to 30 mm in diameter.
Kern OIV 345 digital video microscope, 11.6-inch HD display (PC-free)
The Kern OIV 345 is a video microscope without an eyepiece. The camera and optics are housed in a head mounted on a mechanical column stand, and the image appears on a built-in 11.6-inch display. It is operated using the supplied wireless USB mouse; a computer is not required for operation. Kern describes it as a video microscope with axial optics for digital stereomicroscopy, which displays samples clearly on the screen.Display instead of eyepieceThe LCD measures 11.6 inches with a resolution of 1,920 x 1,080 pixels (HD) and, according to the brochure, can be tilted from 0 to 45°. It is made of toughened glass and has no edges, which makes cleaning easier. The display unit measures 275 x 170 x 12 mm. According to Kern, the menu languages include German, English, French, Italian and Russian. The integrated camera software captures images and videos, processes and documents them, and takes measurements.Click-stop zoomThe zoom range is from 0.7x to 4.5x, with a zoom ratio of 6.4:1. It also has a fixed 0.5x objective. The data sheet specifies a standard total magnification range of 15.96x to 102.6x, with a field of view measuring 2.3 to 14.77 mm. The zoom wheel has an integrated click-stop that locks into defined steps. According to Kern, this helps with selecting the magnification and calibrating the documentation functions in the software. Torque control is provided.Camera and lightingThe camera has a 5 MP Sony CMOS sensor in 1/2.8-inch format and delivers 60 frames per second; it uses a rolling shutter. The light comes from a 3 W LED ring in incident light mode, which can be dimmed continuously. The contrast method is bright field. The working distance is 100 mm, and the maximum specimen height is 110 mm. The mechanical stand has a column height of 330 mm; focusing is carried out via a coarse focus mechanism.Storage, connections and PC softwareRecordings can be saved to the included 32 GB USB stick or to a microSD card. Connectivity options include HDMI, two USB 2.0 ports and a microSD card slot. An additional monitor can be connected via HDMI, allowing the live feed to be displayed on two devices. The image can be viewed and analysed on a PC or laptop via USB; according to Kern, the S-VIEWER (OXM 904) software is available to download free of charge for this purpose. The data sheet lists the following system requirements: an Intel Core i3 or higher CPU, or an AMD Ryzen 5 or higher CPU; 8 GB of RAM; a 128 GB SSD; a graphics card (the data sheet names NVIDIA GeForce RTX 3060 and AMD Radeon RX 6600); and a 13-inch Full HD display running at 2.5 GHz.Power supply and dimensionsThe desktop power supply is detachable, has a C14 IEC connector and operates at 100 to 240 V at 50/60 Hz; the device receives 12 V at 2,000 mA. The power cable is 2.5 m long. The unit measures 320 x 260 x 450 mm and has a net weight of approx. 4.4 kg. It may be stored at temperatures between -5 °C and 40 °C.Typical applicationsQuality control and materials testing: jointly assessing solder joints and component edges on the displayElectronics and semiconductor industryEducation and research: several people view the same imageMineralogy and tissue preparationDetection of parasitesTechnical detailsOptical systemAxial, without eyepiece (display)Zoom0.7x to 4.5x, ratio 6.4:1, click-stop; fixed 0.5x objectiveStandard total magnification15.96x to 102.6xField of view2.3 mm to 14.77 mmWorking distance100 mmMaximum sample height110 mmContrast methodsBright fieldIlluminationLED ring in incident light, 3 W, continuously dimmableCameraSony CMOS, colour, 5 MP, 1/2.8 inch, 60 frames per second, rolling shutterDisplay11.6-inch LCD, 1,920 x 1,080 HD, tempered glass, tilt 0° to 45°; display unit 275 x 170 x 12 mmStandMechanical column stand, column height 330 mm, coarse focus, torque controlInterfacesHDMI, USB 2.0 (2 ports), MicroSD card slotMemory32 GB USB stick included in the scope of deliverySoftwareintegrated camera software; S-VIEWER (OXM 904) for the PCPower supplyDesktop power supply (detachable, IEC connector C14), 100 to 240 V AC, 50/60 Hz; device 12 V / 2,000 mA; cable 2.5 mMains plugEuro included in the scope of delivery; UK, US and CH adapters optionalDimensions (W x D x H)320 x 260 x 450 mmNet weightapprox. 4.4 kgStorage temperature-5 °C to 40 °CLabellingCEWarranty (manufacturer)36 months according to Kern, excluding wear partsScope of deliveryOIV 345 video microscope with display and mechanical standDesktop power supply with Euro plugWireless USB mouseUSB stick, 32 GBDust coverMultilingual operating instructionsWarrantyAccording to Kern & Sohn, this microscope comes with a 3-year warranty. Kern grants 3 years on products with a list price of €500 or more and 2 years on products below that and on components; wear parts such as batteries and rechargeable batteries are excluded. Warranty repairs are carried out by Kern or by a Kern dealer.DownloadsOperating instructions Kern OIV-3 (PDF)Regulatory informationAs an electrical device, the microscope falls under the ElektroG. The manufacturer Kern & Sohn GmbH is registered under the WEEE registration number DE 80821200. How to return old appliances is described on the page Environment and disposal.Individual requirements and procurement serviceThe attachment lenses OBB-A3225, OBB-A3226 and OBB-A3240, the solder protection lens OBB-A3227, the microscope stand OIV-A3001, the cleaning spray OCS-A1101, the cleaning kit OCS 901, the calibration slide ODC-A2404, the software OXM 904 (S-VIEWER) and the IEC power cables 822-903 (UK), MLB-A09 (US) and YKK-01 (CH) are also available. Enquiries are handled via our procurement service.
KNF LABOPORT N 840 G, chemical-resistant diaphragm vacuum pump, 34 l/min, ATEX marking category 2, 317123
For those in the laboratory who require a higher flow rate than the smaller N 820 G can provide, the KNF LABOPORT N 840 G is a chemical-resistant, oil-free diaphragm vacuum pump with a flow rate of 34 l/min. It covers the higher performance range of the LABOPORT N series and is suitable for applications requiring a higher flow rate, such as larger vacuum chambers or filtration set-ups. Chemical-resistant materials in the parts in contact with the medium As with the smaller version, the pump head is made of TFM PTFE, the diaphragm is PTFE-coated, and the valves are made of FFPM. This combination of materials makes the N 840 G suitable for handling and evacuating highly aggressive and corrosive gases and vapours. The maximum operating pressure is 0.1 bar (rel.), and the ultimate vacuum is 6 mbar (abs.), identical to the smaller version. Stepless speed control and gas ballast valve The integrated, manual speed control allows the flow rate to be adjusted to suit the specific application. The integrated gas ballast valve supports short process times, even when working with high-boiling-point solvents, by reducing the condensation of vapours in the pump head. A 3-colour status indicator shows the operating status (running, standby, fault) at a glance. Explosion protection for internal areas in contact with the medium The N 840 G bears the ATEX marking (Ex) II 2/-G IIB+H2 T3 and is therefore designed for pumping in potentially explosive atmospheres. This marking refers exclusively to the internal, media-contacting area of the pump, not to the installation environment. More power, more weight Measuring 177 x 240 x 289 mm (W x H x D) and weighing 11.3 kg, the N 840 G is slightly larger and heavier than the N 820 G, in line with its higher flow rate. It is powered directly from the mains (100 to 240 V AC, 50/60 Hz), requires no battery, and has a power consumption of 100 W. A thermal switch and a mains fuse protect the pump against overload; the degree of protection is IP30. Permissible media and ambient temperatures range from +5 to +40 °C. Low-maintenance in everyday laboratory use As the diaphragm vacuum pump operates completely oil-free, there is no need for the regular oil changes required by conventional rotary vane pumps, and there is no risk of oil mist entering the gases being pumped or the laboratory air. This makes the N 840 G a clean vacuum source for applications where contamination-free operation is important, such as when filtering samples or evacuating larger set-ups. A thermal switch and mains fuse provide additional protection against overload during continuous operation, making it suitable for longer process times and higher flow rates in everyday laboratory use. Connection and common size The hose connection has an internal diameter (ID) of 9.5 to 8 mm and is made of PVDF. The pump head of size 840 is also listed by the manufacturer under reference number 315994, the same identification number used for the structurally identical drive unit of the SR 840 G and SH 840 G system variants. Anyone who already has experience with one of these system variants of size 840 will therefore also be familiar with the drive unit of the N 840 G. Typical applications As a purely oil-free diaphragm vacuum pump, the N 840 G covers a wide range of laboratory applications requiring higher flow rates: Conveying and evacuating aggressive or corrosive gases and vapours requiring higher flow rates Vacuum filtration of larger set-ups Evacuating desiccators and vacuum chambers Vacuum supply for drying and vacuum ovens N, SR or SH: choosing the right configuration The N 840 G delivers a pure vacuum without the need for additional accessories. For those who also wish to collect condensate or solvent vapours on the suction and discharge sides, the SR 840 G system variant (with two separator flasks) provides a suitable extension. If the recovery of solvents through condensation is the primary objective, the SH 840 G system variant (with separator and high-performance condenser) is the more suitable choice. For those who only require 20 l/min, the more compact N 820 G is available in the same series. Designed for continuous operation With a power consumption of 100 W and a stable power supply across the wide range of 100 to 240 V AC, the N 840 G can be operated at different mains voltages without the need for an additional voltage converter. In combination with the stepless speed control and the gas ballast valve, it is therefore also suitable for more demanding, longer-running vacuum applications in the laboratory where a higher flow rate is required. Technical details Flow rate (max.)34 l/min (2.04 m³/h) Ultimate vacuum (max.)6 mbar (abs.) Operating pressure (max.)0.1 bar (rel.) Pump headTFM PTFE DiaphragmPTFE-coated ValvesFFPM Voltage100 to 240 V AC, 50/60 Hz Power P1100 W Operating current1.0 A (100 V AC) / 0.6 A (240 V AC) Degree of protectionIP30 Permissible medium/ambient temperature+5 to +40 °C Dimensions (W x H x D)177 x 240 x 289 mm Weight11.3 kg Hose connectionID 9.5 to 8, PVDF ATEX marking (internal areas in contact with the medium)(Ex) II 2/-G IIB+H2 T3 Scope of delivery 1x KNF LABOPORT N 840 G diaphragm vacuum pump Wrench for hose connection Silencer Individual requirements and procurement service A suitable spare parts kit is available for the N 840 G. If you have any questions regarding suitable accessories, spare parts or individual requirements relating to your KNF LABOPORT N 840 G, our procurement service will be happy to assist you.
Bürkle Hand Pump for Solvents, V2A Stainless Steel, for Containers up to 60 L, 5603-1000
Anyone who scoops solvent from a 60-litre drum using a beaker or a jug risks splashes and direct skin contact with the liquid. The hand pump for solvents, on the other hand, operates on the principle of positive pressure: A pump ball forces air into the sealed drum; the resulting overpressure pushes the solvent out in a controlled manner through the fixed spout. This allows flammable solvents to be dispensed in measured quantities without having to tip the drum over or leave it open permanently.Operation without suctionUnlike a suction pump, the hand pump does not create a vacuum in the riser tube, but rather positive pressure inside the drum itself. The pump bulb is operated by hand; air flows through a tube into the drum, whilst the solvent rises separately to the spout. The shut-off valve at the end of the spout, made of stainless steel and PTFE, stops the flow immediately once the receiving container is full.For drums up to 60 l with a G2-inch threadThe pump fits containers with a G2-inch external thread and a capacity of up to approximately 60 l. The dip tube can be continuously adjusted to the actual depth of the drum; at full immersion depth, it extends up to 60 centimetres into the drum. With a flow rate of around 10 l per minute and a viscosity of up to 500 mPa·s, the pump is suitable for low- to medium-viscosity solvents. The 12-millimetre external diameter of the outlet fits standard funnels and canister openings, allowing the target container to be filled directly beneath the outlet elbow.Materials in contact with solventsAll parts in contact with the medium are made of 1.4301 (V2A) stainless steel and PTFE. Both materials are chemically resistant to organic solvents and aromatic compounds and can withstand regular cleaning after filling. Unlike a plastic pump, stainless steel does not swell when frequently exposed to more aggressive solvents and retains its fit, even after many filling cycles.Independent of mains power and compressed airThe hand pump requires neither a mains power connection nor a compressed air supply; it operates solely by means of the pump ball in the hand. This makes it a suitable option for workplaces where there is no compressed air network, such as in smaller workshops, for mobile operations or in storage areas away from the main infrastructure. Those who only open a drum occasionally can therefore manage without having to purchase a compressor.Safety when handling flammable liquidsBürkle expressly refers to the explosion protection guidelines for handling flammable, highly combustible liquids when using this pump: all parts must be earthed; in addition, the manufacturer recommends an anti-static kit. The advice is a recommendation for safe operation.If a different container or drive type is requiredFor tinplate canisters with bellows closures, the solvent pump for tinplate canisters is available as a hand pump of identical design, featuring a suitable adapter instead of a G2-inch thread. If both hands need to remain free, or if larger 220-litre drums are being used, the foot-operated solvent pump with spout is the more suitable choice. For small containers such as bottles or canisters up to 10 l with a GL45 thread, the Mini solvent pump is more suitable.Typical applicationsContamination-free dispensing of organic solvents and aromatic compounds from 60-litre drumsPrecise dispensing of flammable liquids in the laboratory, workshop or warehouseDecanting into smaller containers without tilting or opening the drumDrums with G2-inch threads in the chemical industry and in tradeTechnical detailsMaterialStainless steel 1.4301 (V2A), polytetrafluoroethylene (PTFE)Drive typemanually operatedPump typePositive pressure pumpThreadG 2 inches, external threadFlow rate approx.10 l/minViscosity up to approx.500 mPa·sPipe diameter15 mmImmersion tube diameter15 mmLength of outlet bend185 mmOuter diameter of outlet12 mmMax. immersion depth60 cmFor containers up toapprox. 60 lScope of deliveryHand pump with fixed spout and shut-off valveService and procurementBusinesses with multiple drum sizes or container types often coordinate their order with the appropriate foot-operated or mini version, so that the right pump is to hand for every container. If you have any questions regarding the correct thread size, the choice between hand- and foot-operated models, or spare parts such as the shut-off valve, we will be happy to assist you directly, even for larger requirements across multiple workstations.
Heidolph Hei-PLATE Mix'n'Heat Core+ magnetic stirrer, Ø135 mm, Pt1000 connection, 506-22100-00
If you need a slightly smaller hotplate for a reflux setup with a compact flask or for a space-saving multi-unit arrangement, the Hei-PLATE Mix’n’Heat Core+ in the 135-millimetre version offers the same digital functionality as the 145-millimetre variant, but with a more compact Kera-Disk footprint. The LCD display, dynamic rotary controls and the optional external Pt1000 sensor are identical; it heats up to 300 °C at up to 1,400 revolutions per minute.Same technology, smaller footprintApart from the diameter of the base, this model is technically no different from the 145-millimetre version: the same housing with external dimensions of 168 x 101 x 299 millimetres, the same EC motor with a speed range of 100 to 1,400 revolutions per minute, and the same heating power of 800 watts at 230 volts (EU). Anyone wishing to set up several stirring stations side by side, or who works predominantly with smaller flasks and vessels, will benefit from the slightly smaller diameter of the 135-millimetre Kera-Disk, without compromising on speed or heating power.Two heating modes for different requirementsThe FAST heating mode brings the sample up to temperature quickly, whilst PRECISE then takes over for fine control without overshoot; both modes operate via the optional external Pt1000 sensor with an accuracy of ± 0.2 Kelvin and a resolution of 1 Kelvin. A lock function on the two dynamic rotary controls prevents accidental adjustment whilst tests are in progress; a visual residual heat warning lights up on the base when the temperature reaches 50 °C.Typical applicationsReflux set-ups with the Findenser Mini and a compact flaskSpace-saving multiple set-ups in smaller laboratories or fume hoodsSyntheses with a defined heating ramp using the FAST and PRECISE modesTraining laboratories with limited floor spaceExpansion of existing Core+ workstations with a second, more compact unitLoad capacity and protection ratingWeighing around 3 kilograms, the base can still carry batches of up to 25 kilograms. IP42 protection rating protects against foreign bodies larger than 1 mm and dripping water falling at an angle; the sound pressure level remains below 50 dB(A). The patented Kera-Disk coating made of anodised aluminium is chemical-resistant and scratch-resistant, regardless of the selected diameter.Selection guide: 135 or 145 millimetresIf a larger work surface is required for larger flasks or additional accessories, the Hei-PLATE Mix’n’Heat Core+ (Ø145) is the closer fit. Equipped directly with a Pt1000 sensor, the basic unit is available in the Hei-PLATE Sensor Basic Core+ package; for a complete reflux setup with the Findenser Mini, it is available in the Hei-PLATE Reflux Core+ Mini package. For those who do not require digital temperature measurement, the Hei-PLATE Mix'n'Heat Core offers analogue control.Technical detailsDimensions (W x H x D)168 x 101 x 299 mmFootprint (Kera-Disk)Ø 135 mm, anodised aluminiumWeightapprox. 3 kgMaximum permissible load25 kgDriveEC motor, counter-clockwise rotationSpeed range100 to 1,400 rpmHeating power800 W at 230 V (EU), 600 W at 115 V (US)Heating temperature range20 to 300 °CHeating controlPIDTemperature measurement accuracy± 0.2 K, plus Pt1000 toleranceTemperature measurement resolution1 KDisplayLCD displayDisplay/measurement range15 to 325 °C (with Pt1000 temperature sensor)Degree of protection (EN 60529)IP42Sound pressure level< 50 dB(A)Rated voltage230 V, 50/60 Hz (EU); 115 V, 50/60 Hz (US)Connection typeL+N+PEProtection classIOvervoltage categoryIIPollution degree2Power consumption825 W (EU) / 625 W (US) in normal operation, 1.7 W on standbyEMC classB, Group 1Operating temperature5 to 31 °C at up to 80 % relative humidity, 32 to 40 °C at up to 50 % relative humidity (linearly decreasing)Installation altitudeup to 2,000 m above sea levelScope of deliveryHei-PLATE Mix'n'Heat Core+ (135 mm), order number 506-22100-00The external Pt1000 temperature sensor is not included in the scope of delivery for this item number and is ordered separately or as part of a sensor pack.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Heidolph Scientific Products GmbH, is DE 50705753. Information on the return of old appliances can be found on our Environment and Disposal page.Warranty and procurement serviceHeidolph Scientific Products GmbH, Schwabach, provides a 3-year manufacturer’s warranty against defects in materials and workmanship. This excludes glass and wear parts, damage caused during transport, and damage resulting from improper use. If the device is registered with Heidolph, the warranty begins on the date of purchase; otherwise, it begins on the date of manufacture as indicated by the serial number. Your statutory warranty rights remain unaffected. For this model in the Hei-PLATE series, Heidolph offers a 10-year warranty provided the instrument is registered with Heidolph within the first year of purchase. Our procurement service puts together the suitable Pt1000 probe and accessories for compact reflux set-ups.
Bandelin SONOREX SUPER RK 156 BH ultrasonic bath with heating, 9 L, 35 kHz, 646
Long pipettes, tubing, tools or torches rarely fit into a square tank. The Bandelin SONOREX SUPER RK 156 BH, with internal dimensions of 500 x 140 x 150 mm, is deliberately designed to be narrow and long, thus providing a total capacity of 9.0 l for elongated items that cannot be accommodated in the more compact SUPER RK models.Narrow tank for elongated objectsWhilst most SUPER RK models have approximately square tanks, the RK 156 BH, measuring 500 mm in length and just 140 mm in width, is tailored to slender items: shorter laboratory glass rods, tools, hoses or several smaller instruments placed side by side. The working capacity is 6.0 l, and four vibration systems ensure uniform ultrasonic agitation across the entire length of the tank.600-watt heater for thorough cleaningAt an operating frequency of 35 kHz, the RK 156 BH delivers 860 watts of peak power and 215 watts of rated power; the SweepTec function prevents standing waves across the elongated tank shape. The 600-watt heater covers a range of 30 to 80 °C and is fitted with dry-run protection; the timer ranges from 1 to 15 minutes (± 5 %) or continuous operation, controlled via rotary knobs for time and temperature.Ball valve drain and robust constructionA G 1/4 ball valve on the right-hand side allows the tank to be drained in a controlled manner. The tank and housing are made of 1.4301 stainless steel with a thickness of 1.0 mm; the external dimensions of 530 x 165 x 300 mm and the net weight of 7.3 kg correspond to the narrow, elongated design. The housing is IP 32-rated, and the 2-metre power cable is permanently attached to the unit.When the BH design is suitableFor compact, roughly cube-shaped items to be cleaned, the standard SUPER RK models, such as the RK 510 H (9.7 l, but with a more square tank), are often the more practical choice. The RK 156 BH is worth considering where the length of the items to be cleaned is the main issue, such as with rods, longer tools or multiple objects that need to be placed side by side rather than on top of one another.Product range breakdown: SUPER RK, DIGITEC DT and smart STThe slim BH design is currently only available within the SUPER RK series with classic rotary knob controls. Those looking instead for digital button controls with an LED display will find them in the DIGITEC DT series, whilst the smart ST series features touchscreen controls with programme memory. We also offer Elma Elmasonic ultrasonic baths, although these are built with different tank shapes.Use and maintenanceThe working capacity of 6.0 l is less than the total capacity of 9.0 l, ensuring that no water spills over the rim when the items to be cleaned are placed inside. A concentrate from Bandelin’s TICKOPUR range is suitable as the cleaning agent. Freshly prepared liquid should be run briefly in continuous operation before the first cleaning cycle, so that dissolved air escapes and cavitation can take full effect. After use, the tank can be drained completely via the ball valve, leaving no residue, and then wiped dry.Typical applicationsCleaning of elongated tools, rods and hosesSimultaneous cleaning of several smaller instruments side by sidePre-cleaning of narrow laboratory glassware prior to further processingDegreasing of elongated metal parts in workshops and industryFrequently asked questionsWhy is the tank so narrow and long?The internal dimensions of 500 x 140 x 150 mm are specifically designed for elongated items that do not fit into more square-shaped tanks.Where is the drain?On the right, as a ball valve with a G 1/4 connection.Is the RK 156 BH heated?Yes, with a heating power of 600 watts and a temperature range of 30 to 80 °C.How many vibration systems does the unit have?Four, distributed along the entire length of the tank to ensure uniform agitation.Technical detailsTotal capacity / Working capacity9.0 l / 6.0 lInternal tank dimensions (L x W x D)500 x 140 x 150 mmExternal dimensions (L x W x H)530 x 165 x 300 mmWeight (net)7.3 kgUltrasonic frequency35 kHzUltrasonic powerPeak power 860 W, rated power 215 W, 4 vibration systemsHeating power600 W, temperature range 30 to 80 °C, dry-run protectionTimer1 to 15 minutes (± 5 %) or continuous operationOperationRotary knobFunctionsSweepTec, pulse functionTank materialStainless steel 1.4301, thickness 1.0 mmHousing materialStainless steel 1.4301DrainBall valve G 1/4, right-hand sideMains connection230 V~ (± 10 %), 50/60 Hz, optionally 115 V~, 2 m fixed mains lead, protection class ICurrent consumption230 V 3.6 A / 115 V 7.1 ADegree of protectionIP 32Medical device classClass I (Regulation (EU) 2017/745)ConformityLow Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EUPackaging dimensions655 x 265 x 370 mmScope of delivery1x Bandelin SONOREX SUPER RK 156 BH ultrasonic bath with heaterFixed mains lead (2 m)Instructions for useThe insert basket and lid are not included in the scope of delivery and are available separately.Individual requirements and procurement serviceFor the K 6 BL insert basket, the D 156 lid or another tank shape from the SUPER RK series, individual procurement requirements apply. You can request a quote without obligation via our procurement service for suitable accessories, a replacement basket or another model from the SONOREX range.


