Memmert stainless steel perforated tray E35158 for sizes 180 and 240

Pre-order: The ICO180 is part of the new ICO NextGen range. It is available as a pre-order. The Memmert ICO180 NextGen CO₂ incubator takes the place of the previous ICO150 in the new size range, but with an internal volume of 177 litres, it offers significantly more space than its predecessor, which had a volume of 156 litres. Those who have previously used the ICO150 for larger sample quantities will find the ICO180 offers noticeably more space, whilst occupying a comparable position between the medium-sized ICO105 and the large ICO240. A touchscreen instead of two displays Instead of the previous TwinDISPLAY with two separate TFT screens, the ICO180 NextGen displays actual and target values as well as parameter trends on a 6.86-inch IPS touchscreen with multi-touch functionality (480 x 1280 pixels). Temperature and CO₂ control The temperature can be set from +20 to +50 °C; the operating range extends from at least 5 °C above room temperature up to +50 °C, with a setting accuracy of 0.1 °C. At 37 °C, the temporal temperature fluctuation is ±0.1 K, and the spatial fluctuation is ±0.3 K. CO₂ control covers 0 to 20 % CO₂ as standard, with a setting accuracy of 0.1 % and a temporal fluctuation of ±0.2 % CO₂. Humidity and O₂ as an extension A stainless-steel water tray is supplied as standard. Option K7 extends the ICO180 to include active humidity control from 40 to 98 % rh, including a ‘rh off’ function, with a setting accuracy of 0.1 % rh, utilising a self-priming micro-dosing pump with a hot steam generator for humidification and a diaphragm pump for dehumidification. Option T6 (requires Option K7) additionally controls the oxygen concentration via nitrogen injection in the range 1 to 20 % O₂, with an accuracy of 0.1 %. Six shelves and two glass doors optional With up to 6 possible shelves, the ICO180 offers more loading flexibility than the smaller models in the series; 2 stainless steel perforated shelves are supplied as standard. Option K4 equips the interior with two glass-panelled doors instead of the solid stainless steel door, allowing a quick view inside the unit without completely altering the internal climate. An integrated battery storage unit (Option C2) keeps the display unit running without interruption in the event of a power cut, ensuring seamless documentation even during an outage. Sterilisation without removing sensors A pre-programmed cycle sterilises the interior in 60 minutes at +180 °C without the need to remove the sensors beforehand. Interior and door The deep-drawn interior is made of stainless steel grade 1.4301 (ASTM 304). The fully insulated stainless steel door closes with a 2-point compression lock and features an internal glass door; maximum load: 15 kg per shelf and 90 kg per unit. Interfaces and software The ICO180 NextGen features USB-C and Ethernet LAN. The chargeable software application myChamber LIMS is available for connection to a LIMS, whilst the connectivity package for the myChamber Monitoring App is available for permanent remote monitoring. For electronic signatures according to 21 CFR Part 11, the basic licence FDAQ1 for AtmoCONTROL FDA and myChamber Control FDA can be added. None of the three options is included as standard. Operation and connected load specifications The ICO180 NextGen is rated for 230 V, 50/60 Hz; Option X2 converts it to 115 V at no extra charge, and the power consumption is approximately 1,550 W. The textured stainless steel housing measures 748 x 793 x 689 mm (width x height x depth), plus a 50 mm allowance for the door handle; the internal dimensions are 600 x 590 x 500 mm. The net weight is 98 kg; when packed, it weighs 116 kg. Anyone wishing to stack two ICO180 units on top of one another can use a stacking kit (item no. B64732) or a mobile stacking kit with a raised base (item no. B68476). Other sizes in the ICO NextGen series In addition to the ICO180 (177 litres), we offer the ICO50 (56 litres) and the ICO105 (108 litres) for smaller batches, as well as the ICO240 (243 litres) for the highest throughput, each featuring the same operating concept. Typical applications With its large internal volume, controlled temperature and CO₂ concentration, the ICO180 NextGen is suitable for: Incubation of larger sample volumes or multiple experimental runs simultaneously Microbiological, pharmaceutical and biotechnological research with higher throughput Laboratory operations where glass doors (Option K4) allow visual monitoring without a complete change in the internal climate Stacked configuration of multiple units where floor space is limited (stacking kit accessory) Technical details Internal volume177 litres Internal dimensions (W x H x D)600 x 590 x 500 mm (depth minus 37.5 mm for the fan) Cabinet dimensions (W x H x D)748 x 793 x 689 mm (plus 50 mm door handle) Interior materialStainless steel grade 1.4301 (ASTM 304), deep-drawn Temperature setting range+20 to +50 °C Operating temperature rangeat least 5 °C above room temperature up to +50 °C Temperature accuracy0.1 °C (temporal variation at 37 °C ±0.1 K, spatial ±0.3 K) CO₂ control0 to 20 % CO₂, accuracy 0.1 %, temporal variation ±0.2 % CO₂ Humidity control (Option K7)40 to 98 % rh and rh-Off, accuracy 0.1 % rh O₂ control (Option T6, requires K7)1 to 20 % O₂, accuracy 0.1 % Control unit6.86" IPS touchscreen (480 x 1280 pixels), multi-touch DoorFully insulated stainless steel door, 2-point locking, internal glass door (optional: 2 doors with glass cut-outs, Option K4) Shelves2x stainless steel perforated shelves included in the scope of delivery, up to 6 possible Max. load90 kg total / 15 kg per shelf Installation4 adjustable feet InterfacesUSB-C, Ethernet LAN Factory calibration certificate+37 °C, 5 % CO₂ (standard; with option K7 additionally 90 % rh, with K7 and T6 additionally 10 % O₂) Voltage/Power230 V, 50/60 Hz, approx. 1,550 W (Option X2: 115 V at no extra cost) Net weight/Gross weight98 kg / 116 kg Scope of delivery 1x Memmert ICO180 NextGen CO₂ incubator (basic unit) 2x stainless steel perforated shelves 1x stainless steel water tray 1x CO₂ connection set (hose with connector and hose clamp) 1x factory calibration certificate (+37 °C, 5 % CO₂) Not included in the scope of delivery: active humidity control (Option K7), O₂ control (Option T6), glass doors (Option K4), battery storage (Option C2), stacking kits and the water canister with connection hose (only when option K7 is ordered) are additional options, as are the software licences for myChamber LIMS, the Monitoring App and FDAQ1. Regulatory information Manufacturer’s WEEE registration number (Memmert GmbH + Co. KG, Stiftung EAR): DE 66812464. The ICO180 NextGen is not a medical device. Memmert is discontinuing the separate, previous ICOmed medical device series (last order 6 November 2026); according to Memmert, the ICO NextGen is currently undergoing testing and qualification to also meet the requirements for medical applications; this is an announcement, not an approval that has already been granted. Individual requirements and procurement service Memmert units bought from us are covered for three years from delivery: the first 12 months are followed by a 24-month warranty under Memmert’s terms, handled through us. Your statutory rights remain unaffected. Our procurement service can assist you with additional stainless steel perforated shelves, the K7, T6, K4 or C2 options, a stacking kit for stacking two ICO180 units on top of one another, or a bespoke calibration. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

Pre-order: The ICO240 is part of the new ICO NextGen series. It is available as a pre-order. With an internal volume of 243 litres, the Memmert ICO240 NextGen CO₂ incubator is the largest model in the new series, offering two litres more capacity than the previous ICO240 from the 2012 generation. With up to 9 possible shelves, it is suitable for laboratories with high sample throughput or multiple users who load the same incubator simultaneously. A touchscreen display instead of two screens Instead of the previous ControlCOCKPIT TwinDISPLAY with two separate TFT screens, the ICO240 NextGen displays actual and setpoint values as well as parameter trends on a 6.86-inch IPS touchscreen with multi-touch functionality (480 x 1280 pixels). Temperature and CO₂ control The temperature can be set from +20 to +50 °C; the operating range extends from at least 5 °C above room temperature to +50 °C, with a setting accuracy of 0.1 °C. At 37 °C, the temporal temperature fluctuation is ±0.1 K, and the spatial fluctuation is ±0.3 K. CO₂ control covers 0 to 20 % CO₂ as standard, with a setting accuracy of 0.1 % and a temporal fluctuation of ±0.2 % CO₂. Humidity and O₂ as an extension A stainless-steel water tray is supplied as standard. Option K7 extends the ICO240 to include active humidity control from 40 to 98 % rh, including a ‘rh off’ function, with a setting accuracy of 0.1 % rh, utilising a self-priming micro-dosing pump with a hot steam generator for humidification and a diaphragm pump for dehumidification. Option T6 (requires Option K7) additionally controls the oxygen concentration via nitrogen injection in the range 1 to 20 % O₂, with an accuracy of 0.1 %. Nine shelves and three glass doors optional With up to 9 possible shelves, the ICO240 has the largest loading capacity in the series; 2 stainless steel perforated shelves are included as standard, with a maximum load of 15 kg per shelf and 135 kg per unit in total. Option K4 equips the interior with three glass-panelled doors instead of the solid stainless steel door, the highest number in the series for this size, which is practical when several users wish to keep an eye on different areas without having to open the entire door every time. An integrated battery storage unit (Option C2) keeps the display unit running without interruption in the event of a power cut. Sterilisation without removing sensors A pre-programmed cycle sterilises the interior in 60 minutes at +180 °C without the need to remove the sensors beforehand. This simplifies switching between different culture batches in day-to-day laboratory work. Interior and door The deep-drawn interior is made of stainless steel grade 1.4301 (ASTM 304). The fully insulated stainless steel door closes with a 2-point compression lock and features an internal glass door. Interfaces and software The ICO240 NextGen features USB-C and Ethernet LAN. The chargeable software application myChamber LIMS is available for connection to a LIMS, whilst the connectivity package for the myChamber Monitoring App is available for permanent remote monitoring. For electronic signatures according to 21 CFR Part 11, the basic licence FDAQ1 for AtmoCONTROL FDA and myChamber Control FDA can be added. None of the three options is included as standard. Operation and connected load specifications The ICO240 NextGen is rated for 230 V, 50/60 Hz; Option X2 converts it to 115 V at no extra cost; power consumption is approximately 1,750 W, the highest figure in the series. The textured stainless steel housing measures 748 x 1013 x 689 mm (width x height x depth), plus a 50 mm allowance for the door handle; the internal dimensions are 600 x 810 x 500 mm. The net weight is 113 kg; when packed, it weighs 132 kg; delivery and installation should be planned accordingly. Other sizes in the ICO NextGen series In addition to the ICO240 (243 litres), we offer the ICO50 (56 litres) and the ICO105 (108 litres) for smaller applications, as well as the ICO180 (177 litres, successor to the previous ICO150), each featuring the same operating concept and the same control parameters. Typical applications With the largest internal volume in the range, as well as controlled temperature and CO₂ concentration, the ICO240 NextGen is suitable for: High sample throughput or multiple parallel test series in a single unit Microbiological, pharmaceutical and biotechnological research requiring a large amount of space Laboratory operations with multiple users who can access specific areas via the optional glass doors (Option K4, 3 doors) Laboratory operations involving frequently changing culture batches, thanks to the integrated sterilisation function Technical details Internal volume243 litres Internal dimensions (W x H x D)600 x 810 x 500 mm (depth minus 37.5 mm for the fan) Cabinet dimensions (W x H x D)748 x 1013 x 689 mm (plus 50 mm door handle) Interior materialStainless steel grade 1.4301 (ASTM 304), deep-drawn Temperature setting range+20 to +50 °C Operating temperature rangeat least 5 °C above room temperature up to +50 °C Temperature accuracy0.1 °C (temporal variation at 37 °C ±0.1 K, spatial ±0.3 K) CO₂ control0 to 20 % CO₂, accuracy 0.1 %, temporal variation ±0.2 % CO₂ Humidity control (Option K7)40 to 98 % rh and rh-Off, accuracy 0.1 % rh O₂ control (Option T6, requires K7)1 to 20 % O₂, accuracy 0.1 % Control unit6.86" IPS touchscreen (480 x 1280 pixels), multi-touch DoorFully insulated stainless steel door, 2-point locking, internal glass door (optional: 3 doors with glass cut-outs, Option K4) Shelves2x stainless steel perforated shelves included in the scope of delivery, up to 9 possible Max. load135 kg total / 15 kg per shelf Installation4 adjustable feet InterfacesUSB-C, Ethernet LAN Factory calibration certificate+37 °C, 5 % CO₂ (standard; with option K7 additionally 90 % rh, with K7 and T6 additionally 10 % O₂) Voltage/Power230 V, 50/60 Hz, approx. 1,750 W (Option X2: 115 V at no extra charge) Net weight/Gross weight113 kg / 132 kg Scope of delivery 1x Memmert ICO240 NextGen CO₂ incubator (basic unit) 2x stainless steel perforated shelves 1x stainless steel water tray 1x CO₂ connection set (hose with connector and hose clamp) 1x factory calibration certificate (+37 °C, 5 % CO₂) Not included in the scope of delivery: active humidity control (Option K7), O₂ control (Option T6), glass doors (Option K4), battery storage (Option C2), stacking kits and the water canister with connection hose (only when option K7 is ordered) are additional options, as are the software licences for myChamber LIMS, the Monitoring App and FDAQ1. Regulatory information Manufacturer’s WEEE registration number (Memmert GmbH + Co. KG, Stiftung EAR): DE 66812464. The ICO240 NextGen is not a medical device. Memmert is discontinuing the separate, previous ICOmed medical device series (last order 6 November 2026); according to Memmert, the ICO NextGen is currently undergoing testing and qualification to also meet the requirements for medical applications; this is an announcement, not an approval that has already been granted. Individual requirements and procurement service Memmert units bought from us are covered for three years from delivery: the first 12 months are followed by a 24-month warranty under Memmert’s terms, handled through us. Your statutory rights remain unaffected. Our procurement service can assist you with additional stainless steel perforated shelves (options K7, T6, K4 or C2), a stacking set for placing two ICO240 units on top of one another, or a bespoke calibration. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert Humidity Chamber HCP240 is the largest version of the HCP series: 241 litres of internal volume, up to twelve shelves, 140 kg permissible total load. The housing measures 759 x 1,180 x 691 mm externally plus 56 mm door handle, and the interior 600 x 810 x 500 mm (depth less 35 mm for the fan). The chamber sets +18 to +90 °C and 20 to 95 % rh, optionally with rh-Off, and is controlled via the ControlCOCKPIT TwinDISPLAY.Weight, dimensions and connectionAt approx. 110 kg net weight, the HCP240 is the heaviest HCP. Connection is with 230 V and 50/60 Hz at approx. 1,840 W. Two stainless steel perforated trays are inserted from the factory, and 15 kg apply per shelf. The interior is made of stainless steel 1.4301 (ASTM 304). A heated inner glass door sits behind the fully insulated stainless steel door, which closes with 2-point locking. In the rear wall (centre left), a humidity-tight silicone feedthrough with 40 mm inner diameter leads supply lines into the interior, and a silicone plug closes it.Humidification and dehumidificationHumidification is from an external container with a self-priming pump. A water canister and the connection hose are included in the scope of delivery. An integrated germ barrier uses hot steam generation, and a sterile filter takes care of dehumidification. The water must be demineralised or fully deionised, with 5 to 10 µS/cm and a pH value of 5 to 7. Setting accuracy: 0.5 % rh for humidity, 0.1 °C for temperature. To avoid condensate formation, door and rear wall are additionally heated, in addition to the all-round heating on six sides. We will tell you about further options for the water supply on request.Programs, calibration values and languagesAtmoCONTROL writes and transfers programs via Ethernet or USB. Three freely selectable values each for temperature and humidity can be calibrated. The countdown clock is set between 1 minute and 99 days, and SetpointWAIT begins the process time only at the setpoint temperature. Temperature appears in Celsius or Fahrenheit, and there are also time zones and the changeover between summer and winter time. Operation is possible in nine languages, including German, English, Spanish, French and Italian. After a power failure, the saved program sequence is available.Alarm and self-diagnosisThe Pt100 sensors (two of them, DIN class A, 4-wire measurement) check each other, and if one sensor fails, the other continues to work. The AutoSAFETY monitoring "ASF" follows the setpoint at an interval that can be freely selected. Exceeding and falling below trigger a visual and acoustic alarm, and when exceeded the heating also switches off. The self-diagnosis system serves to find faults in temperature and humidity control. Permissible are 10 to 30 °C room temperature at a maximum of 70 % rel. humidity without condensation and an installation altitude up to 2,000 m above sea level. Also to be observed are at least 15 cm distance to the rear wall, 20 cm to the ceiling and 5 cm at the sides.Placement in the HCP seriesThe next smaller HCP150 has 156 l, ten shelves and 120 kg total load. The HCP240 is above it with 241 l, twelve shelves and 140 kg. For more volume or operation near or below room temperature, the ICH260 climate chamber is the alternative from a different series: 256 l, setting temperature range -10 to +60 °C, humidity 10 to 80 % rh in the range +10 to +60 °C. The HCP240, by contrast, reaches up to +90 °C and up to 95 % rh.Typical applicationsThe HCP series is intended for the following areas of use:Environmental testingEnvironmental simulationsAccelerated lifetime tests85/85 tests according to IEC 60068-2-67 and IEC 60068-2-78Technical detailsInternal volume241 lInternal dimensions (W x H x D)600 x 810 x 500 mm (D less 35 mm for fan)External dimensions (W x H x D)759 x 1,180 x 691 mm (D plus 56 mm door handle)Weight (net)approx. 110 kgShelvesup to 12, 2 perforated trays in scope of deliveryLoad capacity140 kg total, 15 kg per shelfTemperature range (setting)+18 to +90 °CTemperature range (working range)7 °C above room temperature to +90 °CTemperature accuracy (setting)0.1 °CHumidity range (setting)20 to 95 % rh and rh-OffHumidity accuracy (setting)0.5 % rhSensors2x Pt100, DIN class A, 4-wire measurement, redundantControlTwinDISPLAY, PID microprocessor controller with 2 TFT colour graphic displaysWaterdemineralised or fully deionised, 5 to 10 µS/cm, pH 5 to 7Voltage and power230 V, 50/60 Hz, approx. 1,840 WData connectionsEthernet LAN, USBOperating environment10 to 30 °C, max. 70 % rel., non-condensing, up to 2,000 m above sea levelMarkingCE, VDE GS, cMETusOther sizes in the seriesThe HCP series comprises four sizes, and the HCP240 is at the upper end:ModelInternal volumeSetting temperatureHumidity rangeHCP5056 l+18 to +90 °C20 to 95 % rhHCP105107 l+18 to +90 °C20 to 95 % rhHCP150156 l+18 to +90 °C20 to 95 % rhHCP240 (this page)241 l+18 to +90 °C20 to 95 % rhScope of deliveryMemmert Humidity Chamber HCP240Stainless steel perforated tray, 2 piecesFactory calibration certificate for 60 °C at 75 % rh (measuring room centre of usable space)Heated inner glass doorFully insulated stainless steel door, 2-point locking (compression door lock)Silicone feedthrough, humidity-tight, 40 mm inner diameter, rear wall, centre leftWater canister with connection hoseRegulatory informationThe unit is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.Individual requirements and procurement serviceFor the HCP240, factory options are available that are specified when ordering, as well as accessories and calibration and qualification services. We coordinate the current scope with Memmert on request. Tell us how you want to use the chamber, and we will advise you personally and prepare a non-binding quotation. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.