IKA S 65 C - G 65 M Dispersing Tool, Ø 65 mm, for T 65, 0010001666

The T 65 digital ULTRA-TURRAX is designed for the transition from the laboratory to the pilot plant, for batches of 2 to 50 litres (H₂O) with a power consumption of 2,600 watts. Unlike the smaller units in the T series, it does not run on a single-phase laboratory power supply, but requires a three-phase connection of 3 x 400 volts, which must be installed by a qualified electrician. Anyone planning this connection should take this into account at the installation stage.For the transition from laboratory to pilot plantThree different rotor-stator geometries cover a range of applications from fine dispersion to coarse pre-comminution; a plug-in coupling allows tool changes to be made on the drive without the need for additional tools. Depending on the configuration, the stainless steel dispersing tools can also be used under vacuum and overpressure, provided the relevant accessories are designed for this purpose. The speed range extends from 1,000 to 9,500 rpm with a tolerance of 3 per cent, displayed via a 7-segment LED display; an error code display assists with troubleshooting during operation.Performance data for high throughputsWith a power input of 2,600 watts and an output power of 2,200 watts, the T 65 digital significantly outperforms the smaller T 25 and T 50 models; the maximum viscosity is 5,000 mPas. Measuring 300 x 420 x 400 millimetres and weighing 35 kilograms, the unit is designed for a fixed installation rather than portable use; without tools, the noise level is 75 dB(A). The IP 54 protection rating in accordance with DIN EN 60529 is noticeably higher than the IP 20 rating of the smaller T-series units, thereby allowing use in more demanding environments; permissible ambient temperatures range from 5 to 40 degrees Celsius with up to 80 per cent relative humidity.Power connection: three-phase and to be carried out only by a qualified electricianThe mains connection is 3 x 400 volts at 50 or 60 hertz; alternatively, a 3 x 230-volt version is available. A 2.5-metre power cable is not included in the scope of delivery and must be ordered separately as an accessory, as must the SI 400 safety limit switch (ID 0003294800) with the matching SI 474 bracket (ID 0003264400). According to the manufacturer, the actual mains connection must be carried out exclusively by a qualified electrician; this is a point that should be taken into account at an early stage when planning the installation, particularly if only a single-phase connection is currently available at the intended location.Typical areas of applicationPilot plants and technical trials prior to full-scale productionHomogenisation of large batches up to 50 litresApplications requiring high power and an increased protection ratingSwitching between several rotor-stator geometries depending on the formulationSelection guide: smaller model or laboratory unitIf only a single-phase connection is available or the volume is less than 30 litres, the T 50 digital ULTRA-TURRAX is the more practical choice. For laboratory volumes up to 2 litres, the T 25 digital ULTRA-TURRAX drive unit or the T 25 digital Solution complete set are significantly better suited.Technical detailsMotor power input / output2,600 W / 2,200 WProcessable volume (H₂O)2 to 50 lMax. viscosity5,000 mPasSpeed range1,000 to 9,500 rpm, continuously variable (tolerance 3 %)Speed display7-segment LEDNoise level (without tools)75 dB(A)Process typeBatchPermissible ambient temperature range / humidity5 to 40 °C / 80 %Protection classIP 54 in accordance with DIN EN 60529Rated power3 x 400 V, 50/60 Hz, 2,600 W (additional voltage variant 3 x 230 V available; connection must be carried out by a qualified electrician)Dimensions (W x H x D)300 x 420 x 400 mmWeight35 kgScope of deliveryT 65 digital ULTRA-TURRAX drive unitRotor spannerHook spannerShaft spannerCable gland for the switch cable (2 pieces)Hexagonal angle spannerThe dispersing tool, mains cable (2.5 m) and SI 400 safety limit switch are not included in the scope of delivery and are available separately. The mains connection must only be carried out by a qualified electrician.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of end-of-life equipment can be found on our Environment and Disposal page.Warranty and Procurement ServiceThe T 65 digital is covered by IKA’s manufacturer’s warranty: 2 years, extended to 3 years if registered at ika.com/register within 90 days of purchase. LT Laborhandel’s procurement service compiles dispersing tools, stands, safety limit switches and mains cables to suit the existing drive.