With stacking corners, connecting plate for the rear and 2 wall brackets
With base riser so that forklift trucks can drive underneath
With levelling castors
Suitable for 2 Memmert models in sizes 180 and 240
ⓘ This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.
Product information "Memmert mobile stacking kit B68476 for CO₂ incubator ICO 180 and 240"
The mobile stacking kit B68476 is intended for stacking 2 units of the same size. It consists of stacking corners, a connecting plate for the rear, two wall brackets, a base riser that allows forklift trucks to drive underneath, and levelling castors.
It is suitable for the ICO NextGen CO₂ incubators in sizes 180 and 240. Both units in a stack must be of the same size. The size corresponds to the number in the unit name, for example ICO180 or ICO240.
Typical applications
Typical uses in the compatible units:
Stacked installation of several units where floor space is limited, for example in the ICO180
Incubation of larger sample quantities or several test series at the same time, for example in the ICO180
High sample throughput or several parallel test series in a single unit, for example in the ICO240
1 mobile stacking kit (stacking corners, connecting plate for the rear, 2 wall brackets, base riser that allows forklift trucks to drive underneath, levelling castors)
Individual requirements & procurement service
For stacking kits for other ICO sizes and for further accessories for the ICO CO₂ incubator, our procurement service accepts enquiries.
Pre-order: The ICO180 is part of the new ICO NextGen range. It is available as a pre-order.
The Memmert ICO180 NextGen CO₂ incubator takes the place of the previous ICO150 in the new size range, but with an internal volume of 177 litres, it offers significantly more space than its predecessor, which had a volume of 156 litres. Those who have previously used the ICO150 for larger sample quantities will find the ICO180 offers noticeably more space, whilst occupying a comparable position between the medium-sized ICO105 and the large ICO240.
A touchscreen instead of two displays
Instead of the previous TwinDISPLAY with two separate TFT screens, the ICO180 NextGen displays actual and target values as well as parameter trends on a 6.86-inch IPS touchscreen with multi-touch functionality (480 x 1280 pixels).
Temperature and CO₂ control
The temperature can be set from +20 to +50 °C; the operating range extends from at least 5 °C above room temperature up to +50 °C, with a setting accuracy of 0.1 °C. At 37 °C, the temporal temperature fluctuation is ±0.1 K, and the spatial fluctuation is ±0.3 K. CO₂ control covers 0 to 20 % CO₂ as standard, with a setting accuracy of 0.1 % and a temporal fluctuation of ±0.2 % CO₂.
Humidity and O₂ as an extension
A stainless-steel water tray is supplied as standard. Option K7 extends the ICO180 to include active humidity control from 40 to 98 % rh, including a ‘rh off’ function, with a setting accuracy of 0.1 % rh, utilising a self-priming micro-dosing pump with a hot steam generator for humidification and a diaphragm pump for dehumidification. Option T6 (requires Option K7) additionally controls the oxygen concentration via nitrogen injection in the range 1 to 20 % O₂, with an accuracy of 0.1 %.
Six shelves and two glass doors optional
With up to 6 possible shelves, the ICO180 offers more loading flexibility than the smaller models in the series; 2 stainless steel perforated shelves are supplied as standard. Option K4 equips the interior with two glass-panelled doors instead of the solid stainless steel door, allowing a quick view inside the unit without completely altering the internal climate. An integrated battery storage unit (Option C2) keeps the display unit running without interruption in the event of a power cut, ensuring seamless documentation even during an outage.
Sterilisation without removing sensors
A pre-programmed cycle sterilises the interior in 60 minutes at +180 °C without the need to remove the sensors beforehand.
Interior and door
The deep-drawn interior is made of stainless steel grade 1.4301 (ASTM 304). The fully insulated stainless steel door closes with a 2-point compression lock and features an internal glass door; maximum load: 15 kg per shelf and 90 kg per unit.
Interfaces and software
The ICO180 NextGen features USB-C and Ethernet LAN. The chargeable software application myChamber LIMS is available for connection to a LIMS, whilst the connectivity package for the myChamber Monitoring App is available for permanent remote monitoring. For electronic signatures according to 21 CFR Part 11, the basic licence FDAQ1 for AtmoCONTROL FDA and myChamber Control FDA can be added. None of the three options is included as standard.
Operation and connected load specifications
The ICO180 NextGen is rated for 230 V, 50/60 Hz; Option X2 converts it to 115 V at no extra charge, and the power consumption is approximately 1,550 W. The textured stainless steel housing measures 748 x 793 x 689 mm (width x height x depth), plus a 50 mm allowance for the door handle; the internal dimensions are 600 x 590 x 500 mm. The net weight is 98 kg; when packed, it weighs 116 kg. Anyone wishing to stack two ICO180 units on top of one another can use a stacking kit (item no. B64732) or a mobile stacking kit with a raised base (item no. B68476).
Other sizes in the ICO NextGen series
In addition to the ICO180 (177 litres), we offer the ICO50 (56 litres) and the ICO105 (108 litres) for smaller batches, as well as the ICO240 (243 litres) for the highest throughput, each featuring the same operating concept.
Typical applications
With its large internal volume, controlled temperature and CO₂ concentration, the ICO180 NextGen is suitable for:
Incubation of larger sample volumes or multiple experimental runs simultaneously
Microbiological, pharmaceutical and biotechnological research with higher throughput
Laboratory operations where glass doors (Option K4) allow visual monitoring without a complete change in the internal climate
Stacked configuration of multiple units where floor space is limited (stacking kit accessory)
Technical details
Internal volume177 litres
Internal dimensions (W x H x D)600 x 590 x 500 mm (depth minus 37.5 mm for the fan)
Cabinet dimensions (W x H x D)748 x 793 x 689 mm (plus 50 mm door handle)
Interior materialStainless steel grade 1.4301 (ASTM 304), deep-drawn
Temperature setting range+20 to +50 °C
Operating temperature rangeat least 5 °C above room temperature up to +50 °C
Temperature accuracy0.1 °C (temporal variation at 37 °C ±0.1 K, spatial ±0.3 K)
CO₂ control0 to 20 % CO₂, accuracy 0.1 %, temporal variation ±0.2 % CO₂
Humidity control (Option K7)40 to 98 % rh and rh-Off, accuracy 0.1 % rh
O₂ control (Option T6, requires K7)1 to 20 % O₂, accuracy 0.1 %
Control unit6.86" IPS touchscreen (480 x 1280 pixels), multi-touch
DoorFully insulated stainless steel door, 2-point locking, internal glass door (optional: 2 doors with glass cut-outs, Option K4)
Shelves2x stainless steel perforated shelves included in the scope of delivery, up to 6 possible
Max. load90 kg total / 15 kg per shelf
Installation4 adjustable feet
InterfacesUSB-C, Ethernet LAN
Factory calibration certificate+37 °C, 5 % CO₂ (standard; with option K7 additionally 90 % rh, with K7 and T6 additionally 10 % O₂)
Voltage/Power230 V, 50/60 Hz, approx. 1,550 W (Option X2: 115 V at no extra cost)
Net weight/Gross weight98 kg / 116 kg
Scope of delivery
1x Memmert ICO180 NextGen CO₂ incubator (basic unit)
2x stainless steel perforated shelves
1x stainless steel water tray
1x CO₂ connection set (hose with connector and hose clamp)
1x factory calibration certificate (+37 °C, 5 % CO₂)
Not included in the scope of delivery: active humidity control (Option K7), O₂ control (Option T6), glass doors (Option K4), battery storage (Option C2), stacking kits and the water canister with connection hose (only when option K7 is ordered) are additional options, as are the software licences for myChamber LIMS, the Monitoring App and FDAQ1.
Regulatory information
Manufacturer’s WEEE registration number (Memmert GmbH + Co. KG, Stiftung EAR): DE 66812464. The ICO180 NextGen is not a medical device. Memmert is discontinuing the separate, previous ICOmed medical device series (last order 6 November 2026); according to Memmert, the ICO NextGen is currently undergoing testing and qualification to also meet the requirements for medical applications; this is an announcement, not an approval that has already been granted.
Individual requirements and procurement service
Memmert units bought from us are covered for three years from delivery: the first 12 months are followed by a 24-month warranty under Memmert’s terms, handled through us. Your statutory rights remain unaffected. Our procurement service can assist you with additional stainless steel perforated shelves, the K7, T6, K4 or C2 options, a stacking kit for stacking two ICO180 units on top of one another, or a bespoke calibration. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.
Pre-order: The ICO240 is part of the new ICO NextGen series. It is available as a pre-order.
With an internal volume of 243 litres, the Memmert ICO240 NextGen CO₂ incubator is the largest model in the new series, offering two litres more capacity than the previous ICO240 from the 2012 generation. With up to 9 possible shelves, it is suitable for laboratories with high sample throughput or multiple users who load the same incubator simultaneously.
A touchscreen display instead of two screens
Instead of the previous ControlCOCKPIT TwinDISPLAY with two separate TFT screens, the ICO240 NextGen displays actual and setpoint values as well as parameter trends on a 6.86-inch IPS touchscreen with multi-touch functionality (480 x 1280 pixels).
Temperature and CO₂ control
The temperature can be set from +20 to +50 °C; the operating range extends from at least 5 °C above room temperature to +50 °C, with a setting accuracy of 0.1 °C. At 37 °C, the temporal temperature fluctuation is ±0.1 K, and the spatial fluctuation is ±0.3 K. CO₂ control covers 0 to 20 % CO₂ as standard, with a setting accuracy of 0.1 % and a temporal fluctuation of ±0.2 % CO₂.
Humidity and O₂ as an extension
A stainless-steel water tray is supplied as standard. Option K7 extends the ICO240 to include active humidity control from 40 to 98 % rh, including a ‘rh off’ function, with a setting accuracy of 0.1 % rh, utilising a self-priming micro-dosing pump with a hot steam generator for humidification and a diaphragm pump for dehumidification. Option T6 (requires Option K7) additionally controls the oxygen concentration via nitrogen injection in the range 1 to 20 % O₂, with an accuracy of 0.1 %.
Nine shelves and three glass doors optional
With up to 9 possible shelves, the ICO240 has the largest loading capacity in the series; 2 stainless steel perforated shelves are included as standard, with a maximum load of 15 kg per shelf and 135 kg per unit in total. Option K4 equips the interior with three glass-panelled doors instead of the solid stainless steel door, the highest number in the series for this size, which is practical when several users wish to keep an eye on different areas without having to open the entire door every time. An integrated battery storage unit (Option C2) keeps the display unit running without interruption in the event of a power cut.
Sterilisation without removing sensors
A pre-programmed cycle sterilises the interior in 60 minutes at +180 °C without the need to remove the sensors beforehand. This simplifies switching between different culture batches in day-to-day laboratory work.
Interior and door
The deep-drawn interior is made of stainless steel grade 1.4301 (ASTM 304). The fully insulated stainless steel door closes with a 2-point compression lock and features an internal glass door.
Interfaces and software
The ICO240 NextGen features USB-C and Ethernet LAN. The chargeable software application myChamber LIMS is available for connection to a LIMS, whilst the connectivity package for the myChamber Monitoring App is available for permanent remote monitoring. For electronic signatures according to 21 CFR Part 11, the basic licence FDAQ1 for AtmoCONTROL FDA and myChamber Control FDA can be added. None of the three options is included as standard.
Operation and connected load specifications
The ICO240 NextGen is rated for 230 V, 50/60 Hz; Option X2 converts it to 115 V at no extra cost; power consumption is approximately 1,750 W, the highest figure in the series. The textured stainless steel housing measures 748 x 1013 x 689 mm (width x height x depth), plus a 50 mm allowance for the door handle; the internal dimensions are 600 x 810 x 500 mm. The net weight is 113 kg; when packed, it weighs 132 kg; delivery and installation should be planned accordingly.
Other sizes in the ICO NextGen series
In addition to the ICO240 (243 litres), we offer the ICO50 (56 litres) and the ICO105 (108 litres) for smaller applications, as well as the ICO180 (177 litres, successor to the previous ICO150), each featuring the same operating concept and the same control parameters.
Typical applications
With the largest internal volume in the range, as well as controlled temperature and CO₂ concentration, the ICO240 NextGen is suitable for:
High sample throughput or multiple parallel test series in a single unit
Microbiological, pharmaceutical and biotechnological research requiring a large amount of space
Laboratory operations with multiple users who can access specific areas via the optional glass doors (Option K4, 3 doors)
Laboratory operations involving frequently changing culture batches, thanks to the integrated sterilisation function
Technical details
Internal volume243 litres
Internal dimensions (W x H x D)600 x 810 x 500 mm (depth minus 37.5 mm for the fan)
Cabinet dimensions (W x H x D)748 x 1013 x 689 mm (plus 50 mm door handle)
Interior materialStainless steel grade 1.4301 (ASTM 304), deep-drawn
Temperature setting range+20 to +50 °C
Operating temperature rangeat least 5 °C above room temperature up to +50 °C
Temperature accuracy0.1 °C (temporal variation at 37 °C ±0.1 K, spatial ±0.3 K)
CO₂ control0 to 20 % CO₂, accuracy 0.1 %, temporal variation ±0.2 % CO₂
Humidity control (Option K7)40 to 98 % rh and rh-Off, accuracy 0.1 % rh
O₂ control (Option T6, requires K7)1 to 20 % O₂, accuracy 0.1 %
Control unit6.86" IPS touchscreen (480 x 1280 pixels), multi-touch
DoorFully insulated stainless steel door, 2-point locking, internal glass door (optional: 3 doors with glass cut-outs, Option K4)
Shelves2x stainless steel perforated shelves included in the scope of delivery, up to 9 possible
Max. load135 kg total / 15 kg per shelf
Installation4 adjustable feet
InterfacesUSB-C, Ethernet LAN
Factory calibration certificate+37 °C, 5 % CO₂ (standard; with option K7 additionally 90 % rh, with K7 and T6 additionally 10 % O₂)
Voltage/Power230 V, 50/60 Hz, approx. 1,750 W (Option X2: 115 V at no extra charge)
Net weight/Gross weight113 kg / 132 kg
Scope of delivery
1x Memmert ICO240 NextGen CO₂ incubator (basic unit)
2x stainless steel perforated shelves
1x stainless steel water tray
1x CO₂ connection set (hose with connector and hose clamp)
1x factory calibration certificate (+37 °C, 5 % CO₂)
Not included in the scope of delivery: active humidity control (Option K7), O₂ control (Option T6), glass doors (Option K4), battery storage (Option C2), stacking kits and the water canister with connection hose (only when option K7 is ordered) are additional options, as are the software licences for myChamber LIMS, the Monitoring App and FDAQ1.
Regulatory information
Manufacturer’s WEEE registration number (Memmert GmbH + Co. KG, Stiftung EAR): DE 66812464. The ICO240 NextGen is not a medical device. Memmert is discontinuing the separate, previous ICOmed medical device series (last order 6 November 2026); according to Memmert, the ICO NextGen is currently undergoing testing and qualification to also meet the requirements for medical applications; this is an announcement, not an approval that has already been granted.
Individual requirements and procurement service
Memmert units bought from us are covered for three years from delivery: the first 12 months are followed by a 24-month warranty under Memmert’s terms, handled through us. Your statutory rights remain unaffected. Our procurement service can assist you with additional stainless steel perforated shelves (options K7, T6, K4 or C2), a stacking set for placing two ICO240 units on top of one another, or a bespoke calibration. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.