Skip to main content Skip to search Skip to main navigation

Memmert UF30 universal oven, 32 l, +20 to +300 °C, SingleDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert UF30 universal oven, 32 l, +20 to +300 °C, SingleDISPLAY"

With an internal capacity of 32 litres, the Memmert UF30 universal oven is the smallest model in the UF series and has compact external dimensions of 585 x 704 x 434 mm. Featuring forced air circulation and a temperature range of +20 to +300 °C, it is suitable for drying and heating processes involving individual samples or small batches where floor space is limited but the temperature inside the chamber must still be evenly distributed.

Design and air circulation

An electronically controlled, low-noise air turbine circulates the air within the chamber; its speed can be adjusted in 10 % increments. Preheated fresh air is introduced via an electronically adjustable exhaust air damper; the exhaust air outlet with throttle valve can also be controlled electronically. The low-maintenance interior is reinforced with deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system; the housing has a fully galvanised sheet steel rear panel.

Control via the ControlCOCKPIT

The UF30 is controlled via a ControlCOCKPIT featuring a high-resolution TFT colour graphic display and a DIN Class A Pt100 sensor in a 4-wire configuration. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C onwards. The SetpointWAIT function only starts the process time once the setpoint temperature has actually been reached; a digital countdown timer covers target times ranging from 1 minute to 99 days. Three freely selectable temperature values can be calibrated, whilst a self-diagnostic system assists with troubleshooting. The programme sequence is saved in the event of a power failure, and the data logger can be read out and managed via the Ethernet interface.

Safety according to DIN 12880

A mechanical temperature limiter, protection class 1 according to DIN 12880, switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature. The door is fully insulated and fitted with a two-point locking mechanism as a compression door lock. The permissible ambient temperature is +5 °C to +40 °C with a maximum relative humidity of 80 % (non-condensing), and the cabinet may be installed at altitudes of up to 2,000 m above sea level. The cabinet must only be transported in an upright position.

Selection guide for the correct size

The scope of delivery includes a stainless steel grid shelf and up to three possible shelves; the UF30 is designed for small to medium sample quantities; a total load of up to 60 kg and 20 kg per shelf are permitted. Those who regularly wish to dry or temper multiple batches simultaneously will find greater internal volume in the UF55 (53 l) or the UF75 (74 l), as shown in the size table below.

Typical applications

With an internal volume of 32 litres, the UF30 is suitable for drying, heating, tempering, ageing, baking, testing and curing in research, science, industry and quality assurance.

  • Drying small sample batches in laboratory settings
  • Tempering and curing of individual material samples
  • Preparing and baking small components in quality assurance
  • Ageing and testing small samples in research and quality assurance

Technical details

Setting temperature range+20 to +300 °C
Working temperature rangeat least 10 °C above room temperature up to +300 °C
Temperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °C
Temperature sensor1x Pt100, DIN Class A, 4-wire measurement
Internal volume32 l
Internal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)
External dimensions of housing (W x H x D)585 x 704 x 434 mm
Net weightapprox. 45 kg
Connection 230 V50/60 Hz, approx. 1,600 W
Connection 115 V50/60 Hz, approx. 1,600 W
Shelves max.3
Shelves included in scope of delivery1
Max. load on unit60 kg
Max. load per shelf20 kg
Interiordeep-drawn ribbed, 4-sided all-round heating
ControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic display
Permissible ambient temperature+5 °C to +40 °C
Permissible relative humiditymax. 80 % rel., non-condensing
Maximum installation altitude2,000 m
MarkingsCE, VDE GS, UL, EAC

Other sizes in the series

The UF series with SingleDISPLAY ranges from 32 to 1,060 litres internal volume, sorted by internal volume:

ModelInternal volumeSet temperatureDisplay
UF30 (this page)32 l+20 to +300 °CSingleDISPLAY
UF5553 l+20 to +300 °CSingleDISPLAY
UF7574 l+20 to +300 °CSingleDISPLAY
UF110108 l+20 to +300 °CSingleDISPLAY
UF160161 l+20 to +300 °CSingleDISPLAY
UF260256 l+20 to +300 °CSingleDISPLAY
UF450449 l+20 to +300 °CSingleDISPLAY
UF750749 l+20 to +300 °CSingleDISPLAY
UF10601,060 l+20 to +300 °CSingleDISPLAY

This model is also available with two temperature sensors and two control displays for redundant monitoring in the UF-plus series: UF30plus.

Scope of delivery

  • 1x Memmert UF30 universal oven
  • Factory calibration certificate (calibrated at +160 °C)
  • Fully insulated stainless steel door with 2-point locking (compression door lock)
  • 1x stainless steel grid shelf, electropolished

Regulatory information

This appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and Disposal page.

Installation in a wall opening

For fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29728) or without air slots (B29729). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.

Individual requirements and procurement service

For the UF30, the following items, amongst others, can be ordered ex-works: a full-view glass door, interior lighting and a socket, as well as a gas-tight version. Accessories available include additional shelves and perforated panels, drip trays, a wall bracket, a USB-to-Ethernet adapter and a stacking kit. For qualification and maintenance, we arrange calibration, IQ/OQ/PQ and maintenance services. Should you have specific requirements or any questions regarding the appropriate equipment, we will be happy to advise you personally.

Certification marks: GS (VDE)
Volume: 32 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E28884 for size 30
Manufacturer number: E28884

The E28884 stainless steel grid is an electropolished shelf for 19 Memmert models in size 30. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example UF30 or UN30.All 19 models have 1 grid as standard and can hold up to 3 grids. According to Memmert, the load per shelf is 20 kg. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Tempering and curing of individual material samples, for example in the UF30Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorSuitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)UF30132032UN30132032UF30plus132032UN30plus132032IF30plus132032IN30plus132032IF30132032IN30132032UN30pa132032IPP30132032IPP30plus132032IN30m132032IN30mplus132032IF30m132032IF30mplus132032UN30m132032UN30mplus132032UF30m132032UF30mplus132032The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel grid, electropolished (E28884)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €55.04
memmert rohrverlaengerung gerade
Memmert straight slip-on pipe extension B29718 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29718

The straight slip-on pipe extension B29718 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The angled version is also available (B29719). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorTempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Drying and tempering of large, heavy components in industrial manufacturing, for example in the UF1060Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 straight slip-on pipe extensionIndividual requirements & procurement serviceFor the angled version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €41.28
memmert rohrverlaengerung gewinkelt
Memmert angled slip-on pipe extension B29719 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29719

The angled slip-on pipe extension B29719 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The straight version is also available (B29718). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Parallel drying of several sample batches in a confined space, for example in the UN75Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material samples in series, for example in the UN260Testing and curing of larger components in quality assurance, for example in the UF750Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 angled slip-on pipe extensionIndividual requirements & procurement serviceFor the straight version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €108.36
memmert untergestell nivellierbar
Memmert levelling base frame B29745, height 600 mm, for size 30
Manufacturer number: B29745

The levelling base frame B29745 has a height of 600 mm and is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. The size corresponds to the number in the unit name, for example UF30 or UN30.A flat base frame with a height of 130 mm is also available (B33657). The mobile version with a height of 660 mm is also available (B29746). The image is for illustration only.Typical applicationsUnits of size 30 are placed on the base frame. Typical uses of these units:Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorDrying and heating in industrial quality assurance, for example in the UN30plusMicrobiological cooled incubation in the IPP30 Peltier cooling incubatorSample preparation in pathology and histology in the UN30pa paraffin ovenWhen installing, the clearances of the unit apply; for the UN30 universal oven, at least 15 cm wall clearance, 20 cm ceiling clearance and 5 cm side clearance.Suitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsHeight600 mmScope of delivery1 levelling base frame, height 600 mmIndividual requirements & procurement serviceFor the flat and the mobile version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €266.60
Memmert levelling feet B29768, set of 4, for sizes 30, 55, 75, 110, 160 and 260
Manufacturer number: B29768

The B29768 set of levelling feet contains 4 pieces. With levelling feet, the unit can be aligned horizontally.The set is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco and HPPeco series in sizes 30, 55, 75, 110, 160 and 260. The table of compatible models shows which series is available in which size. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorEmbedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenParallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoSuitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574UN160pa160161IF30plus3032IN30plus3032IF303032IN303032IF160160161IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UN55pa5553UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032IPP260eco260256IPP260ecoPlus260256HPP110eco110108HPP260eco260256IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF160TS160161UF260TS260256Scope of delivery1 set of levelling feet (4 pieces)Individual requirements & procurement serviceFor base frames, further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €46.44
Memmert stacking kit B29744 for sizes 30, 50, 55, 75, 105 and 110
Manufacturer number: B29744

The B29744 stacking kit consists of 4 pieces and is intended for stacking units of the same size. It is intended for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco, HCP and IFbw series in sizes 30, 50, 55, 75, 105 and 110. The size corresponds to the number in the unit name, for example UF30 or UN30.Separate stacking kits are also available for HCP150, HCP240 and for ICO50, 180 and 240 (B42114, B48129, B68362 and B64732). The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorIncubating several sample series at the same time in research and medicine, for example in the IF110Environmental tests and environmental simulations in the HCP105 humidity chamberSuitable forModelSizeInterior volume (l)IF110bw110108UF303032IF110110108UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574IF30plus3032IN30plus3032IF303032IN303032IF55plus5553IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574UN55pa5553UF110plus110108UN110110108UN110plus110108IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032HPP110eco110108HCP505056HCP105105107IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108Scope of delivery1 stacking kit (4 pieces)Individual requirements & procurement serviceFor the stacking kits for HCP humidity chambers and ICO CO₂ incubators, for base frames and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €61.92
Memmert Wandkonsole
Memmert wall bracket B29755 for size 30
Manufacturer number: B29755

The wall bracket B29755 is intended for wall mounting of Memmert units in the I, Im, U, UNpa and Um series in size 30. The table of compatible models shows which series is available in this size. The image is a Memmert drawing and is for illustration only. The size corresponds to the number in the unit name, for example IF30 or IN30.Typical applicationsTypical uses in the compatible units:Incubation of individual samples in research and medicine, for example in the IF30Drying small sample series in laboratory operation, for example in the UN30plusEmbedding and heating of paraffin or other embedding media for histology, for example in the UN30paSuitable forModelSizeInterior volume (l)IF303032IN303032IF30plus3032IN30plus3032IF30m3032IN30m3032IF30mplus3032IN30mplus3032UF303032UN303032UF30plus3032UN30plus3032UN30pa3032UF30m3032UN30m3032UF30mplus3032UN30mplus3032Scope of delivery1 wall bracket for wall mountingIndividual requirements & procurement serviceFor questions about wall mounting and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €231.34
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68506 for size 30
Manufacturer number: B68506

The B68506 stainless steel perforated tray is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example UF30 or UN30. The image is for illustration only.According to Memmert, the maximum load per shelf for this size is 20 kg. In addition, the maximum load per unit limits the loading; it is stated in the unit’s data sheet.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Tempering and curing of individual material samples, for example in the UF30Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsMaterialStainless steelLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €103.20
memmert untergestell fahrbar
Memmert mobile base frame B29746, height 660 mm, for size 30
Manufacturer number: B29746

The mobile base frame B29746 is 660 mm high.It is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. The levelling version with a height of 600 mm is also available (B29745), as is a flat base frame with a height of 130 mm (B33657). The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsUnits of size 30 are placed on the base frame. Typical uses of these units:Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorDrying and heating in industrial quality assurance, for example in the UN30plusMicrobiological cooled incubation in the IPP30 Peltier cooling incubatorSample preparation in pathology and histology in the UN30pa paraffin ovenWhen installing, the clearances of the unit apply; for the UN30 universal oven, at least 15 cm wall clearance, 20 cm ceiling clearance and 5 cm side clearance.Suitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsHeight660 mmScope of delivery1 mobile base frame, height 660 mmIndividual requirements & procurement serviceFor the flat and the levelling version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €389.58
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02070 for size 30
Manufacturer number: B02070

The B02070 slide-in drip tray is made of stainless steel and has a 15 mm rim. It is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30 and collects dripping liquid. According to Memmert, the maximum load per slide-in drip tray for this size is 1.5 kg. The size corresponds to the number in the unit name, for example UF30 or UN30.In addition, according to Memmert, it can impair the spatial temperature distribution. The base drip tray for the same unit size is also available (B04356). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying smaller sample quantities and laboratory glassware on the laboratory bench, for example in the UN30Embedding and heating paraffin or other embedding media for histology, for example in the UN30pa paraffin ovenSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert1.5 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €67.94
memmert boden abtropfschale
Memmert stainless steel base drip tray B04356 for size 30
Manufacturer number: B04356

The stainless steel base drip tray B04356 is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. It has a 15 mm rim and collects dripping liquid. Memmert states a maximum load of 1.5 kg per base drip tray. The size corresponds to the number in the unit name, for example UF30 or UN30.According to Memmert, it can impair the spatial temperature distribution. The slide-in drip tray for the same unit size is also available (B02070). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying smaller sample quantities and laboratory glassware on the laboratory bench, for example in the UN30Embedding and heating paraffin or other embedding media for histology, for example in the UN30pa paraffin ovenSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert1.5 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €103.20
Memmert levelling base frame B33657, height 130 mm, for size 30
Manufacturer number: B33657

The levelling base frame B33657, with a height of 130 mm, is the flat version for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. It fits 19 models of this size. The size corresponds to the number in the unit name, for example UF30 or UN30.The base frame B29745 with a height of 600 mm is also available for this size.Typical applicationsUnits of size 30 are placed on the base frame. Typical uses of these units:Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorDrying and heating in industrial quality assurance, for example in the UN30plusMicrobiological cooled incubation in the IPP30 Peltier cooling incubatorSample preparation in pathology and histology in the UN30pa paraffin ovenSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsHeight130 mmScope of delivery1 levelling base frame, height 130 mmIndividual requirements & procurement serviceFor the taller version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €208.98