Skip to main content Skip to search Skip to main navigation

IKA RV 10 digital FLEX rotary evaporator, without glassware, HB 10 heating bath, up to 280 rpm, 0010004805

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "IKA RV 10 digital FLEX rotary evaporator, without glassware, HB 10 heating bath, up to 280 rpm, 0010004805"

The RV 10 digital FLEX is the glassware-free version of the digital line: drive, heating bath and 7-segment control are identical to the RV 10 digital V, but the vertical glassware is deliberately missing from the box. Anyone who already owns a receiving flask, condenser or another set of flasks, for example from a decommissioned predecessor device, saves the purchase of duplicate glassware with the FLEX and combines the drive unit freely with existing or desired accessories. At 18.5 kilograms, the basic unit weighs considerably less than the complete versions at around 32 kilograms, which makes transport and installation at cramped workstations easier.

Free glassware configuration instead of a fixed set

Whether uncoated vertical glassware RV 10.1, the coated version RV 10.10 or a diagonal setup, with the FLEX the laboratory itself decides which glassware combination suits the respective application, and can, if required, continue to use the same glassware between several drive units. As with the complete models, the speed ranges from 5 to 280 revolutions per minute, and a soft start and selectable clockwise/anticlockwise rotation in interval mode protect sensitive samples.

Heating bath and safety technology unchanged

The heating bath reaches up to 180 °C with 1 kelvin setting accuracy and holds a maximum of 4 litres, and a timer takes over recurring process steps. The motorised lift automatically raises the flask out of the hot bath on power failure, and individually adjustable safety temperature circuits, dry-run protection and an adjustable end-position detection provide additional protection against glass breakage. The device can be connected to the labworldsoft software via the RS-232 interface. On the mains, the device runs at 220 to 240 volts and a power consumption of 1,400 watts. For other mains voltages, IKA also supplies the same model in the versions 115 V, 100 to 240 V, 100 to 120 V and 100 to 115 V.

Typical applications

  • Replacement drive where existing glassware is still intact
  • Building individual glassware configurations for special distillation tasks
  • Second device at a site with RV 10 accessories already available
  • Cost-conscious procurement when compatible glassware is already in house

Selection guide: the RV 10 family at a glance

FLEX models like this one differ from the V and V-C solely in the missing glassware, and technically the drive and heating bath are identical. Anyone who does not yet have a firm idea of the suitable glassware combination is usually ready to start sooner with one of the complete models. The following table compares all six RV 10 versions.

ModelGlasswareSpeed rangeOperationPump
RV 10 digital VVertical glassware, uncoated5 to 280 rpm7-segment display, manualwithout pump
RV 10 digital V-CVertical glassware, coated5 to 280 rpm7-segment display, manualwithout pump
RV 10 digital FLEX (this product)without glassware5 to 280 rpm7-segment display, manualwithout pump
RV 10 auto pro VVertical glassware, uncoated5 to 300 rpmTFT colour display, vacuum controller integratedVACSTAR digital included
RV 10 auto pro FLEXwithout glassware5 to 300 rpmTFT colour display, vacuum controller integratedVACSTAR digital included
RV 10 auto V Starter SolutionVertical glassware, uncoated5 to 300 rpmTFT colour display, vacuum controller integratedVACSTAR lite and RC 2 lite recirculating chiller included

Anyone who distils smaller sample quantities will find more compact alternatives from the same IKA series family in the RV 3 and the RV 8.

Technical details

Without glassware, the cooling surface is omitted in the manufacturer's specification, and all other characteristics correspond to those of the RV 10 digital V.

Condenser typewithout condenser (glassware to be chosen separately)
Motor principleDC
Speed range5 to 280 rpm
Direction of rotation reversibleyes
Liftmotorised, stroke 140 mm
Heating temperature rangeRoom temperature to 180 °C
Heating power1,350 W
Setting accuracy of set temperature1 K
Max. filling volume of heating bath4 l
Permissible ambient temperature / humidity5 to 40 °C / 80 %
IP ratingIP 20 according to DIN EN 60529
Dimensions (W x H x D)500 x 430 x 440 mm
Weight (without glassware)18.5 kg
RS-232 interfacepresent
Connected load220 to 240 V, 50/60 Hz, 1,400 W (other voltage variants 115 V / 100 to 240 V / 100 to 120 V / 100 to 115 V)

Scope of delivery

  • RV 10 digital drive unit (basic unit, without glassware), ident no. 0010004805
  • HB 10 heating bath, filling volume 4 litres
  • Ball joint clamp RV 05.10, ident no. 0000736600
  • NS 29 clamp, RV 10.88, ident no. 0003683300
  • Vapour duct tube RV 10.70 (NS 29/32), ident no. 0003812200
  • Seal RV 10.8001, ident no. 0003907000
  • RV 3.4 Woulff bottle
  • RV 3.1 support rod

Without glassware and condenser, which are ordered separately depending on the desired configuration. Suitable glassware sets, evaporating flasks and condensers can be found in the same RV 10 accessory range as for the complete models of the series.

Regulatory information

This device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.

Warranty and procurement service

The IKA manufacturer's warranty applies to rotary evaporators: 2 years, extended to 5 years if registered at ika.com/register within 90 days of purchase. For the suitable glassware combination for the FLEX drive, our procurement service takes care of the configuration of evaporating flask, receiving flask and condenser.

Skip product gallery

Matching accessories

Discount
Topseller
IKA HB eco Heating Bath (4 L, 99 °C, for RV 3), 0020016337
IKA HB eco Heating Bath (4 L, 99 °C, for RV 3), 0020016337
Manufacturer number: 0020016337

Compact safety heating bath for the RV 3 series The IKA HB eco (0020016337) is a compact, ergonomic safety heating bath with a capacity of 4 litres and heating temperatures from room temperature up to 99 °C. According to IKA, it is intended for rotary evaporators of the RV 3 series (RV 3 V, RV 3 V-C, RV 3 FLEX, RV 3 pro V-C Complete and RV 3 V Starter Solution). Ergonomic carrying handles, an alternating setpoint and actual temperature display (LED), heating temperature adjustment by rotary knob and a USB interface (Micro-USB) are part of the equipment. Heating, control and safety The heating power is 1,400 W, and the setpoint temperature can be set to within 1 K. For 3 l of water at 90 °C, IKA specifies a controller fluctuation of ±1 K and an absolute deviation from the mean of ±2 K. The bath is made of stainless steel 1.4404, and the safety circuit is fixed at 109 °C. According to DIN 12876, the heating bath is classified as class I. Technical details Product type: heating bath Heating power: 1,400 W Heating temperature range: room temperature to 99 °C Temperature display: LED, heating temperature set by rotary knob Setting accuracy of the setpoint temperature: 1 K Controller fluctuation (3 l water, 90 °C): ±1 K, absolute deviation from the mean ±2 K Filling volume max.: 4 l, filling height min. 60 mm Material (in contact with the product): stainless steel 1.4404 Safety circuit: fixed, 109 °C Class according to DIN 12876: I Outer diameter 257 mm, inner diameter 225 mm, outer height 190 mm, inner height 130 mm Dimensions (W x H x D): 330 x 190 x 325 mm, weight 3.9 kg Permissible ambient temperature: 5 to 40 °C, relative humidity 80 % Degree of protection according to DIN EN 60529: IP 21 Interface: USB (Micro-USB) Voltage: 220 to 240 V, 50/60 Hz, power consumption 1,450 W (standby 3 W), further voltage variant 100 to 120 V Scope of delivery 1 x IKA HB eco heating bath 1 x USB cable, USB A to Micro-B, 2 m Note: This is the heating bath only. The rotary evaporator drive, glassware and stand are not included in the scope of delivery. WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service Whether the heating bath fits your existing rotary evaporator is something our individual procurement service will gladly clarify.

Sale price: €1,021.50 Manufacturer's RRP: €1,474.00 30% below manufacturer's RRP
Discount
Topseller
IKA VACSTAR digital Vakuumpumpe, Membranpumpe mit digitaler Drehzahlanzeige, 22 l/min
IKA VACSTAR digital Vacuum Pump, Diaphragm Pump with Digital Speed Display, 22 l/min, 0020016236
Manufacturer number: 0020016236

The IKA VACSTAR digital is a dry 4-chamber diaphragm vacuum pump with digital speed display. Anyone who has so far operated a purely analogue pump without feedback on the current speed can see here at a glance which setting is currently in use, without depending on full automation. The VACSTAR digital is thus positioned between the purely manual VACSTAR lite and the VACSTAR control with integrated vacuum controller: more control than with a purely analogue pump, but without the additional cost of a permanently installed controller when it is not yet needed for the application in question. Digital display with simple turn-and-push operation The parameters are set with a turn-and-push knob, and an LED display shows the current speed in real time. The pumping speed of 22 l/min (1.32 m³/h) and an ultimate vacuum of 2 mbar reliably cover typical tasks such as rotary evaporators, drying ovens or filtrations. The speed range extends from 285 to 1,200 revolutions per minute, regulated by an analogue speed-vacuum control with two-point control for stable, readily reproducible process behaviour. Prepared for later automation An analogue cable for connecting an external vacuum controller of type VC 10 is already included in the scope of delivery. Anyone who wants to run automated processes, for example a programmed distillation ramp, can extend the pump with the VC 10 at any time without having to buy an additional connecting cable and without having to replace the pump itself with another model. For the protection of laboratory air and the environment, the VSE 1 vacuum safety emission condenser is also recommended. It reduces the release of solvent vapours into the room air and can be retrofitted at any time if required. Chemically resistant and designed for continuous operation All parts in contact with the product are made of Al2O3, PTFE, FFPM, PPS and NBR, and the housing of coated die-cast aluminium and thermoplastic. As a dry-running pump, the VACSTAR digital works entirely without operating oil, so oil changes and the disposal of waste oil are eliminated and samples are not contaminated by oil vapours from the pump. This combination of materials makes the pump particularly resistant to aggressive solvents and ensures low-maintenance continuous operation in everyday laboratory work, even with daily changes between different solvents. Connection, format and operating values With dimensions of 150 x 375 x 370 millimetres and a weight of 11.5 kilograms, the VACSTAR digital is designed for a fixed place at the laboratory workstation, for example next to a rotary evaporator or drying oven. It is connected to 100 to 240 volts at 50 or 60 hertz with a device power consumption of 130 watts in operation and 3 watts in standby. Both an RS232 and a USB interface are available for connection to laboratory software, and the housing is classified IP 20. Robust design for daily laboratory use The lower housing made of coated die-cast aluminium in combination with thermoplastic components is designed for daily continuous use in the laboratory. The permissible ambient temperature of 5 to 40 °C and a tolerated relative humidity of up to 80 % at 31 °C, decreasing linearly to a maximum of 50 % at 40 °C, make the pump suitable even for laboratories without continuous air conditioning. With a sound pressure level of 54 dB(A) at minimum pressure, operation next to the workstation remains pleasantly quiet. Typical applications As a digital intermediate step between manual operation and a fully integrated controller, the VACSTAR digital is particularly suitable for the following applications: Rotary evaporator operation with direct reading of the current speed instead of estimating from the scale on the knob Vacuum drying in drying ovens with a traceable speed setting that can be read on the display Vacuum filtration in the routine laboratory where digital control without full automation is already sufficient Laboratory workstations that are to be retrofitted later with a VC 10 vacuum controller for full automation Training and practical courses in which the digital speed display supports participants' understanding of the process Workstations with several users where a traceable speed setting is more important than estimating from a scale Technical details Pump type4-chamber diaphragm vacuum pump, dryDelivery rate max. (50/60 Hz)1.32 m³/h (22 l/min)Ultimate pressure without gas ballast2 mbarSuction stages / cylinders4 / 4Connection diameter suction/pressure side8 mmInlet pressure2 to 1,030 mbarControlTwo-point control, analogue speed-vacuum control, setting via turn-and-push knobSpeed range285 to 1,200 rpmDisplayLEDSound pressure level at min. pressure54 dB(A)Wetted materialAl2O3, PTFE, FFPM, PPS, NBRHousing materialCoated die-cast aluminium / thermoplasticDimensions (W x H x D)150 x 375 x 370 mmWeight11.5 kgPermissible ambient temperature5 to 40 °CPermissible relative humidity80 % (up to 31 °C), decreasing linearly to max. 50 % (at 40 °C)Degree of protection according to DIN EN 60529IP 20InterfacesRS232, USBVoltage / frequency100 to 240 V, 50/60 HzDevice power consumption130 W (standby 3 W) Scope of delivery 1 x IKA VACSTAR digital Vacuum Pump 1 x vacuum hose (1 m) 1 x silencer 1 x USB cable (USB-A to USB-B) 1 x analogue cable for connecting an external vacuum controller (e.g. VC 10) WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service The VC 10 vacuum controller is available as an extension for fully automatic distillations, and for the protection of laboratory air and the environment we also recommend the VSE 1 emission condenser. Further accessories and spare parts are available on request through our procurement service.

Sale price: €2,428.80 Manufacturer's RRP: €3,036.00 20% below manufacturer's RRP
Discount
IKA VACSTAR control Diaphragm Vacuum Pump with Integrated Controller, 22 l/min, 0020109375
IKA VACSTAR control Diaphragm Vacuum Pump with Integrated Controller, 22 l/min, 0020109375
Manufacturer number: 0020109375

The IKA VACSTAR control is a dry, oil-free 4-chamber diaphragm vacuum pump with a factory-integrated vacuum controller. Anyone who has so far operated a separate pump and an additional vacuum controller side by side saves bench space and wiring effort with this 1:1 concept: the control electronics are already in the pump housing, and it is operated via a detachable display that can also be read and operated directly at the fume hood. For recurring distillation routines, for example on a rotary evaporator in routine operation, the separate wiring and configuration of an external controller for each setup is no longer necessary, which makes it easier to switch between several workstations in the laboratory. Integrated controller instead of a separate vacuum regulator The pumping capacity of 22 l/min (1.32 m³/h) and an ultimate vacuum of 2 mbar reliably cover typical tasks such as rotary evaporators, drying ovens or vacuum filtrations. The speed range extends from 285 to 1,200 revolutions per minute, regulated by a ceramic Al2O3 vacuum sensor. Unlike with a plain diaphragm pump, the question of which external controller is suitable no longer arises, because the pump and control unit are already matched to each other. WiCo remote control for operation under the fume hood The TFT display of the WiCo remote control can be detached from the pump and placed separately, for example directly at the fume hood window, while the pump itself stands underneath or beside it and therefore does not have to be operated constantly through the front window. Several operating modes can be selected via the menu: automatic operation with boiling point detection and a stored solvent library, manual operation at a fixed speed, and separate pump-down and cleaning functions. The automatic boiling point detection helps to avoid bumping and to protect samples from loss through pumping down too quickly, especially with low-boiling solvents. Chemically resistant and designed for continuous operation The PTFE diaphragms and chemically resistant materials in the media path make the VACSTAR control robust against aggressive solvent vapours. An integrated valve cleaning function removes solvent residues from the system and thereby extends the service life of the diaphragms, without the pump having to be dismantled for manual cleaning. For the protection of laboratory air and the environment, the VSE 1 emission condenser can be connected afterwards, so that solvent vapours do not enter the room air unfiltered. As the pump works as a dry-running pump, oil changes are also eliminated, and with them the risk of oil vapours coming into contact with the sample. Connection and format for fixed laboratory workstations With dimensions of 270 x 435 x 500 millimetres and a weight of 14 kilograms, the VACSTAR control is designed for a fixed place at the workstation, for example directly under the fume hood bench, rather than for frequent transport between workstations. Data connection is via USB and RS232, for example for process documentation with laboratory software. The housing is classified IP 20, the device power consumption is 140 watts in operation and 1.5 watts in standby, and the pump is connected to 100 to 240 volts at 50 or 60 hertz. Reproducible processes thanks to automatic boiling point detection The stored solvent library automatically recognises common solvents from their boiling behaviour and adjusts the vacuum accordingly, instead of the target speed having to be readjusted manually. This reduces the variation between individual distillations and makes it easier to hand a process over to changing laboratory staff, because the parameters can be documented and repeated on the device. In combination with the USB or RS232 connection to laboratory software, the complete course of the process can also be logged, which means a noticeable time saving compared with a manually kept process file, especially in quality-assured environments with batch documentation. Typical applications As a 1:1 vacuum solution with integrated controller, the VACSTAR control is particularly suitable for the following applications: Automated distillations on the rotary evaporator with boiling point detection, also with changing solvents Vacuum drying in drying ovens with reproducible, documented process parameters Vacuum filtration where documented, repeatable process control is also required Laboratory workstations with limited space where a separate vacuum controller does not fit Process documentation via USB or RS232 in quality-assured laboratory environments Fixed vacuum workstations where several users are to run the same process reproducibly Technical details Pump type4-chamber diaphragm vacuum pump, dry, with integrated controllerPumping speed max.22 l/min (1.32 m³/h)Ultimate pressure2 mbarInlet pressure1 to 1,030 mbarSpeed range285 to 1,200 rpmNumber of cylinders4Connection diameter suction/pressure side8 mmVacuum sensorCeramic (Al2O3)Controller / operationIntegrated, detachable WiCo display with touch operationOperating modesAutomatic with boiling point detection, manual operation, pump-down and cleaning functionInterfacesUSB, RS232Degree of protection according to DIN EN 60529IP 20Dimensions (W x H x D)270 x 435 x 500 mmWeight14 kgVoltage / frequency100 to 240 V, 50/60 HzDevice power consumption140 W (standby 1.5 W) Scope of delivery 1 x IKA VACSTAR control Vacuum Pump with Integrated Controller 1 x WiCo remote control WH11 (detachable control unit) 1 x power supply OS 1.0 for the WiCo remote control 1 x power cord (according to the IKA instructions) 1 x vacuum hose (1 m) 1 x USB cable (USB-A to Micro-B, 2 m) 1 x USB cable (USB-A to USB-B) 1 x screwdriver WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements & procurement service For additional protection of laboratory air and the environment, the VSE 1 emission condenser can be retrofitted, as can a Woulff bottle to protect the pump from liquid surges or suitable connecting hoses for your rotary evaporator. For technical advice, please contact our procurement service.

Sale price: €3,890.40 Manufacturer's RRP: €4,863.00 20% below manufacturer's RRP
Discount Promo
Topseller
IKA VACSTAR lite Starter Solution, diaphragm vacuum pump, including emission condenser, 9 mbar, 0010014496
IKA VACSTAR lite Starter Solution, diaphragm vacuum pump, including emission condenser, 9 mbar, 0010014496
Manufacturer number: 0010014496

The IKA VACSTAR lite Starter Solution (MPN 0010014496) is a pre-assembled entry-level vacuum package for everyday laboratory use: a compact, oil-free diaphragm vacuum pump combined with the VSE 1 emission condenser. For example, anyone working with a rotary evaporator or setting up a filtration system does not need to purchase and set up the condenser separately, but can put the set into operation straight away. The pump thus handles standard tasks such as filtration, drying in a vacuum drying oven or evacuating Schlenk lines. Compact two-cylinder pump with robust suction capacity At its core is a dry two-cylinder diaphragm pump with a maximum pumping speed of 1.0 cubic metres per hour (16.67 litres per minute) and an ultimate vacuum of 9 mbar without gas ballast. The speed can be continuously adjusted via a rotary knob; the speed range is between 285 and 1,100 revolutions per minute, with a rated speed of 1,100 rpm. This is sufficient for most routine laboratory tasks, but is clearly intended for applications that do not require extremely low ultimate vacuums, such as simple filtration or the drying off of solvents at moderate temperatures. VSE 1 emission condenser for solvent vapours The VSE 1 vacuum safety emission condenser included in the set captures solvent vapours before they are released into the room air via the pump. This allows the condensed solvent to be recovered rather than wasted. Particularly when working with volatile organic solvents in fume hoods or on rotary evaporators, this can reduce consumption and the volume of waste to be disposed of, without the need to procure and adapt a separate component. Chemical-resistant and low-maintenance in continuous operation As a dry-running pump, the VACSTAR lite operates entirely without operating oil, thus eliminating the need for oil changes, waste oil disposal and the risk of sample contamination from oil vapours. All parts in contact with the medium are made of Al₂O₃, PTFE, FFPM, PPS and NBR, whilst the housing is made of coated die-cast aluminium and thermoplastic. According to the manufacturer, this combination of materials is designed for use with aggressive chemicals and solvent vapours and can reduce maintenance requirements during continuous operation. Space-saving and easy to integrate Measuring 115 x 292 x 280 millimetres and weighing 8.5 kilograms, the VACSTAR lite fits even on small work surfaces or directly inside a fume hood. Connections are made via 8-millimetre hose connections on the suction and discharge sides; the housing is rated to IP 20. The sound pressure level is 54 dB(A) at low pressure. A USB interface and an analogue input are available for connection to external control systems, for example if a digital vacuum controller is to be retrofitted at a later date. Simple operation with no training required The ‘lite’ version deliberately omits a digital display and focuses purely on functionality: a rotary knob continuously adjusts the speed and thus the pumping capacity, whilst a non-return valve protects the system against backflow when the pump is switched off. This makes the pump particularly suitable for workstations where several people with varying levels of experience use the same unit, for example during practical sessions or in teams with frequently changing personnel. Wide range of applications in everyday laboratory work IKA positions the VACSTAR-lite series as a universal vacuum source for use with rotary evaporators, laboratory reactors, temperature-controlled chambers, centrifuges and other laboratory equipment. Manual operation via the rotary knob means the pump does not require additional control software. For workstations where more precise, automated process control is required at a later stage, an external vacuum controller can be retrofitted via the analogue interface if necessary, without having to replace the pump itself. Typical applications As an entry-level solution for generating vacuum in the laboratory, the VACSTAR lite Starter Solution is particularly suitable for the following applications: Vacuum filtration in routine analysis, for example when filtering precipitates Support for rotary evaporators for moderate distillation tasks Drying of samples or glassware in a vacuum drying oven Evacuating Schlenk lines and simple desiccators An introduction to vacuum technology for training and teaching, thanks to simple rotary knob operation requiring no lengthy familiarisation Technical details Pump type2-cylinder diaphragm vacuum pump, dryMax. pumping speed (50/60 Hz)1.0 m³/h (16.67 l/min)Ultimate vacuum without gas ballast9 mbarStages / cylinders2 / 2Inlet pressure10 to 1,030 mbarSpeed range285 to 1,100 rpm (rated speed 1,100 rpm)ControlContinuously variable speed control via rotary knob, two-point controlSuction/discharge connectionHose nozzle Ø 8 mmMaterials in contact with the productAl₂O₃, PTFE, FFPM, PPS, NBRHousing materialCoated die-cast aluminium / thermoplasticDimensions (W x H x D)115 x 292 x 280 mmWeight8.5 kgDegree of protection according to DIN EN 60529IP 20Sound pressure level at low pressure54 dB(A)Permissible ambient temperature5 to 40 °CPermissible relative humidity80 % (up to 31 °C), decreasing linearly to a maximum of 50 % (at 40 °C)InterfacesUSB, analogue inputVoltage / Frequency100 to 240 V, 50/60 HzDevice power consumption120 W (5 W on standby) Scope of delivery 1 x IKA VACSTAR lite vacuum pump 1 x VSE 1 vacuum safety emission condenser 1 x vacuum hose 1 x power supply unit Operating instructions WarrantyManufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.Individual requirements and procurement service If you wish to control the VACSTAR lite automatically at a later date, you can retrofit it with a digital vacuum controller such as the VC 10 lite, for example to set programmed ramp profiles on the rotary evaporator. A Woulff bottle to protect the pump from liquid hammer, as well as other original accessories from the IKA vacuum range, are also available via our procurement service. Further information and contact details can be found on our procurement service page.

Sale price: €1,966.80 Manufacturer's RRP: €2,523.00 22% below manufacturer's RRP