Skip to main content Skip to search Skip to main navigation

Memmert Vacuum drying oven VO29, 29 l, +20 to +200 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert Vacuum drying oven VO29, 29 l, +20 to +200 °C, TwinDISPLAY"

The Memmert Vacuum drying oven VO29 is the smallest size in the VO series. The interior holds 29 litres and measures 385 x 305 x 250 mm (W x H x D), the unit measures 550 x 607 x 400 mm externally, and the door handle adds 38 mm to the depth. At approx. 55 kg net weight, it is the lightest VO. The temperature is set between +20 and +200 °C, the pressure digitally between 5 and 1,100 mbar, and operation is via the TwinDISPLAY of the ControlCOCKPIT.

Loading: one thermal shelf instead of a shelf

The scope of delivery includes a thermal shelf made of aluminium (material 3.3547) with integrated large-area heating. It replaces the shelf that is otherwise usual. Up to 2 shelves are possible in total, each may be loaded with 20 kg, and the unit as a whole with 40 kg. There is a connection for the thermal shelf in the rear wall. The Premium module T5 can be selected as a factory option when ordering and includes, among other things, further thermal shelf connections (one for size 29).

The interior is welded tight and made of stainless steel 1.4404. A removable interior lining of the same material carries the support rails with tilt protection on the sides, and the ceiling lining serves against ventilation turbulence.

Direct heating and temperature control

Heating takes place in the thermal shelf itself. A fuzzy-assisted MLC microprocessor control (Multi-Level-Controlling) adapts the heating power to shelf and load quantity, and measurement is by a Pt100 in 4-wire technology directly at the shelf. The working temperature range begins at least 5 °C above room temperature and ends at +200 °C. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. Every supplied thermal shelf comes with a factory calibration certificate for +160 °C at 20 mbar.

Vacuum and pump connection

On the outlet side, the VO29 has a small flange DN16, plus a gas inlet with fresh air supply and a programmable, digitally controlled air inlet. The pipework in the suction and ventilation area is made of material 1.4571 (ASTM 316 Ti). The permissible ultimate vacuum of the oven is 0.01 mbar, and the maximum leak rate is 0.01 bar/h.

The vacuum pump is not part of the scope of delivery and is ordered separately. Memmert offers the chemically resistant 4-head diaphragm pump E07509 (approx. 50 Nl/min = 3.0 m³/h, 230 V). It runs with speed control, and the oven also outputs a pump ON/OFF signal and triggers demand-based flushing cycles of the pump diaphragms. Signal cable B39410 and connecting hose B04026 (3 m each) are required for this. As a noise-damping base cabinet there is the pump module PM29 (without pump, to hold the vacuum pump) or PMP29 (with built-in pump). Together with the base frame B63505, oven and pump module form a stacked unit with a total height of 1,650 mm. With the module with pump, signal cable and hose are not needed.

Programs, timer and interfaces

The TwinDISPLAY consists of two high-resolution TFT colour graphic displays. Settable are temperature (Celsius or Fahrenheit), pressure, program runtime, time zone and summer/winter time, and the menu language is selected from nine languages. The digital countdown clock runs from 1 minute to 99 days with target time indication. With SetpointWAIT, the process time begins only when the setpoint temperature has been reached. Programs are created, managed and transferred via Ethernet LAN or USB with the AtmoCONTROL software. The program sequence is saved in the event of a power failure.

Protection and installation

A mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heating off at approximately 10 °C above the maximum oven temperature. In addition, the AutoSAFETY protection ASF follows the setpoint at a freely selectable interval, reports exceeding and falling below visually and acoustically, and switches the heating off when exceeded. A self-diagnosis system supports troubleshooting of the temperature control. The door is built as a full-view glass door: spring-mounted safety glass of 15 mm thickness on the inside, and a splinter-protection pane on the outside.

Installation is at +5 to +40 °C ambient temperature and a maximum of 80 % relative humidity, non-condensing. A distance of 15 cm to the rear wall is to be observed, 20 cm to the ceiling and 8 cm at the sides. The unit is transported upright.

Selection guide: when the VO29 is enough

The VO29 fits if material to be dried and shelves fit within 385 x 305 x 250 mm and 20 kg per shelf is sufficient. The VO49 has the same internal width and the same external width of 550 mm, but offers 385 mm height and 330 mm depth, two thermal shelf connections from the factory and 60 kg unit load. Anyone who needs more height or depth switches to it. For even larger batches there is the series up to 101 litres, see size table below.

Typical applications

The VO29 dries under vacuum. Typical materials to be dried are food, cosmetics, granules, watches, books, printed circuit boards, electronic components and injection moulds.

  • Vacuum drying of food and cosmetics
  • Drying of granules and powder in vacuum cycles
  • Drying of printed circuit boards and electronic components
  • Vacuum drying of watches, books and injection moulds

Technical details

Setting temperature range+20 to +200 °C
Working temperature rangemin. 5 °C above room temperature to +200 °C
Temperature setting accuracy0.1 °C up to 99.9 °C setpoint temperature, 0.5 °C from 100 °C
Temperature sensorPt100, 4-wire measurement, separate for each thermal shelf
Vacuum range5 to 1,100 mbar, digital pressure control
Permissible ultimate vacuum0.01 mbar
Maximum leak rate0.01 bar/h
Vacuum connectionSmall flange DN16, gas inlet with fresh air supply
Internal volume29 l
Internal dimensions (W x H x D)385 x 305 x 250 mm
External dimensions (W x H x D)550 x 607 x 400 mm (depth plus 38 mm door handle)
Net weightapprox. 55 kg
Gross weight incl. cartonapprox. 76 kg
Carton dimensions (W x H x D)660 x 870 x 590 mm
Thermal shelves in scope of delivery1
Max. number of shelves2
Max. load per shelf20 kg
Max. load per unit40 kg
Thermal shelf connection1 connection in the rear wall
ControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic display
Timerdigital countdown clock, 1 minute to 99 days
InterfacesEthernet LAN, USB
Connection voltage230 V, 50/60 Hz
Permissible ambient temperature+5 to +40 °C
Permissible humiditymax. 80 % rel., non-condensing
Overvoltage category / pollution degreeII / 2
MarkingsCE, VDE, cMETus

Other sizes in the series

The VO series comprises three sizes from 29 to 101 litres, all with TwinDISPLAY, sorted by internal volume:

ModelInternal volumeSetting temperaturePressure range
VO29 (this page)29 l+20 to +200 °C5 to 1,100 mbar
VO4949 l+20 to +200 °C5 to 1,100 mbar
VO101101 l+20 to +200 °C5 to 1,100 mbar

Scope of delivery

  • 1x Memmert Vacuum drying oven VO29
  • 1 thermal shelf made of aluminium (material 3.3547) with integrated large-area heating
  • Factory calibration certificate for +160 °C at 20 mbar pressure for every supplied thermal shelf
  • Full-view glass door, spring-mounted 15 mm thick safety glass on the inside, splinter-protection pane on the outside

Regulatory information

The unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal.

Individual requirements and procurement service

Available as factory options for the VO29 are the Premium module T5 (including inert gas switching), the current interface V6 (4 to 20 mA, temperature of a Pt100 that can be freely positioned in the interior, price per sensor, only with T5), the potential-free contact H6 to NAMUR NE 28 for fault messages and MobileALERT C3 for alarm notification by SMS (requires H6). Accessories include additional thermal shelves made of anodised aluminium (B00741) or stainless steel 1.4404 (B00733), the vacuum pump E07509 with signal cable and hose, the pump module PM29 or PMP29 with base frame B63505, USB-Ethernet adapter, Ethernet cable (5 m), USB user ID stick and the FDA licence FDAQ1 for AtmoCONTROL FDA. Services range from factory calibration (+50, +100 and +160 °C at 20 mbar) and IQ/OQ documents to short training, maintenance and an on-site maintenance contract. For individual requirements, we will advise you personally.

Volume: 29 l
Skip product gallery

Matching accessories

Memmert tubular steel base frame B63505 for vacuum drying oven VO29
Manufacturer number: B63505

The base frame B63505 is made of tubular steel and painted black. It is intended for the stacking unit consisting of vacuum drying oven VO29 and pump module.According to Memmert, the total height of this stacking unit is 1,650 mm.Typical applicationsThe stacking unit consisting of the VO29 and a pump module is placed on the base frame. Typical uses of the VO29:Vacuum drying of foodstuffs and cosmeticsDrying of granules and powders in vacuum cyclesDrying of printed circuit boards and electronic componentsSuitable forModelSizeInterior volume (l)VO292929Technical detailsMaterialTubular steelSurfacepainted blackTotal height of the stacking unit according to Memmert1,650 mmScope of delivery1 tubular steel base frame, painted blackIndividual requirements & procurement serviceFor further accessories for the VO29 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €314.76
memmert thermoblech
Memmert stainless steel 1.4404 thermal shelf B00733 for vacuum drying oven VO29
Manufacturer number: B00733

The thermal shelf B00733 is made of stainless steel, material 1.4404 (ASTM 316 L), and intended for particularly corrosive materials. It serves as an additional heated shelf in the interior. It is intended for the VO29 vacuum drying oven and, according to Memmert, can bear a maximum of 20 kg per thermal shelf.It has integrated large-area heating with on-site sensors (Pt100, 4-wire measurement) and a shelf-specific overtemperature protection (Multi-Level-Overtemperature-Control). According to Memmert, a calibration certificate is only possible when ordering a new unit. The anodised aluminium thermal shelf is also available (B00741). The image is for illustration only.Typical applicationsTypical uses of the VO29 vacuum drying oven:Drying of granules and powders in vacuum cyclesDrying of printed circuit boards and electronic componentsVacuum drying of watches, books and injection mouldsSuitable forModelSizeInterior volume (l)VO292929Technical detailsMaterialStainless steel, material 1.4404 (ASTM 316 L)Heatingintegrated large-area heatingSensorsPt100, 4-wire measurementOvertemperature protectionshelf-specific, Multi-Level-Overtemperature-ControlMaximum load according to Memmert20 kg per thermal shelfScope of delivery1 thermal shelf made of stainless steel, material 1.4404, with integrated large-area heatingIndividual requirements & procurement serviceFor the aluminium thermal shelf, for further accessories for the VO29 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €515.14
memmert thermoblech
Memmert aluminium thermal shelf B00741 for vacuum drying oven VO29
Manufacturer number: B00741

The thermal shelf B00741 is made of anodised aluminium (material 3.3547, ASTM B209). It serves as an additional heated shelf in the interior. It is intended for the VO29 vacuum drying oven and, according to Memmert, can bear a maximum of 20 kg per thermal shelf.It has integrated large-area heating with on-site sensors (Pt100, 4-wire measurement) and a shelf-specific overtemperature protection (Multi-Level-Overtemperature-Control). According to Memmert, a calibration certificate is only possible when ordering a new unit. For particularly corrosive materials, the thermal shelf made of stainless steel 1.4404 is also available (B00733). The image is for illustration only.Typical applicationsTypical uses of the VO29 vacuum drying oven:Vacuum drying of foodstuffs and cosmeticsDrying of printed circuit boards and electronic componentsVacuum drying of watches, books and injection mouldsSuitable forModelSizeInterior volume (l)VO292929Technical detailsMaterialAluminium, anodised, material 3.3547 (ASTM B209)Heatingintegrated large-area heatingSensorsPt100, 4-wire measurementOvertemperature protectionshelf-specific, Multi-Level-Overtemperature-ControlMaximum load according to Memmert20 kg per thermal shelfScope of delivery1 anodised aluminium thermal shelf with integrated large-area heatingIndividual requirements & procurement serviceFor the stainless steel thermal shelf, for further accessories for the VO29 vacuum drying oven and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €515.14
Memmert vacuum connecting hose B04026, 3 m, for vacuum drying oven VO 29, 49 and 101
Manufacturer number: B04026

The vacuum connecting hose B04026 is 3 m long and connects the vacuum drying oven to the Memmert pump. Optimised connection accessories, some of which are made of stainless steel, are included.It is not required if a pump module with pump is ordered or already available. According to Memmert, the vacuum connection on the rear of the unit is connected via the connecting hose to the vacuum pump connection of the pump module or of another suitable vacuum pump. The table shows the compatible VO vacuum drying ovens.Typical applicationsTypical uses in the compatible units:Drying food and cosmetics under vacuum, for example in the VO49Drying printed circuit boards and electronic components, for example in the VO49Vacuum drying of watches, books and injection moulds, for example in the VO29Suitable forModelSizeInterior volume (l)VO292929VO494949VO101101101Technical detailsLength3 mConnection accessoriesoptimised, partly made of stainless steelScope of delivery1 vacuum connecting hose, 3 m, with connection accessoriesIndividual requirements & procurement serviceFor the signal cable for pump control, for questions about the pump module and about connecting another vacuum pump, our procurement service accepts enquiries.

Manufacturer's RRP: €225.32
Memmert signal cable B39410, 3 m, for pump control, for vacuum drying oven VO 29, 49 and 101
Manufacturer number: B39410

The signal cable B39410 is 3 m long. It is used for speed control and for optimising the pump performance by activating flushing cycles of the Memmert pump as required. It is not required if a pump module is ordered or already available.According to Memmert, when drying goods with a high moisture content, the pump performance can decline due to condensation in the pump heads. Brief flushing with fresh air clears the diaphragms. According to Memmert, the demand-controlled speed regulation saves energy and protects the pump diaphragms. The table shows the compatible VO vacuum drying ovens.Typical applicationsTypical uses in the compatible units:Drying granules and powder in vacuum cycles, for example in the VO29Drying larger quantities of powder or granules in vacuum cycles, for example in the VO101Vacuum drying of food and cosmetics, for example in the VO29Suitable forModelSizeInterior volume (l)VO292929VO494949VO101101101Technical detailsLength3 mScope of delivery1 signal cable, 3 mIndividual requirements & procurement serviceFor the vacuum connecting hose, for questions about the pump module and about controlling another vacuum pump, our procurement service accepts enquiries.

Manufacturer's RRP: €167.70