Skip to main content Skip to search Skip to main navigation

Memmert Pass-through oven UF750TS, 749 l, +20 to +250 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert Pass-through oven UF750TS, 749 l, +20 to +250 °C, TwinDISPLAY"

With 749 litres, the Memmert Pass-through oven UF750TS is the largest model of the TS series in our range, and the even larger UF1250TS is available on request. Two fully insulated stainless steel doors provide the airlock function between the grey area and the clean room, and TwinDISPLAY controls the range +20 to +250 °C.

Design: 749 litres and up to 14 shelves

The interior measures 1,040 x 1,200 x 600 mm and the housing externally 1,224 x 1,714 x 782 mm plus the door handles. 2 electropolished stainless steel grid shelves are included as standard, and the cabinet is designed for up to 14 shelves with up to 30 kg each and up to 300 kg total load. The net weight is around 260 kg, and packed in the carton (1,330 x 1,920 x 1,050 mm) around 331 kg.

Control: TwinDISPLAY for the largest TS size

The ControlCOCKPIT controller with TwinDISPLAY and two high-resolution TFT colour graphic displays also handles process control on the largest TS model. HeatBALANCE allows the distribution of the heating power between the upper and lower heating group to be fine-tuned in a range from -50 to +50 %. SetpointWAIT ensures that the set process time runs only once the setpoint temperature in the interior has actually been reached. The electronically controllable air turbine works in 10 % steps, and programmes can be created and transferred via Ethernet or USB with AtmoCONTROL. A setting accuracy of 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C is achieved.

Electrical connection with three-phase current

A three-phase connection with 400 V and 3 x 230 V without neutral conductor is provided for operating the UF750TS, and the connected load is approx. 5,000 W, 50/60 Hz. At the installation site, a maximum altitude of 2,000 m above sea level, an ambient temperature between +5 °C and +40 °C and a relative humidity of at most 80 % without condensation must be observed. The cabinet may only be transported upright.

Safety according to DIN 12880

Process reliability is based on two Pt100 sensors of DIN class A, which monitor each other in 4-wire measurement and automatically take over the function of the other in the event of a fault. In addition, a mechanical temperature limiter of protection class 1 according to DIN 12880 limits the heating around 20 °C above the maximum cabinet temperature, while AutoSAFETY continuously monitors over- and under-temperature and triggers an alarm on deviation. A self-diagnosis system makes fault finding easier, and visual and audible signals indicate faults immediately.

Selection guide: UF450TS, UF750TS or UF1250TS on request

If the capacity of the smaller Memmert pass-through oven UF450TS with 8 shelves is no longer sufficient, the UF750TS with 749 litres and up to 14 shelves offers more space, at the same load of 30 kg per shelf and 300 kg in total. For even larger volumes, Memmert offers the UF1250TS with 1,248 litres. Without an airlock function and with access from one side, the likewise 749 litre Memmert universal oven UF750plus is an option, and its temperature range extends to +300 °C.

Typical applications

With 14 shelves and 749 litres, the UF750TS is designed for the direct transport of load material and samples between the grey area and the clean room.

  • Airlock transfer of large batches or many individual items between the grey area and the clean room
  • Time saved when loading large batches through direct access from both sides
  • Drying and annealing of larger quantities with subsequent transfer into the clean room
  • Reducing the risk of contamination during sample transport through the double door function

Technical details

Setting temperature range+20 to +250 °C
Working temperature rangemin. 10 °C above room temperature to +250 °C
Setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °C
Display resolution, actual value0.1 °C
Temperature sensor2x Pt100, DIN class A, 4-wire measurement, redundant
TimerDigital countdown timer with target time, 1 min to 99 days
Internal volume749 l
Internal dimensions (W x H x D)1,040 x 1,200 x 600 mm
External dimensions (W x H x D)1,224 x 1,714 x 782 mm (plus 2x56 mm door handle)
Net weightapprox. 260 kg
Gross weight (carton)approx. 331 kg
Dimensions incl. carton1,330 x 1,920 x 1,050 mm
Connection400 V and 3 x 230 V without neutral conductor, 50/60 Hz, approx. 5,000 W
Shelves as standard / maximum2 / 14
Max. load, device300 kg
Max. load per shelf30 kg
ControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic display
Additional functionsHeatBALANCE, SetpointWAIT, AutoSAFETY
Permissible ambient temperature+5 °C to +40 °C
Permissible humiditymax. 80 % rel., non-condensing
Maximum installation altitude2,000 m above sea level
Electrical categoryOvervoltage category II, pollution degree 2
MarkingsCE, EAC

Other sizes in the series

The UF750TS is one of five sizes of the TS series, all with TwinDISPLAY, airlock function and a setting range of +20 to +250 °C.

ModelInternal volumeSetting temperatureDisplay
UF160TS161 l+20 to +250 °CTwinDISPLAY
UF260TS256 l+20 to +250 °CTwinDISPLAY
UF450TS449 l+20 to +250 °CTwinDISPLAY
UF750TS (this page)749 l+20 to +250 °CTwinDISPLAY
UF1250TS (on request)1,248 l+20 to +250 °CTwinDISPLAY

Scope of delivery

  • Pass-through oven UF750TS with fully insulated stainless steel doors on both sides
  • Factory calibration certificate (calibration at +160 °C)
  • 2x stainless steel grid shelf, electropolished
  • Installation on feet

Regulatory information

The device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances can be found on our page Environment and disposal.

Installation in a wall opening

For fixed installation in a wall opening, Memmert offers a flush-fit unit set without air slots (B33207). It covers the gap between the pass-through oven and the wall opening with stainless steel. According to Memmert, the installation situation must be clarified technically beforehand. The set is therefore available on request through our procurement service.

Individual requirements and procurement service

For the UF750TS, options available include a full-view glass door with 4-layer insulating glazing up to 250 °C, a door interlock for alternating opening, an additional Pt100 sensor and a fan speed monitor. In addition, reinforced stainless steel grid shelves, slide-in and base drip trays, a built-in frame set for wall installation or a USB-Ethernet adapter can be ordered. For qualification and maintenance, we arrange factory and DAkkS calibration, IQ/OQ documentation according to DIN 12880:2007-05, PQ qualification as well as instruction and maintenance contracts. For the UF1250TS on request or for individual requirements, our procurement service supports you with procurement.

Volume: 749 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E20182 for sizes 450 and 750
Manufacturer number: E20182

The E20182 stainless steel grid is an electropolished shelf for 42 Memmert models in sizes 450 and 750. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example UF450 or UN450.All 42 models have 2 grids as standard. The maximum number is 8 grids (size 450) and 14 grids (size 750). According to Memmert, the load per shelf is 30 kg. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating very large sample quantities or several batches in research and medicine, for example in the IF750Large-volume stability studies of several batches according to ICH Q1A in contract laboratories and pharmaceutical manufacturing, for example in the HPP750ecoHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Suitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)UN450plus2830449UF450plus2830449UF4502830449UN4502830449UF750plus21430749UF75021430749UN75021430749UN750plus21430749IN450plus2830449IN4502830449IF750plus21430749IF450plus2830449IN75021430749IF75021430749IF4502830449IN750plus21430749IF750bw21430749IF450bw2830449IPP750eco21430749IPP750ecoPlus21430749HPP750eco21430749ICH75021430749ICP4502830449ICP75021430749IN450m2830449IN450mplus2830449IF450m2830449IF450mplus2830449IN750m21430749IN750mplus21430749IF750m21430749IF750mplus21430749UN450m2830449UN450mplus2830449UF450m2830449UF450mplus2830449UN750m21430749UN750mplus21430749UF750m21430749UF750mplus21430749UF450TS2830449UF750TS21430749The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert30 kgScope of delivery1 stainless steel grid, electropolished (E20182)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €207.26
memmert boden abtropfschale
Memmert stainless steel base drip tray B04362 for sizes 450 and 750
Manufacturer number: B04362

The stainless steel base drip tray B04362 is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. It has a 15 mm rim, collects dripping liquid and, according to Memmert, can bear a maximum of 8 kg. The size corresponds to the number in the unit name, for example UF450 or UN450.According to Memmert, it can impair the spatial temperature distribution. According to Memmert, it cannot be used in conjunction with option K1, the interior modification with support rails for reinforced grids and perforated trays. The table of compatible models shows which series is available in which size. The slide-in drip tray for the same unit size is also available (B02075). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert8 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €326.80
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68518 for sizes 450 and 750
Manufacturer number: B68518

B68518 is a stainless steel perforated tray for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH, HPPeco and IFbw series in sizes 450 and 750. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example UF450 or UN450. The image is for illustration only.Memmert specifies 30 kg as the maximum load per shelf. The total load of the unit is also limited; the values are given in the unit’s data sheet. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Large-volume drying and heat treatment batches in industry and research, for example in the UF450Incubating very large sample quantities or several batches in research and medicine, for example in the IF750Large-volume stability studies of several batches according to ICH Q1A in contract laboratories and pharmaceutical manufacturing, for example in the HPP750ecoHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Suitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IF750bw750749IF450bw450449IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelLoad per shelf according to Memmert30 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €344.00
Memmert stainless steel slide-in drip tray B32763 for sizes 450 and 750, option K1 required
Manufacturer number: B32763

Only for units with factory option K1. The drip tray only fits units that were equipped with option K1 at the factory, a modification of the interior with support rails for reinforced grids and perforated trays. This option is available for sizes 450 and 750 and only ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request. The size corresponds to the number in the unit name, for example IF450 or IN450.The B32763 slide-in drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is supplied with guide rails and fixing screws and is the version for units with option K1. For units without option K1, the B02075 slide-in drip tray is also available.According to Memmert, it can impair the spatial temperature distribution. It is intended for Memmert units in the U, UF TS, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)IF450450449IN450450449IF450plus450449IN450plus450449ICP450450449UF450450449UN450450449UF450plus450449UN450plus450449UF450TS450449HPP750eco750749IF750750749IN750750749IF750plus750749IN750plus750749ICH750750749ICP750750749IPP750eco750749IPP750ecoplus750749UF750750749UN750750749UF750plus750749UN750plus750749UF750TS750749Technical detailsMaterialStainless steelRim15 mmRequired optionK1 (ex works only)Scope of delivery1 stainless steel slide-in drip tray, 15 mm rim, with guide rails and fixing screwsIndividual requirements & procurement serviceFor the drip tray without option K1, for grids and perforated trays of the same size and for questions about option K1, our procurement service accepts enquiries.

Manufacturer's RRP: €253.70
Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert reinforced stainless steel grid B32190 for sizes 450 and 750, option K1 required
Manufacturer number: B32190

Only for units with factory option K1. The grid only fits units that were equipped with option K1 at the factory, a modification of the interior for reinforced grids. This option is only available ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request.The reinforced stainless steel grid B32190 is electropolished and, according to Memmert, can bear up to 60 kg. According to Memmert, the standard grids carry 30 kg per shelf in these sizes. The grid is a shelf level in the interior. It is intended for Memmert units in the U, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The size corresponds to the number in the unit name, for example IF450 or IN450.Please note the maximum load per unit, as it limits the total load of all shelves. The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Heavier loading with reinforced grids or perforated trays up to 60 kg in conjunction with option K1, for example in the IPP750ecoplusTesting and curing of larger components in quality assurance, for example in the UF750Environmental tests from freezing point upwards for larger, heavy test specimens, for example in the HPP750ecoSuitable forModelSizeInterior volume (l)ICP450450449IF450450449IF450plus450449IN450450449IN450plus450449UF450450449UF450TS450449UF450plus450449UN450450449UN450plus450449HPP750eco750749ICH750750749ICP750750749IF750750749IF750plus750749IN750750749IN750plus750749IPP750eco750749IPP750ecoPlus750749UF750750749UF750TS750749UF750plus750749UN750750749UN750plus750749Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmertup to 60 kgScope of delivery1 reinforced stainless steel grid, electropolished, with guide rails and fixing screwsIndividual requirements & procurement serviceFor standard grids, perforated trays and drip trays of the same size, for questions about option K1 and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €508.26
Memmert stainless steel base drip tray B34055 for sizes 450 and 750, option K1 required
Manufacturer number: B34055

Only for units with factory option K1. The drip tray only fits units that were equipped with option K1 at the factory, a modification of the interior with support rails for reinforced grids and perforated trays. This option is available for sizes 450 and 750 and only ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request. The size corresponds to the number in the unit name, for example IF450 or IN450.The B34055 base drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is the version for units with option K1. For units without option K1, the B04362 base drip tray is also available.Memmert points out that it can impair the spatial temperature distribution. It is intended for Memmert units in the U, UF TS, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The table of compatible models shows which series is available in which size.Typical applicationsTasks that occur in the compatible units include, for example:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Shelf-life tests on dairy products, for example in the IPP750ecoForcing tests for beer stability, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)IF450450449IN450450449IF450plus450449IN450plus450449ICP450450449UF450450449UN450450449UF450plus450449UN450plus450449UF450TS450449HPP750eco750749IF750750749IN750750749IF750plus750749IN750plus750749ICH750750749ICP750750749IPP750eco750749IPP750ecoplus750749UF750750749UN750750749UF750plus750749UN750plus750749UF750TS750749Technical detailsMaterialStainless steelRim15 mmRequired optionK1 (ex works only)Scope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray without option K1 and the slide-in drip tray, for questions about option K1 and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €326.80
Stainless steel perforated shelf, illustration
Memmert reinforced stainless steel perforated tray B68521 for sizes 450 and 750, option K1 required
Manufacturer number: B68521

Only for units with factory option K1. The perforated tray only fits units that were equipped with option K1 at the factory, a modification of the interior with support rails for reinforced grids and perforated trays. This option is available for sizes 450 and 750 and only ex works. If in doubt, ask us before ordering and state the serial number of your unit. For a new unit, option K1 can be ordered on request. The size corresponds to the number in the unit name, for example IF450 or IN450.According to Memmert, the reinforced stainless steel perforated tray B68521 can bear up to 60 kg and is supplied with guide rails and fixing screws. According to Memmert, the standard perforated tray B68518 carries 30 kg per shelf in these sizes. The perforated tray is a shelf level in the interior. It is intended for Memmert units in the U, UF TS, I, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750. The image is for illustration only.Please note the maximum load per unit. It limits the total load of all shelves. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Heavier loading with reinforced grids or perforated trays up to 60 kg in conjunction with option K1, for example in the IPP750ecoplusHeat treatment of very large material batches in industrial multi-shift operation, for example in the UN750Environmental tests from freezing point upwards for larger, heavy test specimens, for example in the HPP750ecoSuitable forModelSizeInterior volume (l)IF450450449IN450450449IF450plus450449IN450plus450449ICP450450449UF450450449UN450450449UF450plus450449UN450plus450449UF450TS450449HPP750eco750749IF750750749IN750750749IF750plus750749IN750plus750749ICH750750749ICP750750749IPP750eco750749IPP750ecoplus750749UF750750749UN750750749UF750plus750749UN750plus750749UF750TS750749Technical detailsMaterialStainless steelVersionreinforcedLoad capacity according to Memmertup to 60 kgRequired optionK1 (ex works only)Scope of delivery1 reinforced stainless steel perforated tray with guide rails and fixing screwsIndividual requirements & procurement serviceFor standard perforated trays, grids and drip trays of the same size, for questions about option K1 and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €842.80
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02075 for sizes 450 and 750
Manufacturer number: B02075

The B02075 slide-in drip tray is made of stainless steel, has a 15 mm rim and collects dripping liquid. It is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 450 and 750; according to Memmert, the maximum load is 8 kg. The size corresponds to the number in the unit name, for example UF450 or UN450.Memmert points out that it can impair the spatial temperature distribution. It cannot be used in conjunction with option K1, the interior modification with support rails for reinforced grids and perforated trays. The table of compatible models shows which series is available in which size. The base drip tray for the same unit size is also available (B04362). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying large quantities of laboratory glassware and sample vessels in multi-shift operation, for example in the UF750Forcing tests for beer stability, for example in the IPP750ecoShelf-life tests on dairy products, for example in the IPP750ecoSuitable forModelSizeInterior volume (l)UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749IN450plus450449IN450450449IF750plus750749IF450plus450449IN750750749IF750750749IF450450449IN750plus750749IPP750eco750749IPP750ecoPlus750749HPP750eco750749ICH750750749ICP450450449ICP750750749IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF450TS450449UF750TS750749Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert8 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €253.70