IKA MVP 10 basic Vacuum Pump, Oil-Free Diaphragm Pump, IP 54, 0003980000
€1,687.20
% Manufacturer's RRP: €2,109.00 20% below manufacturer's RRP
- Robust, oil-free diaphragm pump for dry applications
- Delivery rate 1.7 m³/h (28.3 l/min)
- Ultimate pressure 7 mbar without, 15 mbar with gas ballast
- Degree of protection IP 54, protected against dust and splashing water
- All parts in contact with gas made of PTFE compounds
- Compact, flat design, high ease of servicing
ⓘ This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.
Product information "IKA MVP 10 basic Vacuum Pump, Oil-Free Diaphragm Pump, IP 54, 0003980000"
The IKA MVP 10 basic is a compact, oil-free diaphragm vacuum pump for straightforward laboratory use. Without a display, without digital interfaces and without a controller, the unit concentrates on pure function: reliably generating vacuum, robustly built and easy to maintain. This makes the MVP 10 basic a pragmatic choice for workstations where a simple vacuum source is needed without control software or a process log behind it, for example as a second or third pump for less critical secondary tasks alongside a precisely controlled main setup.
Two-stage pump with solid delivery rate
The two-stage, two-cylinder diaphragm pump reaches a maximum delivery rate of 1.7 cubic metres per hour (28.3 litres per minute). The ultimate pressure is 7 mbar without gas ballast and 15 mbar with the gas ballast valve activated. The gas ballast valve is particularly helpful when moist or solvent-containing vapours arise during pumping, as it reduces condensation of these in the pump and attacking the diaphragms in the long term. The permissible inlet pressure ranges from 7 to 1,050 mbar, so the pump is suitable both for initial evacuation and for maintaining an existing vacuum.
Chemical resistance through PTFE components throughout
All parts in contact with gas are made of PTFE or PTFE compounds, which are resistant to many chemicals. Combined with the dry, oil-free design, oil changes and the disposal of waste oil are eliminated, and at the same time the risk of sample contamination by oil vapours from the pump is reduced. The flat, compact design and the construction built for durability ensure a high ease of servicing in everyday laboratory work, so that maintenance can generally be carried out quickly and without special tools.
Degree of protection IP 54 for harsh operating conditions
With degree of protection IP 54 according to DIN EN 60529, the MVP 10 basic is protected against dust and splashing water. This also makes it interesting for locations where liquids are occasionally handled or the ambient air is not dust-free, for example in pilot plants or workshop laboratories. The permissible ambient temperature is between 10 and 40 °C at a maximum permissible relative humidity of 80 %, which also allows use in rooms that are less strictly air-conditioned.
Compact format for fixed workstations
With dimensions of 245 x 155 x 320 millimetres and a weight of 11.5 kilograms, the MVP 10 basic takes up little space and can also be moved between several workstations if required. The connection is made via 10 millimetre hose nozzles on the suction and pressure side, and the speed is constant at 1,380 revolutions per minute in 50 hertz operation and 1,680 revolutions per minute at 60 hertz, without any need for manual speed control. The pump is connected to 230 volts at 50 or 60 hertz with a device power consumption of 180 watts.
Deliberate omission of display and interfaces
Unlike the VACSTAR series, the MVP 10 basic deliberately dispenses with a display, digital interfaces and a vacuum controller. This reduces not only the purchase price but also the number of potential sources of error and wearing parts that would have to be replaced in the event of service. For applications that do not require finely regulated, documented process control but simply need a reliable vacuum, this is a deliberate and sensible compromise in favour of robustness, easy maintenance and a clearly calculable purchase.
Typical applications
As a robust, easy-to-operate entry-level pump without additional electronics, the MVP 10 basic is particularly suitable for the following applications:
- Simple vacuum filtrations in the routine laboratory where a finely regulated, digitally traceable ultimate vacuum depth is not required
- Suction and evacuation in pilot plants or workshop laboratories with a rougher, less air-conditioned ambient climate
- Evacuation of desiccators and simple drying setups in routine operation
- Fixed workstations with several users where a reliable, robust vacuum source without its own user interface is sufficient
- Teaching laboratories where a robust, easy-to-explain pump with no significant operating effort is required
Technical details
| Pump type | 2-cylinder diaphragm vacuum pump, dry, two-stage |
|---|---|
| Delivery rate max. (50/60 Hz) | 1.7 m³/h (28.3 l/min) |
| Ultimate pressure without gas ballast | 7 mbar |
| Ultimate pressure with gas ballast | 15 mbar |
| Suction stages / cylinders | 2 / 2 |
| Gas ballast valve | Yes |
| Connection diameter suction/pressure side | 10 mm |
| Inlet pressure | 7 to 1,050 mbar |
| Speed (50 Hz / 60 Hz) | 1,380 rpm / 1,680 rpm |
| Sound pressure level at min. pressure | 65 dB(A) |
| Wetted material | PTFE or PTFE compounds (all parts in contact with gas) |
| Dimensions (W x H x D) | 245 x 155 x 320 mm |
| Weight | 11.5 kg |
| Permissible ambient temperature | 10 to 40 °C |
| Permissible relative humidity | max. 80 % |
| Degree of protection according to DIN EN 60529 | IP 54 |
| Voltage / frequency | 230 V, 50/60 Hz |
| Device power consumption | 180 W |
Scope of delivery
- 1 x IKA MVP 10 basic Vacuum Pump
- 1 x vacuum hose
- 1 x silencer
- 1 x Y hose connector, 8 mm
Warranty
Manufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.
Regulatory information
This device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.
Individual requirements & procurement service
Accessories and spare parts for the MVP 10 basic, such as additional hose connectors or replacement diaphragms, are available on request through our procurement service.