IKA S 65 KG - HH - G 65 F Dispersing Tool, Ø 65 mm, Suitable for Vacuum Use, 0010010768
€5,786.45
% Manufacturer's RRP: €6,091.00 5% below manufacturer's RRP
- Working volume 2 to 30 l, stator 65 mm, rotor 58 mm
- Vacuum down to 1 mbar, pressure up to 6 bar
- Final particle size 5 to 20 µm (suspensions), 1 to 10 µm (emulsions)
- Immersion depth 80 to 450 mm with an installation length of 510 mm
- Ball-bearing-mounted shaft with carbide mechanical seal
- Suitable for solvents, FDA-compliant, sterilisable using all methods
Product information "IKA S 65 KG - HH - G 65 F Dispersing Tool, Ø 65 mm, Suitable for Vacuum Use, 0010010768"
The S 65 KG - HH - G 65 F (0010010768), with a 65 mm stator and a 58 mm rotor, processes batches ranging from 2 to 30 l. The shaft is mounted on ball bearings; the mechanical seal consists of carbide against carbide. IKA specifies the T 65 digital as the drive unit.
Vacuum and pressure
The unit is designed for vacuum down to 1 mbar and pressure up to 6 bar. Materials in contact with the product include FFPM, tungsten carbide (WC) and AISI 316L. It is suitable for solvents, with a pH range of 2 to 13. The maximum operating temperature is 170 °C, and it may be sterilised using any method. FDA compliance is stated.
Geometry and Final Particle Size
The gap between the rotor and stator is 0.5 mm wide, and the peripheral speed is a maximum of 28.8 m/s. The final fineness is 5 to 20 µm for suspensions and 1 to 10 µm for emulsions. The immersion depth ranges from 80 to 450 mm, and the installation length is 510 mm. The tool measures 65 x 550 x 65 mm and weighs 4.45 kg; by comparison, the S 50 KG - HH - G 45 G weighs 0.552 kg.
Siblings in the S 65 series
The S 65 KG - HH - G 65 M has the same design, processes 2 to 40 l and specifies 20 to 50 µm (suspensions) and 5 to 15 µm (emulsions). The S 65 KG - HH - G 65 G has a 53 mm rotor and processes 2 to 50 l. The S 65 KD - G 65 F is available with a PTFE seal and FFKM O-ring instead of a mechanical seal, and with a vacuum down to 100 mbar.
Typical applications
- Dispersing and emulsifying in batches of 2 to 30 l
- Operations under vacuum down to 1 mbar
- Processes at pressures up to 6 bar
- Batches involving solvents
- Applications where FDA compliance is required
Technical details
| Working range (H2O) | 2 to 30 l |
| Stator diameter | 65 mm |
| Rotor diameter | 58 mm |
| Stator/rotor gap width | 0.5 mm |
| Max. circumferential speed | 28.8 m/s |
| Immersion depth | 80 to 450 mm |
| Installation length | 510 mm |
| Bearings and seals | Ball bearing, mechanical seal (carbide/carbide) |
| Materials in contact with the product | FFPM, WC / AISI 316L |
| pH range | 2 to 13 |
| Suitable for solvents | Yes |
| Max. operating temperature | 170 °C |
| Sterilisability | All methods |
| Vacuum | 1 mbar |
| Max. pressure | 6 bar |
| Final fineness of suspensions | 5 to 20 µm |
| Final fineness of emulsions | 1 to 10 µm |
| FDA compliance | Yes |
| Dimensions (W x H x D) | 65 x 550 x 65 mm |
| Weight | 4.45 kg |
Scope of delivery
- 1 x IKA S 65 KG - HH - G 65 F dispersing tool (single tool)
- The T 65 digital drive is not included in the Scope of delivery.
Individual requirements and procurement service
LT Laborhandel can source the T 65 digital drive and other tools on request. The procurement service assists in selecting the appropriate geometry.
Fits
The T 65 digital ULTRA-TURRAX is designed for the transition from the laboratory to the pilot plant, for batches of 2 to 50 litres (H₂O) with a power consumption of 2,600 watts. Unlike the smaller units in the T series, it does not run on a single-phase laboratory power supply, but requires a three-phase connection of 3 x 400 volts, which must be installed by a qualified electrician. Anyone planning this connection should take this into account at the installation stage.For the transition from laboratory to pilot plantThree different rotor-stator geometries cover a range of applications from fine dispersion to coarse pre-comminution; a plug-in coupling allows tool changes to be made on the drive without the need for additional tools. Depending on the configuration, the stainless steel dispersing tools can also be used under vacuum and overpressure, provided the relevant accessories are designed for this purpose. The speed range extends from 1,000 to 9,500 rpm with a tolerance of 3 per cent, displayed via a 7-segment LED display; an error code display assists with troubleshooting during operation.Performance data for high throughputsWith a power input of 2,600 watts and an output power of 2,200 watts, the T 65 digital significantly outperforms the smaller T 25 and T 50 models; the maximum viscosity is 5,000 mPas. Measuring 300 x 420 x 400 millimetres and weighing 35 kilograms, the unit is designed for a fixed installation rather than portable use; without tools, the noise level is 75 dB(A). The IP 54 protection rating in accordance with DIN EN 60529 is noticeably higher than the IP 20 rating of the smaller T-series units, thereby allowing use in more demanding environments; permissible ambient temperatures range from 5 to 40 degrees Celsius with up to 80 per cent relative humidity.Power connection: three-phase and to be carried out only by a qualified electricianThe mains connection is 3 x 400 volts at 50 or 60 hertz; alternatively, a 3 x 230-volt version is available. A 2.5-metre power cable is not included in the scope of delivery and must be ordered separately as an accessory, as must the SI 400 safety limit switch (ID 0003294800) with the matching SI 474 bracket (ID 0003264400). According to the manufacturer, the actual mains connection must be carried out exclusively by a qualified electrician; this is a point that should be taken into account at an early stage when planning the installation, particularly if only a single-phase connection is currently available at the intended location.Typical areas of applicationPilot plants and technical trials prior to full-scale productionHomogenisation of large batches up to 50 litresApplications requiring high power and an increased protection ratingSwitching between several rotor-stator geometries depending on the formulationSelection guide: smaller model or laboratory unitIf only a single-phase connection is available or the volume is less than 30 litres, the T 50 digital ULTRA-TURRAX is the more practical choice. For laboratory volumes up to 2 litres, the T 25 digital ULTRA-TURRAX drive unit or the T 25 digital Solution complete set are significantly better suited.Technical detailsMotor power input / output2,600 W / 2,200 WProcessable volume (H₂O)2 to 50 lMax. viscosity5,000 mPasSpeed range1,000 to 9,500 rpm, continuously variable (tolerance 3 %)Speed display7-segment LEDNoise level (without tools)75 dB(A)Process typeBatchPermissible ambient temperature range / humidity5 to 40 °C / 80 %Protection classIP 54 in accordance with DIN EN 60529Rated power3 x 400 V, 50/60 Hz, 2,600 W (additional voltage variant 3 x 230 V available; connection must be carried out by a qualified electrician)Dimensions (W x H x D)300 x 420 x 400 mmWeight35 kgScope of deliveryT 65 digital ULTRA-TURRAX drive unitRotor spannerHook spannerShaft spannerCable gland for the switch cable (2 pieces)Hexagonal angle spannerThe dispersing tool, mains cable (2.5 m) and SI 400 safety limit switch are not included in the scope of delivery and are available separately. The mains connection must only be carried out by a qualified electrician.Regulatory informationThis device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of end-of-life equipment can be found on our Environment and Disposal page.Warranty and Procurement ServiceThe T 65 digital is covered by IKA’s manufacturer’s warranty: 2 years, extended to 3 years if registered at ika.com/register within 90 days of purchase. LT Laborhandel’s procurement service compiles dispersing tools, stands, safety limit switches and mains cables to suit the existing drive.