IKA HB eco Heating Bath (4 L, 99 °C, for RV 3), 0020016337

The RV 10 digital FLEX is the glassware-free version of the digital line: drive, heating bath and 7-segment control are identical to the RV 10 digital V, but the vertical glassware is deliberately missing from the box. Anyone who already owns a receiving flask, condenser or another set of flasks, for example from a decommissioned predecessor device, saves the purchase of duplicate glassware with the FLEX and combines the drive unit freely with existing or desired accessories. At 18.5 kilograms, the basic unit weighs considerably less than the complete versions at around 32 kilograms, which makes transport and installation at cramped workstations easier.Free glassware configuration instead of a fixed setWhether uncoated vertical glassware RV 10.1, the coated version RV 10.10 or a diagonal setup, with the FLEX the laboratory itself decides which glassware combination suits the respective application, and can, if required, continue to use the same glassware between several drive units. As with the complete models, the speed ranges from 5 to 280 revolutions per minute, and a soft start and selectable clockwise/anticlockwise rotation in interval mode protect sensitive samples.Heating bath and safety technology unchangedThe heating bath reaches up to 180 °C with 1 kelvin setting accuracy and holds a maximum of 4 litres, and a timer takes over recurring process steps. The motorised lift automatically raises the flask out of the hot bath on power failure, and individually adjustable safety temperature circuits, dry-run protection and an adjustable end-position detection provide additional protection against glass breakage. The device can be connected to the labworldsoft software via the RS-232 interface. On the mains, the device runs at 220 to 240 volts and a power consumption of 1,400 watts. For other mains voltages, IKA also supplies the same model in the versions 115 V, 100 to 240 V, 100 to 120 V and 100 to 115 V.Typical applicationsReplacement drive where existing glassware is still intactBuilding individual glassware configurations for special distillation tasksSecond device at a site with RV 10 accessories already availableCost-conscious procurement when compatible glassware is already in houseSelection guide: the RV 10 family at a glanceFLEX models like this one differ from the V and V-C solely in the missing glassware, and technically the drive and heating bath are identical. Anyone who does not yet have a firm idea of the suitable glassware combination is usually ready to start sooner with one of the complete models. The following table compares all six RV 10 versions.ModelGlasswareSpeed rangeOperationPumpRV 10 digital VVertical glassware, uncoated5 to 280 rpm7-segment display, manualwithout pumpRV 10 digital V-CVertical glassware, coated5 to 280 rpm7-segment display, manualwithout pumpRV 10 digital FLEX (this product)without glassware5 to 280 rpm7-segment display, manualwithout pumpRV 10 auto pro VVertical glassware, uncoated5 to 300 rpmTFT colour display, vacuum controller integratedVACSTAR digital includedRV 10 auto pro FLEXwithout glassware5 to 300 rpmTFT colour display, vacuum controller integratedVACSTAR digital includedRV 10 auto V Starter SolutionVertical glassware, uncoated5 to 300 rpmTFT colour display, vacuum controller integratedVACSTAR lite and RC 2 lite recirculating chiller includedAnyone who distils smaller sample quantities will find more compact alternatives from the same IKA series family in the RV 3 and the RV 8.Technical detailsWithout glassware, the cooling surface is omitted in the manufacturer's specification, and all other characteristics correspond to those of the RV 10 digital V.Condenser typewithout condenser (glassware to be chosen separately)Motor principleDCSpeed range5 to 280 rpmDirection of rotation reversibleyesLiftmotorised, stroke 140 mmHeating temperature rangeRoom temperature to 180 °CHeating power1,350 WSetting accuracy of set temperature1 KMax. filling volume of heating bath4 lPermissible ambient temperature / humidity5 to 40 °C / 80 %IP ratingIP 20 according to DIN EN 60529Dimensions (W x H x D)500 x 430 x 440 mmWeight (without glassware)18.5 kgRS-232 interfacepresentConnected load220 to 240 V, 50/60 Hz, 1,400 W (other voltage variants 115 V / 100 to 240 V / 100 to 120 V / 100 to 115 V)Scope of deliveryRV 10 digital drive unit (basic unit, without glassware), ident no. 0010004805HB 10 heating bath, filling volume 4 litresBall joint clamp RV 05.10, ident no. 0000736600NS 29 clamp, RV 10.88, ident no. 0003683300Vapour duct tube RV 10.70 (NS 29/32), ident no. 0003812200Seal RV 10.8001, ident no. 0003907000RV 3.4 Woulff bottleRV 3.1 support rodWithout glassware and condenser, which are ordered separately depending on the desired configuration. Suitable glassware sets, evaporating flasks and condensers can be found in the same RV 10 accessory range as for the complete models of the series.Warranty and procurement serviceThe IKA manufacturer's warranty applies to rotary evaporators: 2 years, extended to 5 years if registered at ika.com/register within 90 days of purchase. For the suitable glassware combination for the FLEX drive, our procurement service takes care of the configuration of evaporating flask, receiving flask and condenser.

The RV 10 auto pro FLEX features the full range of automation technology from the auto-pro range, including a TFT colour display, an integrated vacuum controller and the VACSTAR digital vacuum pump, but deliberately does not include a fixed set of glassware. Businesses that already have suitable evaporating and collection flasks, or wish to put together their own glass configuration, can thus avoid having to purchase duplicate glassware. As with the other RV-10 models, the heating bath is built-in, meaning that distillation can begin immediately once your own glassware has been fitted.Automation without fixed glassware specificationsThe integrated vacuum controller automatically regulates the vacuum and the cooling water flow rate and measures with an accuracy of ±1 mbar; a solvent library with 40 entries supports automatic boiling point detection, regardless of which glassware combination is fitted to the unit. Up to ten procedures can be programmed and recalled for batch processing. The rotational speed ranges from 5 to 300 revolutions per minute; for target speeds below 100 rpm, the unit maintains a tolerance of ±1 rpm, and above that, ±1 %.Vacuum pump included, glassware as requiredThe VACSTAR digital vacuum pump is included as part of the scope of delivery, along with two vacuum hoses (0.55 metres each), two cooling water hoses (1 metre each) and a USB cable. For the glass side, the RV-10 accessories list includes both vertical and diagonal glass sets in uncoated and coated versions, allowing the configuration to be tailored precisely to your own samples. When connected to the mains at 100 to 240 volts, the drive unit consumes just 100 watts; in standby mode, power consumption drops to 3.3 watts. The separate heating power of the heating bath is 1,350 watts, with a setting accuracy of 1 Kelvin and a maximum capacity of 4 litres.Typical applicationsAutomated batch runs with customised glass configurationsReplacement drive unit for existing auto-pro systems with existing glassLaboratories that switch between vertical and diagonal glass set-ups depending on the methodUnattended distillations thanks to automatic vacuum and cooling water managementSelection guide: the RV 10 family at a glanceWithin the auto-pro range, this FLEX model differs from the RV 10 auto pro V solely in the absence of glassware; the automation and the pump supplied are identical. The following table compares all six RV-10 variants.ModelGlasswareSpeed rangeOperationPumpRV 10 digital VUncoated vertical glass set5 to 280 rpm7-segment display, manualwithout pumpRV 10 digital V-CCoated vertical glass set5 to 280 rpm7-segment display, manualwithout pumpRV 10 digital FLEXwithout glass set5 to 280 rpm7-segment display, manualwithout pumpRV 10 auto pro VVertical glass set, uncoated5 to 300 rpmTFT colour display, integrated vacuum controllerVACSTAR digital includedRV 10 auto pro FLEX (this product)without glass set5 to 300 rpmTFT colour display, integrated vacuum controllerVACSTAR digital includedRV 10 auto V Starter SolutionUncoated vertical glass set5 to 300 rpmTFT colour display, integrated vacuum controllerVACSTAR lite and RC 2 lite recirculating chiller includedFor those distilling smaller sample volumes, the RV 3 and RV 8 offer more compact alternatives from the same IKA product range.Technical detailsCondenser typewithout condenser (glass set to be selected separately)Speed range5 to 300 rpmSpeed tolerance±1 rpm below 100 rpm, ±1 % from 100 rpmLiftmotor-driven, stroke 140 mmHeating temperature rangeRoom temperature to 180 °CHeating power1,350 WSetting accuracy1 KMax. heating bath capacity4 lVacuum controllerIntegrated, measurement accuracy ±1 mbarVacuum pumpVACSTAR digital, included in the scope of deliveryPermissible ambient temperature / humidity5 to 40 °C / 80 %IP ratingIP 20 in accordance with DIN EN 60529Dimensions (W x H x D)500 x 430 x 440 mmWeight18.6 kgInterfacesRS-232, Micro-USB, analogue outputConnected load100 to 240 V, 50/60 Hz, 100 W (standby 3.3 W)Scope of deliveryRV 10 auto drive unit (basic unit, without glass set), ID no. 0010004818HB 10 heating bath, capacity 4 litresVACSTAR digital vacuum pumpRV 05.10 ball joint clamp, ID No. 0000736600Clamp NS 29, RV 10.88, ID No. 0003683300Vapour feed-through tube RV 10.70 (NS 29/32), ID No. 0003812200Seal RV 10.8001, ID No. 00039070002 vacuum hoses, 0.55 m each2 cooling water hoses, 1 m eachUSB cableExcludes glass set and condenser; these must be ordered separately depending on the desired configuration.Warranty and procurement serviceRotary evaporators and heating baths are covered by the IKA manufacturer’s warranty: 2 years, extended to 5 years upon registration at ika.com/register within 90 days of purchase. The VACSTAR digital vacuum pump included in the package is covered by the IKA 2+1 warranty; upon registration, this is 3 years instead of 5. For the appropriate glassware combination for the FLEX drive, our procurement service will put together a set comprising an evaporating flask, a receiving flask and a condenser, each available in either uncoated or coated versions.

The RV 8 FLEX is the pure drive unit of the IKA RV 8 series, without glassware and without a condenser. Anyone who already has their own glassware in house or wants to select it specifically by process does not have to buy a preconfigured set with the FLEX. The hand lift works manually, and the device manages without a motorised lift and without a vacuum controller, but is ready for immediate use for laboratories that know their distillation routines and value a free choice of glassware combination. An HB 10 heating bath with 4 litre filling volume is included in the scope of delivery despite the reduced equipment. This division is particularly worthwhile with several RV 8 devices operated in parallel: a replacement drive can be mounted quickly on the FLEX without having to order another set of glassware that ends up unused in the cupboard.Free choice of glassware and condenserWithout a fixed set of glassware, the RV 8 FLEX can be fitted with any combination from the IKA RV 10 glassware range, from uncoated vertical glassware through the coated version to the dry ice condenser. This is worthwhile above all for laboratories that run different processes with changing requirements for breakage protection or cooling capacity and do not want to keep several complete devices on hand. The RV 05.10 ball joint clamp and NS 29 clamp are already included, so that separately procured glassware can be mounted directly.Hand lift and safety functionsThe manual lift raises and lowers over a stroke of 120 millimetres, the immersion angle is continuously adjustable, and one-handed operation works for right-handed and left-handed users. If the power fails, an integrated safety lift automatically raises the flask out of the heating bath. Digital displays for rotation speed and heating bath temperature run independently of the chosen glassware configuration, and the speed ranges from 5 to 300 rpm.Heating bath and connected loadThe supplied heating bath heats up to 180 °C with a setting accuracy of 1 kelvin, carrying handles make transport easier, and a key button locks the set temperature against accidental adjustment. A 24-volt DC circuit in the device reduces the risk compared with components carrying mains voltage. On the mains, the RV 8 FLEX runs at 100 to 240 volts and 1500 watts device power consumption, and the heating bath draws up to 1400 watts.Typical applicationsLaboratories with existing glassware that are looking for a new drive unit without duplicate accessoriesChanging distillation processes with different needs for breakage protection or cooling capacityReplacement procurement when only the drive has to be replaced but the glassware is retainedTraining laboratories that demonstrate different sets of glassware on the same driveSelection guide: the RV 8 family at a glanceSix RV 8 versions are available from us, all with a manual hand lift. The FLEX is the only version without any glassware and condenser equipment. It is suitable above all when glassware and condenser are already available or are to be selected separately by process.ModelGlasswareCondenserPeripherals in setRV 8 V-CVertical glassware, coated (RV 10.10)Vertical condenser, 1,500 cm²without pump, without chillerRV 8 FLEX (this product)without glasswarewithout condenserwithout pump, without chillerRV 8 with dry ice condenserEvaporating and receiving flask, without glassware setRV 10.4 dry ice condenser, uncoatedwithout pump, without chillerRV 8 with dry ice condenser, coatedEvaporating and receiving flask, coatedRV 10.40 dry ice condenser, coatedwithout pump, without chillerRV 8 V Starter SolutionVertical glassware, uncoated (RV 10.1)Vertical condenser, 1,500 cm²VACSTAR lite, RC 2 liteRV 8 pro V-C Complete, coated vertical glassVertical glassware, coatedVertical condenserComplete set (details on the product page)Anyone looking for a glassware-free drive unit with TFT display and integrated vacuum controller will find, in the RV 10 auto pro FLEX the automated version with a speed range up to 300 rpm. For smaller sample quantities, the RV 3 FLEX is the more compact alternative from the same series family.Technical detailsCondenser typewithout condenserMotor principleDCSpeed range5 to 300 rpmSpeed tolerance±1 rpm below 100 rpm, ±1 % from 100 rpmLiftmanual, stroke 120 mmHeating temperature rangeRoom temperature to 180 °CHeating power1,400 WSetting accuracy of set temperature1 KMax. filling volume of heating bath4 lPermissible ambient temperature / humidity5 to 40 °C / 80 %Degree of protectionIP 20 according to DIN EN 60529Dimensions (W x H x D)510 x 490 x 345 mmWeight22.37 kgConnected load100 to 240 V, 50/60 Hz, 1,500 W device power consumption, plus 24 V DC circuitScope of deliveryRV 8 drive unit (basic unit), ident no. 0010003488HB 10 heating bath, filling volume 4 litresBall joint clamp RV 05.10, ident no. 0000736600NS 29 clamp RV 10.88, ident no. 0003683300Vapour duct tube RV 10.70 (NS 29/32), ident no. 0003812200Seal RV 10.8001, ident no. 0003907000RV 3.4 Woulff bottle, ident no. 0025004588Warranty and procurement serviceThe IKA manufacturer's warranty applies to rotary evaporators: 2 years, extended to 5 years if registered at ika.com/register within 90 days of purchase. For suitable glassware, a dry ice condenser or a recirculating chiller, our procurement service takes care of the configuration.