Thermal shelf made of stainless steel, material 1.4404 (ASTM 316 L)
For particularly corrosive materials
Integrated large-area heating, Pt100 sensors with 4-wire measurement
Shelf-specific overtemperature protection
Suitable for 1 Memmert model in size 101
Image for illustration only
ⓘ This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.
Product information "Memmert stainless steel 1.4404 thermal shelf B00735 for vacuum drying oven VO101"
For the VO101 vacuum drying oven, the thermal shelf B00735 made of stainless steel, material 1.4404 (ASTM 316 L), is available, intended for particularly corrosive materials. It serves as an additional heated shelf in the interior. Memmert specifies a maximum load of 20 kg for one thermal shelf.
It has integrated large-area heating with on-site sensors (Pt100, 4-wire measurement) and a shelf-specific overtemperature protection (Multi-Level-Overtemperature-Control). According to Memmert, a calibration certificate is only possible when ordering a new unit. The anodised aluminium thermal shelf is also available (B00744). The image is for illustration only.
Typical applications
Typical uses of the VO101 vacuum drying oven:
Drying larger quantities of powder or granules in vacuum cycles
Drying of printed circuit boards and electronic components
Vacuum drying of watches, books and injection moulds
1 thermal shelf made of stainless steel, material 1.4404, with integrated large-area heating
Individual requirements & procurement service
For the aluminium thermal shelf, for further accessories for the VO101 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.
With 101 litres of internal volume, the VO101 is the largest version of the Memmert VO series. The interior measures 545 x 465 x 400 mm and the housing 710 x 767 x 550 mm, plus 38 mm for the door handle. The oven weighs approx. 110 kg net. The temperature can be set from +20 to +200 °C, and the pressure digitally from 5 to 1,100 mbar.The large interior and its load limitsThe interior is welded tight and made of stainless steel 1.4404. A removable lining of the same steel with support rails, tilt protection and ceiling lining against ventilation turbulence sits inside. The unit may be loaded with 60 kg in total, and each of the maximum 2 shelves with 20 kg.An aluminium thermal shelf (material 3.3547) with integrated large-area heating is part of the scope of delivery. Two connections in the rear wall (1st and 3rd level) accept thermal shelves. Each shelf has its own MLC control and a Pt100 sensor in 4-wire measurement. The Premium module T5 includes an additional thermal shelf from the factory as well as further connections. As accessories, further shelves made of anodised aluminium (B00744) or stainless steel 1.4404 (B00735) are available.Vacuum cycles for larger quantitiesThe applications of the series include drying larger quantities of powder or granules with vacuum cycles. Temperature, pressure and program runtime are settable, and the digital pressure control works in the range 5 to 1,100 mbar. The permissible ultimate vacuum is 0.01 mbar, and the leak rate is 0.01 bar/h at most. A programmable, digitally controlled air inlet ventilates the chamber, and the pipework in the suction and ventilation area is made of material 1.4571 (ASTM 316 Ti).Pump, pump module and base frameVacuum pump and accessories for connection are not in the scope of delivery. The oven has a small flange DN16 for extraction and a gas inlet with fresh air supply. The chemically resistant 4-head diaphragm pump E07509 with approx. 50 Nl/min (3.0 m³/h) and 230 V is available for selection. It is switched ON and OFF via a signal output, and the oven controls its speed and the flushing cycles of the diaphragm on demand. Signal cable B39410 and hose B04026 with 3 m each are also mandatory. When a pump module with built-in pump (PMP101) is ordered, both are not needed, and the module without pump is called PM101. Oven and pump module form a stacked unit of 1,650 mm height with the base frame B63507.Operation, documentation and alarmTwo TFT colour graphic displays form the TwinDISPLAY, and the language can be selected from nine. The countdown clock covers 1 minute to 99 days, and SetpointWAIT starts the runtime only when the setpoint temperature has been reached. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. Programs are created and managed with AtmoCONTROL and transferred via Ethernet LAN or USB, and the program sequence is saved in the event of a power failure. For FDA requirements under 21 CFR Part 11, the licence FDAQ1 for AtmoCONTROL FDA is available as an accessory. As a factory option there is the current interface V3, which outputs the actual temperature value from 0 to 210 °C as 4 to 20 mA (only with T5).Safety technologyThe heating is switched off by the mechanical temperature limiter of protection class 1 according to DIN 12880 at approximately 10 °C above the maximum oven temperature. ASF, the AutoSAFETY monitoring, keeps a freely selectable interval to the setpoint, alarms visually and acoustically when fallen below or exceeded, and switches the heating off when exceeded. The self-diagnosis system checks the temperature control. The full-view glass door consists of spring-mounted 15 mm safety glass on the inside and a splinter-protection pane on the outside.For installation, 15 cm distance to the rear wall, 20 cm to the ceiling and 8 cm at the sides apply, with an environment of +5 to +40 °C at a maximum of 80 % relative humidity without condensation. The oven is transported upright.Selection guide: when a smaller VO is enoughThe VO49 has the same temperature and pressure range, an interior of 385 x 385 x 330 mm and approx. 83 kg net weight. With 60 kg unit load and 20 kg per shelf, both units are equal in load capacity. The interior therefore decides above all: if the material to be dried fits in 385 x 385 x 330 mm, the smaller oven is enough. Only when width, height or depth go beyond that does the VO101 with 545 x 465 x 400 mm become interesting.Typical applicationsThe VO101 is used for vacuum drying. Typical materials to be dried are food, cosmetics, granules, watches, books, printed circuit boards, electronic components and injection moulds, as well as larger quantities of powder or granules.Drying larger quantities of powder or granules with vacuum cyclesVacuum drying of food and cosmeticsDrying printed circuit boards and electronic componentsDrying watches, books and injection mouldsTechnical detailsInternal volume101 lInternal dimensions (W x H x D)545 x 465 x 400 mmExternal dimensions (W x H x D)710 x 767 x 550 mm (depth plus 38 mm door handle)Weight netapprox. 110 kgWeight gross incl. cartonapprox. 135 kgCarton dimensions (W x H x D)820 x 970 x 670 mmSetting temperature range+20 to +200 °CWorking temperature rangemin. 5 °C above room temperature to +200 °CTemperature setting accuracy0.1 °C up to 99.9 °C setpoint temperature, 0.5 °C from 100 °CTemperature sensorPt100, 4-wire measurement, separate for each thermal shelfVacuum range5 to 1,100 mbar, digital pressure controlPermissible ultimate vacuum0.01 mbarMaximum leak rate0.01 bar/hVacuum connectionSmall flange DN16, gas inlet with fresh air supplyThermal shelf connections2 in the rear wall (1st and 3rd level)Thermal shelves in scope of delivery1Shelves maximum2Max. load per shelf20 kgMax. load unit60 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayTimerdigital countdown clock, 1 minute to 99 daysInterfacesEthernet LAN, USBConnection voltage230 V, 50/60 HzPermissible ambient temperature+5 to +40 °CPermissible humiditymax. 80 % rel., non-condensingOvervoltage category / pollution degreeII / 2MarkingsCE, VDE, cMETusOther sizes in the seriesThe VO series consists of three sizes, and the VO101 is the largest:ModelInternal volumeSetting temperaturePressure rangeVO2929 l+20 to +200 °C5 to 1,100 mbarVO4949 l+20 to +200 °C5 to 1,100 mbarVO101 (this page)101 l+20 to +200 °C5 to 1,100 mbarScope of delivery1x Memmert Vacuum drying oven VO1011 thermal shelf made of aluminium (material 3.3547) with integrated large-area heatingFactory calibration certificate for +160 °C at 20 mbar pressure for every supplied thermal shelfFull-view glass door with spring-mounted 15 mm thick safety glass on the inside and splinter-protection pane on the outsideRegulatory informationThe unit is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.Individual requirements and procurement serviceAvailable as factory options are the Premium module T5, the current interfaces V3 and V6, the potential-free contact H6 and MobileALERT (C3 by SMS for every message, C4 for temperature and vacuum alarm). On the accessories side there are pump E07509 with signal cable and hose, the pump modules PM101 and PMP101, the base frame B63507, further thermal shelves, interface accessories, user ID stick and FDAQ1. In addition, factory calibration, IQ/OQ documents, on-site qualification, short training, maintenance and a maintenance contract (minimum term 3 years) can be ordered. How oven, pump and options fit together for your process is something we clarify with you case by case.