Brands
Laboratory equipment and lab supplies from brand manufacturers
LT Laborhandel is a specialist retailer for laboratory equipment, liquid handling, consumables and protective equipment. We offer selected brand manufacturers, source genuine products directly from the manufacturer as a rule, and pass on the full manufacturer's warranty. For every range, we advise on choosing the right equipment, for example when volume and viscosity determine the right stirrer or temperature range and control accuracy determine the right chamber.
We are an IKA premium partner and have worked with Memmert, Binder and Kern & Sohn for years.
The logo takes you to the manufacturer page with the brand's range, for IKA also with accessories and spare parts for your device.
You will find every article from our manufacturers here; use the filters on the left to narrow down by brand and properties. If a product is missing, we will ask the manufacturer for you.
Meditrade Nitril Black Examination Gloves, black (100 pcs.), M, 1284M
Black nitrile gloves are widely used in the tattoo and beauty industries, as the dark colour gives a professional appearance and any ink or pigment residue is not immediately noticeable. Meditrade Nitril Black examination gloves are powder-free, latex-free, disposable nitrile gloves with a micro-textured, elastic and tear-resistant surface, available in sizes S, M, L and XL, each in packs of 100. Latex-free for sensitive skin The gloves are completely latex-free and are therefore a suitable choice for staff with a diagnosed type 1 latex allergy, regardless of the area of application. The force at break is 6 N, tested to an AQL value of 1.5, the standard sampling inspection level for the leak-tightness of disposable gloves. Thickness varies by zone The Nitril Black gloves feature varying thicknesses across different zones: the thickness on the palm is 0.07 mm (± 0.02 mm), on the fingertips 0.10 mm (± 0.02 mm) for added grip on the fingertips, and 0.05 mm (± 0.02 mm) at the cuff for easier donning. This variation in thickness is common in nitrile gloves, as the fingertips are subject to the highest mechanical stress, whilst the wrist primarily requires elasticity. Nitrile as the material of choice Nitrile is a synthetic rubber which, unlike natural latex, does not contain the allergy-triggering latex proteins, whilst offering greater puncture and chemical resistance than latex. For businesses that avoid natural latex entirely for hygiene or compliance reasons, nitrile is therefore the obvious alternative to traditional latex gloves. Furthermore, nitrile retains its shape well even after prolonged wear, which noticeably enhances comfort throughout the entire shift in professions where gloves are changed frequently throughout the day. Tested according to EN 455 and EN ISO 374 Nitril Black complies with EN 455 (Parts 1 to 4) for medical disposable gloves, as well as the test standards of the EN ISO 374 series (Parts 1, 2, 4 and 5) for protective gloves against microorganisms and chemicals. In addition, the data sheet lists EN 16523-1 for determining resistance to chemical permeation. The manufacturer also classifies them as food-safe, which is relevant, for example, for inspection tasks in food processing or the catering industry. EN 16523-1 specifies how long it takes and to what extent a chemical penetrates the glove material, providing an additional indicator alongside the pure microorganism barrier as defined by EN ISO 374. Selection guide: choosing the right size The size range starts at S and goes through M and L to XL; there is no XS size for this model. We can provide width and length measurements on request; when selecting a size, we also recommend comparing it with the size of a disposable glove you already own that fits well. SizeManufacturer’s item no.EAN S1284S4250016405078 M1284M4250016405085 L1284L4250016405092 XL1284XL4250016405108 Differentiation within the nitrile range Several other Meditrade nitrile gloves with the same thickness gradation on the palm, fingertips and cuff are available alongside the Nitril Black. For those looking for a light-coloured glove for food processing rather than the dark contrasting colour, the Meditrade Nitril 3000 in white offers an alternative with identical wall thickness and additionally documented carton and pallet dimensions. For businesses using colour-coding by station or shift, the Meditrade Nitril Viola in purple is also available. Anyone requiring a variant tested against blood-borne pathogens with a wider size range up to XXL will find this in the Meditrade Nitril NextGen. Use and disposal We can provide details of storage conditions and shelf life on request. According to the manufacturer, the glove is non-sterile and intended for single use; it can be worn on either hand. After use, disposable gloves are usually disposed of as commercial waste; contaminated gloves are disposed of separately, depending on internal hazardous substances regulations. Typical applications The black colour of these nitrile gloves makes them suitable for a variety of sectors and applications: Tattoo and beauty salons, where black is an established, professional-looking colour Catering and event venues, to ensure a uniform, smart appearance for staff Laboratory and examination work, where light-coloured powders, tablets or crystals are more visible on dark gloves than on light-coloured ones General examination and routine tasks where a latex-free, food-safe disposable glove is required For example, when portioning powders or granules in the laboratory, it is immediately apparent whether any residue has become trapped on the dark glove, a contrast that a natural-coloured glove does not provide. Assessing your needs correctly: the pack of 100 for everyday use Nitril Black is sold in packs of 100 per size. A simple rough calculation can help with demand planning: at a rate of 10 gloves per workstation per day, one pack covers around two working weeks; at 30 gloves per day, it lasts for three to four working days. For businesses with higher consumption of several sizes simultaneously, it is advisable to stock several packs of the relevant sizes straight away, so that no workstation runs out of a particular size. The AQL value of 1.5 indicates the maximum number of defective gloves per batch that are tolerated within the framework of statistical sampling; a lower value indicates a stricter inspection. If you stock several sizes at the same time, you can distinguish between the packs of 100 at a glance using the manufacturer’s item number, without having to open the individual packs first. Frequently asked questions about Nitril Black Is Nitril Black latex-free?Yes, the glove is made entirely from nitrile and is therefore latex-free. Is Nitril Black sterile?No, according to the manufacturer, it is a non-sterile, single-use glove. How thick is the glove?The thickness is 0.07 mm on the palm, 0.10 mm at the fingertips and 0.05 mm at the cuff, each with a tolerance of ± 0.02 mm. What sizes are available?S, M, L and XL. There is no XS size for this model. Is the glove food-safe?Yes, the manufacturer classifies it as food-safe. What is the medical device class and PPE category of the glove?According to the data sheet, the glove is a class I medical device (Regulation (EU) 2017/745) and category III PPE (Regulation (EU) 2016/425). Technical details MaterialNitrile ColourBlack SurfaceMicro-textured, elastic, tear-resistant Thickness (palm)0.07 mm ± 0.02 mm Thickness at fingertips0.10 mm ± 0.02 mm Cuff thickness0.05 mm ± 0.02 mm Force at break6 N AQL1.5 PropertiesPowder-free, latex-free, food-safe, non-sterile, ambidextrous StandardsEN 455-1/-2/-3/-4, EN ISO 374-1/-2/-4/-5, EN 16523-1 Scope of delivery 1 pack = 100 Meditrade Nitril Black examination gloves (size as per variant selection) Individual requirements and procurement service Do you require larger quantities or a different colour from the Meditrade nitrile range? Our procurement service will be happy to support you with the suitable selection.
Meditrade Nitril NextGen Examination Gloves, blue, 100 pcs., size L, 1283L
Some applications require more than the basic protection typically offered by nitrile gloves, for example where, in addition to protection against contamination, the penetration of blood-borne pathogens must also be reliably prevented. Meditrade Nitril NextGen examination gloves are available in six sizes from XS to XXL and are additionally tested to ASTM F 1671. Powder-free, latex-free and available in blue, each pack containing 100 gloves. Latex-free and tested against blood-borne pathogens According to the manufacturer, the NextGen is produced without natural rubber latex and is therefore suitable for organisations that consistently rely on latex-free personal protective equipment. Beyond the series of standards customary for nitrile gloves, EN 455 and EN ISO 374, it is also tested according to ASTM F 1671 for the penetration of blood-borne pathogens, supplemented by EN 16523 for chemical permeation and DIN EN ISO 374-5 for protection against microorganisms. This additional testing distinguishes the NextGen from the simpler nitrile variants in the range. Thickness at the palm, shaft and fingertips According to the data sheet, the thickness at the palm is 0.07 mm (± 0.02 mm), at the fingertips 0.10 mm (± 0.02 mm) and on the shaft also 0.07 mm (± 0.02 mm), ensuring that the cuff area remains mechanically robust, rather than being thinner as is the case with some other nitrile gloves. The median force at break is at least 6.0 N both before and after artificial ageing, tested with an AQL value of 1.5. ASTM F 1671: what the additional test entails ASTM F 1671 tests whether a glove material can withstand the penetration of a bacteriophage, used as a model organism for blood-borne pathogens, under defined pressure. For workplaces with an increased risk of exposure, such as in emergency care or during invasive procedures, such an additional test is an indication of a higher level of protection than that offered by a nitrile glove which has only undergone the basic standards EN 455 and EN ISO 374. Combined with the permeation test according to EN 16523, NextGen thus covers both the microbiological and chemical aspects of the barrier performance. Six sizes from XS to XXL With its XXL size, the NextGen also accommodates particularly large hands. The width ranges from 75 mm (± 5 mm) for XS, through 95 mm (± 10 mm) for M, to at least 115 mm for XXL; the length is at least 240 mm for all sizes. SizeManufacturer’s item no.WidthLength XS1283XS75 mm (± 5 mm)min. 240 mm S1283S80 mm (± 10 mm)min. 240 mm M1283M95 mm (± 10 mm)min. 240 mm L1283L110 mm (± 10 mm)min. 240 mm XL1283XL≥ 110 mmmin. 240 mm XXL1283XXL≥ 115 mmmin. 240 mm Distinction within the nitrile range We offer the NextGen alongside several nitrile gloves in different colours from the same Meditrade range. Whilst the Meditrade Nitril 3000 in white, the Meditrade Nitril Black in black and the Meditrade Nitril Viola in purple all share the same basic formulation with a thickness of 0.07/0.10/0.05 mm, the NextGen is additionally tested to ASTM F 1671 against blood-borne pathogens and is available in size XXL. Those who also require a longer cuff for forearm protection will find this in the Meditrade Nitril X-Long, with a cuff length of 295 mm. Use, storage, shelf life and disposal According to the data sheet, the shelf life is 3 or 5 years, provided the gloves are stored in a cool, dry place and protected from direct sunlight. The gloves are non-sterile, ambidextrous and intended for single use only. According to the data sheet, they contain dithiocarbamates, which should not be used by anyone with a known hypersensitivity to these substances. After use, the gloves are disposed of as commercial waste or via the organisation’s internal hazardous waste disposal system, depending on the level of contamination. Typical applications The additional testing for blood-borne pathogens and the wide range of sizes make the NextGen an obvious choice for: Examination and care activities with increased requirements for barrier protection against pathogens Organisations that operate strictly latex-free whilst needing to cater for large hand sizes up to XXL Laboratory work involving contact with chemicals for which EN 16523 is documented as the permeation test Food processing, for which the glove is suitable according to the data sheet Teams with widely varying hand sizes who wish to maintain a single order list for all staff For example, in an outpatient clinic or laboratory with a changing workforce, the same type of glove can be stocked for almost every hand size without having to switch to a different product range for particularly large hands. Assessing requirements correctly: from the pack to the carton NextGen is sold in packs of 100 per size. According to the manufacturer, one carton holds 10 packs, i.e. 1,000 gloves, with a pallet containing 72 cartons (carton dimensions 295 x 260 x 250 mm). A simple rough calculation helps with demand planning: at a consumption rate of 10 gloves per workstation per day, one pack covers around two working weeks; at 30 gloves per day, it lasts for three to four working days. Where there are several workstations with different hand sizes, including XXL, it is advisable to stock each size separately, as experience shows that demand for XXL is lower, but if stock runs out, it is more difficult to reorder at short notice than the more common medium sizes. Setting a fixed minimum stock level for each size in your own stock management system helps to ensure that even sizes ordered less frequently, such as XS or XXL, are reordered in good time. Frequently asked questions about Nitril NextGen What distinguishes NextGen from other nitrile gloves in the range?It is additionally tested according to ASTM F 1671 for resistance to the penetration of blood-borne pathogens and is also available in size XXL. Is the NextGen latex-free?Yes, according to the manufacturer, it is produced without natural rubber latex. How thick is the glove?The thickness is 0.07 mm on the palm and shaft, and 0.10 mm at the fingertips, with a tolerance of ± 0.02 mm in each case. Is the glove sterile?No, according to the data sheet, the NextGen is a non-sterile, single-use glove. What sizes are available?XS, S, M, L, XL and XXL, each with its own width specification as per the data sheet. Can I order individual gloves instead of the whole pack?No, the smallest order unit is a pack of 100 gloves per size. What does the additional ASTM F-1671 test mean in practice?It documents that, in laboratory tests, the glove material withstands the penetration of a model organism for blood-borne pathogens under pressure, in addition to the basic standards EN 455 and EN ISO 374. Technical details MaterialNitrile butadiene rubber (NBR) ColourBlue SurfaceMicro-textured, rolled cuff, suitable for both hands Lengthmin. 240 mm Thickness (palm)0.07 mm ± 0.02 mm Fingertip thickness0.10 mm ± 0.02 mm Thickness of shaft0.07 mm ± 0.02 mm Median force at break (before/after ageing)min. 6.0 N AQL1.5 Packaging100 pieces per pack, 10 packs per carton (1,000 pieces), 72 cartons per pallet FeaturesPowder-free, latex-free, non-sterile, ambidextrous, suitable for food contact Medical device classI (Regulation (EU) 2017/745) PPE categoryIII (Regulation (EU) 2016/425) Shelf life3 or 5 years; store in a cool, dry place; protect from direct sunlight StandardsEN 455-1/-2/-3/-4, EN ISO 374-1/-2/-4/-5, EN ISO 21420:2020, EN 16523, ASTM F 1671, EN ISO 13485:2016 Scope of delivery 1 pack = 100 Meditrade Nitril NextGen examination gloves (size as per variant selection) Individual requirements and procurement service Do you require a different size, a different colour from the Meditrade nitrile range, or larger purchase quantities for your business? Our procurement service will be happy to support you with the suitable selection.
Meditrade Nitril 3000 Examination Gloves, white (box of 100), L, 1280L
You don’t always need specialist equipment for your daily use of nitrile gloves. Meditrade Nitril 3000 examination gloves are the standard white nitrile gloves in the Meditrade range available from us; they are powder-free, latex-free and come with fully documented packaging and pallet dimensions for logistics planning. Available in sizes S to XL, each in packs of 100. Latex-free with a tried-and-tested basic formulation The glove is made from nitrile butadiene rubber (NBR) containing the following ingredients: antioxidant, sulphur, zinc oxide, zinc diethyldithiocarbamate, zinc dibutyl dithiocarbamate, titanium dioxide and potassium hydroxide; it is free from mercaptobenzothiazole and thiurams and, according to the manufacturer, is not manufactured using natural rubber latex. The textured surface with a rolled cuff ensures a secure grip and makes the gloves easier to put on and take off. Thickness from the cuff to the fingertips According to the data sheet, the thickness at the shaft is 0.05 mm (± 0.02 mm), at the palm 0.07 mm (± 0.02 mm) and at the fingertip 0.10 mm (± 0.02 mm), ensuring that the greatest mechanical stress is absorbed at the fingertips. The force at break is at least 6 N both before and after artificial ageing, tested with an AQL value of 1.5. White as a neutral base colour Unlike the coloured variants of the Meditrade nitrile range, Nitril 3000 is available in a neutral white colour, which is regarded as the standard colour for examination gloves in many organisations and is compatible with almost any corporate design or hygiene concept. For organisations with no specific need for colour-coding or additional testing, it is therefore often the obvious first choice before a more specialised variant, such as a contrasting colour or an additionally tested version, is considered. Class I medical device and Category III PPE The Nitril 3000 is classified as a Class I medical device in accordance with Regulation (EU) 2017/745 and as Category III personal protective equipment in accordance with Regulation (EU) 2016/425. It complies with EN 455 (Parts 1 to 4), EN ISO 374-1, -2, -4 and -5, EN 16523-1 for chemical permeation, EN ISO 21420:2020, and is manufactured under a quality management system certified according to EN ISO 13485:2016. According to the data sheet, it is also suitable for contact with food. Selection guide: choosing the right size In our range, the Nitril 3000 is available in sizes S to XL, with widths ranging from 80 mm (± 10 mm) for size S to over 110 mm for size XL. SizeManufacturer’s item no.WidthLength S1280S80 mm (± 10 mm)min. 240 mm M1280M95 mm (± 10 mm)min. 240 mm L1280L110 mm (± 10 mm)min. 240 mm XL1280XL> 110 mmmin. 240 mm Distinctions within the nitrile range Within our Meditrade nitrile range, the Nitril 3000 is the standard white version with fully documented packaging and pallet dimensions. Anyone looking for the same glove in a dark contrasting colour for tattooing, cosmetic or laboratory work involving light-coloured powders will find the Meditrade Nitril Black, which offers the same range of thicknesses. For businesses using colour-coding, the Meditrade Nitril Viola in purple is also available. If you require a variant that has been additionally tested against blood-borne pathogens and is available in sizes up to XXL, you will find this in the Meditrade Nitril NextGen. Use, storage, shelf life and disposal According to the data sheet, the shelf life is 3 or 5 years, provided the gloves are stored in a cool, dry place and protected from direct sunlight. The gloves are non-sterile, ambidextrous and intended for single use. According to the information in the data sheet, they contain dithiocarbamates, which should not be used by anyone with a known hypersensitivity to these substances. After use, the gloves are disposed of as commercial waste or via the internal hazardous waste disposal system, depending on the degree of contamination. Typical applications As the basic variant of the nitrile range, the Nitril 3000 is suitable for a wide range of applications: General examination and routine tasks in medical practices, laboratories and care settings Food processing and catering, for which the glove is suitable according to the data sheet Businesses that require a light-coloured, neutral glove without the need for additional testing Logistics-intensive businesses that can plan precisely thanks to documented carton and pallet dimensions For example, during incoming goods inspection in food processing, the same type of glove can be used consistently, from sampling right through to packaging checks. A neutral, widely used basic variant is also practical in training and educational contexts, as it is not tied to a specific workstation or colour-coding scheme. Assessing requirements correctly: from the pack to the carton The Nitril 3000 is sold in packs of 100 pieces per size. According to the manufacturer, one carton holds 10 packs, i.e. 1,000 gloves, with a pallet containing 72 cartons (carton dimensions 29.5 x 26.0 x 25.0 cm). A simple rough calculation helps with demand planning: at a consumption rate of 10 gloves per workstation per day, one pack covers around two working weeks; at 30 gloves per day, it lasts for three to four working days. For larger businesses with multiple workstations, the carton dimensions can also be used to plan storage logistics directly, for example, how many cartons will fit on a pallet or on a warehouse shelf. This makes capacity planning easier, particularly for larger businesses with their own warehousing, without having to first request the dimensions separately from the manufacturer. Why a basic version can be a sensible choice Not every business requires the additional ASTM F-1671 testing offered by NextGen or colour-coding by workstation. Where the nitrile glove is primarily intended to provide reliable basic protection according to EN 455 and EN ISO 374, with traceable logistics, the Nitril 3000 is an economically obvious choice without compromising on force at break, AQL value or certification compared to the other variants in the range. Frequently asked questions about the Nitril 3000 Is the Nitril 3000 latex-free?Yes, according to the manufacturer, it is produced without natural rubber latex. Is the glove sterile?No, according to the data sheet, the Nitril 3000 is a non-sterile, single-use glove. How thick is the glove?According to the data sheet, 0.05 mm on the shaft, 0.07 mm on the palm and 0.10 mm at the fingertips, with a tolerance of ± 0.02 mm in each case. How big is a carton and how many fit on a pallet?A carton holds 1,000 gloves (10 packs of 100 each) and measures 29.5 x 26.0 x 25.0 cm; a pallet holds 72 cartons. Are the gloves suitable for food contact?Yes, according to the data sheet, they are suitable for contact with food. Can I order individual gloves instead of the whole pack?No, the pack of 100 pieces per size is the smallest unit sold. How does the Nitril 3000 differ from the coloured variants in the range?It shares the same material and thickness grades as Nitril Black and Nitril Viola, but is the only variant in neutral white without an additional colour-coding function. Technical details MaterialNitrile butadiene rubber (NBR) ColourWhite SurfaceTextured, rolled cuff, suitable for both hands Lengthmin. 240 mm Thickness (palm)0.07 mm ± 0.02 mm Fingertip thickness0.10 mm ± 0.02 mm Thickness of shaft0.05 mm ± 0.02 mm Force at break (before/after ageing)min. 6 N AQL1.5 Packaging100 pieces per pack, 10 packs per carton (1,000 pieces), 72 cartons per pallet FeaturesPowder-free, latex-free, non-sterile, ambidextrous, suitable for food contact Medical device classI (Regulation (EU) 2017/745) PPE categoryIII (Regulation (EU) 2016/425) Shelf life3 or 5 years; store in a cool, dry place; protect from direct sunlight StandardsEN 455-1/-2/-3/-4, EN ISO 374-1/-2/-4/-5, EN 16523-1, EN ISO 21420:2020, EN ISO 13485:2016 Scope of delivery 1 pack = 100 Meditrade Nitril 3000 examination gloves (size as per variant selection) Individual requirements and procurement service Do you require larger purchase quantities, a different colour from the Meditrade nitrile range, or assistance with warehouse logistics? Our procurement service will be happy to support you with the suitable selection.
Meditrade Gentle Skin Grip, latex examination gloves, powder-free, 100 pieces - M, 1221GRIP-M
Wet instruments, oily tools or slippery packaging put many disposable gloves to the test: as soon as the surface becomes damp or greasy, the grip decreases noticeably. According to the manufacturer, Meditrade Gentle Skin Grip latex examination gloves are the grippiest latex gloves in the Meditrade range. An acrylic polymer coating on a textured surface provides extra grip where smooth gloves reach their limits. Available in sizes XS to XL, each in packs of 100. Acrylic polymer coating for extra grip In addition to the ingredients typically found in latex gloves, natural rubber latex, sulphur, zinc oxide, zinc diethyldithiocarbamate, zinc dibutyl dithiocarbamate, titanium dioxide and antioxidants, the Grip range also features an acrylic polymer coating on the textured surface. This coating is the key difference compared to traditional latex gloves without any special grip optimisation and, according to the manufacturer, improves grip, particularly when handling damp, oily or powdery surfaces. The glove is free from mercaptobenzothiazole and thiurams. Thickness from the cuff to the fingertips According to the manufacturer’s data sheet, the thickness at the cuff is at least 0.08 mm, at the palm at least 0.11 mm and at the fingertips at least 0.12 mm, ensuring that the greatest material thickness is available at the point subject to the most stress. The breaking force is at least 6 N both before and after artificial ageing, tested with an AQL value of 1.5 for the absence of holes in the batch. The rolled cuff also makes it easier to put on and take off the gloves, even when the hands themselves are already damp. Class I medical device and PPE Category III The glove complies with EN 455 (Parts 1 to 4) for single-use medical gloves, as well as EN ISO 374-1, -2, -4 and -5 for protection against microorganisms, supplemented by EN 16523-1 for chemical permeation and EN 420:2003+A1:2009 as the general standard for protective gloves. It is classified as a Class I medical device in accordance with Regulation (EU) 2017/745 and as Category III personal protective equipment under Regulation (EU) 2016/425, and is manufactured under a quality management system certified according to EN ISO 13485:2016. Why smooth gloves reach their limits in wet conditions A purely textured glove without an additional coating loses some of its grip when it comes into contact with water, oil or cleaning agents, because a thin film of liquid forms between the glove and the workpiece. This is precisely where the acrylic polymer coating of the Gentle Skin Grip comes into its own: according to the manufacturer, it increases friction even in damp conditions without compromising the elasticity of the natural latex. For standard dry tasks without any particular risk of slipping, however, a simpler latex glove from our range is often sufficient. Selection guide: choosing the right size As with the other Gentle Skin gloves, the size range from XS to XL is based on the width of the hand, measured at the widest point excluding the thumb. SizeManufacturer’s item no.WidthLength XS1221GRIP-XS< 80 mmmin. 240 mm S1221GRIP-S80 mm (± 10 mm)min. 240 mm M1221GRIP-M95 mm (± 10 mm)min. 240 mm L1221GRIP-L110 mm (± 10 mm)min. 240 mm XL1221GRIP-XL> 110 mmmin. 240 mm Distinction within the Gentle-Skin latex range Within the Meditrade latex range, the Grip differs from the other two variants primarily due to its coating. Those who, on the other hand, require a particularly fine sense of touch for pipetting and laboratory work are better served by the low-protein Meditrade Gentle Skin Sensitive. For general routine use without any specific grip or protein requirements, the Meditrade Gentle Skin compact+ is available, with a comparable basic wall thickness. All three are tested according to EN 455 and EN ISO 374 and are classified as a Class I medical device and PPE Category III. Those wishing to avoid natural latex entirely will find latex-free alternatives in our range of nitrile gloves, although these do not feature the grip coating described here. Use, storage, shelf life and disposal According to the data sheet, the shelf life is 3 or 5 years, provided the gloves are stored in a cool, dry place and protected from direct sunlight. The gloves are non-sterile, ambidextrous and intended for single use only. As the gloves are made from natural rubber latex, the manufacturer expressly warns of the risk of allergic or even anaphylactic reactions. After use, the gloves are disposed of as commercial waste or via the internal hazardous waste disposal system, depending on the level of contamination. Typical applications The grippy coating makes the Gentle Skin Grip of interest wherever moisture or grease would otherwise make a firm grip difficult: Cleaning and processing of laboratory glassware and instruments, often in contact with water or cleaning agents Handling oily or greasy components in workshops and industry Packaging and order-picking tasks involving frequent changes of material Examination and care tasks where a secure grip on damp surfaces is required For example, when rinsing and sorting laboratory glassware under running water, the grip is maintained, whereas an uncoated glove would slip more easily in the same situation. The difference compared to a smooth glove surface is also clearly evident when handling greasy seals or lubricants in the workshop. Assessing your requirements correctly: from the pack to the carton Gentle Skin Grip is sold in packs of 100 per size; according to the manufacturer’s data sheet, a carton contains 10 packs, i.e. 1,000 gloves. A simple rough calculation can help with demand planning: at a rate of 10 gloves per workstation per day, one pack covers around two working weeks; at 30 gloves per day, it lasts for three to four working days. Businesses with multiple workstations or frequent glove usage should ideally stock several packs of the appropriate size to ensure that no workstation runs out of a particular size. Frequently asked questions about Gentle Skin Grip What sets the Grip apart from other latex gloves?The textured surface is additionally coated with an acrylic polymer, which, according to the manufacturer, improves grip on damp or oily surfaces. Is the glove sterile?No, according to the data sheet, it is a non-sterile, single-use glove. How thick is the glove?The thickness is at least 0.08 mm on the cuff, 0.11 mm on the palm and 0.12 mm at the fingertips. Is the Grip suitable for people with a latex allergy?No, the glove is made of natural rubber latex and, according to the manufacturer, may trigger allergic or even anaphylactic reactions. What is the shelf life of the glove?According to the data sheet, 3 or 5 years when stored in a cool, dry place, protected from direct sunlight. Is the Grip coating also available on a latex-free glove?For this data sheet, the coating is only documented for the latex version. For a latex-free alternative offering comparable grip performance, our procurement service will be happy to assist you with your selection. What sizes are available?XS, S, M, L and XL, each with its own width specification as per the data sheet, ranging from under 80 mm to over 110 mm. Can I order individual gloves instead of the whole pack?No, the product is sold exclusively in packs of 100 per size. Technical details MaterialNatural rubber latex with an acrylic polymer coating SurfaceTextured, rolled cuff, ambidextrous Lengthmin. 240 mm Cuff thicknessmin. 0.08 mm Palm thicknessmin. 0.11 mm Fingertip thicknessmin. 0.12 mm Force at break (before/after ageing)min. 6 N AQL1.5 Packaging100 pieces per pack, 10 packs per carton (1,000 pieces) CharacteristicsPowder-free, non-sterile, textured, rolled cuff, ambidextrous, free from mercaptobenzothiazole and thiurams Medical device classI (Regulation (EU) 2017/745) PPE categoryIII (Regulation (EU) 2016/425) Shelf life3 or 5 years; store in a cool, dry place; protect from direct sunlight StandardsEN 455-1/-2/-3/-4, EN ISO 374-1/-2/-4/-5, EN 16523-1, EN 420:2003+A1:2009, EN ISO 13485:2016 Scope of delivery 1 pack = 100 Meditrade Gentle Skin Grip latex examination gloves (size as per variant selection) Individual requirements and procurement service Do you require a different size, a latex-free alternative with similar grip, or larger purchase quantities for your business? Our procurement service will be happy to assist you in making the right choice.
Meditrade Gentle Skin Sensitive Latex Gloves, natural colour, powder-free, 100 pieces, size M, 1221RMT
Anyone who spends many hours in a laboratory or in a care setting pipetting, decanting samples or handling delicate instruments will quickly realise whether a glove is helpful or more of a hindrance. Meditrade Gentle Skin Sensitive latex gloves are low-protein natural latex gloves designed specifically for this kind of fine motor work: powder-free, thin-walled and with a stretch that moulds closely to the hand without causing fatigue even when worn for hours on end. Available in sizes XS to XL, each pack containing 100 gloves. Low-protein thanks to a multi-stage processing method Natural latex naturally contains water-soluble proteins which can trigger skin reactions in sensitised individuals. The Sensitive range is therefore processed using a multi-stage washing process and additionally undergoes double chlorination, which reduces the protein content whilst also allowing the gloves to be put on easily without powder. This does not make the glove completely latex-free; it remains a natural rubber product containing natural rubber latex, sulphur, dithiocarbamate, zinc oxide, titanium dioxide, potassium hydroxide, calcium carbonate, polyacrylate and colour pigments. If you have a known Type 1 latex allergy, a nitrile glove from our range is therefore the safer choice. Gradual thickness variation from the palm to the fingertips According to the manufacturer’s data sheet, the thickness at the palm is at least 0.11 mm, and at the fingertips 0.13 mm (± 0.02 mm), slightly thicker to provide additional tactile sensitivity and mechanical strength precisely where the greatest stress occurs during gripping and pipetting. The force at break is at least 6 N both before and after artificial ageing, tested with an AQL value of 1.5 for the absence of holes in the batch. The textured, micro-roughened surface with a rolled cuff also ensures a secure grip, whether used dry or in contact with aqueous solutions. Class I medical device and PPE Category III The glove complies with EN 455 (Parts 1 to 4) for single-use medical gloves, as well as EN ISO 374-1, -2, -4 and -5 for protection against microorganisms, supplemented by EN 16523-1 for chemical permeation and EN ISO 21420:2020 as the basic standard for protective gloves in general. It is classified as a Class I medical device under Regulation (EU) 2017/745 and as Category III personal protective equipment under Regulation (EU) 2016/425, and is manufactured under a quality management system certified according to EN ISO 13485:2016. According to the data sheet, it is also suitable for contact with food, which is relevant, for example, for sample preparation in food analysis. Latex or nitrile: when it’s worth switching Natural latex offers high elasticity with low mechanical stress, which means the Gentle Skin Sensitive fits snugly to the hand and provides a particularly fine sense of touch. However, natural latex is less suitable for tasks involving non-polar solvents such as oils or fats, as the material can swell. In such cases, or where there is a known latex allergy, a nitrile glove from our range is the more appropriate choice, offering a comparable fit but greater chemical resistance. Selection guide: choosing the right size The size range extends from XS to XL and is based on the width of the hand, measured at the widest point excluding the thumb. A glove that is too tight causes the hand to tire more quickly when worn for long periods, whilst a glove that is too loose reduces both tactile sensitivity and a secure grip. SizeManufacturer’s item no.WidthLength XS1221RXST< 80 mmmin. 240 mm S1221RST80 mm (± 10 mm)min. 240 mm M1221RMT95 mm (± 10 mm)min. 240 mm L1221RLT110 mm (± 10 mm)min. 240 mm XL1221RXLT> 110 mmmin. 240 mm Differentiation within the Gentle Skin latex range Two other latex gloves from the same Meditrade range are available alongside the Gentle Skin Sensitive. Anyone who, in addition to a fine sense of touch, requires greater grip on damp or oily surfaces will find this in the textured Meditrade Gentle Skin Grip with its acrylic polymer coating. For day-to-day routine use without the protein-reduced processing of the Sensitive range, the Meditrade Gentle Skin compact+, with a comparable wall thickness, is an obvious alternative from the same product family. All three share the same basic construction made from natural latex with a rolled cuff and testing according to EN 455 and EN ISO 374-1, but differ in wall thickness, surface treatment and protein content. Those who wish to avoid natural latex altogether will find a latex-free alternative in our range of nitrile gloves. Use, storage, shelf life and disposal According to the manufacturer, the gloves are suitable for all areas where there is a risk of contamination, ranging from highly infectious situations in hospitals and doctors’ surgeries, through the care sector and laboratories, to the pharmaceutical industry, cleaning and industrial applications. According to the data sheet, the shelf life is 3 or 5 years, provided they are stored in a cool, dry place and protected from direct sunlight. The gloves are non-sterile and intended for single use only; used gloves are disposed of as commercial waste or via the internal hazardous waste disposal system, depending on the level of contamination. It is recommended that the gloves be changed at the latest upon the first visible sign of damage or soiling, even if the specified shelf life of 3 or 5 years has not yet been reached. Typical applications The low-protein formulation makes the Gentle Skin Sensitive particularly interesting where tactile sensitivity and skin compatibility have to come together: Sample preparation and pipetting tasks in the laboratory where dexterity is required Care and examination tasks involving frequent glove changes throughout a shift Food analysis and quality control, where the glove is suitable for food contact according to the data sheet Cleaning and routine tasks in the pharmaceutical industry and industrial settings For example, when pipetting a series of samples over several hours, the thin-walled material on the palm and fingertips can be utilised without the hand tiring prematurely, an advantage over thicker standard gloves. Assessing requirements correctly: from the pack to the carton Gentle Skin Sensitive is sold in packs of 100 per size. According to the manufacturer’s specifications, one carton contains 10 packs, i.e. 1,000 gloves, with a pallet comprising 56 cartons. A simple rough calculation can help with demand planning: at a rate of 10 gloves per workstation per day, a pack of 100 will last for around two working weeks; at 30 gloves per day, it will last for three to four working days. For businesses with multiple workstations or varying sizes, it is advisable to stock several packs of the appropriate size straight away, to ensure that no workstation runs out of a particular size. Frequently asked questions about Gentle Skin Sensitive Is the Gentle Skin Sensitive suitable for people with a latex allergy?No. The glove is low in protein but is still made from natural rubber latex. For those with a known Type 1 latex allergy, we recommend a nitrile glove from our range. Are the gloves sterile?No; according to the data sheet, they are non-sterile, single-use gloves. How thick is the glove on the palm and fingertips?The thickness is at least 0.11 mm on the palm and 0.13 mm (± 0.02 mm) on the fingertips. Is the glove suitable for contact with food?Yes, according to the data sheet, it is suitable for contact with food. What is the shelf life of the glove?3 or 5 years according to the data sheet, provided it is stored in a cool, dry place and protected from direct sunlight. Can I order individual gloves instead of the whole pack?No, the sales unit is a pack of 100 per size. Technical details MaterialNatural latex ColourNatural white SurfaceTextured, chlorinated, rolled cuff Lengthmin. 240 mm Thickness (palm)min. 0.11 mm Fingertip thickness0.13 mm ± 0.02 mm Force at break (before/after ageing)min. 6 N AQL1.5 Packaging100 pieces per pack, 10 packs per carton (1,000 pieces), 56 cartons per pallet FeaturesPowder-free, non-sterile, textured, rolled cuff, ambidextrous, suitable for food contact Medical device classI (Regulation (EU) 2017/745) PPE categoryIII (Regulation (EU) 2016/425) Shelf life3 or 5 years; store in a cool, dry place; protect from direct sunlight StandardsEN 455-1/-2/-3/-4, EN ISO 374-1/-2/-4/-5, EN 16523-1, EN ISO 21420:2020, EN ISO 13485:2016 Scope of delivery 1 pack = 100 Meditrade Gentle Skin Sensitive latex gloves (size as per variant selection) Individual requirements and procurement service Do you require a different size, a sterile version or larger purchase quantities for your laboratory or practice? Our procurement service will be happy to support you with the suitable selection.
Meditrade Gentle Skin compact+ latex gloves, powder-free, 100 pcs., XS, 1221XSI
Where natural rubber latex is not an issue, its elasticity and comfort make it the first choice amongst disposable gloves for many users. Meditrade Gentle Skin compact+ latex gloves are powder-free, natural white, online-chlorinated for easy donning and doffing, and available in packs of 100 in sizes XS to XL. Natural rubber latex for high elasticity The glove is made from natural rubber latex with a textured surface and a rolled cuff. The online chlorination process reduces the material’s natural stickiness, making the glove easier to put on and take off than an untreated latex variant, even with slightly damp hands. The high inherent elasticity of natural rubber ensures a snug, second-skin fit, which many users prefer to nitrile for tasks requiring fine motor skills, as the glove adapts more directly to the shape of the hand. Thickness for delicate tasks According to the data sheet, the median thickness at the palm and fingertips is at least 0.11 mm in each case, with a median length of at least 240 mm. The width varies according to size: under 80 mm for XS, 80 mm (± 10 mm) for S, 95 mm (± 10 mm) for M, 110 mm (± 10 mm) for L and over 110 mm for XL. The force at break is at least 6 N (median), both before and after artificial ageing, tested with an AQL value of 1.5. Class I medical device and Category III PPE The Gentle Skin compact+ is classified as a Class I medical device in accordance with Regulation (EU) 2017/745 and as Category III personal protective equipment in accordance with Regulation (EU) 2016/425. It complies with EN 455 (Parts 1 to 4), EN ISO 374-1/-2/-4/-5 and EN ISO 21420:2020, and is manufactured under a quality management system certified according to EN ISO 13485:2016. Important note for those with a latex allergy As a natural rubber product, the glove contains dithiocarbamates (ZDC, ZDBC) according to the data sheet, for which there is a warning regarding possible allergic reactions. However, it is free from mercaptobenzothiazole and thiurams, two other common contact allergens used in rubber processing. Organisations with staff or customers known to have a latex allergy should switch to a nitrile-based alternative. Compact pack of 100 as a sales unit Unlike some nitrile variants in the range, which are sold in large cartons containing several thousand pieces, the price of Gentle Skin compact+ applies per handy pack of 100. It is ordered by the carton, at least 10 packs (1,000 pieces), then in steps of 10. Typical applications As a powder-free, highly elastic latex examination glove, the Gentle Skin compact+ is suitable for, amongst other things: Examination and care activities requiring a high degree of tactile sensitivity and dexterity Medical practices and clinics where there are no known cases of latex allergy amongst staff or patients Routine laboratory work where the high elasticity of natural rubber latex is preferred over nitrile Short-term tasks involving frequent glove changes, thanks to the compact pack of 100 For example, during examinations requiring fine motor skills, such as palpating small structures, the snug fit of natural rubber latex can be put to targeted use, whilst the compact pack size ensures that a fresh pack is always to hand, even for less frequent tasks, rather than having to keep a large carton in stock. In training situations too, where groups of trainees rotate, the 100-pack makes it easier to track consumption per group than with a large carton. Packaging: from individual pack to carton Gentle Skin compact+ is sold in packs of 100 pieces per size. According to the manufacturer, one carton holds 10 packs (1,000 pieces), with a pallet containing 54 cartons. The individual pack measures 120 x 215 x 70 mm, whilst the carton measures 245 x 360 x 225 mm, dimensions that aid storage planning in first-aid cupboards or stock rooms. Anyone looking for a powder-free latex alternative with a different grip surface will find it in the Gentle Skin Grip from the same product range. The entire latex range can be found under ‘Latex gloves’. Technical details MaterialNatural rubber latex ColourNatural white SurfaceTextured, rolled cuff, ambidextrous, online chlorinated PowderingPowder-free Lengthmin. 240 mm (median) Width by sizeXS < 80 mm, S 80 ± 10 mm, M 95 ± 10 mm, L 110 ± 10 mm, XL > 110 mm Thickness (palm/fingertip)min. 0.11 mm (median) Force at break (before/after ageing)min. 6 N (median) AQL1.5 Packaging100 pieces per pack (120 x 215 x 70 mm), 10 packs per carton (245 x 360 x 225 mm), 54 cartons per pallet Medical device classClass I (Regulation (EU) 2017/745) PPE categoryIII (Regulation (EU) 2016/425) StandardsEN 455-1/-2/-3/-4, EN ISO 374-1/-2/-4/-5, EN ISO 21420:2020, EN ISO 13485:2016 Scope of delivery 1 pack = 100 Meditrade Gentle Skin compact+ latex gloves (size as per variant selection). Can only be ordered by the carton: at least 10 packs (1 carton), then in steps of 10. Individual requirements and procurement service Do you require larger purchase quantities, a different variant from the Gentle Skin range, or advice on latex tolerance within your team? Our procurement service will be happy to support you with the suitable selection.
Duran laboratory bottle, clear, graduated, GL 45, without screw cap and pouring ring, 3,500 ml
The DURAN Original graduated laboratory bottle is a narrow-neck bottle with a GL thread according to DIN 168-1, made from clear borosilicate glass 3.3. The thread type depends on the volume: GL 25 for 10 and 25 ml, GL 32 for 50 ml, and GL 45 for 100 ml and above. We offer the bottle in sizes ranging from 10 ml to 20 l, with or without a cap, as well as the 25-litre bottle with a cap. Matching screw caps are available for all three thread sizes.Glass and standardsThe glass complies with Type I according to USP <660>, EP 3.2.1 and JP <7.01> and meets ASTM E438 Type I Class A. The bottles are manufactured according to ISO 4796-1:2016, with the exception of the 10 ml bottle and the 25 ml bottle without a cap. An application has been submitted for the 25-ml bottle without a cap to be included in the standard. Each bottle bears a Retrace Code. This allows the batch to be traced; the certificate is available for download at cert.dwk.com.Closure and pouring ringThe version with a cap comes with a blue screw cap made of PP and a non-drip pouring ring made of PP; both are suitable for use up to 140 °C. All components are autoclavable at 121 °C or 134 °C. The version without a closure consists solely of the glass bottle.Graduation and volumeThe scale is fired on as a white print, with a labelling field for the contents next to it. The graduations serve as a guide when filling. The nominal volume is less than the brim-full volume: for the 100 ml bottle, the brim-full volume is 138 ml.Typical applicationsLong-term storage of solutions, buffers and reagents in glassSterilisation of media in autoclaves (version with cap, 121 °C or 134 °C)Storage where Type I glass according to USP, EP or JP is requiredDrip-free pouring via the pouring ring (version with cap)Documented work with batch traceability via the Retrace CodeVariants and MPNsThe table shows all sizes with dimensions and order numbers. Up to 2,000 ml, a pack contains 10 bottles; from 3,500 ml upwards, it contains one bottle.VolumeThreadØ (mm)Height with cap (mm)MPN with capHeight without cap (mm)MPN without capPack size (pieces)10 mlGL 253359218010851552180108021025 mlGL 253674218011453702180114041050 mlGL 3246912180117538721801170410100 mlGL 455610521801245810021801240910150 mlGL 456211521801295511021801290610250 mlGL 457014321801365113821801360210500 mlGL 458618121801445917621801440110750 mlGL 4595208218015155203218015106101 lGL 45101230218015455225218015406102 lGL 45136265218016357260218016308103.5 lGL 4516030021801695729521801690815 lGL 45182335218017353330218017304110 lGL 45227415218018658410218018609115 lGL 45268450218018855445218018806120 lGL 45288510218019157505218019108125 lGL 45316545218019251--1Technical detailsMaterialBorosilicate glass 3.3, clearGlass typeType I according to USP <660>, EP 3.2.1, JP <7.01>; ASTM E438 Type I Class AThreadDIN 168-1, GL 25 (10 and 25 ml), GL 32 (50 ml), GL 45 (from 100 ml)Volume10 ml to 25 lGraduationfired-on white print with a labelling fieldClosure (version with)Blue PP screw cap, PP pouring ring, up to 140 °CAutoclavable121 °C or 134 °C, all componentsStandardISO 4796-1:2016, except for 10 ml and 25 ml without closureTraceabilityRetrace Code on every bottleScope of deliveryWith cap: bottle, blue PP screw cap and PP pouring ringWithout cap: glass bottlePackaging unit 10 pieces up to 2,000 ml, 1 piece from 3,500 mlMatching productsFor preparation and mixing, we offer the DURAN Erlenmeyer flask and the DURAN beaker, low form.Individual requirements and procurement serviceWe can obtain other sizes, caps for the bottle without a cap, or larger quantities on request. Please contact us via the procurement service.
WTW SenTix 41 pH Electrode with Temperature Sensor, Gel Electrolyte, DIN Connector, 103635
Measuring pH in wastewater, aquariums or swimming pools should not depend on a refilling routine. The WTW SenTix 41 features a plastic shaft and a gel electrolyte which, according to WTW, is not refilled. The electrode is low-maintenance. The pH measuring range extends from 0 to 14, and it can be used at sample temperatures of 0 to 80 °C.Gel electrolyte and fibre junctionThe shaft is made of PPE/PS, is 120 mm long and has a diameter of 12 mm. The membrane is cylindrical; its resistance at 25 °C is less than 1 GΩ. According to WTW, the fibre junction prevents blockages. There is no need to monitor or top up the electrolyte level. If the electrolyte is meant to be refillable, the SenTix 51 and 52 with liquid electrolyte and a ceramic junction in a plastic shaft are the alternative.Connection and temperature measurementThe SenTix 41 has a permanently attached 1 m cable with a waterproof DIN plug (DIN 19262). An NTC temperature sensor (30 kΩ) is built in and measures the sample temperature; it is connected to the 4 mm banana plug. The gel electrodes in this range differ in plug, cable length and temperature sensor. You should therefore establish which input the measuring instrument has before placing your order.Typical applications according to WTWWhen taking samples from water bodies, at the edge of a pool or from a wastewater pipe, what counts is an electrode that is quickly ready for use. WTW names the following media for this series:Electroplating effluent, industrial wastewater and wastewater in generalAquarium and swimming pool waterGroundwater, lake water, surface water and seawaterHousehold cleanersStorage and careBefore the first measurement, remove the wetting cap; gas bubbles behind the membrane can be removed by shaking. For short measurement breaks, immerse the electrode in reference electrolyte (3 mol/l KCl, Ag+-free). Overnight and for longer periods, it stays in the wetting cap, filled with the same electrolyte. According to WTW, storing the electrode dry or in deionised water can cause permanent damage. If the cap has dried out, the electrode needs at least 24 hours in reference electrolyte. As with any pH electrode, strong acids and alkalis, hydrofluoric acid, organic solvents, oils, fats and proteins shorten its service life.Technical detailsTypepH electrode, analogue, gel electrolyteShaft materialPlastic (PPE/PS)Shaft length / Shaft diameter120 mm / 12 mmElectrolyteGel, non-refillableReference systemSilver/silver chlorideJunctionFibreMembrane shapeCylindricalpH measuring range0 to 14Temperature range0 to 80 °CMembrane resistance< 1 GΩ at 25 °CTemperature sensorNTC 30 kΩConnectionDIN plug (DIN 19262), waterproof, and 4 mm banana plugCable1 m fixed cableScope of delivery1 WTW SenTix 41 pH electrode with wetting cap1 m fixed cable with DIN and banana plugs, permanently attached to the electrodeAccessories and procurement serviceReference electrolyte KCl 3 mol/l for the wetting cap and buffer solutions for calibration are also available. Enquiries regarding other SenTix models or larger quantities go through our procurement service.
Bandelin SONOREX SUPER RK 31 Ultrasonic Bath, 0.9 L, 35 kHz, 329
Sensor tips, small cannulas, jewellery or individual cuvettes do not require a large bath for ultrasonic cleaning; rather, they need a bath that delivers uniform cavitation to every corner of the tank. With a total capacity of 0.9 l, the Bandelin SONOREX SUPER RK 31 is the smallest model in the SUPER RK series and is designed specifically for these small-item cleaning tasks in laboratories, medical practices and workshops.Small tank, noticeable cavitationAt an operating frequency of 35 kHz, the RK 31 generates a peak ultrasonic power of 160 watts at a nominal ultrasonic power of 40 watts, distributed across a single vibration system. This is sufficient for the small tank volume of 0.9 l (working capacity 0.6 l); larger SUPER RK models, such as the RK 514 BH, on the other hand, operate with four vibration systems covering a significantly larger area. The automatic SweepTec function continuously adjusts the frequency slightly, thereby preventing standing waves in the ultrasonic field; as a result, the cleaning effect remains uniform even in small volumes.Thin stainless steel tank for the laboratory benchThe oscillating tank is made of 1.4301 stainless steel with a thickness of 0.8 millimetres; the housing is made from the same material. The internal dimensions of 190 x 85 x 60 mm and the compact external dimensions of 205 x 100 x 180 mm ensure that the unit, with a net weight of 2.2 kg, can still be accommodated even on already occupied work surfaces. The RK 31 is operated via a robust rotary handle; the timer ranges from 1 to 15 minutes (tolerance ± 5 %), and continuous operation is also available.No drain, no heating, but simpleThis model has no drain; a ball valve is not provided for this size. With a capacity of 0.9 l, the tank can be emptied directly over the edge after the cleaning cycle; an additional connection would be rather cumbersome in this case. Similarly, the RK 31 does not feature a heating element. Anyone requiring heating for cleaning in the same size should choose the RK 31 H with a fixed 65 °C; the next larger model with adjustable heating is the RK 100 H.Selection guide for the SUPER RK seriesThe SUPER RK series from Bandelin covers a wide range: from the RK 31 with a 0.9-litre capacity to the RK 1050 with a total capacity of 58 l. If you are only cleaning individual small parts, sensor tips or cuvettes, you are properly equipped with the RK 31. If the batch size increases to include several instruments or small glass vessels, it is worth considering the RK 100 H (3.0 l, heated) or the RK 103 H (4.0 l, heated and with a drain). For entire sieves or beakers, the larger models from the RK 510 (9.7 l) upwards are the more suitable choice.SUPER RK, DIGITEC DT and smart ST comparedIn addition to the SUPER RK series with classic rotary knob control, Bandelin offers the DIGITEC DT series with push-button control, an LED display and DEGAS degassing, as well as the smart ST series with a touchscreen, finely adjustable power control and programme memory. Those who only clean occasionally and value straightforward, robust operation would be well advised to choose a SUPER RK model such as the RK 31. We also offer Elma Elmasonic ultrasonic baths, an alternative for laboratories already equipped with this brand.Use and maintenanceThe working capacity of 0.6 l is deliberately set below the total capacity of 0.9 l, as space must be left for the items being cleaned when filling the bath; otherwise, the liquid will spill over the rim. As for the cleaning solution itself, Bandelin offers its own TICKOPUR range of concentrates; for the SONOREX PR series of pipette cleaners, this is included in the set, whilst a suitable concentrate for the RK 31 must be purchased separately. Freshly prepared cleaning fluid contains dissolved air, which initially dampens cavitation; a short pre-run in continuous operation before the actual cleaning process dispels it. The stainless steel tank is compatible with most aqueous cleaning agents; however, abrasive sponges or chlorine-based agents should still be avoided. At the end of the working day, it is best to empty and dry the tank.Typical applicationsCleaning of small sensor tips, cannulas and needlesPrecision cleaning of jewellery and small metal partsPre-cleaning of precision mechanical components and watch movementsCleaning individual cuvettes or small sample vessels in the laboratoryFrequently asked questionsIs the SONOREX SUPER RK 31 heated?No, the RK 31 is unheated. The heated version with the same volume is the RK 31 H (fixed at 65 °C); the next larger model with adjustable heating is the RK 100 H.Does the unit have a drain?No, the RK 31 has no ball valve; with a capacity of 0.9 l, the bath is emptied directly.Is the RK 31 a medical device?Yes, it is classified as a Class I medical device according to Regulation (EU) 2017/745 and is also CE-compliant with the Low Voltage, EMC and RoHS Directives.Are the basket and lid included in the scope of delivery?No, the K 08 insert basket and the D 08 lid are available separately as accessories.Technical detailsTotal capacity / Working capacity0.9 l / 0.6 lInternal dimensions of tank (L x W x D)190 x 85 x 60 mmExternal dimensions (L x W x H)205 x 100 x 180 mmWeight (net)2.2 kgUltrasonic frequency35 kHzUltrasonic powerPeak ultrasonic power 160 W, nominal ultrasonic power 40 W, 1 vibration systemTimer1 to 15 minutes (± 5 %) or continuous operationOperationRotary knobFunctionsSweepTec, pulse functionTank materialStainless steel 1.4301, thickness 0.8 mmHousing materialStainless steel 1.4301DrainNo drain/ball valveMains connection230 V~ (± 10 %), 50/60 Hz, optionally 115 V~, 2 m fixed mains lead, protection class ICurrent consumption230 V 0.2 A / 115 V 0.4 AProtection ratingIP 32Medical device classClass I (Regulation (EU) 2017/745)ConformityLow Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU, RoHS Directive 2011/65/EUPackaging dimensions320 x 235 x 205 mmScope of delivery1x Bandelin SONOREX SUPER RK 31 ultrasonic bathFixed mains lead (2 m)Instructions for useThe insert basket and lid are not included in the scope of delivery and are available separately.Individual requirements and procurement serviceFor the K 08 insert basket, the D 08 lid or a larger SUPER RK model, there is an individual procurement requirement. You can use our procurement service to request a quote for suitable accessories, a replacement basket or another model from the SONOREX range.
Macherey-Nagel NANOCOLOR COD 160 tube test, 985026
Chemical oxygen demand (COD) is one of the most important parameters for the assessment of industrial and municipal effluents. The NANOCOLOR COD 160 tube test from Macherey-Nagel delivers precise, time-saving results based on DIN ISO 15705 when used in conjunction with the appropriate NANOCOLOR photometers. Low measurement range for samples with low organic load The test covers a measurement range of 15–160 mg/L O₂ and is therefore suitable for samples with a lower organic load than the NANOCOLOR COD 4000 (Item No. 985011). The method is based on the potassium dichromate procedure and is based on DIN ISO 15705 H45, EPA 410.4, APHA 5220 D and DIN 38409 H41-1. Compatible with standard NANOCOLOR photometers The test can be analysed on the following instruments: 500 D, Advance, MT Easy UV, MT Easy VIS, PF-3 COD, PF-12Plus, UV/VIS II and VIS II, including the NANOCOLOR VIS II (item no. 919650.1) and NANOCOLOR Advance (item no. 919750) spectrophotometers already offered in our range. Scope of application The test is designed for wastewater, sewage sludge and water samples. A sturdy box containing 20 round cuvettes is sufficient for 20 determinations. When stored at 15–25 °C, the shelf life is 1 year from the date of manufacture. Technical details Parameters COD Method COD - Potassium dichromate Measuring range COD - 15–160 mg/L O₂ Note Measurement range on the NANOCOLOR VIS II Test range Low Test method Photometric Underlying standard Based on DIN ISO 15705 H45, analogous to EPA 410.4, APHA 5220 D, DIN 38409 H41-1 Test No. 0-26 Platform NANOCOLOR tube tests Compatible with 500 D, Advance, MT Easy UV, MT Easy VIS, PF-3 COD, PF-12Plus, UV/VIS II, VIS II Application Wastewater, sewage sludge, water Seawater analysis No Digestion kit No Sewage sludge digestion No NanOx Metal No NanOx N No Packaging unit 20 test(s) Scope of delivery Sturdy box containing 20 round cuvettes. Sufficient for 20 determinations. Shelf life (from date of manufacture) 1 year(s) Storage temperature 15–25 °C Gross weight (including packaging) 376 g Packaging dimensions 160 x 111 x 122 mm Hazardous substances Yes Trademarks NANOCOLOR
KNF LABOPORT N 96, very compact, chemical-resistant diaphragm vacuum pump with manual speed control, 322806
For those who have limited space on their lab bench but still need a reliable, chemical-resistant vacuum source, the KNF LABOPORT N 96 is a highly compact, oil-free diaphragm vacuum pump. Weighing just 1.3 kg and measuring 75 x 119 x 156 mm, it fits next to almost any workstation and can be precisely adjusted to the specific application via the manual speed control, for example for filtration, liquid aspiration or solid-phase extraction (SPE). Very compact and lightweight Measuring just 75 x 119 x 156 mm (W x H x D) and weighing 1.3 kg, the N 96 is the most compact pump in the LABOPORT range. Its small footprint makes it a practical addition to workstations where there is no room for larger vacuum pumps, such as directly next to a filtration unit or an SPE setup. Chemical-resistant materials, tailored to the design The pump head is made of PPS (polyphenylene sulphide), the diaphragm is PTFE-coated, and the valves are made of FKM. This combination of materials differs from that of the larger LABOPORT-N pumps (which feature a TFM PTFE pump head and FFPM valves), but is designed specifically for the compact design of the N 96 and its intended applications. Manual, stepless speed control The N 96’s flow rate can be continuously adjusted to suit the specific application via the manual speed control. According to the manufacturer, this ensures exceptional ease of use in day-to-day laboratory work and enables precise vacuum control, for example when gently filtering sensitive samples. Up to 2.5 bar operating pressure, not just vacuum In addition to a maximum ultimate vacuum of 130 mbar (abs.), the N 96 also achieves an operating pressure of up to 2.5 bar (rel.). This means it can be used not only for evacuation but also, where required, for pumping under slight overpressure, a difference from the larger LABOPORT-N pumps, which are primarily designed for vacuum operation. Mains-powered via an external plug-in power supply The pump itself operates at 24 V DC and is powered via an external plug-in power supply with a wide-range input (100 to 240 V AC, 50/60 Hz); it does not have a built-in battery. The power consumption is 19 W; the pump’s operating current is 0.9 A, whilst that of the power supply unit is 0.4 A (230 V AC) or 0.7 A (100 V AC). The degree of protection is IP40. Permissible media and ambient temperatures range from +5 to +40 °C. Maintenance-free and 100 % oil-free According to the manufacturer, the N 96 operates maintenance-free and is 100 % oil-free. There is no need for regular oil changes, and there is no risk of oil mist entering the gases being pumped or the laboratory air, an advantage wherever contamination-free conditions are required, such as during sample preparation for analysis. Gas connection and accessories The gas connection is a 1/8 NPT fitting; the supplied hose connector has an internal diameter of 6 mm and is made of PP. A column mounting bracket is available for wall mounting if required, along with a spare parts kit and a power supply set for replacement purposes. Suitable for confined spaces As the N 96 is powered by an external plug-in power supply, the pump housing itself remains particularly compact, an advantage wherever shelves, fume hoods or workstations are already densely occupied. The column mount also allows for space-saving installation away from the worktop, for example on a stand or a wall within easy reach of the workstation. Typical applications Filtration Liquid aspiration Solid-phase extraction (SPE) For example, the N 96 can be placed right next to an SPE cartridge stand, where it provides the necessary vacuum for sample purification in a space-saving manner, without the need for a separate, bulky pump setup. Need a higher flow rate? The larger LABOPORT series If the flow rate of 7 l/min is insufficient for a larger application, or if there is an additional need to collect liquids and condensate or to recover solvents, there are also the larger LABOPORT series: the pure diaphragm vacuum pump N 820 G / N 840 G (20 and 34 l/min respectively), the SR 820 G / SR 840 G vacuum pump system with two separator bottles, and the SH 820 G / SH 840 G vacuum pump system with a separator and high-performance condenser for solvent recovery. Technical details Flow rate (max.)7 l/min (0.4 m³/h) Ultimate vacuum (max.)130 mbar (abs.) Operating pressure (max.)2.5 bar (rel.) Pump headPPS (polyphenylene sulphide) DiaphragmPTFE-coated ValvesFKM Pump voltage24 V DC Power supply voltage100 to 240 V AC, 50/60 Hz (plug-in power supply, wide-range input) Power P119 W Operating current, pump0.9 A Operating current of power supply unit0.4 A (230 V AC) / 0.7 A (100 V AC) Degree of protectionIP40 Permissible medium/ambient temperature+5 to +40 °C Dimensions (W x H x D)75 x 119 x 156 mm Weight1.3 kg Gas connectionNPT 1/8, hose connection ID 6, PP Scope of delivery 1x KNF LABOPORT N 96 diaphragm vacuum pump External plug-in power supply (wide-range input) Silencer Hose connection ID 6, PP Individual requirements and procurement service A spare parts kit, a power supply set and a column mounting bracket for wall mounting are among the accessories available for the N 96. If you have any questions regarding suitable accessories, spare parts or individual requirements relating to your KNF LABOPORT N 96, our procurement service will be happy to assist you.
Macherey-Nagel folded filter paper MN 615, qualitative, medium-speed (Ø 55–600 mm), 185 mm
Efficiency in the laboratory: Macherey-Nagel MN 615 folded filter papers Macherey-Nagel MN 615 folded filter papers are the time-saving solution for daily laboratory routines. Unlike simple filter paper circles, which have to be laboriously folded by hand (quarter-fold) before being placed in the funnel, these filters are already machine-folded (1/4-fold). This not only saves valuable working time but also offers a decisive technical advantage: the pleated structure significantly increases the effective filter surface area. The result is a faster flow rate and a reduced tendency to clog, as the precipitate is distributed more evenly. The all-rounder for qualitative analyses The MN 615 grade is a widely used standard paper for qualitative analyses (ash content approx. 0.1 %), which primarily involve the clarification of solutions or the recovery of filtrates. Medium-speed filtration: With a filtration time of approx. 22 seconds (according to DIN 53137), this paper offers a balance between speed and retention. Smooth surface: The fibres are processed to form a homogeneous structure that reliably retains particles. Retention range: Particles ranging from 4 to 12 µm (e.g. lead sulphide, calcium oxalate) are filtered. Sizes from 55 to 600 mm We offer the MN 615 folded filter papers in a wide range of diameters: from 55 mm for small analytical funnels up to 600 mm for large-scale production batches. Please note that the diameter specified always refers to the diameter of the unfolded paper disc. Areas of application General chemistry: Clarification of salt solutions and buffers. Food analysis: Filtration of macerates, juices or extracts. Schools & Education: Time-saving preparation of school experiments. Environmental analysis: Pre-filtration of water samples. Technical data Grade: MN 615 (folded filter paper) Type: Qualitative filter paper Filtration speed: Medium-speed (approx. 22 s) Surface: Smooth Grammage: 70 g/m² Thickness: 0.16 mm Retention range: 4 – 12 µm Ash content: approx. 0.1 % Material: Cellulose (approx. 95 % alpha-cellulose) Format: folded into quarters (ready for the funnel) Packaging unit: 100 pieces per pack Scope of delivery 1 x pack of 100 Macherey-Nagel folded filter papers (grade MN 615) (The diameter corresponds to the variant you selected above.) Individual requirements & accessories Do you have the right funnel for your folded filter papers? Rule of thumb: The top edge of the folded filter paper should end approx. 1–2 cm below the rim of the funnel. A filter that is too large will protrude (risk of evaporation, tendency to creep), whilst one that is too small will not make full use of the funnel’s volume. Alternatives: If you need to filter very fine precipitates (e.g. barium sulphate), we recommend the denser grade MN 619. For very coarse, bulky precipitates, opt for grade MN 617. Do you require large quantities for industrial use or special sizes? Please contact our procurement service.
Memmert UN30 universal oven, compact heating and drying oven with natural convection, 32 litres, up to 300 °C
The Memmert UN30 universal oven is the most compact model in the Memmert universal oven range and operates using purely natural convection rather than an active air turbine. With an internal volume of 32 litres, a temperature range of 20 to 300 °C and a unit weight of around 45 kg, it fits on a laboratory bench, where space is usually more limited than in the equipment area of a permanent laboratory. As there is no active air circulation inside the chamber, the UN30 is particularly suitable for applications where vibration-free and low-dust operation are more important than the shortest possible heating time, such as when gently drying light samples or fine powders.Natural convection for vibration-free, low-dust operationUnlike the UF models in the series, the Memmert UN30 universal oven deliberately does not feature an air turbine or a recirculation motor. Heat rises within the chamber purely by convection, without a fan setting air, dust or light sample components in motion. As a result, the operating temperature range starts from at least 5 °C above room temperature up to 300 °C, whilst the forced-air models in the UF series only start from 10 °C above room temperature; however, thanks to forced air circulation, they heat up more quickly and distribute the temperature more actively. For samples that are sensitive to air movement, such as loose powders, fine fibres or specimens that must not be blown away by draughts, the UN30’s natural convection is suitable. A DIN Class A Pt100 temperature sensor with 4-wire measurement ensures the same setting accuracy as in the larger models, despite the simpler airflow principle: 0.1 °C to 99.9 °C and 0.5 °C from 100 °C.ControlCOCKPIT SingleDISPLAY: compact operation with a full range of functionsDespite its compact design, the UN30 does not compromise on any of the control functions found in the larger models. The ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a TFT colour graphic display, regulates temperature in Celsius or Fahrenheit, as well as the position of the exhaust air damper, programme duration, time zone and summer/winter time. As no air turbine is fitted, the only parameter omitted is that for the recirculation fan speed. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWAIT function only starts the process time once the setpoint temperature has been reached. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download, whilst a USB stick containing the full version is available as an optional accessory.Compact dimensions of the Memmert UN30 universal ovenThe internal dimensions are 400 x 320 x 250 mm, whilst the external dimensions are 585 x 704 x 434 mm. One electropolished stainless steel grid shelf is included as standard; the cabinet can accommodate up to three shelves in total. The maximum load capacity is 60 kg for the entire unit and 20 kg per shelf, which is entirely sufficient for smaller sample batches and individual containers. As with the larger models, the interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The fully insulated stainless steel door locks via a 2-point compression door lock. The UN30 is connected to a 230 V or 115 V supply, in each case at 50/60 Hz, with a power consumption of around 1,600 W.Selection guide: choosing the right size from the UN seriesThe Memmert universal oven series with natural convection covers a range of internal volumes from 32 to 749 litres. The UN30 is the smallest model in the range. When choosing the right size, the key factors, apart from internal volume, are the footprint and the number of shelves required; not every larger model takes up more floor space than the next smaller one.ModelInternal volumeUN3032 l, footprint 585 x 434 mm, max. 3 shelvesUN5553 l, footprint 585 x 514 mm, max. 4 shelvesUN7574 l, footprint 585 x 514 mm, max. 6 shelvesUN110108 l, footprint 745 x 584 mm, max. 5 shelvesUN260256 l, footprint 824 x 684 mm, max. 9 shelvesUN450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUN750749 l, footprint 1,224 x 784 mm, max. 14 shelvesThe UN30 is suitable when space on the laboratory bench is limited and only a few samples are being processed at a time. If the number of samples increases, the Memmert UN55 universal oven is the obvious next size up, offering 53 litres instead of 32 and 4 shelves instead of 3, whilst taking up only slightly more floor space. All seven sizes in the series can be found in our range of climate chambers and incubators.Distinction: TwinDISPLAY and the forced-air versionWithin the UN30 series, the most important purchasing decision is between SingleDISPLAY and TwinDISPLAY. The UN30 described here operates with a single Pt100 sensor and one display; for unattended processes with higher safety requirements, the Memmert UN30plus universal oven offers two redundant Pt100 sensors as well as two TFT displays instead of one. Those who would instead prefer to benefit from the shorter heating-up time offered by active air circulation and do not require vibration-free operation will find the Memmert UF30 universal oven to be the equivalent model featuring forced air circulation rather than natural convection, whilst retaining the same internal volume of 32 litres.Safety according to DIN 12880, even in the smallest modelThe UN30 also features adjustable electronic temperature monitoring plus a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature reaches approximately 20 °C above the maximum cabinet temperature. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. CE and EAC markings, as well as a UL test mark, are present.Application, installation and disposalThe same installation rules apply to the Memmert UN30 universal oven when placed on a laboratory bench as for the larger models in the series: a minimum clearance of 15 cm from the wall, a minimum clearance of 20 cm from the ceiling, and a minimum clearance of 5 cm on each side from a wall or adjacent unit. It may be installed at altitudes of up to 2,000 m above sea level at ambient temperatures of 5 °C to 40 °C and a maximum relative humidity of 80 %, non-condensing. Electrically, the UN30 is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The interior, made of easy-to-clean stainless steel, can be cleaned using standard laboratory cleaning products. As an electrical appliance, the UN30 is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste; see Regulatory information below.Typical applicationsThe compact Memmert UN30 universal oven is suitable wherever space is limited or where vibration-free, low-dust heat treatment is more important than a short heating-up time.Drying small sample quantities and laboratory glassware on the laboratory benchVibration-free drying of dust- or air-sensitive samplesTempering, ageing and baking of small material samplesRoutine tests in quality assurance, schools and trainingA compact addition or secondary unit in laboratories with limited spaceInvestment rationale: keep it compact or opt for greater safety straight awayThe UN30 is supplied with 1 electropolished stainless steel grid shelf; the cabinet is designed to accommodate up to 3 shelves. For day-to-day operation under supervision, the SingleDISPLAY of the UN30 described here is generally sufficient. If a process runs unattended overnight, the redundant sensor system of the Memmert UN30plus universal oven reduces the risk of an undetected sensor failure. For visual inspection without opening the door, a full-view glass door with 4-layer insulation up to 250 °C or 300 °C is available as an option, as are interior lighting and a stacking kit, which allows two UN30 units to be stacked on top of one another to save space. Anyone wishing to use the data logger permanently, rather than just with the time-limited trial version, should add an AtmoCONTROL software licence. For pharmaceutical or standards-compliant applications, we arrange calibration, IQ/OQ and maintenance services, including DAkkS calibration on request.Frequently asked questions before purchaseDoes the UN30 fit on a standard laboratory bench?Yes, with a net weight of around 45 kg and external dimensions of 585 x 704 x 434 mm, the UN30 is designed for use on a laboratory bench, provided that the bench can safely support the load.How many samples can fit into the UN30 at once?One grid shelf is included as standard; up to 3 shelves, each with a maximum load of 20 kg, are possible, giving a total load capacity of up to 60 kg.Is natural convection sufficient for uniform drying?For most routine applications, yes. For dust- or air-sensitive samples, the gentle natural convection of the UN30 is an advantage; for shorter heating times with larger batches, the Memmert UF30 universal oven offers active air circulation with the same volume.How does the UN30 differ from the UN30plus?Both operate using natural convection and share the same housing; the UN30plus additionally features two redundant Pt100 sensors and TwinDISPLAY for greater process reliability during unattended operation.What is the accuracy of the temperature control?0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards, as the UN30, like all models in the series, measures using a DIN Class A Pt100 sensor with 4-wire technology.Can a glass door be retrofitted?A full-view glass door with 4-layer insulation up to 250 °C or 300 °C is one of the standard options for the UN30 and can be specified when ordering.Is the UN30 suitable for continuous overnight operation?The mechanical temperature limiter, which complies with protection class 1 according to DIN 12880, switches off the heating in the event of an overtemperature of approximately 20 °C and is designed for unattended operation.Technical detailsAdjustable temperature range20 to 300 °CWorking temperature rangeat least 5 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 1,600 WShelves max.3Shelves included in scope of delivery1Max. load on unit60 kgMax. load per shelf20 kgInterior materialStainless steel, 4-sided all-round heatingCasing materialTextured stainless steel, galvanised sheet steel rear panelControl systemControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayTimer1 minute to 99 days, digital countdown timerPermissible ambient temperature5 °C to 40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation altitude2,000 mMarkingsCE, EAC, UL test markScope of delivery1x Memmert UN30 universal ovenFactory calibration certificate (calibrated at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert UN30 universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29728) or without air slots (B29729). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements & procurement serviceOptions available for the UN30 include full-view glass doors with 4-layer insulation up to 250 °C or 300 °C, interior lighting, reinforced grid shelves and perforated sheets, slide-in or floor-standing drip trays, as well as wall brackets, levelling feet, stacking kits and a mobile or fixed base frame. For data acquisition, a USB-to-Ethernet adapter with a 5 m cable, user ID sticks and AtmoCONTROL software licences are available. In addition, we arrange calibration, IQ/OQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories, extended overtemperature protection with an additional Pt100 sensor, or assistance in selecting the right universal oven for your application? Through our procurement service, we will be happy to assist you with procurement and configuration.
Heidolph Hei-PLATE Mix 20l Magnetic Stirrer, up to 20 Litres, without Heating, 506-54100-00
If a batch requires more volume than a standard hotplate can accommodate, but at the same time does not require a heat source directly beneath the vessel, the Hei-PLATE Mix 20 l provides exactly this combination: stirring of up to 20 l without any heating function; according to the manufacturer, even the heat from the motor is not transferred to the work surface. The chassis is identical in construction to the Hei-PLATE Mix'n'Heat Core, but without the heating module, and covers a speed range from 100 to 1,400 revolutions per minute.No heat input for heat-sensitive substancesFor substances that are sensitive to heat, any additional source of temperature poses a risk, even the waste heat from a motor. The Hei-PLATE Mix 20 l is therefore deliberately designed without a heating function, ensuring that the base remains cool. A soft-start function gently brings the speed up to the set value, ensuring that the sample does not splash at start-up and the stir bar does not veer off course.Large Kera-Disk platform for 20 lThe 145-millimetre-diameter Kera-Disk platform, made of aluminium with a ceramic coating, is chemical-resistant and scratch-resistant, and can support samples weighing up to 25 kilograms. With a power consumption of just 25 watts in normal operation, energy usage remains low for a unit with this stirring capacity; in standby mode, it drops to 1.7 watts. The external dimensions of 168 x 101 x 299 millimetres are consistent with the rest of the Hei-PLATE range, meaning the unit can be integrated into existing workstations without any modifications.Typical applicationsStirring of large-volume batches up to 20 l without heat inputProcessing of heat-labile active ingredients and dyesPreparation of larger volumes of buffers and reagents in routine laboratory workApplications where even minimal motor heat would interfere with the sampleSupplementing a Hei-PLATE workstation with a second, non-heated unitElectrical protection and environmental conditionsDegree of protection IP42 protects against foreign bodies larger than 1 mm and against obliquely falling dripping water; the sound pressure level is below 50 dB(A). The unit operates at 230 volts at 50 or 60 hertz in Europe and 115 volts in the USA, in each case via a connection with L, N and a protective earth conductor. The permissible operating range is from 5 to 31 °C at up to 80 % relative humidity; above this, the permissible humidity decreases linearly down to 40 °C.Selection guide: smaller volume or with heatingIf 5 litres of stirring volume is sufficient, the more compact Hei-Mix S is the simpler alternative. If a heating plate is required, the identically constructed chassis with a heating module, as the Hei-PLATE Mix'n'Heat Core, delivers temperatures up to 300 °C; with additional digital Pt1000 control, it is available as the Hei-PLATE Mix'n'Heat Core+.Technical detailsDimensions (W x H x D)168 x 101 x 299 mmFootprint (Kera-Disk)Ø 145 mm, aluminium, ceramic-coatedWeightapprox. 3 kgMaximum permissible load25 kgDriveEC motor, counter-clockwise rotationSpeed range100 to 1,400 rpmDegree of protection (EN 60529)IP42Sound pressure level< 50 dB(A)Rated voltage230 V, 50/60 Hz (EU); 115 V, 50/60 Hz (US)Connection typeL+N+PEProtection classIOvervoltage categoryIIPollution degree2Power consumption25 W in normal operation, 1.7 W on standbyEMC classB, Group 1Operating temperature5 to 31 °C at up to 80 % relative humidity, 32 to 40 °C at up to 50 % relative humidity (linearly decreasing)Installation altitudeup to 2,000 m above sea levelScope of deliveryHei-PLATE Mix 20 l, order number 506-54100-00The silicone cover for the Hei-PLATE Mix 20 l is not included in the scope of delivery and must be ordered separately.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Heidolph Scientific Products GmbH, is DE 50705753. Information on the return of old appliances can be found on our Environment and disposal page.Warranty and procurement serviceHeidolph Scientific Products GmbH, Schwabach, provides a 3-year manufacturer’s warranty against defects in materials and workmanship. This excludes glass and wear parts, damage caused during transport, and damage resulting from improper use. If the device is registered with Heidolph, the warranty begins on the date of purchase; otherwise, it begins on the date of manufacture as indicated by the serial number. Your statutory warranty rights remain unaffected. For this model in the Hei-PLATE series, Heidolph offers a 10-year warranty provided the instrument is registered with Heidolph within the first year of purchase. Our procurement service can, if required, source the appropriate silicone cover and other accessories for larger stirring volumes.
Memmert IN30 incubator, compact incubator with natural convection, 32 litres, up to 80 °C
With an internal volume of 32 litres, a temperature range of 20 to 80 °C and purely natural convection, the Memmert IN30 incubator is designed as a compact incubator for the incubation and cultivation of samples in microbiology, food analysis and the pharmaceutical industry. An internal glass door allows visual inspection of the cultures without having to open the fully insulated outer door and thereby disturb the internal temperature, a practical difference compared to the pure heating and drying ovens of the UN series.Natural convection for stable incubation conditionsThe Memmert IN30 incubator operates without an air turbine or a forced-air fan; the heat rises within the chamber purely by thermal convection. This is an advantage for the cultivation of microorganisms and cell cultures: there is no forced air movement that could dry out open Petri dishes or affect culture media. The operating temperature range starts at a minimum of 5 °C above room temperature and extends up to 80 °C. A DIN Class A Pt100 temperature sensor with 4-wire measurement ensures a setting accuracy of 0.1 °C across the entire operating range, important for reproducible incubation temperatures, such as 37 °C in microbiology.ControlCOCKPIT SingleDISPLAY and data acquisitionThe IN30 is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphic display. The temperature can be set in Celsius or Fahrenheit, as well as the position of the exhaust air flap, programme duration, time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWAIT function only starts the incubation time once the setpoint temperature has actually been reached, which is important for defined incubation times. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download.Capacity and dimensions of the Memmert IN30 incubatorThe internal chamber measures 400 x 320 x 250 mm, whilst the external dimensions are 585 x 704 x 434 mm. An electropolished stainless steel grid shelf is included in the scope of delivery; the incubator can accommodate up to three shelves in total. The maximum load capacity is 60 kg for the entire unit and 20 kg per shelf, which is more than sufficient for Petri dishes, test tubes and smaller culture vessels. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The IN30 is connected to 230 V (approx. 1,600 W) or 115 V (approx. 800 W), in both cases at 50/60 Hz, with noticeably lower power consumption than the heating ovens of the UN series with their higher temperature range.Selection guide: choosing the right incubator sizeMemmert offers two sizes with natural convection, as well as the forced-air version with TwinDISPLAY for different temperature distribution requirements.ModelInternal volume and controlIN3032 l, natural convection, SingleDISPLAY, max. 3 shelvesIN5553 l, natural convection, SingleDISPLAY, max. 4 shelvesIF30plus32 l, forced air circulation, TwinDISPLAY, max. 3 shelvesFor those who wish to incubate more culture vessels simultaneously whilst still avoiding forced air circulation, the Memmert IN55 incubator with a 53-litre capacity offers the next level. Those who, on the other hand, require active, more uniform air circulation as well as an integrated sterilisation programme will find these functions in the Memmert IF30plus incubator, which is identical in size. The full range of climate chambers and incubators can be found under Climate Chambers & Incubators.Distinction: Incubator versus heating oven, IN versus IFUnlike the universal ovens in the UN series, the IN30 is specifically designed for incubation temperatures up to 80 °C, not for drying or tempering processes up to 300 °C. The inner glass door, included with the IN30, is not part of the standard specification for the UN models and is important for culture monitoring without temperature loss. Within the incubator range, the key purchasing decision is between natural convection (IN series) and forced air circulation (IF series): The IF30plus features an air turbine, two Pt100 sensors for mutual monitoring, a TwinDISPLAY with two screens and a permanently installed sterilisation programme for the interior, all functions that the IN30, with its SingleDISPLAY, does not offer. Those who switch between different sample types and wish to decontaminate the interior between runs are better served by the IF30plus; those who require quiet, vibration-free incubation without air movement are better off sticking with the IN30.Safety according to DIN 12880The IN30 features adjustable electronic temperature monitoring and a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature reaches approximately 20 °C above the maximum chamber temperature, important for incubation runs lasting several days without constant supervision. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. The unit bears CE and EAC markings as well as a UL mark.Installation, operation and disposalFor operation, a minimum distance of 15 cm from the wall and a minimum distance of 20 cm from the ceiling must be maintained; a minimum of 5 cm is sufficient on either side in relation to a wall or neighbouring unit. Installation is permitted at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the IN30 is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The interior and the inner glass door can be cleaned using standard laboratory cleaning agents and disinfectants. As an electrical appliance, the IN30 is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste.Typical areas of applicationWith an internal volume of 32 litres and incubation temperatures of up to 80 °C, the Memmert IN30 incubator is suitable for compact routine applications in microbiology and food technology.Incubation of culture media and cultures in routine microbiological workBacterial count determination and shelf-life testing in food analysisIncubation of small batches in the pharmaceutical industry and researchVisual inspection of ongoing cultures without temperature loss thanks to the internal glass doorCompact entry-level incubator for schools, training and routine laboratoriesReasons for investment: Equipment for day-to-day incubationThe IN30 comes supplied with 1 electropolished stainless steel grid shelf and the internal glass door; the incubator is designed to accommodate up to 3 shelves. For process documentation, we recommend a permanent AtmoCONTROL software licence rather than the time-limited trial version, supplemented by a USB-to-Ethernet adapter. Those wishing to secure access can configure a lockable door with a security lock; for enhanced safety, an additional Pt100 sensor with overtemperature protection is available. For pharmaceutical or standards-compliant applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Those wishing to combine the IN30 with other devices on a shelf or rack will find a space-saving solution in a wall bracket or stacking kit, without taking up any additional floor space.Frequently asked questions before purchaseWhat is the inner glass door for?It allows visual inspection of the cultures without having to open the fully insulated outer door, which reduces temperature fluctuations inside the unit and disturbs the incubation process less.Up to what temperature does the IN30 operate?The adjustable temperature range is from 20 to 80 °C; the operating temperature range starts at a minimum of 5 °C above room temperature.How many culture vessels can fit inside at the same time?One grid shelf is included as standard; up to three shelves, each with a maximum load of 20 kg, are possible, for a total load of up to 60 kg.Is the IN30 different from the UN30 universal oven?Yes, the IN30 is designed for incubation temperatures up to 80 °C and has an internal glass door, whilst the UN30 operates as a heating and drying oven up to 300 °C without an internal glass door.Is the IN30 a medical device?No, according to Memmert’s own MDR classification table, the IN30 is not a medical device; this applies only to the separate m and mplus variants.Is there a version with active air circulation?Yes, the Memmert IF30plus incubator, which is the same size, features forced air circulation, TwinDISPLAY and an integrated sterilisation programme.Is the IN30 suitable for continuous operation over several days?The mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at an excess temperature of approximately 20 °C and is designed for unattended operation.Can the IN30 also be used for drying tasks instead of incubation?In principle, yes, provided the setpoint temperature is within the range of 20 to 80 °C. For higher drying temperatures up to 300 °C, a heating and drying oven from the UN series, such as the Memmert UN30 universal oven, is the more suitable choice.Technical detailsAdjustable temperature range20 to 80 °COperating temperature rangeat least 5 °C above room temperature up to 80 °CTemperature setting accuracy0.1 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 48 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 800 WMaximum number of shelves3Shelves included in scope of delivery1Max. load on unit60 kgMax. load per shelf20 kgInterior materialStainless steel, 4-sided all-round heatingCasing materialTextured stainless steel, galvanised sheet steel rear panelControl systemControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayTimer1 minute to 99 days, digital countdown timerPermissible ambient temperature5 °C to 40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation height2,000 mMarkingsCE, EAC, UL marksScope of delivery1x Memmert IN30 incubatorFactory calibration certificate (calibrated at 37 °C)Fully insulated stainless steel door with 2-point locking mechanism (compression door lock)Inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert IN30 incubator is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29728) or without air slots (B29729). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements & procurement serviceOptions available for the IN30 include interior lighting and a power socket, a lockable door with a security lock, an additional Pt100 sensor with over-temperature protection, and reinforced grid shelves. For data acquisition, a USB-to-Ethernet adapter and AtmoCONTROL software licences are available. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories or assistance in selecting the right incubator for your application? Through our procurement service, we will be happy to assist you with procurement and configuration.
Bürkle stainless steel drum pump with outlet elbow, 91 cm immersion depth, for drums up to 220 l, 5601-0800
The 91-cm version of the Bürkle stainless steel drum pump with an outlet elbow delivers 540 ml per stroke. With an immersion depth suitable for drums up to approx. 220 l, it covers standard 200-litre drums. Delivery rate540 ml/stroke Max. immersion depth91 cm Outer diameter of outlet12 mm Length of outlet elbow290 mm ConnectionFor openings from 32 mm, drum screw connection For containers up toapprox. 220 l Anyone who needs to safely transfer flammable or corrosive liquids from a drum or canister requires more than just a simple hand pump. The Bürkle stainless steel drum pump is a hand-operated reciprocating piston pump, which has been developed specifically for this purpose. Thanks to its electrical conductivity and DEKRA-tested suitability for Ex zones 0, 1 and 2, it can also be used in areas where highly flammable vapours are likely to be present, such as when decanting solvents or other flammable chemicals in workshops, laboratories and production facilities. DEKRA-tested for Ex zones 0, 1 and 2 The drum pump was specially developed for use in Ex zones 0, 1 and 2 and is DEKRA-tested for explosion groups IIA and IIB. Thanks to the electrical conductivity of all parts in contact with the medium, it is suitable for highly flammable and combustible liquids. Important for safe operation: When handling flammable or highly flammable liquids, all parts of the pump must be earthed, for example using an anti-static kit. The pump is not suitable for acetone or similar dehydrating solvents. Material: 1.4301 stainless steel with PTFE seals All parts in contact with the medium are made of corrosion-resistant stainless steel 1.4301 (V2A), which, according to Bürkle, promises a long service life even in damp or aggressive environments. The PTFE seals also ensure high chemical resistance and good sliding properties during pumping, so that the pump remains smooth-running even after prolonged use. Two versions: outlet elbow or hose with tap The Bürkle stainless steel drum pump is available in two versions. The version with an outlet elbow (length 290 mm, outlet outer diameter 12 mm) is suitable for direct filling into a container placed underneath. The version with an outlet hose and tap (hose length 1.2 m, outlet outer diameter 12.8 mm) allows for metered, controlled dispensing thanks to the shut-off tap, even when the receiving vessel is not positioned directly beneath the pump. The outlet elbow and outlet hose can also be swapped, making the pump versatile for a range of filling situations. What immersion depth for which container? The pump is available in three lengths, and the immersion depth is infinitely adjustable. This makes it possible to find the suitable Bürkle stainless steel drum pump for different containers: 36 cm immersion depth: for containers up to approx. 30 l 57 cm immersion depth: for containers up to approx. 60 l 91 cm immersion depth: for containers up to approx. 220 l, such as standard drums The 91 cm version with an outlet elbow covers standard 200-litre drums with its immersion depth. Flow rate and viscosity Depending on the selected immersion depth, the pump delivers between 190 and 540 ml per stroke, which corresponds to a flow rate of 9 to 22 l/min across the entire range. The immersion tube has a consistent diameter of 32 mm, and the pump handles fluids with a viscosity of up to 500 mPa·s. Robust construction, versatile use Stainless steel drum pumps are versatile and suitable for a wide variety of drums, containers and other vessels. The robust construction from high-quality, corrosion-resistant 1.4301 stainless steel ensures, according to Bürkle, a long service life, particularly in damp or corrosive environments. Typical applications Decanting flammable or corrosive liquids and chemicals from drums, canisters and other containers Use in workshops, laboratories and production facilities Filling in Ex zones 0, 1 and 2, provided the pump is earthed in accordance with regulations Choice of immersion depth to suit the container size, from small 30-litre canisters up to 220-litre drums Handling and cleaning To operate, screw on the outlet elbow or hose, insert the pump with the drum screw connection into the drum opening and screw it in hand-tight. After removing the cap, the liquid can be pumped out using the handle on the piston rod. During the final pumping stroke, push the piston rod in as far as it will go before carefully unscrewing the pump from the drum. After use, the drum pump should be rinsed with a pH-neutral liquid. Technical details Product principleManually operated reciprocating piston pump Material of parts in contact with the mediumStainless steel 1.4301 (V2A) Seal materialPTFE Immersion tube diameter32 mm Viscosityup to 500 mPa·s Flow rate (entire range)9 to 22 l/min Immersion depthcontinuously adjustable, max. 91 cm Drive typeManually operated ColourSilver Ex zone0, 1, 2 Explosion groupsIIA, IIB Explosion protection testingDEKRA-tested Electrical conductivityYes Outlet elbow/hoseReplaceable Scope of delivery 1x Bürkle stainless steel drum pump in the selected version (with outlet elbow or with hose and tap) and immersion depth Operating instructions Not included in the scope of delivery: drum screw connection and the anti-static earthing kit required for use with flammable liquids. Individual requirements and procurement service For the mandatory earthing required when transferring flammable liquids, Bürkle offers a suitable anti-static kit (5602-1000), as well as a drum mount (5618-0200) for storing the pump in an upright position between uses. We are happy to source both on request: if you have any questions regarding suitable accessories, spare parts or specific requirements relating to your drum pump, our procurement service will be happy to assist you.
Kern OZL-46 stereo zoom microscopes, zoom 0.7x to 4.5x, LED incident and transmitted light, binocular and trinocular
The Kern OZL-46 series comprises six stereo zoom microscopes with LED incident light and LED transmitted light for assembly and repair workstations, training workshops and testing centres. The zoom range is continuously adjustable from 0.7x to 4.5x; when used with the HWF 10x eyepieces, this provides a total magnification of 7x to 45x. Three models are binocular (OZL 463, OZL 465, OZL 467), and three are trinocular with a third port for a camera (OZL 464, OZL 466, OZL 468). All models have a built-in power supply.Which modelThe binocular models OZL 463, OZL 465 and OZL 467 do not have a camera output. The OZL 463 and OZL 465 are mounted on a column stand; according to the data sheet, they differ in net weight (4.2 kg versus 4.6 kg). According to the data sheet, the OZL 467 has a mechanical stand. Of the trinocular models, the OZL 464 and OZL 466 have a beam splitter ratio of 50:50, meaning that the eyepieces and camera can be used simultaneously. Both are mounted on a column stand and feature a click-stop on the zoom wheel. For the OZL 468, the beam splitter ratio is 0:100 according to the data sheet, and the stand is mechanical, as stated in the data sheet. If you need to document and observe live through the eyepiece at the same time, choose the OZL 464 or the OZL 466. Those who work exclusively at the eyepiece will find the OZL 463, the OZL 465 or the OZL 467 sufficient.Zoom, field of view and click-stopAccording to the data sheet, the zoom wheel on the OZL 464 and OZL 466 has an integrated click-stop. It clicks into defined magnification steps so that a setting, once selected, can be found again reproducibly. The data sheet does not specify a click-stop for the other models. The zoom ratio is 6.4:1. The field of view measures 4.4 to 28.6 mm, the working distance is 105 mm, and the maximum specimen height is 140 mm. The Greenough system provides a stereoscopic image. The tube is inclined at 45° and rotates through 360°; the interpupillary distance ranges from 55 to 75 mm, and the dioptre adjustment operates on both sides from -5 to +5. The HWF 10x eyepieces have a 20 mm field of view, a high eye point and a 30 mm mounting diameter, and are fixed in the tube.Illumination and camera connectionThe incident and transmitted light sources are 3 W LEDs, each of which can be dimmed independently. The contrast method is bright field. A C-Mount adapter is required to connect a camera. Kern lists the microscope camera adapters OZB-A4809 (1x), OZB-A4810 (0.3x) and OZB-A4811 (0.5x), as well as the eyepiece camera adapter OZB-A4863 (1x). For models with a camera output, Kern lists the ODC 241, ODC 825, ODC 832 and ODC 852 cameras. For the OZL 464 and OZL 468, the ODC 854 is added; for the OZL 468, so is the ODC 251.Stand, power and dimensionsAccording to the brochure, the stand allows the microscope head to be removed and fitted into other modular systems, such as a universal stand. The coarse focus mechanism features torque control. The power supply is built-in and operates at 100 to 240 V; it is connected via a power cable. The microscopes measure 300 x 240 x 420 mm. The OZL 463 and OZL 464 have a net weight of approx. 4.2 kg, while the OZL 465, OZL 466, OZL 467 and OZL 468 weigh approximately 4.6 kg.Typical applicationsAssembly and repair workstations, for example in the electronics industryTraining organisations, schools and training workshopsTest centres and quality control: circuit boards and componentsZoology and botany, tissue preparation, dissectionSoldering work and inspection using a camera (OZL 464 and OZL 466)Models at a glanceModelTubeBeam splitter ratioStandClick-StopNet weightOZL 463Binocularnot applicableColumnnoapprox. 4.2 kgOZL 464Trinocular50:50Columnyesapprox. 4.2 kgOZL 465Binocularnot applicableColumnnoapprox. 4.6 kgOZL 466Trinocular50:50Columnyesapprox. 4.6 kgOZL 467Binocularnot applicablemechanicalnoapprox. 4.6 kgOZL 468Trinocular0:100mechanicalnoapprox. 4.6 kgTechnical detailsThese values apply to all models. Any differing values are listed in the model table.Optical systemGreenough, bright fieldTubeInclined at 45°, rotatable through 360°, interpupillary distance 55 to 75 mm, dioptre adjustment on both sides from -5 to +5EyepieceHWF 10x, field of view 20 mm, mounting diameter 30 mm, high eye point, fixedZoom0.7x to 4.5x continuously variable, ratio 6.4:1Click-StopOZL 464 and OZL 466Total magnification7x to 45xField of view4.4 mm to 28.6 mmWorking distance105 mmMaximum sample height140 mmFocusingCoarse focus, torque controlIllumination3 W LED incident light and 3 W LED transmitted light, independently dimmablePower supplyBuilt-in power supply, 100 to 240 V, power cableMains plugEuro plug included in the scope of delivery; UK and CH adapters optional, for OZL 463, 465, 467 and 468 also AUS and USDimensions (W x D x H)300 x 240 x 420 mmStorage temperature-5 °C to 40 °CLabellingCEWarranty (manufacturer)36 months according to Kern, excluding wear partsScope of deliveryOZL 463, OZL 464, OZL 465, OZL 466, OZL 467 or OZL 468 stereo zoom microscope, depending on the modelHWF 10x eyepiecesIEC power cable with Euro plugDust coverEyecupsMultilingual operating instructionsWarrantyAccording to Kern & Sohn, these microscopes come with a 3-year warranty. Kern grants 3 years on products with a list price of €500 or more and 2 years on products below that and on components; wear parts such as batteries and rechargeable batteries are excluded. Warranty repairs are carried out by Kern or by a Kern dealer.DownloadsOperating instructions Kern OZL 463, 464, 465, 466, 467 (PDF)Operating instructions Kern OZL 468 (PDF)Regulatory informationAs electrical devices, the microscopes fall under the ElektroG. The manufacturer Kern & Sohn GmbH is registered under the WEEE registration number DE 80821200. How to return old appliances is described on the page Environment and disposal.Individual requirements and procurement serviceThe following accessories are also available:Eyepieces: OZB-A4632 (HWF 15x), OZB-A4633 (HWF 20x), OZB-A4634 (HWF 25x), OZB-A4635 (HWF 10x with 0.1 mm scale)Attachment lenses: OZB-A4641 (0.5x), OZB-A4644 (0.75x), OZB-A4642 (1.5x), OZB-A4643 (2x). According to the brochure for the OZL 463, OZL 464, OZL 467 and OZL 468; for the OZL 466 only the OZB-A4642, for the OZL 465 none.Further microscope accessories: solder protection lens OZB-A4646, stand insert OZB-A4670, dust cover OBB-A1387Eyepiece cameras: ODC 874, ODC 881Cleaning: cleaning spray OCS-A1101, cleaning kit OCS 901Power cables: 822-903 (UK), MLB-A07 (Euro), YKK-01 (CH)Ready-to-use sets with a camera: OZL 464C825, OZL 464C832, OZL 464T241, OZL 466C825, OZL 466C832, OZL 466T241, OZL 468C825, OZL 468C832, OZL 468T241Enquiries are handled via our procurement service.
Macherey-Nagel VISOCOLOR Fish reagent case, 933101
The VISOCOLOR Fish analysis kit has been specially developed for the analysis of fishing waters. It combines reagents and accessories for the six most important water parameters in a single set: ammonium, nitrate, nitrite, phosphate, pH and total hardness. Six key parameters for water quality Anyone wishing to assess fishing waters can hardly avoid these six parameters: ammonium, nitrate and nitrite indicate nitrogen loading and thus, indirectly, the condition of the fish population; phosphate indicates nutrient inputs and algal growth; whilst pH and total hardness provide the basic data for almost any further hydrological assessment. With a single kit, the most important parameters for a fishing water assessment can be covered directly on site, without having to put together several individual tests. Use in fish farming, club waters and water monitoring Whether monitoring an aquaculture pond, carrying out a routine check by an angling or fishing club on its own waters, or taking a random sample as part of official water monitoring: the kit provides the key parameters needed to identify pollution issues at an early stage, before they endanger fish stocks. As all the tests can be carried out without an additional photometer, the kit can be used directly at the water body, without a power connection or sensitive additional equipment. Ready for immediate on-site use The kit includes a case, test kits, accessories and instructions. Results are interpreted purely visually by colour comparison. The reagents have a shelf life of 1.5 years from the date of manufacture and should be stored at 15–25 °C to ensure that results remain reliable throughout their entire service life. Technical details Hazardous substances Yes Gross weight (including packaging) 1381.5 g Shelf life (from date of manufacture) 1.5 years Storage temperature 15–25 °C Scope of delivery Case, test kits, accessories, instructions Parameters Ammonium, nitrate, nitrite, phosphate, pH, total hardness Photometer included No Packaging dimensions 325 x 238 x 155 mm Trademark VISOCOLOR
Eppendorf Research plus single-channel pipette, variable, 100–1,000 µL, blue, 3123000063
The Eppendorf Research plus for 100 to 1,000 µL is a mechanical single-channel pipette with adjustable volume. The volume is selected in steps of 1 µL and read on the four-digit volume display. The colour code blue belongs to the matching tip, namely epT.I.P.S. 50 to 1,000 µL.Setting the volumeVolume selection, pipetting and tip ejection are handled by separate controls. The pipette works with an air cushion. The smallest adjustable step is 1 µL. Anyone who pipettes preparations in many different volumes manages with an adjustable-volume pipette and does not need a set of fixed-volume pipettes.Tips and colour codeAccording to Eppendorf, the colour of the pipette corresponds to the colour of the matching epT.I.P.S. Here, this is the colour code blue for epT.I.P.S. 50 to 1,000 µL. The colour code depends on the tip and not on the pipette volume. The pipette is an open system, and tips from other manufacturers are possible. However, the measurement deviations apply only with original epT.I.P.S.AdjustingThe pipette can be adjusted temporarily. 5 adjustment seals and an adjustment tool (hex key) are supplied for this purpose. Returning to the factory adjustment is possible without calibration.Typical applicationsTransferring reagents and samples into reaction vesselsPreparing dilution series with changing volumesAliquoting liquids in the range 100 to 1,000 µLMixing solutions by repeated aspiration and dispensingMethods in which the volume changes from preparation to preparationWhen choosing, it helps to look at the volume that occurs most often in daily work. If it is close to the nominal volume, the relative measurement deviation is smaller, as the table below shows.Autoclaving and resistanceThe entire pipette may go into the autoclave at 121 °C and 1 bar for 20 minutes. Disinfectants and decontamination agents are wiped off beforehand. Filter sleeve and protective filter, where present on the model, are autoclaved separately. The pipette is UV-resistant at 254 nm. According to Eppendorf, chemical resistance is high, and special lower parts are available for aggressive chemicals. The pipette is operated at +5 °C to +40 °C and 10 to 95 % relative humidity. For storage, Eppendorf specifies -5 °C to +45 °C.Technical detailsFeatureValueSeriesEppendorf Research plus, mechanicalTypeSingle-channel pipette, adjustable volumeVolume range100 to 1,000 µLStep size1 µLDisplayfour-digit volume displayColour codeblueMatching tipepT.I.P.S. 50 to 1,000 µLAutoclavablefully, 121 °C, 1 bar, 20 minutesUV resistance254 nmOperating conditions+5 °C to +40 °C, 10 to 95 % relative humidityStorage-5 °C to +45 °CStandardConformity with ISO 8655 according to EppendorfManufacturerEppendorfManufacturer number3123000063Measurement deviationsFor this pipette, Eppendorf specifies 3 test volumes. According to Eppendorf, the values apply only with original epT.I.P.S. Eppendorf determines them gravimetrically according to ISO 8655, with 10 determinations per volume and water according to ISO 3696. The systematic error describes how far the mean value deviates from the set volume. The random error describes the scatter of the individual values.Test volumeSystematic errorRandom error100 µL±3 % / ±3 µL±0.6 % / ±0.6 µL500 µL±1 % / ±5 µL±0.2 % / ±1 µL1,000 µL±0.6 % / ±6 µL±0.2 % / ±2 µLScope of deliveryPipetteOperating instructionsCertificateAdjustment tool (hex key)5 adjustment seals for temporary adjustmentPipette greaseDepending on the model, further parts are included, for example an epT.I.P.S. Box 2.0 or a sample bag with epT.I.P.S., a locking ring for deactivating the spring loading, protective filters and a pipette wrench.Accessories and procurementThe Pipette Carousel 2 and the Pipette Stand 2 from Eppendorf are also available. Further epT.I.P.S. and accessories are procured by the procurement service on request.
Heidolph Hei-PLATE Sensor Basic Package Core+ Magnetic Stirrer Set, Ø145 mm, with Pt1000 Probe, 506-21150-00
A digital display on the hotplate and an external temperature probe in the vessel are, for many laboratories, the first step towards traceable temperature control. The Sensor Basic Package Core+ combines the Hei-PLATE Mix'n'Heat Core+ digital magnetic stirrer, with a footprint of 145 millimetres, with an external Pt1000 temperature probe, whilst remaining a basic configuration without a mounting bracket or silicone cover.LCD display and two heating modesThe Hei-PLATE Mix'n'Heat Core+ included in the pack displays speed and temperature on an LCD screen; the dynamic control knobs respond to the speed of hand movement, slow for fine adjustment, fast for larger increments. There are two heating modes to choose from: FAST for rapid heating and PRECISE for control without overshoot. The included Pt1000 temperature probe (V4A, order number 509-67910-00) measures the temperature directly within the medium rather than just on the heating plate, with an accuracy of ±0.2 Kelvin plus the tolerance of the Pt1000 sensor and a resolution of 1 Kelvin. In conjunction with the probe, the magnetic stirrer covers a display and measurement range from 15 to 325 °C.Why the temperature in the medium mattersWithout an external probe, a heating plate only controls the temperature of its own surface, not that of the liquid in the vessel. For buffers, solutions or reaction mixtures with a defined target temperature, this makes a difference, particularly when the volume or shape of the vessel changes. The Pt1000 probe is immersed in the medium and provides the control system with the actual value. This allows the set temperature to be reproduced independently of the vessel.Typical applicationsBuffer and solution preparations with a fixed target temperature in the vesselReaction mixtures where the temperature is to be monitored directly inside the flaskFirst steps towards documented temperature control without additional accessoriesUpgrading an existing Core+ magnetic stirrer with an external sensorSelection guide: Basic or AdvancedIf you wish to secure the sensor permanently and protect the work surface between uses, you’ll find the right equipment in the Sensor Advanced Package Core+, which includes an additional mount and silicone cover. For reflux set-ups with a condenser, there are the dedicated Core+ and Core+ Mini reflux packages. If you do not require an LCD display and are happy with the simpler rotary knob operation, the Sensor Advanced Package Core offers the analogue alternative.Technical detailsDimensions (W x H x D)168 x 101 x 299 mmHeating plate footprintØ 145 mmWeightapprox. 3 kgMaximum permissible load25 kgDriveEC motor, counter-clockwise rotationSpeed range100 to 1,400 rpmHeating power800 W at 230 V (EU), 600 W at 115 V (US)Heating temperature range20 to 300 °CHeating controlPIDDisplayLCD displayTemperature measurement accuracy±0.2 K plus Pt1000 toleranceTemperature measurement resolution1 KDisplay and measurement range with Pt100015 to 325 °CDegree of protection (EN 60529)IP42Sound pressure levelless than 50 dB(A)Rated voltage230 V, 50/60 Hz (EU), 115 V, 50/60 Hz (US)Power consumptionNormal operation 825 W (EU) / 625 W (US), standby 1.7 WScope of deliveryHei-PLATE Mix'n'Heat Core+ magnetic stirrer, 145 mm base area, order number 506-21100-00Pt1000 temperature sensor (V4A), order number 509-67910-00The mounting bracket and silicone cover are not included with this order number; they are part of the more comprehensive Sensor Advanced package.Regulatory informationThe devices in this package are electrical appliances within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Heidolph Scientific Products GmbH, is DE 50705753. Information on the return of old appliances can be found on our Environment and disposal page.Warranty and procurement serviceHeidolph Scientific Products GmbH, Schwabach, provides a 3-year manufacturer’s warranty against defects in materials and workmanship. This excludes glass parts and wear parts, damage caused during transport, and damage resulting from improper use. If the appliance is registered with Heidolph, the warranty commences on the date of purchase; otherwise, it commences on the date of manufacture as indicated by the serial number. Your statutory warranty rights remain unaffected. Heidolph offers a 10-year warranty on the Hei-PLATE series magnetic stirrer included in the pack, provided the instrument is registered with Heidolph within the first year of purchase. This extended warranty does not apply to the temperature probe, which is sold as an accessory. Our procurement service can supply a mounting bracket, silicone cover or other accessories for the Core+ magnetic stirrer as required.
Memmert UF160 universal oven, heating and drying oven with forced air circulation, 161 litres, up to 300 °C
Within the eight-tier UF series with forced air circulation, the Memmert UF160 universal oven marks the exact point at which a benchtop unit becomes a floor-standing cabinet: 161 litres of internal volume, a temperature range from 20 to 300 °C and up to 8 shelves for the daily rotation of different batches. The air turbine, which can be electronically controlled in 10 % increments, actively distributes heat throughout the interior and brings samples up to temperature more quickly and evenly than natural convection alone. From drying freshly cleaned laboratory glassware to tempering, ageing and baking material samples, right through to curing in quality assurance, the UF160 thus covers a wide range of applications in laboratories and industry.Forced air circulation for even temperature distribution and short heating timesThe air turbine in the Memmert UF160 universal oven can be electronically controlled in 10 % increments and actively distributes the heat throughout the interior, rather than simply allowing it to rise, as is the case with a natural convection chamber. As a result, the UF160 operates from a minimum of 10 °C above room temperature up to 300 °C. A natural convection unit already starts operating from around 5 °C above room temperature but, in return, operates without any air movement inside the chamber. A DIN Class A Pt100 temperature sensor with 4-wire measurement ensures a setting accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C. Those who run many different batches with varying setpoint temperatures will benefit from the shorter heating-up phases achieved through active air circulation.ControlCOCKPIT SingleDISPLAY: Operation, programming and data acquisitionThe UF160 is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphics display. The following parameters can be adjusted: temperature in Celsius or Fahrenheit, the speed of the forced air circulation motor, the position of the exhaust air damper, the programme duration, as well as the time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWait function only starts the actual process time once the setpoint temperature has actually been reached, which ensures reproducible results in time-critical drying or ageing processes. The integrated data logger can be read, managed and organised via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download to get you started.Capacity and connections of the Memmert UF160 universal ovenThe interior of the UF160 accommodates up to 8 shelves; 2 electropolished stainless steel grid shelves are included in the scope of delivery. The cabinet has a total load capacity of up to 210 kg, with a maximum load of 20 kg per shelf. The internal usable space measures 560 x 720 x 400 mm; the external dimensions of the cabinet are 745 x 1,104 x 584 mm, and the net weight is approximately 96 kg. The interior consists of easy-to-clean stainless steel, reinforced with deep-drawn ribbing, featuring protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The UF160 can be connected either to 230 V (approx. 3,200 W) or 115 V (approx. 1,800 W), in both cases at 50/60 Hz; a single-phase connection is still sufficient for this size.Selection guide: choosing the right size from the UF rangeThe Memmert UF range comprises eight models with internal volumes ranging from 53 to 1,060 litres, all featuring forced-air circulation and available with TwinDISPLAY. When choosing the right size, the key factors, alongside the internal volume, are the footprint and the number of shelves required; not every larger model automatically requires more floor space.ModelInternal volumeUF5553 l, footprint 585 x 514 mm, max. 4 shelvesUF7574 l, footprint 585 x 514 mm, max. 6 shelvesUF110108 l, footprint 745 x 584 mm, 5 shelves max.UF160161 l, footprint 745 x 584 mm, max. 8 shelvesUF260256 l, footprint 824 x 684 mm, max. 9 shelvesUF450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUF750749 l, footprint 1,224 x 784 mm, max. 14 shelvesUF10601,060 l, footprint 1,224 x 1,035 mm, max. 14 shelvesThe UF160 straddles the line between a benchtop unit and a floor-standing cabinet: whilst having the same footprint as the smaller Memmert UF110 universal oven, it offers significantly more capacity, with 8 shelves instead of 5, in a housing that is only slightly larger. For those who regularly process even larger batches, the next step up is the Memmert UF260 universal oven with a capacity of 256 litres. You can find all models in this range in our Climate Chambers & Incubators range.Distinction: TwinDISPLAY and the natural convection variantWithin the UF160 series, the most important purchasing decision is between SingleDISPLAY and TwinDISPLAY. The UF160 described here operates with a single Pt100 sensor and one display; for unattended processes with higher safety requirements, the Memmert UF160plus universal oven offers two redundant Pt100 sensors with mutual monitoring, as well as two TFT displays instead of one. Those who can do without active air circulation, for example, because samples sensitive to dust or air movement are laid out in the open, will find the Memmert UN160 universal oven to be the direct equivalent, featuring natural convection instead of an air turbine, whilst retaining the same internal volume of 161 litres. Conversely, those who can manage with a smaller volume will save a noticeable amount of floor space with the more compact Memmert UF110 universal oven.Safety according to DIN 12880 for unattended operationIn addition to the adjustable electronic temperature monitoring, the UF160 features a mechanical temperature limiter (protection class 1 according to DIN 12880), which switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature, an important safety feature for overnight or weekend runs. An integrated self-diagnostic system assists with fault-finding, whilst the calibration function allows three freely selectable temperature values to be readjusted. The unit bears CE and EAC markings as well as a UL test mark.Use, installation and disposalWhen operating the UF160, a minimum distance of 15 cm from the wall and a minimum distance of 20 cm from the ceiling must be maintained; a minimum distance of 5 cm from the side of the wall or an adjacent unit is sufficient. The unit may be installed at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the cabinet is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The interior, made of easy-to-clean stainless steel, can be cleaned using standard laboratory cleaning agents; the robust textured stainless steel construction ensures a long service life. As an electrical appliance, the UF160 is subject to the German Electrical and Electronic Equipment Act (ElektroG) at the end of its service life and must not be disposed of with household waste; see Regulatory information below.Typical applicationsWith forced air circulation, an internal volume of 161 litres and an installation altitude of up to 2,000 metres, the Memmert UF160 universal oven is suitable for a wide range of heat treatment processes in both laboratory and industrial settings.Drying laboratory glassware and sample vessels in routine operationsTempering, ageing and baking of material samplesTesting and curing in quality assuranceMaterial testing in industrial manufacturingHeat treatment processes in science and researchAn intermediate size for laboratories that require greater capacity than the UF110 can provideInvestment rationale: SingleDISPLAY or TwinDISPLAYThe scope of delivery for the UF160 includes two electropolished stainless steel grid shelves; the cabinet is designed to accommodate up to eight shelves. For day-to-day operation under supervision, the SingleDISPLAY on the UF160 described here is generally sufficient. However, if drying or ageing processes run unattended overnight or at weekends, the redundant sensor system of the Memmert UF160plus universal oven reduces the risk of a single sensor failure jeopardising the entire batch. For visual inspection without opening the door, a full-view glass door rated up to 250 °C or 300 °C is available as an option, as are interior lighting and reinforced grid shelves or perforated trays for up to 60 kg for heavier samples. Those wishing to use the data logger on a permanent basis rather than just with the time-limited trial version can add an AtmoCONTROL software licence. For pharmaceutical or standard-compliant applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request.Frequently asked questions before making a purchaseHow many samples can the UF160 hold at any one time?Two grid shelves are supplied as standard; it can accommodate up to 8 shelves, each with a maximum load of 20 kg, for a total load capacity of up to 210 kg.How does the UF160 differ from the UF160plus?Both share the same housing and air turbine; the UF160plus also features two redundant Pt100 sensors, TwinDISPLAY, HeatBALANCE and AutoSAFETY for greater process reliability during unattended operation.Is a natural convection model available in this size?Yes, the Memmert UN160 universal oven offers the same internal volume of 161 litres, but operates without an air turbine and is suitable for samples that are sensitive to dust or air movement.What is the accuracy of the temperature control?0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards, measured using a DIN Class A Pt100 sensor with a 4-wire connection.What type of power supply is required?Either 230 V at around 3,200 W or 115 V at around 1,800 W, in both cases at 50/60 Hz; a single-phase supply is sufficient.Is the UF160 suitable for continuous overnight operation?The mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heater off when the temperature rises by approximately 20 °C and is designed for unattended operation.Can a glass door be retrofitted?A full-view glass door rated up to 250 °C or 300 °C is one of the common options for the UF160 and can be selected when placing your order.Technical detailsSetting temperature range20 to 300 °CWorking temperature rangeat least 10 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume161 lInternal dimensions (W x H x D)560 x 720 x 400 mm (depth minus 39 mm for the fan)External dimensions of the housing (W x H x D)745 x 1,104 x 584 mmNet weightapprox. 96 kg230 V connection50/60 Hz, approx. 3,200 W115 V connection50/60 Hz, approx. 1,800 WMaximum number of shelves8Shelves included in the scope of delivery2Max. load on the unit210 kgMaximum load per shelf20 kgInterior materialsStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayTimer1 minute to 99 days, digital countdown clockPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation altitude2,000 mLabellingCE, EAC, UL test markScope of delivery1x Memmert UF160 universal ovenFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel door with a 2-point locking system (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe Memmert UF160 universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29736) or without air slots (B29737). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceThe UF160 is available with, amongst other features, full-view glass doors rated up to 250 °C or 300 °C, interior lighting, reinforced grid shelves and perforated trays up to 60 kg, slide-in or floor-standing drip trays, as well as wall brackets, levelling feet and a mobile or fixed base frame. For data acquisition, a USB-to-Ethernet adapter with a 5 m cable and AtmoCONTROL software licences are available; licences for 21 CFR Part 11 (AtmoCONTROL FDA) are also available. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories, a gas-tight version with gas inlet and outlet, a specific feed-through (14, 23, 38, 57 or 100 mm), or assistance in selecting the right universal oven for your application? Through our procurement service, we’ll be happy to assist you with procurement and configuration.
Memmert UN110 universal oven, heating and drying oven with natural convection, 108 litres, up to 300 °C
The Memmert UN110 universal oven is a heating and drying oven from the Memmert UN series. With an internal volume of 108 litres, it marks the transition from the compact benchtop units of the UN series to a noticeably larger footprint and greater loading capacity, whilst continuing to operate using purely natural convection within a temperature range of 20 to 300 °C. For laboratories that regularly dry, temper or cure larger batches or several batches in parallel, without giving up vibration-free operation, the UN110 is the obvious choice between a compact benchtop unit and a large-volume floor-standing cabinet.Natural convection for larger batchesThe Memmert UN110 universal oven also deliberately does not feature an air turbine or a forced air circulation motor. Heat rises within the chamber purely by convection, without dust or light sample particles being stirred up by a fan. As a result, the working temperature range starts from at least 5 °C above room temperature up to 300 °C. With an internal volume of 108 litres and several shelves occupied simultaneously, uniform natural heat distribution remains crucial, particularly when sensitive or exposed samples must not be affected by air movement. A Pt100 temperature sensor of DIN Class A in a 4-wire configuration ensures a setting accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards.ControlCOCKPIT SingleDISPLAY: Operation and data acquisitionThe UN110 is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphics display. You can set the temperature in Celsius or Fahrenheit, as well as the position of the exhaust air flap, the programme duration, the time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWait function only starts the process time once the setpoint temperature has actually been reached, ensuring reproducible results for larger batches. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download.Capacity and dimensions of the Memmert UN110 universal ovenThe interior measures 560 x 480 x 400 mm, whilst the external dimensions are 745 x 864 x 584 mm, representing a noticeably larger footprint than the smaller UN30, UN55 and UN75 models. The scope of delivery includes two electropolished stainless steel grid shelves, and the cabinet can accommodate up to five shelves in total. The maximum load capacity is 175 kg for the entire unit and 20 kg per shelf. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The UN110 is connected to either 230 V (approx. 2,800 W) or 115 V (approx. 1,800 W), in each case at 50/60 Hz.Selection guide: moving to a larger floor areaThe Memmert UN series with natural convection covers internal volumes ranging from 32 to 749 litres. The UN110 is the first model in the range to feature a noticeably larger footprint compared with the three smaller benchtop models.ModelInternal volumeUN3032 l, footprint 585 x 434 mm, 3 shelves max.UN5553 l, footprint 585 x 514 mm, max. 4 shelvesUN7574 l, footprint 585 x 514 mm, max. 6 shelvesUN110108 l, footprint 745 x 584 mm, 5 shelves max.UN260256 l, footprint 824 x 684 mm, max. 9 shelvesUN450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUN750749 l, footprint 1,224 x 784 mm, max. 14 shelvesAnyone upgrading from the UN75 (74 litres, same footprint as the UN55) who requires more capacity and a higher load capacity per unit will find the UN110 to be the suitable next step. If even that is no longer sufficient, the Memmert UN260 universal oven offers a significantly larger, freestanding model with a capacity of 256 litres. The full range of climate chambers and incubators can be found under Climate Chambers & Incubators.Distinction: natural convection versus forced-air circulationAnyone requiring more active heat distribution and shorter heating times for similar volumes, for example, with densely packed batches of varying sizes, will find the Memmert UF160 universal oven to be the suitable forced air circulation counterpart, featuring an electronically controllable air turbine. Its working temperature range starts at 10 °C rather than 5 °C above room temperature. For samples sensitive to dust or air movement, the natural convection of the UN110 remains the more suitable choice. A significantly more compact natural convection model for smaller sample quantities is the Memmert UN30 universal oven. Like all standard models in the UN series, the UN110 operates with the ControlCOCKPIT SingleDISPLAY, rather than the TwinDISPLAY reserved for the ‘plus’ variants.Safety according to DIN 12880 even for larger batchesThe UN110 features adjustable electronic temperature monitoring and a mechanical temperature limiter (protection class 1 according to DIN 12880), which switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature, an important safety feature for overnight or weekend runs when several shelves are in use simultaneously. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. The unit bears CE and EAC markings as well as a UL test mark.Installation, operation and disposalFor operation, a minimum clearance of 15 cm from the wall and a minimum clearance of 20 cm from the ceiling must be maintained; a minimum clearance of 5 cm is sufficient on either side from the wall or an adjacent unit. With a net weight of around 74 kg, it is recommended that the UN110 be placed on a sturdy, load-bearing base rather than simply on a laboratory bench. It may be installed at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the UN110 is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. As an electrical appliance, the UN110 is subject to the German Electrical and Electronic Equipment Act (ElektroG) at the end of its service life and must not be disposed of with household waste.Typical applicationsWith an internal volume of 108 litres and a load capacity of up to 175 kg, the Memmert UN110 universal oven is suitable for laboratories and businesses that regularly dry or heat-treat large quantities of samples.Drying large quantities of laboratory glassware and sample containersVibration-free drying of dust- or air-sensitive materials in multiple batchesTempering, ageing and firing of material samples in industrial quality assuranceMaterial tests with a higher sample throughput than with the smaller UN modelsScience and research involving varying, sometimes larger, seriesInvestment rationale: Equipment for higher throughputThe scope of delivery for the UN110 includes 2 electropolished stainless steel grid shelves; the cabinet is designed to accommodate up to 5 shelves, each with a maximum load of 20 kg. If you regularly use all levels, you can add further grid shelves or perforated trays. For visual inspection without opening the door, a full-view glass door is available, along with interior lighting and a socket for additional measuring equipment, as well as a levelling or mobile base for flexible repositioning. For gas-tight applications, a corresponding version including gas supply and exhaust is available. For continuous data logging, an AtmoCONTROL software licence is recommended; for applications subject to standards, calibration and IQ/OQ/PQ services are available, including DAkkS calibration on request.Frequently asked questions before making a purchaseWhen is the UN110 a good choice?Compared with compact benchtop units, it offers a significantly larger internal volume and a more robust base, without sacrificing the benefits of natural convection.Will the UN110 still fit on a laboratory bench?With a net weight of around 74 kg and a footprint of 745 x 584 mm, a sturdy, load-bearing base is recommended rather than a standard laboratory bench.How many samples can be loaded at the same time?Up to 5 shelves, each with a maximum load of 20 kg, giving a total load capacity of up to 175 kg.What is the accuracy of the temperature control?The DIN Class A Pt100 sensor, using 4-wire technology, provides an accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards, regardless of the cabinet size within the UN series.Is the UN110 also available with forced air circulation?The direct counterpart with forced air circulation in a similar size range is the Memmert UF160 universal oven, with a capacity of 161 litres and an electronically controlled air turbine.Is a gas-tight design possible?Yes, a virtually gas-tight interior with gas inlet and outlet connections is one of the common options for the UN110.Is the UN110 suitable for unattended operation?The mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating if the temperature rises by approximately 20 °C and is designed for night-time or weekend operation.Technical detailsSetting temperature range20 to 300 °CWorking temperature rangeat least 5 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of the housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 74 kg230 V connection50/60 Hz, approx. 2,800 W115 V connection50/60 Hz, approx. 1,800 WMaximum number of shelves5Shelves included in the scope of delivery2Max. load on the unit175 kgMaximum load per shelf20 kgInterior materialsStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayTimer1 minute to 99 days, digital countdown clockPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation altitude2,000 mLabellingCE, EAC, UL test markScope of delivery1x Memmert UN110 universal ovenFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel doors with a 2-point locking system (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe Memmert UN110 universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceThe UN110 is available with, amongst other features, full-view glass doors, interior lighting and a power socket, a levelling or mobile base frame, reinforced grid shelves and perforated trays, as well as a gas-tight version with various pipe feed-throughs. A USB-to-Ethernet adapter and AtmoCONTROL software licences are available for data acquisition. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories or assistance in selecting the right universal oven for your application? Through our procurement service, we are happy to assist you with procurement and configuration.
IKA T 18 mini digital Solution Disperser Set, brushless motor including tool and stand, 0010015137
Not every laboratory workstation has room for a large drive, and not every sample requires 500 watts of power. The IKA T 18 mini digital Solution (0010015137) is designed precisely for these situations: a compact, brushless disperser set with tool and stand that can be accommodated even in small spaces and is designed for samples with lower viscosity. Compact brushless drive With external dimensions of 66 x 186 x 100 millimetres and a weight of 1.8 kilograms, the drive unit is significantly smaller than the classic T 18 digital. The brushless DC motor delivers 210 watts of input power and 160 watts of output power, and is designed for a maximum viscosity of 2,000 mPas. As with the larger series, the speed range extends from 3,000 to 25,000 revolutions per minute, albeit with a slightly higher deviation of 3 %. Digital display, timer and USB-C The LED display shows the set speed, whilst an integrated timer with its own LED display manages the process time, meaning that runs do not need to be stopped manually. The device can be connected to a documentation system via the USB-C interface. In standby mode, power consumption is just 3 watts, whilst the maximum power consumption of the unit is 250 watts. Power is supplied internally via 48 volts DC at a current draw of 4,500 milliamps; the power supply unit itself covers the range from 100 to 240 volts and can therefore be used worldwide without the need for a separate voltage converter. Designed for smaller volumes and lower viscosity According to the manufacturer, the T 18 mini digital Solution is suitable for simple applications involving the homogenisation of low-viscosity samples. As with the larger model, the processable volume ranges from 0.001 to 1.5 litres; however, the maximum viscosity of 2,000 mPas is lower than that of the T 18 digital, which is 5,000 mPas. For routine samples in life sciences laboratories, training centres or smaller-scale quality control procedures that do not involve particularly tough or high-volume batches, the performance is generally adequate. What the compact design means in everyday use With a footprint that is significantly smaller than that of the classic T 18 digital, the T 18 mini digital Solution can be accommodated even where several workstations are positioned close together, such as in practical training rooms or at smaller fume hood workstations. The lower weight of 1.8 kilograms also makes manual operation more comfortable over longer periods when a stand is not used. Those who regularly switch between several workstations also benefit from the fact that the compact unit is easier to transport than the larger series. Typical applications Homogenisation of low-viscosity samples (according to the manufacturer) Smaller batches in life sciences and teaching laboratories Workstations with limited floor space Processes with documented time control via the integrated timer Brief overview within the T-18 range For those requiring higher viscosity or greater motor power, the larger T 18 digital Solution offers the suitable set with a power consumption of 500 watts instead of 210 watts. The drive unit on its own is available as the T 18 digital ULTRA-TURRAX; the dispersing tool included in the set is also available separately as the S 18 N - 19 G dispersing tool. Technical details Motor power consumption210 WMotor output160 WProcessing volume (H₂O)0.001 to 1.5 lMax. viscosity2,000 mPasSpeed range3,000 to 25,000 rpm, continuously variableSpeed deviation3 %Speed displayLEDMotor typeBrushless (direct current)Noise level without tools75 dB(A)Boom diameter13 mmBoom length160 mmProcess typeBatchTimerYes, LED displayPermissible duty cycle100 %Permissible ambient temperature range5 to 40 °CPermissible relative humidity80 %USB interfaceUSB-CMaximum power consumption250 WStandby power consumption3 WDC voltage48 V=Current consumption4,500 mADimensions (W x H x D)66 x 186 x 100 mm (drive unit)Weight1.8 kg (drive unit, excluding stand and tools)Connected load100 to 240 V, 50/60 Hz, 210 W (max. 250 W)Degree of protectionIP 30 (DIN EN 60529) Scope of delivery 1 x IKA T 18 mini digital ULTRA-TURRAX (drive unit) 1 x S 18 N - 19 G dispersing tool 1 x R 1826 plate stand 1 x R 182 boss head Differences from the neighbouring series If you only require the drive unit without the set, it is available as the T 18 mini digital ULTRA-TURRAX. An overview of all our dispersing units can be found in the ‘Dispersing Units’ category; suitable tools are listed under ‘Dispersing Tools’. Application, installation and maintenance With an IP 30 protection rating, the drive unit is slightly better protected against the ingress of foreign objects than the classic T 18 digital with IP 20; however, it is still not designed to withstand splashing water. Operation is permitted at an ambient temperature of 5 to 40 °C and a relative humidity of up to 80 %. The tool’s supplied PTFE bearing must not run dry; the medium provides both lubrication and cooling. The integrated timer reduces the effort required for manual time control in recurring processes, but does not replace the need to monitor the batch. At the end of its service life, as an electrical appliance, the drive must not be disposed of with household waste, but must be placed in the separate collection for waste electrical and electronic equipment. When the mini drive is a worthwhile investment If the viscosity of the samples is up to a maximum of 2,000 mPas and the focus is on a compact design, a timer and documentation via USB-C, the T 18 mini digital Solution reliably meets these requirements. If, on the other hand, tougher media up to 5,000 mPas are regularly processed, or if the higher power consumption of 500 watts is required, the larger T 18 digital Solution is the more suitable choice. Both sets share the same standard tool, the S 18 N - 19 G, so switching between the two sizes does not necessarily change the choice of tool. For laboratories that need to meet both requirements simultaneously, for example a sensitive batch with low viscosity followed by a tougher sample, it may also be worthwhile to purchase both sizes for different workstations. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service Those who also work with disposable dispersing tools will find the S 18/25-ET50 disposable tube from us to be a practical cleaning aid. Do you also require an additional stand for a second workstation or assistance with the USB connection to your documentation system? Through our procurement service, we support you with procurement and configuration. Frequently Asked Questions For which samples is the T 18 mini digital Solution suitable?According to the manufacturer, it is suitable for simple applications involving the homogenisation of low-viscosity samples, up to a maximum of 2,000 mPas. How does it differ from the larger T 18 digital Solution?The mini drive is brushless with a power consumption of 210 watts instead of 500 watts; it is more compact and designed for a lower maximum viscosity, but features a timer and a USB-C interface. Is a stand included in the scope of delivery?Yes, the set includes an R 1826 plate stand with an R 182 boss head. What is the USB-C interface used for?The USB-C port allows the device to be connected to a documentation system to record process data. What is the drive’s protection rating?IP 30 in accordance with DIN EN 60529, which protects against the ingress of foreign objects larger than 2.5 millimetres, but not against splashing water. Can I operate the drive worldwide without a voltage converter?Yes, the mains adaptor covers a range of 100 to 240 volts at 50/60 hertz.
Memmert UF30 universal oven, 32 l, +20 to +300 °C, SingleDISPLAY
With an internal capacity of 32 litres, the Memmert UF30 universal oven is the smallest model in the UF series and has compact external dimensions of 585 x 704 x 434 mm. Featuring forced air circulation and a temperature range of +20 to +300 °C, it is suitable for drying and heating processes involving individual samples or small batches where floor space is limited but the temperature inside the chamber must still be evenly distributed.Design and air circulationAn electronically controlled, low-noise air turbine circulates the air within the chamber; its speed can be adjusted in 10 % increments. Preheated fresh air is introduced via an electronically adjustable exhaust air damper; the exhaust air outlet with throttle valve can also be controlled electronically. The low-maintenance interior is reinforced with deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system; the housing has a fully galvanised sheet steel rear panel.Control via the ControlCOCKPITThe UF30 is controlled via a ControlCOCKPIT featuring a high-resolution TFT colour graphic display and a DIN Class A Pt100 sensor in a 4-wire configuration. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C onwards. The SetpointWAIT function only starts the process time once the setpoint temperature has actually been reached; a digital countdown timer covers target times ranging from 1 minute to 99 days. Three freely selectable temperature values can be calibrated, whilst a self-diagnostic system assists with troubleshooting. The programme sequence is saved in the event of a power failure, and the data logger can be read out and managed via the Ethernet interface.Safety according to DIN 12880A mechanical temperature limiter, protection class 1 according to DIN 12880, switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature. The door is fully insulated and fitted with a two-point locking mechanism as a compression door lock. The permissible ambient temperature is +5 °C to +40 °C with a maximum relative humidity of 80 % (non-condensing), and the cabinet may be installed at altitudes of up to 2,000 m above sea level. The cabinet must only be transported in an upright position.Selection guide for the correct sizeThe scope of delivery includes a stainless steel grid shelf and up to three possible shelves; the UF30 is designed for small to medium sample quantities; a total load of up to 60 kg and 20 kg per shelf are permitted. Those who regularly wish to dry or temper multiple batches simultaneously will find greater internal volume in the UF55 (53 l) or the UF75 (74 l), as shown in the size table below.Typical applicationsWith an internal volume of 32 litres, the UF30 is suitable for drying, heating, tempering, ageing, baking, testing and curing in research, science, industry and quality assurance.Drying small sample batches in laboratory settingsTempering and curing of individual material samplesPreparing and baking small components in quality assuranceAgeing and testing small samples in research and quality assuranceTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangeat least 10 °C above room temperature up to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor1x Pt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 1,600 WShelves max.3Shelves included in scope of delivery1Max. load on unit60 kgMax. load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe UF series with SingleDISPLAY ranges from 32 to 1,060 litres internal volume, sorted by internal volume:ModelInternal volumeSet temperatureDisplayUF30 (this page)32 l+20 to +300 °CSingleDISPLAYUF5553 l+20 to +300 °CSingleDISPLAYUF7574 l+20 to +300 °CSingleDISPLAYUF110108 l+20 to +300 °CSingleDISPLAYUF160161 l+20 to +300 °CSingleDISPLAYUF260256 l+20 to +300 °CSingleDISPLAYUF450449 l+20 to +300 °CSingleDISPLAYUF750749 l+20 to +300 °CSingleDISPLAYUF10601,060 l+20 to +300 °CSingleDISPLAYThis model is also available with two temperature sensors and two control displays for redundant monitoring in the UF-plus series: UF30plus.Scope of delivery1x Memmert UF30 universal ovenFactory calibration certificate (calibrated at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and Disposal page.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29728) or without air slots (B29729). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the UF30, the following items, amongst others, can be ordered ex-works: a full-view glass door, interior lighting and a socket, as well as a gas-tight version. Accessories available include additional shelves and perforated panels, drip trays, a wall bracket, a USB-to-Ethernet adapter and a stacking kit. For qualification and maintenance, we arrange calibration, IQ/OQ/PQ and maintenance services. Should you have specific requirements or any questions regarding the appropriate equipment, we will be happy to advise you personally.
Our manufacturers from A to Z
For every brand you will find here which of its products we offer in the shop. The name takes you to the manufacturer page or to the filtered articles.
Aqualabo: Portable water analysis meters NEON and ODEON with plug-in digital sensors, for measurements in the field and in the laboratory.
Bandelin: Ultrasonic cleaners and ultrasonic baths SONOREX in the SUPER RK, DIGITEC and SMART series, plus SONOPULS homogenisers. Used in the laboratory for cleaning glassware and instruments, for degassing and homogenising.
bimos: Ergonomic laboratory chairs TEXON and NEON, configurable with castors or glides, plus ESD and cleanroom chairs, saddle stools and sit-stand aids.
BINDER: Climate chambers and incubators from Tuttlingen. In the shop, the constant climate chambers KBF and KBF PRO, cooling incubators KB PRO, drying and heating ovens as well as ultra-low temperature freezers UF V, plus matching accessories such as light modules and shelf sets.
BRAND: Pipettes from the Transferpette S series, single-channel, multichannel and electronic, bottle-top dispensers Dispensette S and S Organic, the bottle-top burette Titrette as well as seripettor and Transferpettor. Liquid handling from Wertheim.
Bürkle: Sampling technology such as ViscoSampler and PharmaScoop, drum pumps in stainless steel and PTFE, safety cans and canisters in stainless steel, laboratory bottles and further laboratory accessories.
DWK Life Sciences: Laboratory glassware under the DURAN brand made from borosilicate glass, in the shop laboratory bottles from 10 ml to 25 l, beakers and flasks. We source the remaining life science consumables in glass and plastic on request.
Elma: Ultrasonic baths Elmasonic Select, Easy and P with heating, in sizes from under one litre to over 27 litres, the P series with switchable frequency of 37 and 80 kHz.
Eppendorf: Pipettes Research plus, Reference 2 and the electronic Xplorer, single-channel and multichannel, plus Multipette dispensers. Centrifuges and reaction vessels from the Eppendorf range on request.
ESAB: Welding accessories for workshop and maintenance, welding wire and TIGROD rods for TIG welding, stick electrodes, electrode holders and torch holders.
Fripa: Paper towels, wipes and further hygiene paper products for laboratory and business use, from Miltenberg.
Giese-GEF: Dangerous goods labels by hazard class, as adhesive film or adhesive paper on rolls, for example for flammable gases of class 2.1 or lithium batteries of class 9, for marking during storage and shipping.
Heidolph: Stirring and evaporation technology from Schwabach. Overhead stirrers Hei-TORQUE, magnetic stirrers Hei-PLATE and Hei-Mix, shakers of the Reax, Titramax and Promax families, peristaltic pumps Hei-FLOW and the rotary evaporator Hei-VAP. The three-year manufacturer's warranty is stated on the product.
IKA: At IKA we are a premium partner. Magnetic stirrers and hot plates, overhead stirrers EUROSTAR, ULTRA-TURRAX dispersers, mills, shakers, thermostats and water baths, rotary evaporators, pipettes, calorimeters and viscometers, plus wear parts such as dispersing tools and grinding jars. The extended warranty on registration is stated on every device.
JULABO: Water baths and shaking water baths, circulators and recirculating chillers from Seelbach. Further devices from the JULABO range on request.
Kern & Sohn: Analytical, precision and counting balances, moisture analysers, refractometers and microscopes, force gauges under the subsidiary brand Sauter. For many scales we arrange the DAkkS calibration certificate from the calibration laboratory in Balingen.
KNF: Chemically resistant diaphragm vacuum pumps and pump systems LABOPORT for vacuum applications in the laboratory, further laboratory pumps on request.
L&R: Latex examination gloves Sentina, ambidextrous. We source further items from the L&R range on request.
LAUDA: Thermostats and circulation chillers from Lauda-Königshofen. Heating and cooling thermostats Alpha, circulators LOOP, circulation chillers Microcool, water baths Hydro and the water stills Puridest.
Liebherr: Laboratory refrigerators and freezers for sample storage according to GLP, pharmacy refrigerators, ultra-low temperature freezers as well as commercial refrigeration and freezing appliances for HACCP-compliant cooling.
Macherey-Nagel: Rapid tests and reagents NANOCOLOR and VISOCOLOR, compact photometer PF-3, spectrophotometers NANOCOLOR VIS II and UV/VIS II, thermoblocks for digestion as well as filter paper circles for filtration.
Meditrade: Powder-free nitrile disposable gloves of the Gentle and Skin series, latex gloves and the couch roll Rollicel.
Memmert: Incubators and climate chambers from Schwabach. Universal ovens, incubators and Peltier-cooled incubators, the CO2 incubator ICO, constant climate chambers, vacuum ovens VO, water baths WTB and ultra-low temperature freezers ULT. We assist with tenders and configuration via m360.
Nabertherm: Muffle furnaces, chamber furnaces and high-temperature furnaces with hinged or lift door in various volumes, built in Lilienthal near Bremen.
Nitras Medical: Disposable clip caps. Further protective equipment and PPE from Nitras Medical, such as gloves, masks and disposable clothing, on request.
Restek: GC capillary columns Rxi and Rtx, HPLC columns, inlet liners and reference standards, i.e. consumables for chromatography.
Sauter: Force gauges, hardness testers, coating thickness gauges and ultrasonic material thickness gauges, the measurement technology brand of Kern & Sohn.
Unigloves: Powder-free nitrile and latex disposable gloves of the Pearl, Black and Select series in several sizes.
WTW: pH electrodes SenTix, laboratory pH meters and buffer solutions from Xylem Analytics, for pH measurement technology in the laboratory.
Why these brands at LT Laborhandel
We have been trading laboratory supplies from Bremen since 2009. In the shop we list what we recommend ourselves and what we can organise spare parts and service for. At IKA, wear parts such as dispersing tools and grinding jars are available directly in the shop, for Kern scales we arrange DAkkS calibration certificates, and at Memmert we help with tenders. For many devices, the manufacturer's data sheet is attached to the product, and at IKA and Heidolph the warranty with its term is also stated there.
Our prices are permanently below the manufacturer's RRP. Manufacturer promotions are added for a limited time and are marked as such.