Skip to main content Skip to search Skip to main navigation

Memmert universal oven UF450mplus, 449 l, +20 to +300 °C, TwinDISPLAY, medical device class I

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert universal oven UF450mplus, 449 l, +20 to +300 °C, TwinDISPLAY, medical device class I"

The Memmert UF450mplus universal oven is not a laboratory drying oven for general use, but a Class I medical device in accordance with Regulation (EU) 2017/745, intended for the heating and keeping warm of fango, silicate and APS packs in physiotherapy. Technically, it is based on the same housing as the UF450plus laboratory/industrial cabinet, with an internal volume of 449 litres, a temperature range of 20 to 300 °C, TwinDISPLAY with two redundant Pt100 sensors, HeatBALANCE and AutoSAFETY; however, it is intended for medical use rather than general laboratory and industrial applications.

Forced air circulation with redundant temperature measurement for physiotherapy

The UF450mplus’s air turbine, which is electronically controllable in 10 % increments, actively distributes heat throughout the interior and achieves a working temperature range from at least 10 °C above room temperature up to 300 °C. Two DIN Class A Pt100 sensors in a 4-wire configuration monitor each other; if one fails, the second automatically takes over its function. The setting accuracy is 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards, which is important for the uniform heating of pack material to the temperature intended for use on the patient. Preheated fresh air is introduced via an electronically adjustable exhaust air flap.

ControlCOCKPIT TwinDISPLAY: HeatBALANCE and AutoSAFETY

The UF450mplus is controlled via the ControlCOCKPIT TwinDISPLAY, which features two high-resolution TFT colour graphic displays. The HeatBALANCE function allows fine-tuning of the heat output distribution between the upper and lower heating groups from -50 to +50 %. AutoSAFETY also monitors over- and under-temperature conditions, automatically tracks the setpoint within a freely selectable tolerance range and triggers visual and audible alarms in the event of a deviation; if the setpoint is exceeded, the heating system switches off, an important safeguard when preparing pack material for use on patients. Programmes are programmed, managed and transferred via the Ethernet interface or USB port using the AtmoCONTROL software.

Capacity and connections of the Memmert UF450mplus universal oven

The interior measures 1,040 x 720 x 600 mm and accommodates 2 electropolished stainless steel grid shelves as standard; up to 8 shelves are possible in total. A total load of up to 300 kg and up to 30 kg per shelf are permitted, sufficient for several batch loads to be processed in parallel. The external dimensions of the cabinet are 1,224 x 1,247 x 784 mm, with a net weight of approximately 161 kg. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The UF450mplus is connected to a 400 V three-phase supply and 3 x 230 V without a neutral conductor at 50/60 Hz and has a power consumption of approximately 5,800 W; it is mounted on castors and can be moved and locked in place.

Class I medical device: Intended use and classification

The UF450mplus is classified as a Class I medical device in accordance with Regulation (EU) 2017/745, with the intended purpose of heating and maintaining the temperature of fango, silicate and APS packs in physiotherapy. This classification distinguishes it fundamentally from the technically identical laboratory and industrial unit, the Memmert UF450plus universal oven, which is intended for drying, tempering and material testing, but has no medical intended use. The mplus model described here is intended for a physiotherapy practice, not the general-purpose laboratory unit.

Difference between physiotherapy device and laboratory/industrial cabinet

Anyone looking for a unit for drying, tempering or material testing processes in a laboratory or industrial setting should consider the Memmert UF450plus universal oven; it is technically largely identical but does not have a medical intended purpose. The UF450mplus described here is intended exclusively for the physiotherapy application specified in its intended use. The units are indistinguishable in appearance.

Safety according to DIN 12880, enhanced by AutoSAFETY

In addition to the adjustable electronic temperature monitoring and AutoSAFETY, the UF450mplus features a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature reaches approximately 20 °C above the maximum cabinet temperature. The display also allows the user to select either an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2. An integrated self-diagnostic system assists with fault finding, and three freely selectable temperature values can be calibrated. According to the data sheet, the unit bears the CE, VDE and UL marks.

Installation, operation and disposal

For operation, a minimum clearance of 15 cm from the wall and a minimum clearance of 20 cm from the ceiling must be maintained; a minimum clearance of 5 cm is sufficient on the sides from the wall or an adjacent unit. Installation is permitted at altitudes of up to 2,000 m above sea level, at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the cabinet is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. Thanks to its castors, the UF450mplus can still be repositioned within these specifications at a later date, for example when treatment rooms are being redesigned. As an electrical appliance, it is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste; see Regulatory information below.

Typical applications

As a Class I medical device, the Memmert UF450mplus universal oven is intended exclusively for physiotherapeutic applications involving fango, silicate and APS packs.

  • Heating of fango packs for physiotherapy applications
  • Heating and maintaining the temperature of silicate packs
  • Heating and maintaining the temperature of APS packs
  • Physiotherapy practices, rehabilitation centres and clinics offering the relevant treatments

Which device for which intended purpose

The UF450mplus is supplied with 2 electropolished stainless steel grid shelves; the cabinet is designed to accommodate up to 8 shelves. The investment decision here is primarily a question of intended use, not of features: the UF450mplus medical device is intended for a physiotherapy facility with a specific intended use. On the other hand, anyone looking for a laboratory or industrial unit for drying, tempering or materials testing is better served by the Memmert UF450plus universal oven, which is of identical construction but is not classified as a medical device. An additional Pt100 sensor is available as an option for extra over-temperature monitoring. For continuous data logging, a USB-to-Ethernet adapter and AtmoCONTROL software licences, including the AtmoCONTROL FDA version for 21 CFR Part 11, are available. For standard-compliant applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request.

Frequently asked questions before purchase

For what purpose is the UF450mplus intended?
As a Class I medical device in accordance with (EU) 2017/745 for heating and maintaining the temperature of fango, silicate and APS packs in physiotherapy.

Can I also use the UF450mplus for laboratory drying?
Technically, it is of identical construction to the Memmert UF450plus universal oven; however, its intended use as a medical device relates exclusively to physiotherapy applications. For laboratory and industrial processes, the UF450plus is the appropriate choice.

How does the UF450mplus differ visually from the UF450plus?
Externally, there is no difference between the two models.

How is the device classified?
The UF450mplus is classified as a Class I medical device in accordance with (EU) 2017/745.

How many batches can be accommodated at the same time?
Two grid shelves are included as standard; up to 8 shelves, each with a maximum load of 30 kg, are possible, giving a total load capacity of up to 300 kg.

What is the accuracy of the temperature control?
0.1 °C up to 99.9 °C and 0.5 °C from 100 °C, measured via the two redundant DIN Class A Pt100 sensors in a 4-wire configuration.

Is the UF450mplus on castors?
Yes, it is mounted on castors and can be locked in place; despite its net weight of around 161 kg, it can be moved within the permitted installation conditions.

What over-temperature safeguards does the UF450mplus have?
The mechanical temperature limiter of protection class 1 according to DIN 12880, in combination with AutoSAFETY, switches off the heating in the event of an overtemperature of approximately 20 °C.

Technical details

Setting temperature range+20 to +300 °C
Working temperature rangeat least 10 °C above room temperature up to 300 °C
Temperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °C
Temperature sensor2x Pt100, DIN Class A, 4-wire measurement, redundant
Internal volume449 l
Internal dimensions (W x H x D)1,040 x 720 x 600 mm (depth minus 39 mm for the fan)
External dimensions of housing (W x H x D)1,224 x 1,247 x 784 mm
Net weightapprox. 161 kg
Connection400 V and 3 x 230 V without neutral conductor, 50/60 Hz, approx. 5,800 W
Maximum shelves8
Shelves included2
Maximum load capacity300 kg
Max. load per shelf30 kg
Interior materialStainless steel, 4-sided all-round heating
Casing materialTextured stainless steel, galvanised sheet steel rear panel
ControlsControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displays
Additional functionsHeatBALANCE, AutoSAFETY, visual and audible alarm
Medical device classificationClass I in accordance with Regulation (EU) 2017/745
Intended useHeating and maintaining the temperature of fango, silicate and APS packs in physiotherapy
InstallationMobile and lockable on castors
Permissible ambient temperature5 °C to 40 °C
Permissible relative humiditymax. 80 % rel., non-condensing
MarkingsCE, VDE, UL

Scope of delivery

  • 1x Memmert UF450mplus universal oven
  • Factory calibration certificate (calibration at 160 °C)
  • Fully insulated stainless steel doors with 2-point locking (compression door lock)
  • 2x stainless steel grid shelf, electropolished

Regulatory information

The unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The Memmert UF450mplus universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464. It is also classified as a Class I medical device in accordance with Regulation (EU) 2017/745; see the section on Class I medical devices above.

Installation in a wall opening

For fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29740) or without air slots (B29741). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.

Individual requirements & procurement service

For the UF450mplus, the following are available, amongst other things: an additional Pt100 sensor with overtemperature protection, drip trays, a USB-to-Ethernet adapter, and AtmoCONTROL software licences, including the AtmoCONTROL FDA version for 21 CFR Part 11. We also arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you need assistance with procurement documentation for your physiotherapy practice or with distinguishing it from the structurally identical UF450plus laboratory instrument? Through our procurement service, we will be happy to assist you with procurement and configuration.

Volume: 449 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E20182 for sizes 450 and 750
Manufacturer number: E20182

The E20182 stainless steel grid is an electropolished shelf for 42 Memmert models in sizes 450 and 750. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example UF450 or UN450.All 42 models have 2 grids as standard. The maximum number is 8 grids (size 450) and 14 grids (size 750). According to Memmert, the load per shelf is 30 kg. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating very large sample quantities or several batches in research and medicine, for example in the IF750Large-volume stability studies of several batches according to ICH Q1A in contract laboratories and pharmaceutical manufacturing, for example in the HPP750ecoHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Suitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)UN450plus2830449UF450plus2830449UF4502830449UN4502830449UF750plus21430749UF75021430749UN75021430749UN750plus21430749IN450plus2830449IN4502830449IF750plus21430749IF450plus2830449IN75021430749IF75021430749IF4502830449IN750plus21430749IF750bw21430749IF450bw2830449IPP750eco21430749IPP750ecoPlus21430749HPP750eco21430749ICH75021430749ICP4502830449ICP75021430749IN450m2830449IN450mplus2830449IF450m2830449IF450mplus2830449IN750m21430749IN750mplus21430749IF750m21430749IF750mplus21430749UN450m2830449UN450mplus2830449UF450m2830449UF450mplus2830449UN750m21430749UN750mplus21430749UF750m21430749UF750mplus21430749UF450TS2830449UF750TS21430749The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert30 kgScope of delivery1 stainless steel grid, electropolished (E20182)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €207.26
memmert boden abtropfschale
Memmert stainless steel base drip tray B04362 for sizes 450 and 750
Manufacturer number: B04362

The stainless steel base drip tray B04362 is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. It has a 15 mm rim, collects dripping liquid and, according to Memmert, can bear a maximum of 8 kg. The size corresponds to the number in the unit name, for example UF450 or UN450.According to Memmert, it can impair the spatial temperature distribution. According to Memmert, it cannot be used in conjunction with option K1, the interior modification with support rails for reinforced grids and perforated trays. The table of compatible models shows which series is available in which size. The slide-in drip tray for the same unit size is also available (B02075). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert8 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €326.80
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68518 for sizes 450 and 750
Manufacturer number: B68518

B68518 is a stainless steel perforated tray for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH, HPPeco and IFbw series in sizes 450 and 750. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example UF450 or UN450. The image is for illustration only.Memmert specifies 30 kg as the maximum load per shelf. The total load of the unit is also limited; the values are given in the unit’s data sheet. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating very large sample quantities or several batches in research and medicine, for example in the IF750Large-volume stability studies of several batches according to ICH Q1A in contract laboratories and pharmaceutical manufacturing, for example in the HPP750ecoHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Suitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IF750bw750749IF450bw450449IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelLoad per shelf according to Memmert30 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €344.00
memmert untergestell nivellierbar
Memmert levelling base frame B29753, height 500 mm, for size 450
Manufacturer number: B29753

The levelling base frame B29753 has a height of 500 mm. It is intended for Memmert U and Um universal ovens, I and Im incubators and IFbw blanket warmers in size 450. The size corresponds to the number in the unit name, for example UF450 or UN450.In total, it fits 17 models of this size. The image is for illustration only.Typical applicationsUnits of size 450 are placed on the base frame. Typical uses of these units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating large quantities of samples in research and medicine, for example in the IF450Vibration-free heat treatment of dust-sensitive materials on a large scale, for example in the UN450Suitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449IN450plus450449IN450450449IF450plus450449IF450450449IF450bw450449IN450m450449IN450mplus450449IF450m450449IF450mplus450449UN450m450449UN450mplus450449UF450m450449UF450mplus450449Technical detailsHeight500 mmScope of delivery1 levelling base frame, height 500 mmIndividual requirements & procurement serviceFor base frames for other unit sizes and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €573.62
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02075 for sizes 450 and 750
Manufacturer number: B02075

The B02075 slide-in drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750; according to Memmert, the maximum load is 8 kg. The size corresponds to the number in the unit name, for example UF450 or UN450.Memmert points out that it can impair the spatial temperature distribution. It cannot be used in conjunction with option K1, the interior modification with support rails for reinforced grids and perforated trays. The table of compatible models shows which series is available in which size. The base drip tray for the same unit size is also available (B04362). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert8 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €253.70