Skip to main content Skip to search Skip to main navigation

Memmert Vacuum drying oven VO49, 49 l, +20 to +200 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert Vacuum drying oven VO49, 49 l, +20 to +200 °C, TwinDISPLAY"

With 49 litres of internal volume, the VO49 is the middle one of the three VO sizes. Compared with the VO29, the interior grows in height and depth to 385 x 385 x 330 mm, while the width stays the same. The housing measures 550 x 687 x 480 mm (door handle additional 38 mm) and weighs approx. 83 kg. The temperature can be set from +20 to +200 °C, and the pressure is controlled digitally in the range 5 to 1,100 mbar.

Two thermal shelf levels in the interior

The rear wall of the VO49 has two connections for thermal shelves, on the 1st and the 3rd level. One thermal shelf made of aluminium (material 3.3547, integrated large-area heating) is supplied. Each shelf is controlled individually: an MLC microprocessor control with fuzzy-assisted power adjustment according to load quantity, plus its own Pt100 in 4-wire measurement. A maximum of 2 shelves with 20 kg each and 60 kg for the whole unit are permitted.

The Premium module T5 can be selected as a factory option when ordering. For size 49 it contains inert gas switching, two further thermal shelf connections and an additional thermal shelf. Memmert supplies further shelves as accessories in anodised aluminium (B00743) or in stainless steel 1.4404 (B00734) for particularly corrosive materials.

Pressure control, air inlet and pump

The pressure can be controlled to a value between 5 and 1,100 mbar. The permissible ultimate vacuum of the oven is 0.01 mbar, and the maximum leak rate is 0.01 bar/h. Suction is via a small flange DN16, and ventilation via the gas inlet with fresh air supply, which opens in a programmable and digitally controlled way. Suction and ventilation lines are made of material 1.4571 (ASTM 316 Ti).

A pump is not included in the carton with the VO49. It is ordered as an accessory, for example the chemically resistant 4-head diaphragm pump E07509 with approx. 50 Nl/min (3.0 m³/h) at 230 V. The oven controls its speed, switches it ON and OFF via a signal output and triggers demand-based flushing cycles of the diaphragm. Signal cable B39410 and hose B04026 (3 m each) are additionally mandatory. The pump module PM49 (without pump) or PMP49 (with built-in pump) stands as a noise-damping base cabinet under the oven, and with the PMP49, signal cable and hose are not needed. Together with the base frame B63506, this gives a stacked unit of 1,650 mm height.

Control, timing and data paths

The ControlCOCKPIT works with an adaptive PID controller and two high-resolution TFT colour displays. Parameters such as temperature (Celsius or Fahrenheit), pressure and program runtime are settable, as are time zone and summer/winter time. The timer counts down from 1 minute to 99 days and states the target time, and SetpointWAIT shifts the start of timing to the moment when the setpoint temperature is reached. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C, and 0.5 °C above that.

Programs can be written, managed and loaded onto the unit via Ethernet LAN or USB with the AtmoCONTROL software. The program sequence is saved in the event of a power failure. Two current interfaces are available as factory options: V3 outputs the actual temperature value from 0 to 210 °C as 4 to 20 mA, V6 the value of a Pt100 that can be freely positioned in the interior (both only with T5).

Protective devices and location

The mechanical temperature limiter (protection class 1, DIN 12880) disconnects the heating at approximately 10 °C above the maximum oven temperature. The AutoSAFETY protection ASF follows the setpoint at a freely selectable interval and triggers an optical and acoustic alarm when exceeded or fallen below, and additionally the heating shutdown when exceeded. The door consists of a full-view glass pane with spring-mounted 15 mm safety glass on the inside and a splinter-protection pane on the outside.

Installation is at +5 to +40 °C and a maximum of 80 % humidity, non-condensing. At the sides 8 cm of space to the wall remain, 15 cm to the rear wall, 20 cm to the ceiling. The oven is transported upright.

Choosing a size: VO29, VO49 or VO101

The VO29 offers 29 litres and one connection in the rear wall, at 40 kg unit load. It is sufficient if the load fits in 385 x 305 x 250 mm. The VO49 has 20 litres more internal volume and two connections. The VO101 reaches 545 x 465 x 400 mm interior at 710 mm external width and approx. 110 kg net weight, and the load capacity per shelf stays at 20 kg.

Typical applications

Vacuum drying is the job of this oven. Typical materials to be dried in the series are food, cosmetics, granules, watches, books, printed circuit boards, electronic components and injection moulds.

  • Drying food and cosmetics under vacuum
  • Drying powder and granules with vacuum cycles
  • Drying printed circuit boards and electronic components
  • Vacuum drying of watches, books and injection moulds

Technical details

Internal volume49 l
Internal dimensions (W x H x D)385 x 385 x 330 mm
External dimensions (W x H x D)550 x 687 x 480 mm (depth plus 38 mm door handle)
Setting temperature range+20 to +200 °C
Working temperature rangemin. 5 °C above room temperature to +200 °C
Temperature setting accuracy0.1 °C up to 99.9 °C setpoint temperature, 0.5 °C from 100 °C
Temperature sensorPt100, 4-wire measurement, separate for each thermal shelf
Vacuum range5 to 1,100 mbar, digital pressure control
Permissible ultimate vacuum0.01 mbar
Maximum leak rate0.01 bar/h
Vacuum connectionSmall flange DN16, gas inlet with fresh air supply
Thermal shelf connections2 in the rear wall (1st and 3rd level)
Thermal shelves in scope of delivery1
Shelves maximum2
Max. load per shelf20 kg
Max. load unit60 kg
Weight netapprox. 83 kg
Weight gross incl. cartonapprox. 104 kg
Carton dimensions (W x H x D)670 x 890 x 630 mm
ControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic display
Timerdigital countdown clock, 1 minute to 99 days
InterfacesEthernet LAN, USB
Connection voltage230 V, 50/60 Hz
Permissible ambient temperature+5 to +40 °C
Permissible humiditymax. 80 % rel., non-condensing
Overvoltage category / pollution degreeII / 2
MarkingsCE, VDE, cMETus

Other sizes in the series

The three VO sizes differ in internal volume, while temperature and pressure range are the same:

ModelInternal volumeSetting temperaturePressure range
VO2929 l+20 to +200 °C5 to 1,100 mbar
VO49 (this page)49 l+20 to +200 °C5 to 1,100 mbar
VO101101 l+20 to +200 °C5 to 1,100 mbar

Scope of delivery

  • 1x Memmert Vacuum drying oven VO49
  • 1 thermal shelf made of aluminium (material 3.3547) with integrated large-area heating
  • Factory calibration certificate for +160 °C at 20 mbar pressure for every supplied thermal shelf
  • Full-view glass door with spring-mounted 15 mm thick safety glass on the inside and splinter-protection pane on the outside

Regulatory information

The unit is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.

Individual requirements and procurement service

Available as factory options for the VO49 are the Premium module T5, the current interfaces V3 and V6, the potential-free contact H6 (24 V/2 A, NAMUR NE 28) as well as MobileALERT C3 and C4. C3 reports every fault by SMS and requires H6, while C4 reports two alarm messages (temperature and vacuum) and requires T5 and H6. Accessories include pump E07509, signal cable, hose, pump module PM49 or PMP49, base frame B63506, additional thermal shelves, USB-Ethernet adapter, Ethernet cable, user ID stick and the FDA licence FDAQ1. Services include factory calibration, IQ/OQ documents, on-site qualification and calibration, short training as well as maintenance and a maintenance contract (minimum term 3 years). For your specific requirements, we put together equipment and quotation individually.

Volume: 49 l
Skip product gallery

Matching accessories

Memmert tubular steel base frame B63506 for vacuum drying oven VO49
Manufacturer number: B63506

B63506 is a tubular steel base frame, painted black, for the VO49 vacuum drying oven. It is intended for the stacking unit consisting of vacuum drying oven and pump module.Memmert states a total height of 1,650 mm for this stacking unit.Typical applicationsThe stacking unit consisting of the VO49 and a pump module is placed on the base frame. Typical uses of the VO49:Vacuum drying of foodstuffs and cosmeticsDrying of granules and powders in vacuum cyclesDrying of printed circuit boards and electronic componentsSuitable forModelSizeInterior volume (l)VO494949Technical detailsMaterialTubular steelSurfacepainted blackTotal height of the stacking unit according to Memmert1,650 mmScope of delivery1 tubular steel base frame, painted blackIndividual requirements & procurement serviceFor further accessories for the VO49 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €332.82
memmert thermoblech
Memmert stainless steel 1.4404 thermal shelf B00734 for vacuum drying oven VO49
Manufacturer number: B00734

B00734 is a thermal shelf made of stainless steel, material 1.4404 (ASTM 316 L), for the VO49 vacuum drying oven, intended for particularly corrosive materials. It serves as an additional heated shelf in the interior. According to Memmert, the maximum load per thermal shelf is 20 kg.It has integrated large-area heating with on-site sensors (Pt100, 4-wire measurement) as well as a shelf-specific overtemperature protection (Multi-Level-Overtemperature-Control). According to Memmert, a calibration certificate is only possible when ordering a new unit. The anodised aluminium thermal shelf is also available (B00743). The image is for illustration only.Typical applicationsTypical uses of the VO49 vacuum drying oven:Drying of granules and powders in vacuum cyclesDrying of printed circuit boards and electronic componentsVacuum drying of watches, books and injection mouldsSuitable forModelSizeInterior volume (l)VO494949Technical detailsMaterialStainless steel, material 1.4404 (ASTM 316 L)Heatingintegrated large-area heatingSensorsPt100, 4-wire measurementOvertemperature protectionshelf-specific, Multi-Level-Overtemperature-ControlMaximum load according to Memmert20 kg per thermal shelfScope of delivery1 thermal shelf made of stainless steel, material 1.4404, with integrated large-area heatingIndividual requirements & procurement serviceFor the aluminium thermal shelf, for further accessories for the VO49 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €596.84
memmert thermoblech
Memmert aluminium thermal shelf B00743 for vacuum drying oven VO49
Manufacturer number: B00743

B00743 is a thermal shelf made of anodised aluminium (material 3.3547, ASTM B209) for the VO49 vacuum drying oven. It serves as an additional heated shelf in the interior. According to Memmert, the maximum load per thermal shelf is 20 kg.It has integrated large-area heating with on-site sensors (Pt100, 4-wire measurement) as well as a shelf-specific overtemperature protection (Multi-Level-Overtemperature-Control). According to Memmert, a calibration certificate is only possible when ordering a new unit. For particularly corrosive materials, the thermal shelf made of stainless steel 1.4404 is also available (B00734). The image is for illustration only.Typical applicationsTypical uses of the VO49 vacuum drying oven:Vacuum drying of foodstuffs and cosmeticsDrying of printed circuit boards and electronic componentsVacuum drying of watches, books and injection mouldsSuitable forModelSizeInterior volume (l)VO494949Technical detailsMaterialAluminium, anodised, material 3.3547 (ASTM B209)Heatingintegrated large-area heatingSensorsPt100, 4-wire measurementOvertemperature protectionshelf-specific, Multi-Level-Overtemperature-ControlMaximum load according to Memmert20 kg per thermal shelfScope of delivery1 anodised aluminium thermal shelf with integrated large-area heatingIndividual requirements & procurement serviceFor the stainless steel thermal shelf, for further accessories for the VO49 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €596.84
Memmert vacuum connecting hose B04026, 3 m, for vacuum drying oven VO 29, 49 and 101
Manufacturer number: B04026

The vacuum connecting hose B04026 is 3 m long and connects the vacuum drying oven to the Memmert pump. Optimised connection accessories, some of which are made of stainless steel, are included.It is not required if a pump module with pump is ordered or already available. According to Memmert, the vacuum connection on the rear of the unit is connected via the connecting hose to the vacuum pump connection of the pump module or of another suitable vacuum pump. The table shows the compatible VO vacuum drying ovens.Typical applicationsTypical uses in the compatible units:Drying food and cosmetics under vacuum, for example in the VO49Drying printed circuit boards and electronic components, for example in the VO49Vacuum drying of watches, books and injection moulds, for example in the VO29Suitable forModelSizeInterior volume (l)VO292929VO494949VO101101101Technical detailsLength3 mConnection accessoriesoptimised, partly made of stainless steelScope of delivery1 vacuum connecting hose, 3 m, with connection accessoriesIndividual requirements & procurement serviceFor the signal cable for pump control, for questions about the pump module and about connecting another vacuum pump, our procurement service accepts enquiries.

Manufacturer's RRP: €225.32
Memmert signal cable B39410, 3 m, for pump control, for vacuum drying oven VO 29, 49 and 101
Manufacturer number: B39410

The signal cable B39410 is 3 m long. It is used for speed control and for optimising the pump performance by activating flushing cycles of the Memmert pump as required. It is not required if a pump module is ordered or already available.According to Memmert, when drying goods with a high moisture content, the pump performance can decline due to condensation in the pump heads. Brief flushing with fresh air clears the diaphragms. According to Memmert, the demand-controlled speed regulation saves energy and protects the pump diaphragms. The table shows the compatible VO vacuum drying ovens.Typical applicationsTypical uses in the compatible units:Drying granules and powder in vacuum cycles, for example in the VO29Drying larger quantities of powder or granules in vacuum cycles, for example in the VO101Vacuum drying of food and cosmetics, for example in the VO29Suitable forModelSizeInterior volume (l)VO292929VO494949VO101101101Technical detailsLength3 mScope of delivery1 signal cable, 3 mIndividual requirements & procurement serviceFor the vacuum connecting hose, for questions about the pump module and about controlling another vacuum pump, our procurement service accepts enquiries.

Manufacturer's RRP: €167.70