Skip to main content Skip to search Skip to main navigation

Memmert Compressor-Cooled incubator ICP450, 449 l, -12 to +60 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert Compressor-Cooled incubator ICP450, 449 l, -12 to +60 °C, TwinDISPLAY"

With 449 litres, the Memmert Compressor-Cooled incubator ICP450 is the third of four ICP sizes and differs from the smaller models by its wide interior of 1,040 × 720 × 600 mm (W×H×D). 30 kg are allowed per shelf and 200 kg for the whole unit. The setting temperature range extends from -12 to +60 °C, R290 propane serves as refrigerant, and operation is via a TwinDISPLAY. Externally the chamber measures 1,224 × 1,467 × 784 mm, and the door handle adds 56 mm.

Wide interior, up to eight shelves

Two electropolished stainless steel grid shelves are part of the series, and a maximum of 8 shelves are possible. With 30 kg per shelf, each level carries more than on the ICP110 and ICP260 with 20 kg each. For even higher loads there is the factory option K1: it mounts support rails in the working chamber for reinforced stainless steel grid shelves or reinforced perforated trays that can bear up to 60 kg. The limit of 200 kg per unit remains in place. For the drip trays there are variants with and without K1.

Cooling and heating via compressor and air jacket

The CFC-free cooling and heating system with R290 propane has an automatic defrost. An air jacket controls the temperature of the interior all round, and the thermal jacket is separated from the interior, so that no evaporators dry out the material. The unit is not suitable for permanent storage at sub-zero temperatures, and in continuous operation the glass door can ice up. Temperatures down to -12 °C can be set, and the setting accuracy is 0.1 °C.

Control, timer and programming

The ControlCOCKPIT works with an adaptive digital PID microprocessor controller and two TFT colour graphic displays. The digital countdown clock is set between 1 minute and 99 days, and SetpointWAIT postpones the start of the process time until the setpoint temperature is reached. On the unit, temperature unit, circulating air motor speed, program runtime and time zones can be set, and the calibration records three temperature values. Programs created with AtmoCONTROL are transferred via Ethernet or USB port. The program sequence is saved in the event of a power failure.

Protection against deviations

Two Pt100 sensors of DIN class A in 4-wire measurement monitor each other. The mechanical temperature limiter TB (protection class 1, DIN 12880) interrupts the heating at about 10 °C above the maximum chamber temperature. TWW (protection class 3.3) and TWB (protection class 2) are available for selection on the display. The AutoSAFETY protection ASF follows the setpoint at a freely selectable interval and reports deviations upwards or downwards by alarm, visually and acoustically. In the event of a fault, the self-diagnosis system helps.

Selection guide compared with ICP260 and ICP750

The ICP260 has 256 litres, 640 × 800 × 500 mm inside and up to 9 shelves with 20 kg each. The ICP450 is wider and deeper inside, but lower (720 instead of 800 mm), and allows only 8 shelves. Anyone who needs space in height and up to 14 shelves takes the ICP750 with 749 litres and 1,200 mm internal height at the same width and depth. Anyone who also needs to control air humidity will find 256 litres with active humidification and dehumidification from 10 to 80 % rh in the ICH260 climate chamber. Its setting temperature range begins at -10 °C, and with humidity it works from +10 to +60 °C.

Typical applications

  • Incubating, culturing and cooling for biology, zoology, pharmaceuticals and food
  • Incubating, drying and storing (not permanently at sub-zero temperatures)
  • Ramp operation with rapid temperature changes when incubating, culturing or storing

Technical details

Interior volume449 l
Internal dimensions (W×H×D)1,040 × 720 × 600 mm (depth less 33 mm for the fan)
External dimensions (W×H×D)1,224 × 1,467 × 784 mm (depth plus 56 mm door handle)
Setting temperature range-12 to +60 °C (not suitable for permanent storage at sub-zero temperatures, in continuous operation the glass door can ice up)
Setting accuracy temperature0.1 °C
Temperature sensor2 Pt100 DIN class A, 4-wire measurement, mutual monitoring and function takeover in the event of a fault
Cooling/heating systemCompressor, CFC-free, refrigerant R290 propane, automatic defrost
ControlControlCOCKPIT TwinDISPLAY, adaptive digital PID microprocessor controller with 2 TFT colour graphic displays
TimerDigital countdown clock with target time indication, 1 min to 99 days, SetpointWAIT function
Temperature monitoringMechanical temperature limiter TB protection class 1 (DIN 12880), adjustable temperature monitor TWW protection class 3.3 or adjustable temperature limiter TWB protection class 2, AutoSAFETY ASF
InterfacesEthernet and USB port
DoorFully insulated stainless steel doors with 2-point locking (compression door lock), inner glass doors
Shelves standard/max.2 / 8
Max. load200 kg per unit / 30 kg per shelf
InstallationMobile and lockable on castors, distance to the wall at the back at least 15 cm, to the ceiling 20 cm, at the sides to wall or neighbouring unit at least 5 cm
Ambient conditionsHumidity max. 70 % non-condensing, max. 2,000 m above sea level, overvoltage category II, pollution degree 2
Voltage/power consumption230 V, 50/60 Hz, approx. 1,200 W; 115 V, 50/60 Hz (factory option X2), approx. 1,200 W
Net weight/gross weightapprox. 217 kg / approx. 282 kg (carton 1,330 × 1,700 × 1,050 mm)

Other sizes in the series

The ICP450 belongs to a series with four sizes between 108 and 749 litres:

ModelInternal volumeSetting temperatureDisplay
ICP110108 l-12 to +60 °CTwinDISPLAY
ICP260256 l-12 to +60 °CTwinDISPLAY
ICP450 (this page)449 l-12 to +60 °CTwinDISPLAY
ICP750749 l-12 to +60 °CTwinDISPLAY

Scope of delivery

  • 1× Memmert Compressor-Cooled incubator ICP450
  • Fully insulated stainless steel doors with 2-point locking (compression door lock)
  • Inner glass doors
  • 2× stainless steel grid shelf, electropolished
  • Factory calibration certificate at +10 °C and +37 °C

Regulatory information

The unit is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.

The cooling system works with the refrigerant R290 (propane).

Individual requirements and procurement service

Besides K1, these factory options are available when ordering: 115 V (X2), interior socket (R3), cable feedthroughs with 23 mm inner diameter (F0, F1, F3), silicone feedthrough with 40 mm (F7), 4-20 mA interfaces (V3, V6), fan monitoring with heating shutdown (V4), lockable door (B6), alarm contact (H6), door-open detection (V5) and MobileALERT (C3, requires H6). We discuss prerequisites and combination limits when you enquire.

Accessories include stainless steel grid shelves, reinforced grid shelves and perforated trays (up to 60 kg, with option K1), drip trays for shelf and floor, the USB-Ethernet adapter, a 5 m Ethernet cable, the USB user ID stick and the FDA licence FDAQ1. Calibration at the factory or on site, DAkkS calibration, IQ/OQ, qualification, training and maintenance can also be ordered. We take your enquiry on configuration and spare parts.

Volume: 449 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E20182 for sizes 450 and 750
Manufacturer number: E20182

The E20182 stainless steel grid is an electropolished shelf for 42 Memmert models in sizes 450 and 750. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example UF450 or UN450.All 42 models have 2 grids as standard. The maximum number is 8 grids (size 450) and 14 grids (size 750). According to Memmert, the load per shelf is 30 kg. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating very large sample quantities or several batches in research and medicine, for example in the IF750Large-volume stability studies of several batches according to ICH Q1A in contract laboratories and pharmaceutical manufacturing, for example in the HPP750ecoHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Suitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)UN450plus2830449UF450plus2830449UF4502830449UN4502830449UF750plus21430749UF75021430749UN75021430749UN750plus21430749IN450plus2830449IN4502830449IF750plus21430749IF450plus2830449IN75021430749IF75021430749IF4502830449IN750plus21430749IF750bw21430749IF450bw2830449IPP750eco21430749IPP750ecoPlus21430749HPP750eco21430749ICH75021430749ICP4502830449ICP75021430749IN450m2830449IN450mplus2830449IF450m2830449IF450mplus2830449IN750m21430749IN750mplus21430749IF750m21430749IF750mplus21430749UN450m2830449UN450mplus2830449UF450m2830449UF450mplus2830449UN750m21430749UN750mplus21430749UF750m21430749UF750mplus21430749UF450TS2830449UF750TS21430749The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert30 kgScope of delivery1 stainless steel grid, electropolished (E20182)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €207.26
memmert boden abtropfschale
Memmert stainless steel base drip tray B04362 for sizes 450 and 750
Manufacturer number: B04362

The stainless steel base drip tray B04362 is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. It has a 15 mm rim, collects dripping liquid and, according to Memmert, can bear a maximum of 8 kg. The size corresponds to the number in the unit name, for example UF450 or UN450.According to Memmert, it can impair the spatial temperature distribution. According to Memmert, it cannot be used in conjunction with option K1, the interior modification with support rails for reinforced grids and perforated trays. The table of compatible models shows which series is available in which size. The slide-in drip tray for the same unit size is also available (B02075). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert8 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €326.80
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68518 for sizes 450 and 750
Manufacturer number: B68518

B68518 is a stainless steel perforated tray for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH, HPPeco and IFbw series in sizes 450 and 750. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example UF450 or UN450. The image is for illustration only.Memmert specifies 30 kg as the maximum load per shelf. The total load of the unit is also limited; the values are given in the unit’s data sheet. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating very large sample quantities or several batches in research and medicine, for example in the IF750Large-volume stability studies of several batches according to ICH Q1A in contract laboratories and pharmaceutical manufacturing, for example in the HPP750ecoHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Suitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IF750bw750749IF450bw450449IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelLoad per shelf according to Memmert30 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €344.00
Memmert stainless steel slide-in drip tray B32763 for sizes 450 and 750, option K1 required
Manufacturer number: B32763

Only for units with factory option K1. The drip tray only fits units that were equipped with option K1 at the factory, a modification of the interior with support rails for reinforced grids and perforated trays. This option is available for sizes 450 and 750 and only ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request. The size corresponds to the number in the unit name, for example IF450 or IN450.The B32763 slide-in drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is supplied with guide rails and fixing screws and is the version for units with option K1. For units without option K1, the B02075 slide-in drip tray is also available.According to Memmert, it can impair the spatial temperature distribution. It is intended for Memmert units in the U, UF TS, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)IF450450449IN450450449IF450plus450449IN450plus450449ICP450450449UF450450449UN450450449UF450plus450449UN450plus450449UF450TS450449HPP750eco750749IF750750749IN750750749IF750plus750749IN750plus750749ICH750750749ICP750750749IPP750eco750749IPP750ecoplus750749UF750750749UN750750749UF750plus750749UN750plus750749UF750TS750749Technical detailsMaterialStainless steelRim15 mmRequired optionK1 (ex works only)Scope of delivery1 stainless steel slide-in drip tray, 15 mm rim, with guide rails and fixing screwsIndividual requirements & procurement serviceFor the drip tray without option K1, for grids and perforated trays of the same size and for questions about option K1, our procurement service accepts enquiries.

Manufacturer's RRP: €253.70
Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert reinforced stainless steel grid B32190 for sizes 450 and 750, option K1 required
Manufacturer number: B32190

Only for units with factory option K1. The grid only fits units that were equipped with option K1 at the factory, a modification of the interior for reinforced grids. This option is only available ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request.The reinforced stainless steel grid B32190 is electropolished and, according to Memmert, can bear up to 60 kg. According to Memmert, the standard grids carry 30 kg per shelf in these sizes. The grid is a shelf level in the interior. It is intended for Memmert units in the U, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The size corresponds to the number in the unit name, for example IF450 or IN450.Please note the maximum load per unit, as it limits the total load of all shelves. The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Heavier loading with reinforced grids or perforated trays up to 60 kg in conjunction with option K1, for example in the IPP750ecoplusTesting and curing of larger components in quality assurance, for example in the UF750Environmental tests from freezing point upwards for larger, heavy test specimens, for example in the HPP750ecoSuitable forModelSizeInterior volume (l)ICP450450449IF450450449IF450plus450449IN450450449IN450plus450449UF450450449UF450TS450449UF450plus450449UN450450449UN450plus450449HPP750eco750749ICH750750749ICP750750749IF750750749IF750plus750749IN750750749IN750plus750749IPP750eco750749IPP750ecoPlus750749UF750750749UF750TS750749UF750plus750749UN750750749UN750plus750749Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmertup to 60 kgScope of delivery1 reinforced stainless steel grid, electropolished, with guide rails and fixing screwsIndividual requirements & procurement serviceFor standard grids, perforated trays and drip trays of the same size, for questions about option K1 and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €508.26
Memmert stainless steel base drip tray B34055 for sizes 450 and 750, option K1 required
Manufacturer number: B34055

Only for units with factory option K1. The drip tray only fits units that were equipped with option K1 at the factory, a modification of the interior with support rails for reinforced grids and perforated trays. This option is available for sizes 450 and 750 and only ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request. The size corresponds to the number in the unit name, for example IF450 or IN450.The B34055 base drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is the version for units with option K1. For units without option K1, the B04362 base drip tray is also available.Memmert points out that it can impair the spatial temperature distribution. It is intended for Memmert units in the U, UF TS, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The table of compatible models shows which series is available in which size.Typical applicationsTasks that occur in the compatible units include, for example:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Shelf-life tests on dairy products, for example in the IPP750ecoForcing tests for beer stability, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)IF450450449IN450450449IF450plus450449IN450plus450449ICP450450449UF450450449UN450450449UF450plus450449UN450plus450449UF450TS450449HPP750eco750749IF750750749IN750750749IF750plus750749IN750plus750749ICH750750749ICP750750749IPP750eco750749IPP750ecoplus750749UF750750749UN750750749UF750plus750749UN750plus750749UF750TS750749Technical detailsMaterialStainless steelRim15 mmRequired optionK1 (ex works only)Scope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray without option K1 and the slide-in drip tray, for questions about option K1 and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €326.80
Stainless steel perforated shelf, illustration
Memmert reinforced stainless steel perforated tray B68521 for sizes 450 and 750, option K1 required
Manufacturer number: B68521

Only for units with factory option K1. The perforated tray only fits units that were equipped with option K1 at the factory, a modification of the interior with support rails for reinforced grids and perforated trays. This option is available for sizes 450 and 750 and only ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request. The size corresponds to the number in the unit name, for example IF450 or IN450.According to Memmert, the reinforced stainless steel perforated tray B68521 can bear up to 60 kg and is supplied with guide rails and fixing screws. According to Memmert, the standard perforated tray B68518 carries 30 kg per shelf in these sizes. The perforated tray is a shelf level in the interior. It is intended for Memmert units in the U, UF TS, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The image is for illustration only.Please note the maximum load per unit. It limits the total load of all shelves. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Heavier loading with reinforced grids or perforated trays up to 60 kg in conjunction with option K1, for example in the IPP750ecoplusHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Environmental tests from freezing point upwards for larger, heavy test specimens, for example in the HPP750ecoSuitable forModelSizeInterior volume (l)IF450450449IN450450449IF450plus450449IN450plus450449ICP450450449UF450450449UN450450449UF450plus450449UN450plus450449UF450TS450449HPP750eco750749IF750750749IN750750749IF750plus750749IN750plus750749ICH750750749ICP750750749IPP750eco750749IPP750ecoplus750749UF750750749UN750750749UF750plus750749UN750plus750749UF750TS750749Technical detailsMaterialStainless steelVersionreinforcedLoad capacity according to Memmertup to 60 kgRequired optionK1 (ex works only)Scope of delivery1 reinforced stainless steel perforated tray with guide rails and fixing screwsIndividual requirements & procurement serviceFor standard perforated trays, grids and drip trays of the same size, for questions about option K1 and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €842.80
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02075 for sizes 450 and 750
Manufacturer number: B02075

The B02075 slide-in drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750; according to Memmert, the maximum load is 8 kg. The size corresponds to the number in the unit name, for example UF450 or UN450.Memmert points out that it can impair the spatial temperature distribution. It cannot be used in conjunction with option K1, the interior modification with support rails for reinforced grids and perforated trays. The table of compatible models shows which series is available in which size. The base drip tray for the same unit size is also available (B04362). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert8 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €253.70