Suitable for 3 Memmert models in sizes 29, 49 and 101
ⓘ This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.
Product information "Memmert signal cable B39410, 3 m, for pump control, for vacuum drying oven VO 29, 49 and 101"
The signal cable B39410 is 3 m long. It is used for speed control and for optimising the pump performance by activating flushing cycles of the Memmert pump as required. It is not required if a pump module is ordered or already available.
According to Memmert, when drying goods with a high moisture content, the pump performance can decline due to condensation in the pump heads. Brief flushing with fresh air clears the diaphragms. According to Memmert, the demand-controlled speed regulation saves energy and protects the pump diaphragms. The table shows the compatible VO vacuum drying ovens.
Typical applications
Typical uses in the compatible units:
Drying granules and powder in vacuum cycles, for example in the VO29
Drying larger quantities of powder or granules in vacuum cycles, for example in the VO101
Vacuum drying of food and cosmetics, for example in the VO29
For the vacuum connecting hose, for questions about the pump module and about controlling another vacuum pump, our procurement service accepts enquiries.
The Memmert Vacuum drying oven VO29 is the smallest size in the VO series. The interior holds 29 litres and measures 385 x 305 x 250 mm (W x H x D), the unit measures 550 x 607 x 400 mm externally, and the door handle adds 38 mm to the depth. At approx. 55 kg net weight, it is the lightest VO. The temperature is set between +20 and +200 °C, the pressure digitally between 5 and 1,100 mbar, and operation is via the TwinDISPLAY of the ControlCOCKPIT.Loading: one thermal shelf instead of a shelfThe scope of delivery includes a thermal shelf made of aluminium (material 3.3547) with integrated large-area heating. It replaces the shelf that is otherwise usual. Up to 2 shelves are possible in total, each may be loaded with 20 kg, and the unit as a whole with 40 kg. There is a connection for the thermal shelf in the rear wall. The Premium module T5 can be selected as a factory option when ordering and includes, among other things, further thermal shelf connections (one for size 29).The interior is welded tight and made of stainless steel 1.4404. A removable interior lining of the same material carries the support rails with tilt protection on the sides, and the ceiling lining serves against ventilation turbulence.Direct heating and temperature controlHeating takes place in the thermal shelf itself. A fuzzy-assisted MLC microprocessor control (Multi-Level-Controlling) adapts the heating power to shelf and load quantity, and measurement is by a Pt100 in 4-wire technology directly at the shelf. The working temperature range begins at least 5 °C above room temperature and ends at +200 °C. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. Every supplied thermal shelf comes with a factory calibration certificate for +160 °C at 20 mbar.Vacuum and pump connectionOn the outlet side, the VO29 has a small flange DN16, plus a gas inlet with fresh air supply and a programmable, digitally controlled air inlet. The pipework in the suction and ventilation area is made of material 1.4571 (ASTM 316 Ti). The permissible ultimate vacuum of the oven is 0.01 mbar, and the maximum leak rate is 0.01 bar/h.The vacuum pump is not part of the scope of delivery and is ordered separately. Memmert offers the chemically resistant 4-head diaphragm pump E07509 (approx. 50 Nl/min = 3.0 m³/h, 230 V). It runs with speed control, and the oven also outputs a pump ON/OFF signal and triggers demand-based flushing cycles of the pump diaphragms. Signal cable B39410 and connecting hose B04026 (3 m each) are required for this. As a noise-damping base cabinet there is the pump module PM29 (without pump, to hold the vacuum pump) or PMP29 (with built-in pump). Together with the base frame B63505, oven and pump module form a stacked unit with a total height of 1,650 mm. With the module with pump, signal cable and hose are not needed.Programs, timer and interfacesThe TwinDISPLAY consists of two high-resolution TFT colour graphic displays. Settable are temperature (Celsius or Fahrenheit), pressure, program runtime, time zone and summer/winter time, and the menu language is selected from nine languages. The digital countdown clock runs from 1 minute to 99 days with target time indication. With SetpointWAIT, the process time begins only when the setpoint temperature has been reached. Programs are created, managed and transferred via Ethernet LAN or USB with the AtmoCONTROL software. The program sequence is saved in the event of a power failure.Protection and installationA mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heating off at approximately 10 °C above the maximum oven temperature. In addition, the AutoSAFETY protection ASF follows the setpoint at a freely selectable interval, reports exceeding and falling below visually and acoustically, and switches the heating off when exceeded. A self-diagnosis system supports troubleshooting of the temperature control. The door is built as a full-view glass door: spring-mounted safety glass of 15 mm thickness on the inside, and a splinter-protection pane on the outside.Installation is at +5 to +40 °C ambient temperature and a maximum of 80 % relative humidity, non-condensing. A distance of 15 cm to the rear wall is to be observed, 20 cm to the ceiling and 8 cm at the sides. The unit is transported upright.Selection guide: when the VO29 is enoughThe VO29 fits if material to be dried and shelves fit within 385 x 305 x 250 mm and 20 kg per shelf is sufficient. The VO49 has the same internal width and the same external width of 550 mm, but offers 385 mm height and 330 mm depth, two thermal shelf connections from the factory and 60 kg unit load. Anyone who needs more height or depth switches to it. For even larger batches there is the series up to 101 litres, see size table below.Typical applicationsThe VO29 dries under vacuum. Typical materials to be dried are food, cosmetics, granules, watches, books, printed circuit boards, electronic components and injection moulds.Vacuum drying of food and cosmeticsDrying of granules and powder in vacuum cyclesDrying of printed circuit boards and electronic componentsVacuum drying of watches, books and injection mouldsTechnical detailsSetting temperature range+20 to +200 °CWorking temperature rangemin. 5 °C above room temperature to +200 °CTemperature setting accuracy0.1 °C up to 99.9 °C setpoint temperature, 0.5 °C from 100 °CTemperature sensorPt100, 4-wire measurement, separate for each thermal shelfVacuum range5 to 1,100 mbar, digital pressure controlPermissible ultimate vacuum0.01 mbarMaximum leak rate0.01 bar/hVacuum connectionSmall flange DN16, gas inlet with fresh air supplyInternal volume29 lInternal dimensions (W x H x D)385 x 305 x 250 mmExternal dimensions (W x H x D)550 x 607 x 400 mm (depth plus 38 mm door handle)Net weightapprox. 55 kgGross weight incl. cartonapprox. 76 kgCarton dimensions (W x H x D)660 x 870 x 590 mmThermal shelves in scope of delivery1Max. number of shelves2Max. load per shelf20 kgMax. load per unit40 kgThermal shelf connection1 connection in the rear wallControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayTimerdigital countdown clock, 1 minute to 99 daysInterfacesEthernet LAN, USBConnection voltage230 V, 50/60 HzPermissible ambient temperature+5 to +40 °CPermissible humiditymax. 80 % rel., non-condensingOvervoltage category / pollution degreeII / 2MarkingsCE, VDE, cMETusOther sizes in the seriesThe VO series comprises three sizes from 29 to 101 litres, all with TwinDISPLAY, sorted by internal volume:ModelInternal volumeSetting temperaturePressure rangeVO29 (this page)29 l+20 to +200 °C5 to 1,100 mbarVO4949 l+20 to +200 °C5 to 1,100 mbarVO101101 l+20 to +200 °C5 to 1,100 mbarScope of delivery1x Memmert Vacuum drying oven VO291 thermal shelf made of aluminium (material 3.3547) with integrated large-area heatingFactory calibration certificate for +160 °C at 20 mbar pressure for every supplied thermal shelfFull-view glass door, spring-mounted 15 mm thick safety glass on the inside, splinter-protection pane on the outsideRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.Individual requirements and procurement serviceAvailable as factory options for the VO29 are the Premium module T5 (including inert gas switching), the current interface V6 (4 to 20 mA, temperature of a Pt100 that can be freely positioned in the interior, price per sensor, only with T5), the potential-free contact H6 to NAMUR NE 28 for fault messages and MobileALERT C3 for alarm notification by SMS (requires H6). Accessories include additional thermal shelves made of anodised aluminium (B00741) or stainless steel 1.4404 (B00733), the vacuum pump E07509 with signal cable and hose, the pump module PM29 or PMP29 with base frame B63505, USB-Ethernet adapter, Ethernet cable (5 m), USB user ID stick and the FDA licence FDAQ1 for AtmoCONTROL FDA. Services range from factory calibration (+50, +100 and +160 °C at 20 mbar) and IQ/OQ documents to short training, maintenance and an on-site maintenance contract. For individual requirements, we will advise you personally.
With 49 litres of internal volume, the VO49 is the middle one of the three VO sizes. Compared with the VO29, the interior grows in height and depth to 385 x 385 x 330 mm, while the width stays the same. The housing measures 550 x 687 x 480 mm (door handle additional 38 mm) and weighs approx. 83 kg. The temperature can be set from +20 to +200 °C, and the pressure is controlled digitally in the range 5 to 1,100 mbar.Two thermal shelf levels in the interiorThe rear wall of the VO49 has two connections for thermal shelves, on the 1st and the 3rd level. One thermal shelf made of aluminium (material 3.3547, integrated large-area heating) is supplied. Each shelf is controlled individually: an MLC microprocessor control with fuzzy-assisted power adjustment according to load quantity, plus its own Pt100 in 4-wire measurement. A maximum of 2 shelves with 20 kg each and 60 kg for the whole unit are permitted.The Premium module T5 can be selected as a factory option when ordering. For size 49 it contains inert gas switching, two further thermal shelf connections and an additional thermal shelf. Memmert supplies further shelves as accessories in anodised aluminium (B00743) or in stainless steel 1.4404 (B00734) for particularly corrosive materials.Pressure control, air inlet and pumpThe pressure can be controlled to a value between 5 and 1,100 mbar. The permissible ultimate vacuum of the oven is 0.01 mbar, and the maximum leak rate is 0.01 bar/h. Suction is via a small flange DN16, and ventilation via the gas inlet with fresh air supply, which opens in a programmable and digitally controlled way. Suction and ventilation lines are made of material 1.4571 (ASTM 316 Ti).A pump is not included in the carton with the VO49. It is ordered as an accessory, for example the chemically resistant 4-head diaphragm pump E07509 with approx. 50 Nl/min (3.0 m³/h) at 230 V. The oven controls its speed, switches it ON and OFF via a signal output and triggers demand-based flushing cycles of the diaphragm. Signal cable B39410 and hose B04026 (3 m each) are additionally mandatory. The pump module PM49 (without pump) or PMP49 (with built-in pump) stands as a noise-damping base cabinet under the oven, and with the PMP49, signal cable and hose are not needed. Together with the base frame B63506, this gives a stacked unit of 1,650 mm height.Control, timing and data pathsThe ControlCOCKPIT works with an adaptive PID controller and two high-resolution TFT colour displays. Parameters such as temperature (Celsius or Fahrenheit), pressure and program runtime are settable, as are time zone and summer/winter time. The timer counts down from 1 minute to 99 days and states the target time, and SetpointWAIT shifts the start of timing to the moment when the setpoint temperature is reached. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C, and 0.5 °C above that.Programs can be written, managed and loaded onto the unit via Ethernet LAN or USB with the AtmoCONTROL software. The program sequence is saved in the event of a power failure. Two current interfaces are available as factory options: V3 outputs the actual temperature value from 0 to 210 °C as 4 to 20 mA, V6 the value of a Pt100 that can be freely positioned in the interior (both only with T5).Protective devices and locationThe mechanical temperature limiter (protection class 1, DIN 12880) disconnects the heating at approximately 10 °C above the maximum oven temperature. The AutoSAFETY protection ASF follows the setpoint at a freely selectable interval and triggers an optical and acoustic alarm when exceeded or fallen below, and additionally the heating shutdown when exceeded. The door consists of a full-view glass pane with spring-mounted 15 mm safety glass on the inside and a splinter-protection pane on the outside.Installation is at +5 to +40 °C and a maximum of 80 % humidity, non-condensing. At the sides 8 cm of space to the wall remain, 15 cm to the rear wall, 20 cm to the ceiling. The oven is transported upright.Choosing a size: VO29, VO49 or VO101The VO29 offers 29 litres and one connection in the rear wall, at 40 kg unit load. It is sufficient if the load fits in 385 x 305 x 250 mm. The VO49 has 20 litres more internal volume and two connections. The VO101 reaches 545 x 465 x 400 mm interior at 710 mm external width and approx. 110 kg net weight, and the load capacity per shelf stays at 20 kg.Typical applicationsVacuum drying is the job of this oven. Typical materials to be dried in the series are food, cosmetics, granules, watches, books, printed circuit boards, electronic components and injection moulds.Drying food and cosmetics under vacuumDrying powder and granules with vacuum cyclesDrying printed circuit boards and electronic componentsVacuum drying of watches, books and injection mouldsTechnical detailsInternal volume49 lInternal dimensions (W x H x D)385 x 385 x 330 mmExternal dimensions (W x H x D)550 x 687 x 480 mm (depth plus 38 mm door handle)Setting temperature range+20 to +200 °CWorking temperature rangemin. 5 °C above room temperature to +200 °CTemperature setting accuracy0.1 °C up to 99.9 °C setpoint temperature, 0.5 °C from 100 °CTemperature sensorPt100, 4-wire measurement, separate for each thermal shelfVacuum range5 to 1,100 mbar, digital pressure controlPermissible ultimate vacuum0.01 mbarMaximum leak rate0.01 bar/hVacuum connectionSmall flange DN16, gas inlet with fresh air supplyThermal shelf connections2 in the rear wall (1st and 3rd level)Thermal shelves in scope of delivery1Shelves maximum2Max. load per shelf20 kgMax. load unit60 kgWeight netapprox. 83 kgWeight gross incl. cartonapprox. 104 kgCarton dimensions (W x H x D)670 x 890 x 630 mmControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayTimerdigital countdown clock, 1 minute to 99 daysInterfacesEthernet LAN, USBConnection voltage230 V, 50/60 HzPermissible ambient temperature+5 to +40 °CPermissible humiditymax. 80 % rel., non-condensingOvervoltage category / pollution degreeII / 2MarkingsCE, VDE, cMETusOther sizes in the seriesThe three VO sizes differ in internal volume, while temperature and pressure range are the same:ModelInternal volumeSetting temperaturePressure rangeVO2929 l+20 to +200 °C5 to 1,100 mbarVO49 (this page)49 l+20 to +200 °C5 to 1,100 mbarVO101101 l+20 to +200 °C5 to 1,100 mbarScope of delivery1x Memmert Vacuum drying oven VO491 thermal shelf made of aluminium (material 3.3547) with integrated large-area heatingFactory calibration certificate for +160 °C at 20 mbar pressure for every supplied thermal shelfFull-view glass door with spring-mounted 15 mm thick safety glass on the inside and splinter-protection pane on the outsideRegulatory informationThe unit is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.Individual requirements and procurement serviceAvailable as factory options for the VO49 are the Premium module T5, the current interfaces V3 and V6, the potential-free contact H6 (24 V/2 A, NAMUR NE 28) as well as MobileALERT C3 and C4. C3 reports every fault by SMS and requires H6, while C4 reports two alarm messages (temperature and vacuum) and requires T5 and H6. Accessories include pump E07509, signal cable, hose, pump module PM49 or PMP49, base frame B63506, additional thermal shelves, USB-Ethernet adapter, Ethernet cable, user ID stick and the FDA licence FDAQ1. Services include factory calibration, IQ/OQ documents, on-site qualification and calibration, short training as well as maintenance and a maintenance contract (minimum term 3 years). For your specific requirements, we put together equipment and quotation individually.
With 101 litres of internal volume, the VO101 is the largest version of the Memmert VO series. The interior measures 545 x 465 x 400 mm and the housing 710 x 767 x 550 mm, plus 38 mm for the door handle. The oven weighs approx. 110 kg net. The temperature can be set from +20 to +200 °C, and the pressure digitally from 5 to 1,100 mbar.The large interior and its load limitsThe interior is welded tight and made of stainless steel 1.4404. A removable lining of the same steel with support rails, tilt protection and ceiling lining against ventilation turbulence sits inside. The unit may be loaded with 60 kg in total, and each of the maximum 2 shelves with 20 kg.An aluminium thermal shelf (material 3.3547) with integrated large-area heating is part of the scope of delivery. Two connections in the rear wall (1st and 3rd level) accept thermal shelves. Each shelf has its own MLC control and a Pt100 sensor in 4-wire measurement. The Premium module T5 includes an additional thermal shelf from the factory as well as further connections. As accessories, further shelves made of anodised aluminium (B00744) or stainless steel 1.4404 (B00735) are available.Vacuum cycles for larger quantitiesThe applications of the series include drying larger quantities of powder or granules with vacuum cycles. Temperature, pressure and program runtime are settable, and the digital pressure control works in the range 5 to 1,100 mbar. The permissible ultimate vacuum is 0.01 mbar, and the leak rate is 0.01 bar/h at most. A programmable, digitally controlled air inlet ventilates the chamber, and the pipework in the suction and ventilation area is made of material 1.4571 (ASTM 316 Ti).Pump, pump module and base frameVacuum pump and accessories for connection are not in the scope of delivery. The oven has a small flange DN16 for extraction and a gas inlet with fresh air supply. The chemically resistant 4-head diaphragm pump E07509 with approx. 50 Nl/min (3.0 m³/h) and 230 V is available for selection. It is switched ON and OFF via a signal output, and the oven controls its speed and the flushing cycles of the diaphragm on demand. Signal cable B39410 and hose B04026 with 3 m each are also mandatory. When a pump module with built-in pump (PMP101) is ordered, both are not needed, and the module without pump is called PM101. Oven and pump module form a stacked unit of 1,650 mm height with the base frame B63507.Operation, documentation and alarmTwo TFT colour graphic displays form the TwinDISPLAY, and the language can be selected from nine. The countdown clock covers 1 minute to 99 days, and SetpointWAIT starts the runtime only when the setpoint temperature has been reached. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. Programs are created and managed with AtmoCONTROL and transferred via Ethernet LAN or USB, and the program sequence is saved in the event of a power failure. For FDA requirements under 21 CFR Part 11, the licence FDAQ1 for AtmoCONTROL FDA is available as an accessory. As a factory option there is the current interface V3, which outputs the actual temperature value from 0 to 210 °C as 4 to 20 mA (only with T5).Safety technologyThe heating is switched off by the mechanical temperature limiter of protection class 1 according to DIN 12880 at approximately 10 °C above the maximum oven temperature. ASF, the AutoSAFETY monitoring, keeps a freely selectable interval to the setpoint, alarms visually and acoustically when fallen below or exceeded, and switches the heating off when exceeded. The self-diagnosis system checks the temperature control. The full-view glass door consists of spring-mounted 15 mm safety glass on the inside and a splinter-protection pane on the outside.For installation, 15 cm distance to the rear wall, 20 cm to the ceiling and 8 cm at the sides apply, with an environment of +5 to +40 °C at a maximum of 80 % relative humidity without condensation. The oven is transported upright.Selection guide: when a smaller VO is enoughThe VO49 has the same temperature and pressure range, an interior of 385 x 385 x 330 mm and approx. 83 kg net weight. With 60 kg unit load and 20 kg per shelf, both units are equal in load capacity. The interior therefore decides above all: if the material to be dried fits in 385 x 385 x 330 mm, the smaller oven is enough. Only when width, height or depth go beyond that does the VO101 with 545 x 465 x 400 mm become interesting.Typical applicationsThe VO101 is used for vacuum drying. Typical materials to be dried are food, cosmetics, granules, watches, books, printed circuit boards, electronic components and injection moulds, as well as larger quantities of powder or granules.Drying larger quantities of powder or granules with vacuum cyclesVacuum drying of food and cosmeticsDrying printed circuit boards and electronic componentsDrying watches, books and injection mouldsTechnical detailsInternal volume101 lInternal dimensions (W x H x D)545 x 465 x 400 mmExternal dimensions (W x H x D)710 x 767 x 550 mm (depth plus 38 mm door handle)Weight netapprox. 110 kgWeight gross incl. cartonapprox. 135 kgCarton dimensions (W x H x D)820 x 970 x 670 mmSetting temperature range+20 to +200 °CWorking temperature rangemin. 5 °C above room temperature to +200 °CTemperature setting accuracy0.1 °C up to 99.9 °C setpoint temperature, 0.5 °C from 100 °CTemperature sensorPt100, 4-wire measurement, separate for each thermal shelfVacuum range5 to 1,100 mbar, digital pressure controlPermissible ultimate vacuum0.01 mbarMaximum leak rate0.01 bar/hVacuum connectionSmall flange DN16, gas inlet with fresh air supplyThermal shelf connections2 in the rear wall (1st and 3rd level)Thermal shelves in scope of delivery1Shelves maximum2Max. load per shelf20 kgMax. load unit60 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayTimerdigital countdown clock, 1 minute to 99 daysInterfacesEthernet LAN, USBConnection voltage230 V, 50/60 HzPermissible ambient temperature+5 to +40 °CPermissible humiditymax. 80 % rel., non-condensingOvervoltage category / pollution degreeII / 2MarkingsCE, VDE, cMETusOther sizes in the seriesThe VO series consists of three sizes, and the VO101 is the largest:ModelInternal volumeSetting temperaturePressure rangeVO2929 l+20 to +200 °C5 to 1,100 mbarVO4949 l+20 to +200 °C5 to 1,100 mbarVO101 (this page)101 l+20 to +200 °C5 to 1,100 mbarScope of delivery1x Memmert Vacuum drying oven VO1011 thermal shelf made of aluminium (material 3.3547) with integrated large-area heatingFactory calibration certificate for +160 °C at 20 mbar pressure for every supplied thermal shelfFull-view glass door with spring-mounted 15 mm thick safety glass on the inside and splinter-protection pane on the outsideRegulatory informationThe unit is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.Individual requirements and procurement serviceAvailable as factory options are the Premium module T5, the current interfaces V3 and V6, the potential-free contact H6 and MobileALERT (C3 by SMS for every message, C4 for temperature and vacuum alarm). On the accessories side there are pump E07509 with signal cable and hose, the pump modules PM101 and PMP101, the base frame B63507, further thermal shelves, interface accessories, user ID stick and FDAQ1. In addition, factory calibration, IQ/OQ documents, on-site qualification, short training, maintenance and a maintenance contract (minimum term 3 years) can be ordered. How oven, pump and options fit together for your process is something we clarify with you case by case.