Memmert levelling base frame B33657, height 130 mm, for size 30

With an internal capacity of 32 litres, the Memmert UF30 universal oven is the smallest model in the UF series and has compact external dimensions of 585 x 704 x 434 mm. Featuring forced air circulation and a temperature range of +20 to +300 °C, it is suitable for drying and heating processes involving individual samples or small batches where floor space is limited but the temperature inside the chamber must still be evenly distributed.Design and air circulationAn electronically controlled, low-noise air turbine circulates the air within the chamber; its speed can be adjusted in 10 % increments. Preheated fresh air is introduced via an electronically adjustable exhaust air damper; the exhaust air outlet with throttle valve can also be controlled electronically. The low-maintenance interior is reinforced with deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system; the housing has a fully galvanised sheet steel rear panel.Control via the ControlCOCKPITThe UF30 is controlled via a ControlCOCKPIT featuring a high-resolution TFT colour graphic display and a DIN Class A Pt100 sensor in a 4-wire configuration. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C onwards. The SetpointWAIT function only starts the process time once the setpoint temperature has actually been reached; a digital countdown timer covers target times ranging from 1 minute to 99 days. Three freely selectable temperature values can be calibrated, whilst a self-diagnostic system assists with troubleshooting. The programme sequence is saved in the event of a power failure, and the data logger can be read out and managed via the Ethernet interface.Safety according to DIN 12880A mechanical temperature limiter, protection class 1 according to DIN 12880, switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature. The door is fully insulated and fitted with a two-point locking mechanism as a compression door lock. The permissible ambient temperature is +5 °C to +40 °C with a maximum relative humidity of 80 % (non-condensing), and the cabinet may be installed at altitudes of up to 2,000 m above sea level. The cabinet must only be transported in an upright position.Selection guide for the correct sizeThe scope of delivery includes a stainless steel grid shelf and up to three possible shelves; the UF30 is designed for small to medium sample quantities; a total load of up to 60 kg and 20 kg per shelf are permitted. Those who regularly wish to dry or temper multiple batches simultaneously will find greater internal volume in the UF55 (53 l) or the UF75 (74 l), as shown in the size table below.Typical applicationsWith an internal volume of 32 litres, the UF30 is suitable for drying, heating, tempering, ageing, baking, testing and curing in research, science, industry and quality assurance.Drying small sample batches in laboratory settingsTempering and curing of individual material samplesPreparing and baking small components in quality assuranceAgeing and testing small samples in research and quality assuranceTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangeat least 10 °C above room temperature up to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor1x Pt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 1,600 WShelves max.3Shelves included in scope of delivery1Max. load on unit60 kgMax. load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe UF series with SingleDISPLAY ranges from 32 to 1,060 litres internal volume, sorted by internal volume:ModelInternal volumeSet temperatureDisplayUF30 (this page)32 l+20 to +300 °CSingleDISPLAYUF5553 l+20 to +300 °CSingleDISPLAYUF7574 l+20 to +300 °CSingleDISPLAYUF110108 l+20 to +300 °CSingleDISPLAYUF160161 l+20 to +300 °CSingleDISPLAYUF260256 l+20 to +300 °CSingleDISPLAYUF450449 l+20 to +300 °CSingleDISPLAYUF750749 l+20 to +300 °CSingleDISPLAYUF10601,060 l+20 to +300 °CSingleDISPLAYThis model is also available with two temperature sensors and two control displays for redundant monitoring in the UF-plus series: UF30plus.Scope of delivery1x Memmert UF30 universal ovenFactory calibration certificate (calibrated at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and Disposal page.Individual requirements and procurement serviceFor the UF30, the following items, amongst others, can be ordered ex-works: a full-view glass door, interior lighting and a socket, as well as a gas-tight version. Accessories available include additional shelves and perforated panels, drip trays, a wall bracket, a USB-to-Ethernet adapter and a stacking kit. For qualification and maintenance, we arrange calibration, IQ/OQ/PQ and maintenance services. Should you have specific requirements or any questions regarding the appropriate equipment, we will be happy to advise you personally.

The Memmert UN30 universal oven is the most compact model in the Memmert universal oven range and operates using purely natural convection rather than an active air turbine. With an internal volume of 32 litres, a temperature range of 20 to 300 °C and a unit weight of around 45 kg, it fits on a laboratory bench, where space is usually more limited than in the equipment area of a permanent laboratory. As there is no active air circulation inside the chamber, the UN30 is particularly suitable for applications where vibration-free and low-dust operation are more important than the shortest possible heating time, such as when gently drying light samples or fine powders.Natural convection for vibration-free, low-dust operationUnlike the UF models in the series, the Memmert UN30 universal oven deliberately does not feature an air turbine or a recirculation motor. Heat rises within the chamber purely by convection, without a fan setting air, dust or light sample components in motion. As a result, the operating temperature range starts from at least 5 °C above room temperature up to 300 °C, whilst the forced-air models in the UF series only start from 10 °C above room temperature; however, thanks to forced air circulation, they heat up more quickly and distribute the temperature more actively. For samples that are sensitive to air movement, such as loose powders, fine fibres or specimens that must not be blown away by draughts, the UN30’s natural convection is suitable. A DIN Class A Pt100 temperature sensor with 4-wire measurement ensures the same setting accuracy as in the larger models, despite the simpler airflow principle: 0.1 °C to 99.9 °C and 0.5 °C from 100 °C.ControlCOCKPIT SingleDISPLAY: compact operation with a full range of functionsDespite its compact design, the UN30 does not compromise on any of the control functions found in the larger models. The ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a TFT colour graphic display, regulates temperature in Celsius or Fahrenheit, as well as the position of the exhaust air damper, programme duration, time zone and summer/winter time. As no air turbine is fitted, the only parameter omitted is that for the recirculation fan speed. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWAIT function only starts the process time once the setpoint temperature has been reached. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download, whilst a USB stick containing the full version is available as an optional accessory.Compact dimensions of the Memmert UN30 universal ovenThe internal dimensions are 400 x 320 x 250 mm, whilst the external dimensions are 585 x 704 x 434 mm. One electropolished stainless steel grid shelf is included as standard; the cabinet can accommodate up to three shelves in total. The maximum load capacity is 60 kg for the entire unit and 20 kg per shelf, which is entirely sufficient for smaller sample batches and individual containers. As with the larger models, the interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The fully insulated stainless steel door locks via a 2-point compression door lock. The UN30 is connected to a 230 V or 115 V supply, in each case at 50/60 Hz, with a power consumption of around 1,600 W.Selection guide: choosing the right size from the UN seriesThe Memmert universal oven series with natural convection covers a range of internal volumes from 32 to 749 litres. The UN30 is the smallest model in the range. When choosing the right size, the key factors, apart from internal volume, are the footprint and the number of shelves required; not every larger model takes up more floor space than the next smaller one.ModelInternal volumeUN3032 l, footprint 585 x 434 mm, max. 3 shelvesUN5553 l, footprint 585 x 514 mm, max. 4 shelvesUN7574 l, footprint 585 x 514 mm, max. 6 shelvesUN110108 l, footprint 745 x 584 mm, max. 5 shelvesUN260256 l, footprint 824 x 684 mm, max. 9 shelvesUN450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUN750749 l, footprint 1,224 x 784 mm, max. 14 shelvesThe UN30 is suitable when space on the laboratory bench is limited and only a few samples are being processed at a time. If the number of samples increases, the Memmert UN55 universal oven is the obvious next size up, offering 53 litres instead of 32 and 4 shelves instead of 3, whilst taking up only slightly more floor space. All seven sizes in the series can be found in our range of climate chambers and incubators.Distinction: TwinDISPLAY and the forced-air versionWithin the UN30 series, the most important purchasing decision is between SingleDISPLAY and TwinDISPLAY. The UN30 described here operates with a single Pt100 sensor and one display; for unattended processes with higher safety requirements, the Memmert UN30plus universal oven offers two redundant Pt100 sensors as well as two TFT displays instead of one. Those who would instead prefer to benefit from the shorter heating-up time offered by active air circulation and do not require vibration-free operation will find the Memmert UF30 universal oven to be the equivalent model featuring forced air circulation rather than natural convection, whilst retaining the same internal volume of 32 litres.Safety according to DIN 12880, even in the smallest modelThe UN30 also features adjustable electronic temperature monitoring plus a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature reaches approximately 20 °C above the maximum cabinet temperature. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. CE and EAC markings, as well as a UL test mark, are present.Application, installation and disposalThe same installation rules apply to the Memmert UN30 universal oven when placed on a laboratory bench as for the larger models in the series: a minimum clearance of 15 cm from the wall, a minimum clearance of 20 cm from the ceiling, and a minimum clearance of 5 cm on each side from a wall or adjacent unit. It may be installed at altitudes of up to 2,000 m above sea level at ambient temperatures of 5 °C to 40 °C and a maximum relative humidity of 80 %, non-condensing. Electrically, the UN30 is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The interior, made of easy-to-clean stainless steel, can be cleaned using standard laboratory cleaning products. As an electrical appliance, the UN30 is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste; see Regulatory information below.Typical applicationsThe compact Memmert UN30 universal oven is suitable wherever space is limited or where vibration-free, low-dust heat treatment is more important than a short heating-up time.Drying small sample quantities and laboratory glassware on the laboratory benchVibration-free drying of dust- or air-sensitive samplesTempering, ageing and baking of small material samplesRoutine tests in quality assurance, schools and trainingA compact addition or secondary unit in laboratories with limited spaceInvestment rationale: keep it compact or opt for greater safety straight awayThe UN30 is supplied with 1 electropolished stainless steel grid shelf; the cabinet is designed to accommodate up to 3 shelves. For day-to-day operation under supervision, the SingleDISPLAY of the UN30 described here is generally sufficient. If a process runs unattended overnight, the redundant sensor system of the Memmert UN30plus universal oven reduces the risk of an undetected sensor failure. For visual inspection without opening the door, a full-view glass door with 4-layer insulation up to 250 °C or 300 °C is available as an option, as are interior lighting and a stacking kit, which allows two UN30 units to be stacked on top of one another to save space. Anyone wishing to use the data logger permanently, rather than just with the time-limited trial version, should add an AtmoCONTROL software licence. For pharmaceutical or standards-compliant applications, we arrange calibration, IQ/OQ and maintenance services, including DAkkS calibration on request.Frequently asked questions before purchaseDoes the UN30 fit on a standard laboratory bench?Yes, with a net weight of around 45 kg and external dimensions of 585 x 704 x 434 mm, the UN30 is designed for use on a laboratory bench, provided that the bench can safely support the load.How many samples can fit into the UN30 at once?One grid shelf is included as standard; up to 3 shelves, each with a maximum load of 20 kg, are possible, giving a total load capacity of up to 60 kg.Is natural convection sufficient for uniform drying?For most routine applications, yes. For dust- or air-sensitive samples, the gentle natural convection of the UN30 is an advantage; for shorter heating times with larger batches, the Memmert UF30 universal oven offers active air circulation with the same volume.How does the UN30 differ from the UN30plus?Both operate using natural convection and share the same housing; the UN30plus additionally features two redundant Pt100 sensors and TwinDISPLAY for greater process reliability during unattended operation.What is the accuracy of the temperature control?0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards, as the UN30, like all models in the series, measures using a DIN Class A Pt100 sensor with 4-wire technology.Can a glass door be retrofitted?A full-view glass door with 4-layer insulation up to 250 °C or 300 °C is one of the standard options for the UN30 and can be specified when ordering.Is the UN30 suitable for continuous overnight operation?The mechanical temperature limiter, which complies with protection class 1 according to DIN 12880, switches off the heating in the event of an overtemperature of approximately 20 °C and is designed for unattended operation.Technical detailsAdjustable temperature range20 to 300 °CWorking temperature rangeat least 5 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 1,600 WShelves max.3Shelves included in scope of delivery1Max. load on unit60 kgMax. load per shelf20 kgInterior materialStainless steel, 4-sided all-round heatingCasing materialTextured stainless steel, galvanised sheet steel rear panelControl systemControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayTimer1 minute to 99 days, digital countdown timerPermissible ambient temperature5 °C to 40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation altitude2,000 mMarkingsCE, EAC, UL test markScope of delivery1x Memmert UN30 universal ovenFactory calibration certificate (calibrated at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert UN30 universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Individual requirements & procurement serviceOptions available for the UN30 include full-view glass doors with 4-layer insulation up to 250 °C or 300 °C, interior lighting, reinforced grid shelves and perforated sheets, slide-in or floor-standing drip trays, as well as wall brackets, levelling feet, stacking kits and a mobile or fixed base frame. For data acquisition, a USB-to-Ethernet adapter with a 5 m cable, user ID sticks and AtmoCONTROL software licences are available. In addition, we arrange calibration, IQ/OQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories, extended overtemperature protection with an additional Pt100 sensor, or assistance in selecting the right universal oven for your application? Through our procurement service, we will be happy to assist you with procurement and configuration.

The Memmert UF30plus universal oven has the same external dimensions and the same 32-litre interior as the base model UF30, but works with dual sensors: two Pt100 sensors monitor each other, and if one fails, the second automatically takes over the function. In addition there are AutoSAFETY, an adjustable temperature monitor or adjustable temperature limiter selectable on the display, and a visual and audible alarm.Compact housing with dual sensorsExternally, the UF30plus hardly differs from the base model: the same external dimensions, the same easy-care, deep-drawn ribbed 32-litre interior with 4-sided all-round heating, plus an air turbine that is electronically controllable in 10 % steps and the admixture of preheated fresh air via the exhaust air flap. The difference lies in the measurement technology: two DIN class A Pt100 sensors measure in 4-wire technology and back each other up, and if one fails, the process continues with the second sensor.Two displays, one operating conceptThe ControlCOCKPIT TwinDISPLAY works with an adaptive PID microprocessor controller and two high-resolution TFT colour graphic displays. Three freely selectable temperature values can be calibrated, and the setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. Programmes can be created, managed and transferred with AtmoCONTROL via the Ethernet interface or the USB port, and the programme sequence is retained in the event of a power failure. If the process time is to start only after the setpoint temperature has been reached, the SetpointWAIT function does this automatically.Safety concept despite a small chamberThe mechanical temperature limiter of protection class 1 according to DIN 12880 switches off at about 20 °C above the maximum oven temperature. In addition, an adjustable temperature monitor (protection class 3.1) or an adjustable temperature limiter (protection class 2) can be activated on the display. The AutoSAFETY function monitors over- and under-temperature, automatically follows the setpoint at an adjustable distance and reports deviations visually and audibly, and a self-diagnosis system also helps with troubleshooting.Guide to choosing: is the second sensor worth it?For simple drying tasks, the base model UF30 with SingleDISPLAY and one Pt100 sensor is often sufficient. Anyone who needs two sensors that monitor each other, AutoSAFETY and a selectable second temperature monitor chooses the UF30plus. If more volume is needed with the same protection, take a look at the size table below for the UF55plus or UF75plus.Typical applicationsWith 32 litres of internal volume and redundant sensors, the UF30plus is suitable for drying, heating, tempering, ageing, baking, testing and curing in research, science, industry and quality assurance.Drying small batches with redundant temperature measurementTempering and curing small samplesAgeing and testing in quality assuranceBaking and heating small components in research and industryTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 10 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 1,600 WShelves max.3Shelves included in scope of delivery1Max. load of unit60 kgMax. load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsAutoSAFETY, visual and audible alarmPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMax. installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesNine sizes between 32 and 1,060 litres make up the UF-plus series, listed here sorted by internal volume:ModelInternal volumeSetting temperatureDisplayUF30plus (this page)32 l+20 to +300 °CTwinDISPLAYUF55plus53 l+20 to +300 °CTwinDISPLAYUF75plus74 l+20 to +300 °CTwinDISPLAYUF110plus108 l+20 to +300 °CTwinDISPLAYUF160plus161 l+20 to +300 °CTwinDISPLAYUF260plus256 l+20 to +300 °CTwinDISPLAYUF450plus449 l+20 to +300 °CTwinDISPLAYUF750plus749 l+20 to +300 °CTwinDISPLAYUF1060plus1,060 l+20 to +300 °CTwinDISPLAYAnyone who can do without the second sensor will find the same volume with SingleDISPLAY in the UF series: UF30.Scope of delivery1x Memmert universal oven UF30plusFactory calibration certificate (calibration at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.Individual requirements and procurement serviceFor the UF30plus, a full-view glass door, a programmable door lock, door-open detection and a gas-tight version, among other things, can be ordered from the factory. Suitable accessories include additional shelves and perforated trays, a USB Ethernet adapter, a USB user ID stick and AtmoCONTROL software licences. For qualification and maintenance, we arrange calibration, IQ/OQ/PQ and maintenance services. For individual requirements, we will advise you personally.

With 32 litres of interior, the Memmert UN30plus universal oven is the smallest model of the UN-plus series and works without an air turbine, with natural convection alone. The external dimensions are 585 x 704 x 434 mm plus 56 mm for the door handle, and the setting temperature range extends from +20 to +300 °C. Two DIN class A Pt100 sensors monitor each other in 4-wire measurement and automatically take over the function of the other in the event of a fault.Interior and air routing without a fanThe interior measures 400 x 320 x 250 mm, is deep-drawn ribbed and has protected, integrated 4-sided all-round heating. An electronically adjustable exhaust air flap admixes preheated fresh air, and the exhaust air outlet with throttle valve can likewise be controlled electronically. One stainless steel grid shelf, electropolished, is part of the standard equipment, and up to three shelves are possible. A total load of 60 kg is permitted with a maximum of 20 kg per shelf, and the housing has a fully galvanised sheet steel rear wall.Control with TwinDISPLAYThe UN30plus is controlled via the ControlCOCKPIT with two TFT colour graphic displays, and the setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. The SetpointWAIT function starts the process time only when the setpoint temperature has actually been reached, and a digital countdown timer covers target times from 1 minute to 99 days. Three freely selectable temperature values can be calibrated, and a self-diagnosis system supports fault finding. Programming and documentation are done via the Ethernet interface or USB port with the AtmoCONTROL software, and the programme sequence is retained in the event of a power failure.Safety technologyA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at about 20 °C above the maximum oven temperature, and an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can additionally be selected on the display. AutoSAFETY automatically follows the setpoint at a freely selectable distance and triggers a visual and audible alarm in the event of deviation. Unlike the larger models of the series, the UN30plus has no HeatBALANCE function for heating power distribution, but the redundant sensors and AutoSAFETY are already fitted as standard even in this smallest size.Guide to choosing the right sizeIf there is room for a model with one more shelf, the UN55plus with 53 litres and 80 kg permitted total load offers more scope, see the size table below. For individual small samples or light batches, the UN30plus with its compact external dimensions remains the more space-saving choice.Typical applicationsAs a heating and drying oven with natural convection, the UN30plus is used in research, science, industry and quality assurance for drying and heating small sample quantities.Drying small sample series in laboratory operationHeating individual samples in research and scienceDrying and heating in industrial quality assuranceTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 5 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mm (plus 56 mm door handle)Net weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V (factory option)50/60 Hz, approx. 1,600 WShelves max.3Shelves included in scope of delivery1Max. load of unit60 kgMax. load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsAutoSAFETY, visual and audible alarmPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMax. installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe UN-plus series with natural convection comprises eight sizes from 32 to 749 litres, listed below sorted by internal volume:ModelInternal volumeSetting temperatureDisplayUN30plus (this page)32 l+20 to +300 °CTwinDISPLAYUN55plus53 l+20 to +300 °CTwinDISPLAYUN75plus74 l+20 to +300 °CTwinDISPLAYUN110plus108 l+20 to +300 °CTwinDISPLAYUN160plus161 l+20 to +300 °CTwinDISPLAYUN260plus256 l+20 to +300 °CTwinDISPLAYUN450plus449 l+20 to +300 °CTwinDISPLAYUN750plus749 l+20 to +300 °CTwinDISPLAYWith SingleDISPLAY, the same volume is available in the UN series: UN30.Scope of delivery1x Memmert universal oven UN30plusFactory calibration certificate (calibration at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.Individual requirements and procurement serviceFor the UN30plus, the 115 V voltage variant, temperature throttling (factory limit on the maximum adjustable temperature), a full-view glass door, interior lighting and socket and a nearly gas-tight interior, among other things, can be ordered from the factory. Suitable accessories include additional grid shelves and perforated trays, drip trays, a wall bracket, a USB Ethernet adapter and a stacking kit. For qualification, we arrange factory, on-site and DAkkS calibrations, IQ/OQ documentation according to DIN 12880:2007-05 and a short training course. For individual requirements, we will advise you personally.

The Memmert IF30plus incubator is the forced-air version of the compact 32-litre model and thus differs significantly from the natural convection models IN30 and IN55: an electronically controllable air turbine ensures more uniform temperature distribution inside the chamber; a TwinDISPLAY with two screens enhances operation with additional safety and display functions; and a permanently installed sterilisation programme thermally cleans the interior between different sample runs. As with the IN models, the temperature range extends from +20 to +80 °C; however, due to the active air circulation, the working temperature range only begins at a minimum of 10 °C above room temperature, rather than at 5 °C.Forced air circulation for uniform incubation and faster sample changesThe air turbine in the Memmert IF30plus incubator actively distributes heat throughout the interior, rather than simply allowing it to rise naturally, as is the case with the IN models. This is an advantage for applications where culture vessels of different sizes need to be maintained at a similar temperature simultaneously, as well as when switching frequently between different sample types. Two DIN Class A Pt100 sensors in a 4-wire configuration monitor each other in the IF30plus, providing an additional level of safety compared with the single sensor in the IN models. The setting accuracy is 0.1 °C across the entire operating range, from at least 10 °C above room temperature up to 80 °C.ControlCOCKPIT TwinDISPLAY and integrated interior sterilisationThe IF30plus is controlled via the ControlCOCKPIT TwinDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with two high-resolution TFT colour graphic displays. The following can be set: temperature in Celsius or Fahrenheit, the speed of the recirculation fan, the position of the exhaust air flap, programme duration, as well as the time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWAIT function only starts the incubation time once the set temperature has been reached. In the event of a power cut, the unit saves the programme progress to date. Particularly useful for routine microbiological work: a permanently set sterilisation programme running for 4 hours at 160 °C thermally sterilises the interior, though not the samples themselves.Capacity and dimensions of the Memmert IF30plus incubatorThe interior measures 400 x 320 x 250 mm, although the depth is reduced by 39 mm due to the fan; the external dimensions are 585 x 704 x 434 mm, identical to those of the IN30 natural convection model. The scope of delivery includes one electropolished stainless steel grid shelf, and the cabinet can accommodate up to three shelves in total. The maximum load capacity is 60 kg for the entire unit and 20 kg per shelf. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The IF30plus is connected to a 230 V (approx. 1,600 W) or 115 V (approx. 800 W) supply, in each case at 50/60 Hz.Selection guide: natural convection or forced air circulation with TwinDISPLAYMemmert offers two sizes with natural convection for incubation, as well as the IF30plus with forced air circulation and TwinDISPLAY.ModelInternal volume and controlIN3032 l, natural convection, SingleDISPLAY, 3 shelves max.IN5553 l, natural convection, SingleDISPLAY, 4 shelves max.IF30plus32 l, forced air circulation, TwinDISPLAY, 3 shelves max.With the same internal volume as the Memmert IN30 incubator, the IF30plus offers more active air circulation, the TwinDISPLAY and the integrated sterilisation programme. Those who, on the other hand, require a larger capacity with natural convection will find this in the Memmert IN55 incubator with a capacity of 53 litres. The full range can be found at Climate chambers & incubators.Distinction: IF versus IN, TwinDISPLAY versus SingleDISPLAYThe key difference between the IF30plus and the IN models lies in the ventilation principle: The IN series operates using natural convection and is particularly suitable for vibration-free, quiet incubation without air movement, whilst the IF30plus, with its air turbine, offers a more even temperature distribution for culture vessels of varying sizes or those densely packed, but only starts operating from 10 °C above room temperature, rather than 5 °C. The models also differ in terms of their displays: the IF30plus’s TwinDISPLAY, featuring two screens, as well as the integrated ASF over- and under-temperature monitoring and the selectable protection classes TWW or TWB, go beyond the SingleDISPLAY of the IN models. The UN30 universal oven, with natural convection and a temperature range up to 300 °C, is, by contrast, designed for drying tasks rather than incubation, and is not suitable for culture work in the range up to 80 °C.Safety: mechanical limiter, ASF and alarmThe IF30plus is fitted with a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature. Additionally, an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can be selected via the display. The integrated ASF over- and under-temperature monitoring system automatically tracks the setpoint at a freely selectable interval and triggers a visual and audible alarm if the temperature falls below or exceeds the setpoint; if the temperature is exceeded, the heating is also switched off. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. The unit bears CE and EAC markings as well as a UL test mark.Installation, operation and disposalFor operation, a minimum distance of 15 cm from the wall and a minimum distance of 20 cm from the ceiling must be maintained; a minimum of 5 cm is sufficient on either side in relation to the wall or an adjacent unit. The unit may be installed at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the IF30plus is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The integrated sterilisation programme allows for regular thermal cleaning of the interior between different sample runs, but does not replace regular maintenance. As an electrical appliance, the IF30plus is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste.Typical applicationsWith active air circulation, TwinDISPLAY and an integrated sterilisation programme, the Memmert IF30plus incubator is suitable for more demanding incubation tasks involving frequently changing sample types.Incubation of culture vessels of varying sizes with uniform temperature distributionRoutine microbiological testing involving frequent switching between different sample typesFood analysis with requirements for documented cleaning of interior surfacesPharmaceutical applications with heightened requirements for process safety and alarm systemsResearch requiring redundant temperature monitoring using two Pt100 sensorsInvestment rationale: Targeted expansion of safety and process equipmentThe scope of delivery for the IF30plus includes one electropolished stainless steel grid shelf and the inner glass door; the cabinet is designed to accommodate up to three shelves. Those wishing to secure access can configure a lockable door with a security lock; for additional redundancy in temperature monitoring, a further Pt100 sensor with overtemperature protection is available. If required, the unit can also be monitored via SMS alerts. For pharmaceutical or standards-governed applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request, which are particularly relevant for environments requiring validation, given the additional safety features of the IF30plus.Frequently asked questions before making a purchaseWhat is the integrated sterilisation programme designed for?It thermally sterilises the interior of the IF30plus for 4 hours at 160 °C; it does not sterilise the samples themselves. This is useful for thermally cleaning the cabinet between different sample runs.Why does the working temperature range only start at 10 °C above room temperature?The active air circulation provided by the air turbine requires a slightly greater difference from room temperature than the IN models with natural convection, which operate from as low as 5 °C above room temperature.What does ASF mean in the IF30plus?ASF stands for the integrated over- and under-temperature monitoring system, which automatically tracks the setpoint at a freely selectable interval and, in the event of a deviation, triggers an alarm or switches off the heating.How does the IF30plus differ from the IN30?Both have an internal capacity of 32 litres and identical external dimensions; the IF30plus also features an air turbine, TwinDISPLAY, two Pt100 sensors and an integrated sterilisation programme.Is the IF30plus a medical device?No, the IF30plus is not a medical device; this applies only to the separate m and mplus variants.How many samples can fit inside at the same time?One grid shelf is included as standard; up to three shelves, each with a maximum load of 20 kg, are possible, giving a total load capacity of up to 60 kg.Can the programme continue in the event of a power cut?The appliance saves the programme progress to date in the event of a power cut, so that ongoing processes remain traceable.Technical detailsSetting temperature range+20 to +80 °CWorking temperature rangeat least 10 °C above room temperature up to 80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN Class A, 4-wire measurement, cross-monitoringInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of the housing (W x H x D)585 × 704 × 434 mmNet weightapprox. 48 kgConnected load 230 V50/60 Hz, approx. 1,600 WConnected load 115 V50/60 Hz, approx. 800 WMaximum number of shelves3Shelves included in scope of delivery1Max. load on the unit60 kgMaximum load per shelf20 kgInterior materialsStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displaysSterilisation programmePermanently installed, 4 hours at 160 °C, interior sterilisationTimer1 minute to 99 days, digital countdown clockPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation altitude2,000 mMarkingsCE, EAC, UL test markScope of delivery1x Memmert IF30plus incubatorFactory calibration certificate (calibrated at 37 °C)Fully insulated stainless steel door with a 2-point locking system (compression door lock)Inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert IF30plus incubator is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Individual requirements and procurement serviceThe IF30plus is available with, amongst other features, interior lighting and a power socket, a lockable door with a security lock, an additional Pt100 sensor with over-temperature protection, and SMS alerts. We also arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories or assistance in selecting the right incubator for your application? Through our procurement service, we’d be happy to assist you with procurement and configuration.

With a capacity of 32 litres, the IN30plus is the smallest model in the IN-plus series and comes with one stainless steel grid shelf as standard and holds up to three. Two Pt100 sensors monitor each other and take over the function of the other in the event of a fault. Temperature control is provided within the range of +20 to +80 °C with a setting accuracy of 0.1 °C via a ControlCOCKPIT TwinDISPLAY featuring two TFT colour graphic displays.Compact housing with TwinDISPLAYNatural convection mixes in preheated fresh air via an electronically adjustable exhaust air damper; the exhaust air outlet with throttle valve is electronically controllable. The interior features deep-drawn ribbing with 4-sided all-round heating, whilst the housing has a fully galvanised sheet steel rear panel. A model of the same size with forced air circulation instead of natural convection is available in the IF-plus series.Two sensors, one controllerUnlike the other models in the IN-plus series, from the IN55plus to the IN750plus, the IN30plus does not have the HeatBALANCE function for distributing heating output. Programmes are programmed, managed and transferred via Ethernet or USB using the AtmoCONTROL software; SetpointWAIT only starts the process time once the setpoint temperature has been reached.Temperature monitoring and sterilisation programmeA mechanical temperature limiter of protection class 1 according to DIN 12880 forms the first level of protection and cuts off at approximately 20 °C above the maximum cabinet temperature. Additionally, an adjustable temperature monitor (Protection Class 3.1) or an adjustable temperature limiter (Protection Class 2) can be selected; AutoSAFETY tracks the setpoint at a freely selectable interval and signals deviations visually and acoustically. A permanently installed sterilisation programme of 4 hours at 160 °C sterilises the interior, not the load.Selection guide for the right sizeWith a capacity of 32 litres and a maximum of three shelves, the IN30plus is designed for small sample quantities and a compact footprint. If more volume is required, the table below lists the IN55plus with 53 litres, four shelves and the additional HeatBALANCE function.Typical applicationsWith a capacity of 32 litres, the IN30plus is suitable for incubating and temperature-controlling small sample volumes in the range from +20 to +80 °C, including in research applications.Incubation and temperature control of small sample series with redundant sensor monitoringInterior sterilisation via the permanently installed sterilisation programmeUse in researchTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangeAt least 5 °C above room temperature up to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2 Pt100 sensors, DIN Class A, in a 4-wire configuration for mutual monitoring and automatic failover in the event of a faultAdjustable temperature monitor/limiterAdjustable temperature monitor (TWW), protection class 3.1, or adjustable temperature limiter (TWB), protection class 2, selectable via the displayAutoSAFETYadditionally integrated over- and under-temperature monitoring ‘ASF’, automatically tracks the setpoint at a freely selectable interval, alarm if the temperature exceeds or falls below the setpoint, heating shut-off if the setpoint is exceededSterilisation programmePermanently installed sterilisation programme (4 hours/160 °C) for sterilising the interior; not intended for sterilising the loadInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mm (depth plus 56 mm for door handle)Net weightapprox. 48 kgConnected load 230 V50/60 Hz, approx. 1,600 WConnected load 115 V50/60 Hz, approx. 800 WMaximum number of shelves3Shelves included in scope of delivery1InteriorEasy to clean, reinforced with deep-drawn ribbing, with protected, integrated 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displaysPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 % non-condensingMaximum installation altitudemax. 2,000 m above sea levelMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe IN-plus series with TwinDISPLAY ranges from 32 to 749 litres internal volume, sorted by internal volume:ModelInternal volumeSet temperatureDisplayIN30plus (this page)32 l+20 to +80 °CTwinDISPLAYIN55plus53 l+20 to +80 °CTwinDISPLAYIN75plus74 l+20 to +80 °CTwinDISPLAYIN110plus108 l+20 to +80 °CTwinDISPLAYIN160plus161 l+20 to +80 °CTwinDISPLAYIN260plus256 l+20 to +80 °CTwinDISPLAYIN450plus449 l+20 to +80 °CTwinDISPLAYIN750plus749 l+20 to +80 °CTwinDISPLAYThe same capacity is also available with SingleDISPLAY and a Pt100 sensor in the IN series: IN30.Scope of delivery1x Memmert IN30plus incubatorFactory calibration certificate (calibrated at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and Disposal page.Individual requirements and procurement serviceOptions that can be ordered ex-works for the IN30plus include the 115 V voltage at no extra charge, interior lighting, an interior socket and a door-open detection sensor. Optional accessories include a USB User ID stick, a wall bracket, a USB-to-Ethernet adapter and AtmoCONTROL software licences. We arrange calibration and IQ/OQ services for qualification and requalification. We are available to assist you personally with bespoke configurations.

With an internal volume of 32 litres, the Memmert IF30 incubator has the smallest internal volume in the IF series and, with external dimensions of 585 x 704 x 434 mm, takes up a comparatively small amount of floor space. With forced air circulation and a temperature range of +20 to +80 °C, it is suitable for incubating and temperature-controlling individual samples or small batches.Construction and air flowAn electronically controlled air turbine circulates the air inside the interior and can be adjusted in 10 % increments, whilst operating quietly. An electronically adjustable exhaust air damper mixes in preheated fresh air; the exhaust air outlet itself also features an electronically adjustable throttle valve. The interior of the IF30 is reinforced with deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system; the housing has a fully galvanised sheet steel rear panel.Control via the ControlCOCKPITThe IF30 is controlled via a SingleDISPLAY with a high-resolution TFT colour graphics display; the temperature is measured by a DIN Class A Pt100 sensor using a 4-wire measurement. The setting accuracy is 0.1 °C. The SetpointWAIT function ensures that the process time only starts once the setpoint temperature has actually been reached; a digital countdown timer covers target times ranging from 1 minute to 99 days. Three freely selectable temperature values can be calibrated, whilst a self-diagnostic system assists with troubleshooting. The programme sequence remains stored in the event of a power failure, and the data logger can be read out and managed via the Ethernet interface.Safety according to DIN 12880A mechanical temperature limiter, protection class 1 according to DIN 12880, switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature; in addition, the electronic temperature monitoring can be adjusted. The fully insulated stainless steel door with an internal glass door closes with a 2-point locking system as a compression door lock.Guide to choosing the right sizeWith one stainless steel grid shelf in the scope of delivery and up to three possible shelves, the IF30 is designed for small sample quantities; the maximum total load is 60 kg, with 20 kg per shelf. Those who regularly wish to incubate more samples at the same time will find more capacity in the neighbouring IF55 with an internal volume of 53 litres and up to four shelves.Typical applicationsWith an internal volume of 32 litres, the IF30 is suitable as an incubator for incubating and temperature-controlling individual samples or small batches in research, medicine, pharmacy, food analysis and food chemistry.Incubation of individual samples in research and medicineTemperature control of small batches of samples in the pharmaceutical industryIncubation processes in food analysis and food chemistryTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangeat least 10 °C above room temperature up to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1x Pt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of the housing (W x H x D)585 × 704 × 434 mmNet weightapprox. 48 kgConnected load 230 V50/60 Hz, approx. 1,600 WConnected load 115 V (optional)50/60 Hz, approx. 800 WMaximum number of shelves3Shelves included in scope of delivery1Max. load on the unit60 kgMaximum load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation altitude2,000 mMarkingsCE, VDE GS, ULOther sizes in the seriesThe IF series with SingleDISPLAY ranges from 32 to 749 litres in internal volume, listed by internal volume:ModelInternal volumeSetting temperatureDisplayIF30 (this page)32 l+20 to +80 °CSingleDISPLAYIF5553 l+20 to +80 °CSingleDISPLAYIF7574 l+20 to +80 °CSingleDISPLAYIF110108 l+20 to +80 °CSingleDISPLAYIF160161 l+20 to +80 °CSingleDISPLAYIF260256 l+20 to +80 °CSingleDISPLAYIF450449 l+20 to +80 °CSingleDISPLAYIF750749 l+20 to +80 °CSingleDISPLAYThis model is also available in the IF-plus series as the IF30plus, featuring TwinDISPLAY and two Pt100 sensors which monitor each other and take over operation in the event of a fault.Scope of deliveryFactory calibration certificate (at +37 °C)Fully insulated stainless steel door with a 2-point locking system (compression door lock) and an internal glass door, single-leaf1 stainless steel grid shelf, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on returning old appliances can be found on our Environment and Disposal page.Individual requirements and procurement serviceFor the IF30, options available ex-works include additional temperature monitoring, interior lighting and a power socket, as well as a version with the door hinged on the left. Accessories available include additional shelves and grids, a wall bracket and a USB-to-Ethernet adapter. We arrange calibration, IQ/OQ/PQ and maintenance services for qualification and maintenance. We are happy to advise you personally on individual requirements or any queries regarding the appropriate equipment.

With an internal volume of 32 litres, a temperature range of 20 to 80 °C and purely natural convection, the Memmert IN30 incubator is designed as a compact incubator for the incubation and cultivation of samples in microbiology, food analysis and the pharmaceutical industry. An internal glass door allows visual inspection of the cultures without having to open the fully insulated outer door and thereby disturb the internal temperature, a practical difference compared to the pure heating and drying ovens of the UN series.Natural convection for stable incubation conditionsThe Memmert IN30 incubator operates without an air turbine or a forced-air fan; the heat rises within the chamber purely by thermal convection. This is an advantage for the cultivation of microorganisms and cell cultures: there is no forced air movement that could dry out open Petri dishes or affect culture media. The operating temperature range starts at a minimum of 5 °C above room temperature and extends up to 80 °C. A DIN Class A Pt100 temperature sensor with 4-wire measurement ensures a setting accuracy of 0.1 °C across the entire operating range, important for reproducible incubation temperatures, such as 37 °C in microbiology.ControlCOCKPIT SingleDISPLAY and data acquisitionThe IN30 is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphic display. The temperature can be set in Celsius or Fahrenheit, as well as the position of the exhaust air flap, programme duration, time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWAIT function only starts the incubation time once the setpoint temperature has actually been reached, which is important for defined incubation times. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download.Capacity and dimensions of the Memmert IN30 incubatorThe internal chamber measures 400 x 320 x 250 mm, whilst the external dimensions are 585 x 704 x 434 mm. An electropolished stainless steel grid shelf is included in the scope of delivery; the incubator can accommodate up to three shelves in total. The maximum load capacity is 60 kg for the entire unit and 20 kg per shelf, which is more than sufficient for Petri dishes, test tubes and smaller culture vessels. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The IN30 is connected to 230 V (approx. 1,600 W) or 115 V (approx. 800 W), in both cases at 50/60 Hz, with noticeably lower power consumption than the heating ovens of the UN series with their higher temperature range.Selection guide: choosing the right incubator sizeMemmert offers two sizes with natural convection, as well as the forced-air version with TwinDISPLAY for different temperature distribution requirements.ModelInternal volume and controlIN3032 l, natural convection, SingleDISPLAY, max. 3 shelvesIN5553 l, natural convection, SingleDISPLAY, max. 4 shelvesIF30plus32 l, forced air circulation, TwinDISPLAY, max. 3 shelvesFor those who wish to incubate more culture vessels simultaneously whilst still avoiding forced air circulation, the Memmert IN55 incubator with a 53-litre capacity offers the next level. Those who, on the other hand, require active, more uniform air circulation as well as an integrated sterilisation programme will find these functions in the Memmert IF30plus incubator, which is identical in size. The full range of climate chambers and incubators can be found under Climate Chambers & Incubators.Distinction: Incubator versus heating oven, IN versus IFUnlike the universal ovens in the UN series, the IN30 is specifically designed for incubation temperatures up to 80 °C, not for drying or tempering processes up to 300 °C. The inner glass door, included with the IN30, is not part of the standard specification for the UN models and is important for culture monitoring without temperature loss. Within the incubator range, the key purchasing decision is between natural convection (IN series) and forced air circulation (IF series): The IF30plus features an air turbine, two Pt100 sensors for mutual monitoring, a TwinDISPLAY with two screens and a permanently installed sterilisation programme for the interior, all functions that the IN30, with its SingleDISPLAY, does not offer. Those who switch between different sample types and wish to decontaminate the interior between runs are better served by the IF30plus; those who require quiet, vibration-free incubation without air movement are better off sticking with the IN30.Safety according to DIN 12880The IN30 features adjustable electronic temperature monitoring and a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature reaches approximately 20 °C above the maximum chamber temperature, important for incubation runs lasting several days without constant supervision. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. The unit bears CE and EAC markings as well as a UL mark.Installation, operation and disposalFor operation, a minimum distance of 15 cm from the wall and a minimum distance of 20 cm from the ceiling must be maintained; a minimum of 5 cm is sufficient on either side in relation to a wall or neighbouring unit. Installation is permitted at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the IN30 is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The interior and the inner glass door can be cleaned using standard laboratory cleaning agents and disinfectants. As an electrical appliance, the IN30 is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste.Typical areas of applicationWith an internal volume of 32 litres and incubation temperatures of up to 80 °C, the Memmert IN30 incubator is suitable for compact routine applications in microbiology and food technology.Incubation of culture media and cultures in routine microbiological workBacterial count determination and shelf-life testing in food analysisIncubation of small batches in the pharmaceutical industry and researchVisual inspection of ongoing cultures without temperature loss thanks to the internal glass doorCompact entry-level incubator for schools, training and routine laboratoriesReasons for investment: Equipment for day-to-day incubationThe IN30 comes supplied with 1 electropolished stainless steel grid shelf and the internal glass door; the incubator is designed to accommodate up to 3 shelves. For process documentation, we recommend a permanent AtmoCONTROL software licence rather than the time-limited trial version, supplemented by a USB-to-Ethernet adapter. Those wishing to secure access can configure a lockable door with a security lock; for enhanced safety, an additional Pt100 sensor with overtemperature protection is available. For pharmaceutical or standards-compliant applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Those wishing to combine the IN30 with other devices on a shelf or rack will find a space-saving solution in a wall bracket or stacking kit, without taking up any additional floor space.Frequently asked questions before purchaseWhat is the inner glass door for?It allows visual inspection of the cultures without having to open the fully insulated outer door, which reduces temperature fluctuations inside the unit and disturbs the incubation process less.Up to what temperature does the IN30 operate?The adjustable temperature range is from 20 to 80 °C; the operating temperature range starts at a minimum of 5 °C above room temperature.How many culture vessels can fit inside at the same time?One grid shelf is included as standard; up to three shelves, each with a maximum load of 20 kg, are possible, for a total load of up to 60 kg.Is the IN30 different from the UN30 universal oven?Yes, the IN30 is designed for incubation temperatures up to 80 °C and has an internal glass door, whilst the UN30 operates as a heating and drying oven up to 300 °C without an internal glass door.Is the IN30 a medical device?No, according to Memmert’s own MDR classification table, the IN30 is not a medical device; this applies only to the separate m and mplus variants.Is there a version with active air circulation?Yes, the Memmert IF30plus incubator, which is the same size, features forced air circulation, TwinDISPLAY and an integrated sterilisation programme.Is the IN30 suitable for continuous operation over several days?The mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at an excess temperature of approximately 20 °C and is designed for unattended operation.Can the IN30 also be used for drying tasks instead of incubation?In principle, yes, provided the setpoint temperature is within the range of 20 to 80 °C. For higher drying temperatures up to 300 °C, a heating and drying oven from the UN series, such as the Memmert UN30 universal oven, is the more suitable choice.Technical detailsAdjustable temperature range20 to 80 °COperating temperature rangeat least 5 °C above room temperature up to 80 °CTemperature setting accuracy0.1 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 48 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 800 WMaximum number of shelves3Shelves included in scope of delivery1Max. load on unit60 kgMax. load per shelf20 kgInterior materialStainless steel, 4-sided all-round heatingCasing materialTextured stainless steel, galvanised sheet steel rear panelControl systemControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayTimer1 minute to 99 days, digital countdown timerPermissible ambient temperature5 °C to 40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation height2,000 mMarkingsCE, EAC, UL marksScope of delivery1x Memmert IN30 incubatorFactory calibration certificate (calibrated at 37 °C)Fully insulated stainless steel door with 2-point locking mechanism (compression door lock)Inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert IN30 incubator is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Individual requirements & procurement serviceOptions available for the IN30 include interior lighting and a power socket, a lockable door with a security lock, an additional Pt100 sensor with over-temperature protection, and reinforced grid shelves. For data acquisition, a USB-to-Ethernet adapter and AtmoCONTROL software licences are available. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories or assistance in selecting the right incubator for your application? Through our procurement service, we will be happy to assist you with procurement and configuration.

The Memmert UN30pa paraffin oven holds 32 litres and, at 585 x 704 x 434 mm, has the most compact external dimensions of the five sizes in the paraffin oven series. The nearly gas-tight interior heats paraffin and other embedding media in the range from +20 to +80 °C, controlled via two redundant Pt100 sensors on the TwinDISPLAY. One stainless steel grid shelf is part of the scope of delivery, and up to three shelves are possible in total.Interior and equipmentThe interior measures 400 x 320 x 250 mm and is stiffened by deep-drawn ribbing, and the 4-sided all-round heating is protected and integrated behind it. The fully insulated stainless steel door closes via 2-point locking as a compression door lock, and the housing has a fully galvanised sheet steel rear wall. A total load of up to 60 kg is permitted with a maximum of 20 kg per shelf.Control and temperature monitoringTwo DIN class A Pt100 sensors in 4-wire measurement monitor each other and take over the function of the other in the event of a fault, and display and control are via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays. The setting accuracy is 0.1 °C, and the SetpointWAIT function starts the process time only when the setpoint temperature has actually been reached. A mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at about 20 °C above the maximum oven temperature, and an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can optionally be switched on in addition. AutoSAFETY runs in parallel with its own alarm when the setpoint is exceeded or undershot, and a self-diagnosis system supports fault finding.Guide to choosing within the paraffin oven seriesIf three shelves are not enough for the sample quantity, the UN55pa with 53 litres and up to four shelves has more capacity and additionally the HeatBALANCE function, see the size table below. The UN30pa remains suitable when little floor space is available and individual samples or small series are embedded.Difference from the UN30 universal ovenWith the same internal volume of 32 litres, the universal oven UN30 goes up to +300 °C and is controlled via a SingleDISPLAY. The UN30pa stays at a maximum of +80 °C, but with two Pt100 sensors on the TwinDISPLAY and a nearly gas-tight interior for paraffin and other embedding media.Typical applicationsWith 32 litres of internal volume, the UN30pa is suitable for sample preparation in pathology and histology as well as for producing microscopic specimens in teaching and research.Embedding and heating paraffin or other embedding media for histologySample preparation in pathologyProduction of microscopic specimens in the laboratory, in teaching and researchTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 5 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mm (plus 56 mm for door handle)Net weightapprox. 45 kgConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 800 W (factory option X2 for 115 V)Shelves max.3Shelves included in scope of delivery1Max. load of unit60 kgMax. load per shelf20 kgInteriornearly gas-tight, deep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsSetpointWAIT, AutoSAFETY, visual and audible alarmPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMax. installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe UN-pa paraffin oven series comprises five sizes from 32 to 161 litres, listed below sorted by internal volume:ModelInternal volumeSetting temperatureDisplayUN30pa (this page)32 l+20 to +80 °CTwinDISPLAYUN55pa53 l+20 to +80 °CTwinDISPLAYUN75pa74 l+20 to +80 °CTwinDISPLAYUN110pa108 l+20 to +80 °CTwinDISPLAYUN160pa161 l+20 to +80 °CTwinDISPLAYScope of delivery1x Memmert paraffin oven UN30paFactory calibration certificate (calibration at +80 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.Individual requirements and procurement serviceFor the UN30pa, a full-view glass door, door-open detection and a programmable door lock, among other things, can be ordered from the factory. Additional shelves and perforated trays, drip trays, a wall bracket, a USB Ethernet adapter and a stacking kit are available as accessories. For qualification and maintenance, we arrange calibration, IQ/OQ and maintenance services. For individual requirements, we will advise you personally.

The Memmert IPP30 Peltier-cooled incubator reliably maintains samples and cultures at temperatures ranging from 0 to +70 °C, including well below room temperature, which is not possible with conventional heated incubators. With an internal capacity of 32 litres, the unit is suitable for smaller sample quantities in day-to-day laboratory and research work, such as culture preparations requiring refrigerated storage or temperature-sensitive reagents. Peltier technology for precise cooling and heating Instead of a conventional compressor, the IPP30 utilises the Peltier principle: a Peltier element integrated into the rear wall can both cool and heat, thereby controlling the entire temperature range from 0 to +70 °C with a setting accuracy of 0.1 °C. A Pt100 sensor of DIN Class A quality (4-wire measurement) measures the temperature, whilst the electronically controlled forced internal air circulation ensures even distribution throughout the interior. SingleDISPLAY: all values at a glance The ControlCOCKPIT SingleDISPLAY shows the actual and setpoint temperatures on a high-resolution TFT colour graphic display. Log data from the integrated data logger can be read out and managed via the Ethernet interface (a time-limited trial version of the AtmoCONTROL software is available for download). For full programming, including a USB port and AtmoCONTROL software included as standard, the TwinDISPLAY variant IPP30plus is available. As only one sensor monitors the temperature, the SingleDISPLAY model is particularly suitable for routine applications where there is no need for redundant sensors or full process documentation via AtmoCONTROL. However, for those requiring two independent Pt100 sensors, automatic over/under-temperature protection (AutoSAFETY) and full programmability via Ethernet or USB, the IPP30plus offers these features, whilst retaining the same internal dimensions, temperature range and external dimensions. Safety and workmanship For added safety, the unit monitors the temperature electronically and additionally via a mechanical temperature limiter. The fully insulated stainless steel door with a 2-point compression lock and the inner glass door allow visual inspection of the interior without disrupting the temperature through frequent opening. The stainless steel interior accommodates up to 3 shelves with a maximum total load of 60 kg (20 kg per shelf); an electropolished stainless steel grid shelf is included as standard. Compact size within the IPP series With an internal volume of 32 litres, the IPP30 is the smallest model in Memmert’s range of Peltier-cooled incubators, which also includes the IPP55 (53 litres) and IPP110eco (108 litres) models, each of which is also available in a SingleDISPLAY and a TwinDISPLAY version. Those who regularly cool larger quantities of samples or require more shelves will find suitable alternatives featuring the same Peltier technology and the same temperature range of 0 to +70 °C. The compact external dimensions of 585 × 704 × 434 mm (width × height × depth, plus door handle and Peltier rear panel) make the IPP30 easy to integrate into even laboratories with limited floor space. Operating conditions and installation The IPP30 is designed for operation at ambient temperatures between +16 and +40 °C and a relative humidity of up to 70 % (non-condensing), at altitudes of up to 2,000 metres above sea level. It can be connected to either 230 V or 115 V (50/60 Hz) with a power consumption of around 140 W. The net weight is around 40 kg. Typical applications As a Peltier-cooled incubator with a temperature range of 0 to +70 °C, the IPP30 is suitable for applications that conventional heated incubators cannot accommodate: Storage/incubation of temperature-sensitive samples and cultures below room temperatureMicrobiological cold incubation, e.g. for psychrophilic/cold-loving organismsTemperature-stable storage of reagents and reference materials in the laboratoryQuality assurance and research requiring reproducible temperatures above and below room temperature Particularly in smaller laboratories with limited space, the IPP30 can replace two separate units: a conventional incubator for temperatures above room temperature and an additional cooling unit for lower temperatures. As the Peltier element can both heat and cool, a single unit covers both applications, an advantage that directly translates into savings in floor space and procurement costs. Technical details Internal volume32 litres Internal dimensions (W×H×D)400 × 320 × 250 mm (depth minus 10 mm for the fan) External dimensions (W×H×D)585 × 704 × 434 mm (+56 mm door handle, +111 mm Peltier rear panel) Setting temperature range0 to +70 °C Working temperature range (without lighting)at least 20 °C below room temperature to +70 °C Setting accuracy0.1 °C Sensors1× Pt100 DIN Class A, 4-wire measurement Cooling/heating principlePeltier element, integrated into the rear panel VentilationForced circulation of internal air via Peltier forced air circulation fan ControlControlCOCKPIT SingleDISPLAY, TFT colour graphic display Temperature monitoringElectronic + mechanical temperature limiter DoorFully insulated stainless steel door with 2-point locking mechanism, inner glass door Max. load60 kg in total / 20 kg per shelf Max. number of shelves3 InterfacesEthernet (data logger readout) Voltage/Power230 V or 115 V, 50/60 Hz, approx. 140 W Environmental conditions+16 to +40 °C, max. 70 % RH (non-condensing), max. 2,000 m above sea level Packaging dimensions660 × 890 × 650 mm Net weight/Gross weightapprox. 40 kg / approx. 56 kg Scope of delivery 1× Memmert IPP30 Peltier-cooled incubator (basic unit) 1× stainless steel grid shelf, electropolished 1× factory calibration certificate (calibration at +10/+25/+40 °C) Regulatory information Manufacturer’s WEEE registration number (Memmert GmbH + Co. KG, Stiftung EAR): DE 66812464. Individual requirements & procurement service Do you require additional accessories such as further stainless steel grid shelves, a door lock, a bespoke calibration or advice on the appropriate model size? Our procurement service will be happy to assist you with special enquiries and spare parts. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert IPP30plus Peltier-cooled incubator reliably maintains samples and cultures at temperatures ranging from 0 to +70 °C, including well below room temperature. With an internal capacity of 32 l and the TwinDISPLAY feature, the unit is suitable for applications with higher demands on redundancy, documentation and process reliability compared to the SingleDISPLAY basic version, the IPP30. TwinDISPLAY: dual sensor system, full programmability Instead of a single Pt100 sensor, the IPP30plus features two Pt100 sensors of DIN Class A quality (4-wire measurement) that monitor the temperature in tandem. If one sensor fails, the second automatically takes over. In addition, the upper and lower Peltier elements can be controlled individually, allowing for a more precise distribution of cooling and heating power within the chamber. Via the Ethernet OR USB port, you can programme, manage and transfer process data directly using the AtmoCONTROL software included in the scope of delivery, without the need for a separate licence, unlike with the SingleDISPLAY version. AutoSAFETY: automatic over-/under-temperature protection The AutoSAFETY (ASF) function automatically tracks the setpoint within a selectable tolerance range and, in the event of over- or under-temperature, triggers an alarm or switches off the heating/cooling function, a level of safety not offered by the SingleDISPLAY basic version. In addition, an adjustable temperature monitor/limiter of protection class TWW 3.3 or TWB 2 can be freely selected on the display. Only TwinDISPLAY units can also be ordered with optional extensions such as a programmable door lock (Option D4), door-open detection (Option V5) or a USB user ID stick for access authorisation (Option B33170); according to the manufacturer, these extensions are not technically available on the basic SingleDISPLAY version. Workmanship and features The fully insulated stainless steel door with a 2-point compression lock and the internal glass door allow visual inspection of the interior without disrupting the temperature through frequent opening. The stainless steel interior offers space for up to 3 shelves with a maximum total load of 60 kg (20 kg per shelf); an electropolished stainless steel grid shelf is included as standard. Compact design within the IPP series With an internal volume of 32 l, the IPP30plus is the smallest TwinDISPLAY model in Memmert’s range of Peltier-cooled incubators, which also includes the IPP55plus (53 l) and IPP110ecoplus (108 l), each featuring the same TwinDISPLAY equipment, redundant sensors and AutoSAFETY. Those who regularly cool larger sample volumes or require more shelves will find suitable alternatives featuring the same Peltier technology and the same temperature range of 0 to +70 °C. Operating conditions and installation The IPP30plus is designed for operation at ambient temperatures between +16 and +40 °C and a relative humidity of up to 70 % (non-condensing), at altitudes of up to 2,000 metres above sea level. It can be connected to either 230 V or 115 V (50/60 Hz) with a power consumption of around 140 W. The net weight is around 40 kg. Typical applications As a TwinDISPLAY version with redundant sensors and AutoSAFETY, the IPP30plus is particularly suitable where process reliability and documentation are essential: Validatable refrigerated incubation with documented, redundant temperature monitoringMicrobiological refrigerated incubation with heightened requirements for reliabilityTemperature-stable storage of sensitive reagents and reference materialsResearch and quality assurance requiring full programmability via AtmoCONTROL Particularly in smaller laboratories with limited space, the IPP30plus often replaces two separate units: a conventional heating incubator for temperatures above room temperature and an additional cooling unit for lower temperatures. As the Peltier element can both heat and cool, a single unit covers both applications. In combination with redundant sensor technology and AutoSAFETY, the unit is particularly suitable for applications where a sensor failure must not go unnoticed, such as during unattended incubation runs lasting several days. Technical details Internal volume32 l Internal dimensions (W×H×D)400 × 320 × 250 mm (depth minus 10 mm for the fan) External dimensions (W×H×D)585 × 704 × 434 mm (+56 mm door handle, +111 mm Peltier rear panel) Setting temperature range0 to +70 °C Working temperature range (without lighting)at least 20 °C below room temperature up to +70 °C Setting accuracy0.1 °C Sensors2× Pt100 DIN Class A, 4-wire measurement, cross-monitoring with automatic function takeover Cooling/heating principlePeltier, individual control of upper/lower element VentilationForced circulation of internal air via Peltier forced air circulation fan ControlControlCOCKPIT TwinDISPLAY, 2× TFT colour graphic displays Safety functionAutoSAFETY (automatic over/under-temperature protection), selectable temperature monitor/limiter TWW 3.3 or TWB 2 DoorFully insulated stainless steel door with 2-point locking, internal glass door Max. load60 kg total / 20 kg per shelf Max. number of shelves3 InterfacesEthernet + USB, full programming/management via AtmoCONTROL software (included in the scope of delivery) Voltage/Power230 V or 115 V, 50/60 Hz, approx. 140 W Environmental conditions+16 to +40 °C, max. 70 % RH non-condensing, max. 2,000 m above sea level Packaging dimensions660 × 890 × 650 mm Net weight/Gross weightapprox. 40 kg / approx. 56 kg Scope of delivery 1× Memmert IPP30plus Peltier-cooled incubator (basic unit) 1× stainless steel grid shelf, electropolished AtmoCONTROL software (USB stick) 1× factory calibration certificate (calibration at +10/+25/+40 °C) Regulatory information Manufacturer’s WEEE registration number (Memmert GmbH + Co. KG, Stiftung EAR): DE 66812464. Individual requirements and procurement service Do you require additional accessories such as further stainless steel grid shelves, a programmable door lock, a door-open detection system or a bespoke calibration? Our procurement service will be happy to assist you with special enquiries and spare parts. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert incubator IN30m is a class I medical device according to Regulation (EU) 2017/745. Its intended purpose is the warming and keeping warm of fango, silicate and APS packs in physiotherapy. With 32 litres of internal volume, it is the smallest model in the IN-m series, and the internal dimensions are 400 x 320 x 250 mm. One electropolished stainless steel grid shelf is supplied as standard, and up to three shelves are possible.SingleDISPLAY and temperature controlThe IN30m is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphic display. A Pt100 sensor of DIN class A measures in 4-wire measurement, and the setting accuracy is 0.1 °C. The working temperature range starts at least 5 °C above room temperature and extends to +80 °C. The SetpointWAIT function starts the process time only when the set temperature has been reached, and the digital countdown timer can be set from 1 minute to 99 days. Three freely selectable temperature values can be calibrated.Ventilation, safety and diagnosticsNatural ventilation supplies preheated fresh air via an electronically adjustable exhaust air flap, and the exhaust air outlet has an electronically controllable throttle valve. A mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum chamber temperature, and an electronic temperature monitor can also be set. A self-diagnosis system helps with fault finding. The data logger can be read out, managed and organised via Ethernet, and a time-limited trial version of the AtmoCONTROL software is available for download for this purpose. A USB stick with the software is available as an accessory.Construction, loading and connectionThe interior is made of easy-care stainless steel, stiffened by deep-drawn ribbing and equipped with a protected, integrated 4-sided all-round heating system. One electropolished stainless steel grid shelf is supplied as standard, a maximum of three shelves is possible, and a total load of 60 kg at 20 kg per shelf is permitted. The fully insulated stainless steel door has 2-point locking with a compression door lock and an inner glass door. The IN30m is connected at 230 V at approx. 1,600 W or at 115 V at approx. 800 W, in each case 50/60 Hz. The external dimensions are 585 x 704 x 434 mm plus 56 mm door handle, the net weight is around 48 kg, and the gross weight in the carton is around 64 kg.Distinction: laboratory unit IN30 and medical device IN30mplusIn the same size, there is the Memmert incubator IN30 without a medical intended purpose. Also with 32 litres, there is the IN30mplus with ControlCOCKPIT TwinDISPLAY instead of SingleDISPLAY. Its intended purpose is different: it is used to temper irrigation and infusion solutions and contrast media, not to warm fango, silicate and APS packs.Choosing the right sizeThe IN30m is the smallest model in the IN-m series. Those who need more chamber volume will find the next size up in the IN55m with 53 litres, four shelves and 80 kg total load.Typical applicationsAs a class I medical device, the IN30m is intended exclusively for the physiotherapeutic applications stated in the intended purpose.Warming of fango packs for physiotherapeutic useWarming and keeping warm of silicate packsWarming and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 5 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mm (plus 56 mm door handle)Net weightapprox. 48 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 800 WShelves in the scope of delivery1Maximum number of shelves3Max. load of unit60 kgMax. load per shelf20 kgControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayMedical device classificationClass I according to Regulation (EU) 2017/745Intended purposeWarming/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe IN30m is one of eight sizes in the IN-m series from 32 to 749 litres, all with SingleDISPLAY and the same setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIN30m (this page)32 l+20 to +80 °CSingleDISPLAYIN55m53 l+20 to +80 °CSingleDISPLAYIN75m74 l+20 to +80 °CSingleDISPLAYIN110m108 l+20 to +80 °CSingleDISPLAYIN160m161 l+20 to +80 °CSingleDISPLAYIN260m256 l+20 to +80 °CSingleDISPLAYIN450m449 l+20 to +80 °CSingleDISPLAYIN750m749 l+20 to +80 °CSingleDISPLAYScope of deliveryFactory calibration certificate (calibration at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock), inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The IN30m is also classified as a class I medical device according to Regulation (EU) 2017/745, with the intended purpose of warming and keeping warm fango, silicate and APS packs in physiotherapy.Individual requirements and procurement serviceFor the IN30m, Memmert offers options, accessories and services, and options are specified at the factory when ordering. Accessories include, for example, a USB stick with the AtmoCONTROL software. We will clarify individually, where required, which equipment, spare parts or services are available for the IN30m. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

32 litres interior, 704 mm housing height: the Memmert incubator IN30mplus is the smallest size in the IN-mplus series. As a Class I medical device according to Regulation (EU) 2017/745, it is used to temper irrigation and infusion solutions and contrast media. One electropolished stainless steel grid shelf is supplied as standard, and up to three shelves are possible.Display and sensorsThe ControlCOCKPIT TwinDISPLAY, an adaptive digital PID microprocessor controller with two TFT colour graphic displays, handles the control. Two Pt100 sensors of DIN class A measure in 4-wire technology and check each other: if one sensor fails, the second takes over automatically. The set temperature can be adjusted between +20 and +80 °C, and the setting accuracy is 0.1 °C. The working temperature range starts at least 5 °C above room temperature.SafetyA mechanical temperature limiter of protection class 1 (DIN 12880) disconnects the heating from the mains at about 20 °C above the maximum chamber temperature. Optionally, an adjustable temperature monitor (protection class 3.1) or an adjustable temperature limiter (protection class 2) can be activated on the display. The AutoSAFETY function follows the set point at a freely selectable offset, warns visually and audibly in case of deviations and switches off the heating if the set point is exceeded; a self-diagnosis system helps with fault finding. A program of 4 hours at 160 °C is permanently stored for sterilising the interior, not for sterilising load items.Functions and connectivityHeatBALANCE: heating power distribution of upper/lower heating group adjustable from -50 to +50 %SetpointWAIT: process time starts only after the set temperature has been reachedCalibration function for three freely selectable temperature valuesEthernet interface and USB port for programs with the AtmoCONTROL softwareProgram sequence saved in the event of a power failureInterior, ventilation and connectionThe stainless steel interior is easy to clean, stiffened by deep-drawn ribbing and heated on all four sides. The housing is made of textured stainless steel with a fully galvanised rear wall. With natural ventilation, preheated fresh air flows in, and the exhaust air volume is controlled by an electronically adjustable throttle valve on the exhaust air outlet. The internal dimensions are 400 x 320 x 250 mm and the external dimensions 585 x 704 x 434 mm (plus 56 mm door handle), and the net weight is around 48 kg. A total load of 60 kg is permitted at a maximum of 20 kg per shelf. The mains connection is 230 V (approx. 1,600 W), and in the 115 V version approx. 800 W, in each case 50/60 Hz.The IN30m in comparisonSame size, but with a different intended purpose: the IN30m is likewise a Class I medical device, but is used for warming and keeping warm fango, silicate and APS packs in physiotherapy. It has only one SingleDISPLAY and a single Pt100 sensor, without the second display and the redundant sensor pairing of the IN30mplus.Choosing the right sizeIf more capacity is needed, the next size up follows, the Memmert incubator IN55mplus with 53 litres, up to four shelves and 80 kg permissible total load. With 32 litres and a maximum of three shelves, the IN30mplus remains the most compact model in the series.Typical applicationsAs a Class I medical device, the IN30mplus is intended for warming irrigation and infusion solutions and contrast media.Warming irrigation solutionsWarming infusion solutionsWarming contrast mediaTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 5 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mm (plus 56 mm door handle)Net weightapprox. 48 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 800 WShelves in the scope of delivery1Maximum number of shelves3Max. load of unit60 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, SetpointWAIT, AutoSAFETY, visual and audible alarmMedical device classificationClass I according to Regulation (EU) 2017/745Intended purposeWarming irrigation and infusion solutions and contrast mediaPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rh, non-condensingShipping carton (W x H x D)660 x 890 x 650 mmMarkingsCE, VDE, ULOther sizes in the seriesThe IN30mplus is one of eight sizes in the IN-mplus series from 32 to 749 litres, all with TwinDISPLAY and the same setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIN30mplus (this page)32 l+20 to +80 °CTwinDISPLAYIN55mplus53 l+20 to +80 °CTwinDISPLAYIN75mplus74 l+20 to +80 °CTwinDISPLAYIN110mplus108 l+20 to +80 °CTwinDISPLAYIN160mplus161 l+20 to +80 °CTwinDISPLAYIN260mplus256 l+20 to +80 °CTwinDISPLAYIN450mplus449 l+20 to +80 °CTwinDISPLAYIN750mplus749 l+20 to +80 °CTwinDISPLAYScope of deliveryFactory calibration certificate (calibration at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock), inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The IN30mplus is also classified as a Class I medical device according to Regulation (EU) 2017/745, with the intended purpose of warming irrigation and infusion solutions and contrast media.Individual requirements and procurement serviceFor the IN30mplus, Memmert offers options, accessories and services, and options are specified at the factory when ordering. We clarify your individual requirements, from the suitable option to additional accessories, and organise the procurement. Get in touch for non-binding advice. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

With 32 litres, the Memmert incubator IF30m is the smallest chamber in the IF-m series. Like all models in this series, it is a class I medical device according to Regulation (EU) 2017/745, and its intended purpose is the warming and keeping warm of fango, silicate and APS packs in physiotherapy. The internal dimensions are 400 x 320 x 250 mm, and 39 mm of the depth is taken up by the fan. When installed, the cabinet needs at least 15 cm clearance to the wall behind the unit, 20 cm to the ceiling and 5 cm to the side.Benchtop unit with stainless steel chamberInside, the IF30m is made of easy-care, deep-drawn ribbed stainless steel, and the heating is protected, integrated and runs all round on all four sides. One grid shelf made of electropolished stainless steel is part of the scope of delivery, and up to three fit in altogether. Each shelf may carry 20 kg, and a total load of 60 kg is permitted. The fully insulated stainless steel door closes with 2-point locking (compression door lock), and behind it is an inner glass door. Externally, the housing measures 585 x 704 x 434 mm with a net weight of around 48 kg.Operation via ControlCOCKPIT SingleDISPLAYThe ControlCOCKPIT SingleDISPLAY is an adaptive PID microprocessor controller with a TFT colour graphic display. The temperature is measured by a Pt100 sensor of DIN class A in 4-wire measurement, and the setting accuracy is 0.1 °C. In addition to the set temperature, the speed of the forced air circulation motor, the exhaust air flap position, the program run time and the time zone including summer/winter time can be set. A digital countdown timer with target time display covers 1 minute to 99 days, and with SetpointWAIT the process time begins only when the chamber has actually reached the set temperature. Three freely selectable points can be calibrated. An Ethernet interface is available for evaluating the data logger, and the AtmoCONTROL software for this purpose is available for download as a time-limited trial version.SafetyA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum cabinet temperature. An adjustable electronic temperature monitor runs in parallel, and a self-diagnosis system is used for fault finding.Distinction from IN-m and IF-mplusAnyone looking for the same application without forced air circulation will find it in the naturally convected counterpart IN30m, likewise 32 litres and with the same intended purpose. The case is different with the IF30mplus: it shares the chamber size with the IF30m, but is intended for warming irrigation and infusion solutions and contrast media and works with a ControlCOCKPIT TwinDISPLAY, that is, two displays instead of one.Choosing the right sizeThe IF30m is the smallest size in the series, and a move down in size is not possible. If more than three shelves are needed or the planned load exceeds 60 kg, the IF55m with 53 litres, up to four shelves and 80 kg permissible total load is the next step.Typical applicationsAs a class I medical device, the Memmert incubator IF30m is intended exclusively for physiotherapeutic applications with fango, silicate and APS packs.Warming of fango packs for physiotherapeutic useWarming and keeping warm of silicate packsWarming and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangeAt least 10 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mmShelves in the scope of delivery1Maximum number of shelves3Max. load of unit60 kgMax. load per shelf20 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 800 WNet weightapprox. 48 kgMedical device classificationClass I according to Regulation (EU) 2017/745Intended purposeWarming and keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, cULus ListedOther sizes in the seriesThe IF30m is one of eight sizes in the IF-m series from 32 to 749 litres, all with SingleDISPLAY and the same setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIF30m (this page)32 l+20 to +80 °CSingleDISPLAYIF55m53 l+20 to +80 °CSingleDISPLAYIF75m74 l+20 to +80 °CSingleDISPLAYIF110m108 l+20 to +80 °CSingleDISPLAYIF160m161 l+20 to +80 °CSingleDISPLAYIF260m256 l+20 to +80 °CSingleDISPLAYIF450m449 l+20 to +80 °CSingleDISPLAYIF750m749 l+20 to +80 °CSingleDISPLAYScope of delivery1x Memmert incubator IF30mFactory calibration certificate (calibration at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The IF30m is also classified as a class I medical device according to Regulation (EU) 2017/745, with the intended purpose of warming and keeping warm fango, silicate and APS packs in physiotherapy.Individual requirements and procurement serviceFor the IF30m, the 115 V voltage variant, extended excess temperature protection and temperature throttling to fixed values between +50 °C and +75 °C, among others, can be selected as factory options when ordering. Accessories include additional grid shelves, perforated trays, drip trays and a wall bracket for wall mounting, as well as USB-Ethernet adapters and the licence for the AtmoCONTROL documentation software. For DAkkS calibration, IQ/OQ/PQ documentation and qualification or a maintenance contract, we will gladly arrange the right contact. Get in touch for individual advice.

The Memmert incubator IF30mplus is a class I medical device according to Regulation (EU) 2017/745 and is used for warming irrigation and infusion solutions and contrast media. With 32 litres of internal volume, it is the smallest size in the IF-mplus series. One stainless steel grid shelf is supplied as standard, and up to three shelves are possible.ControlCOCKPIT TwinDISPLAY and sensorsTwo Pt100 sensors of DIN class A monitor each other in 4-wire measurement and automatically take over the function of the other in case of failure. The setting accuracy is 0.1 °C, the setting temperature range extends from +20 to +80 °C, and the working temperature range starts at least 10 °C above room temperature. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays. The digital countdown timer with target time display can be set from 1 minute to 99 days, and the SetpointWAIT function starts the process time only after the set temperature has been reached. Three freely selectable temperature values can be calibrated.Safety and interiorA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum cabinet temperature. An adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can also be selected on the display. The AutoSAFETY function automatically follows the set point at a freely selectable offset, triggers a visual and audible alarm in case of deviation and switches off the heating if the set point is exceeded. A self-diagnosis system assists with fault finding. A fully insulated stainless steel door with 2-point locking (compression door lock) and an inner glass door close the chamber, and the stainless steel interior is stiffened by deep-drawn ribbing and heated all round. The permanently installed sterilisation program (4 h at 160 °C) is used for sterilising the interior and is not intended for sterilising load items.Ventilation, connection and dimensionsThe electronically controllable air turbine runs quietly and can be set in 10 % steps. Preheated fresh air is admitted via the electronically adjustable exhaust air flap, and the exhaust air outlet has an electronically controllable throttle valve. The IF30mplus is connected at 230 V at approx. 1,600 W or at 115 V at approx. 800 W, in each case 50/60 Hz. The internal dimensions are 400 x 320 x 250 mm and the external dimensions 585 x 704 x 434 mm with a net weight of around 48 kg. A total load of 60 kg at 20 kg per shelf is permitted.Distinction from the SingleDISPLAY and the laboratory unitAs a class I medical device with SingleDISPLAY and only one Pt100 sensor, there is the IF30m, which has a different intended purpose: warming and keeping warm of fango, silicate and APS packs in physiotherapy. The IF30mplus, by contrast, has the TwinDISPLAY with the two mutually monitoring sensors and the adjustable temperature monitor or limiter that can be selected on the display. Without a medical intended purpose, but with TwinDISPLAY and the same chamber size, there is also the laboratory incubator IF30plus.Selection guide: suitable chamber sizeThe IF30mplus is the smallest size in the mplus series, and Memmert does not offer a smaller chamber in this line. Those who need more volume or more shelves will find the next size up in the IF55mplus with 53 litres and up to four shelves.Typical applicationsAs a class I medical device, the IF30mplus is intended for the following applications:Warming irrigation solutionsWarming infusion solutionsWarming contrast mediaTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 10 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 48 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 800 WShelves in the scope of delivery1Maximum number of shelves3Max. load of unit60 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsAutoSAFETY, SetpointWAIT, visual and audible alarmMedical device classificationClass I according to Regulation (EU) 2017/745Intended purposeWarming irrigation and infusion solutions and contrast mediaPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, cULusOther sizes in the seriesThe IF30mplus is one of eight sizes in the mplus series from 32 to 749 litres, all with TwinDISPLAY and the same setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIF30mplus (this page)32 l+20 to +80 °CTwinDISPLAYIF55mplus53 l+20 to +80 °CTwinDISPLAYIF75mplus74 l+20 to +80 °CTwinDISPLAYIF110mplus108 l+20 to +80 °CTwinDISPLAYIF160mplus161 l+20 to +80 °CTwinDISPLAYIF260mplus256 l+20 to +80 °CTwinDISPLAYIF450mplus449 l+20 to +80 °CTwinDISPLAYIF750mplus749 l+20 to +80 °CTwinDISPLAYScope of delivery1x Memmert incubator IF30mplusFactory calibration certificate at +37 °CFully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door1x stainless steel grid shelf, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The IF30mplus is also classified as a class I medical device according to Regulation (EU) 2017/745, with the intended purpose of warming irrigation and infusion solutions and contrast media.Individual requirements and procurement serviceFor the IF30mplus, the 115 V voltage variant is available as a factory option, among others, as is temperature throttling to a range of +50 to +75 °C. For accessories, we arrange additional grid shelves, perforated shelves, shelf and base drip trays, a wall bracket, a stacking kit for units of the same size, a USB-Ethernet adapter or a levelling or mobile base frame. For DAkkS calibration, IQ/OQ/PQ documentation and qualification or a maintenance contract, we will gladly arrange the right contact. Get in touch for individual advice on your equipment.

The Memmert universal oven UN30m is the smallest model in the UN-m series and a Class I medical device under Regulation (EU) 2017/745. The intended purpose is heating and keeping warm fango, silicate and APS packs in physiotherapy. With 32 litres of internal volume and an internal width of 400 mm, the device is supplied as standard with one stainless steel grid shelf, and up to three shelves are possible.Control and sensorsThe UN30m is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphic display. A Pt100 sensor of DIN class A with 4-wire measurement records the temperature, and the setting accuracy is 0.1 °C up to a set temperature of 99.9 °C and 0.5 °C from 100 °C. The setting temperature range extends from +20 to +300 °C. A digital countdown timer with target time indication can be set from 1 minute to 99 days, and the SetpointWAIT function only starts the process time once the set temperature has been reached. Three freely selectable temperature values can be calibrated, and the temperature can be displayed in either Celsius or Fahrenheit.Air circulationThe UN30m ventilates without a forced air circulation fan, and convection is purely natural. An electronically adjustable exhaust air flap mixes in pre-heated fresh air, and the exhaust air port is equipped with an electronically adjustable throttle valve.SafetyAn adjustable electronic temperature monitor works together with a mechanical temperature limiter TB of protection class 1 according to DIN 12880, which switches the heating off at approx. 20 °C above the maximum cabinet temperature. A self-diagnosis system assists with fault finding. The interior made of easy-care stainless steel is stiffened by deep-drawn ribbing and equipped with protected, integrated 4-sided all-round heating, and the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel.Loading, connection and dimensionsA total load of 60 kg is permitted at 20 kg per shelf, and one electropolished stainless steel grid shelf is included as standard. The connection is 230 V with approx. 1,600 W or 115 V with approx. 1,600 W, in each case 50/60 Hz. The internal dimensions are 400 x 320 x 250 mm and the external dimensions 585 x 704 x 434 mm, with a net weight of approx. 45 kg. The data logger can be read out, managed and organised via an Ethernet interface, and a USB stick with AtmoCONTROL software is available as an accessory if required.Difference from the laboratory ovenFor applications without a medical intended purpose, such as drying and annealing in laboratories and industry, we offer the Memmert universal oven UN30 in the same chamber size. Within the medical device line, the UN30mplus is also available as a version with two displays for control.Selection guideThe UN30m is the smallest size in the UN-m series. Anyone who needs more volume or more shelves will find the next larger version in the UN55m with 53 litres, four shelves and 80 kg total load.Typical applicationsHeating of fango packs for physiotherapeutic useHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 5 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mm (D +56 mm door handle)Net weightapprox. 45 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 1,600 WShelves in scope of delivery1Shelves, maximum3Max. load, unit60 kgMax. load per shelf20 kgControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller with TFT colour graphic displayMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe UN-m series comprises eight sizes, from 32 to 749 litres, each with SingleDISPLAY and the setting temperature range +20 to +300 °C.ModelInternal volumeSetting temperatureDisplayUN30m (this page)32 l+20 to +300 °CSingleDISPLAYUN55m53 l+20 to +300 °CSingleDISPLAYUN75m74 l+20 to +300 °CSingleDISPLAYUN110m108 l+20 to +300 °CSingleDISPLAYUN160m161 l+20 to +300 °CSingleDISPLAYUN260m256 l+20 to +300 °CSingleDISPLAYUN450m449 l+20 to +300 °CSingleDISPLAYUN750m749 l+20 to +300 °CSingleDISPLAYScope of delivery1x Memmert universal oven UN30mFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on the return of old appliances can be found on our page Environment and disposal. The UN30m is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Individual requirements and procurement serviceFor the UN30m, Memmert lists options, accessories and services, such as additional grid shelves or a different voltage variant. If you need accessories, calibration or maintenance, contact us for individual advice. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert universal oven UN30mplus is a Class I medical device under Regulation (EU) 2017/745 with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy. With 32 litres of internal volume, it is the smallest model in the UN-mplus series, one stainless steel grid shelf is included as standard, and up to three shelves are possible.Sensors and displayTwo Pt100 sensors of DIN class A back each other up using 4-wire measurement, and in the event of a fault the other sensor automatically takes over the function. Display and control are via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays, and up to 99.9 °C the setting accuracy is 0.1 °C, above that 0.5 °C. The digital countdown timer covers a range from 1 minute to 99 days, and SetpointWAIT only starts the process time once the set temperature has been reached. Programs can be programmed, managed and transferred via the Ethernet interface or USB port using the AtmoCONTROL software.Safety in everyday useTwo temperature monitors are permanently installed: the mechanical limiter of protection class 1 according to DIN 12880, which disconnects the heating at approx. 20 °C above the maximum cabinet temperature, and optionally an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2, both adjustable on the display. In addition, AutoSAFETY signals visually and audibly as soon as the temperature leaves the selected range around the set value, and a self-diagnosis system helps with troubleshooting.Loading, connection and dimensionsA total load of 60 kg is permitted at 20 kg per shelf. The UN30mplus is connected at 230 V with approx. 1,600 W or at 115 V, also with approx. 1,600 W, in each case 50/60 Hz. The internal dimensions are 400 x 320 x 250 mm and the external dimensions 585 x 704 x 434 mm (plus 56 mm for the door handle), with a net weight of approx. 45 kg.Distinction from the laboratory oven and the SingleDISPLAY versionThe laboratory unit of the same size without a medical intended purpose is the Memmert universal oven UN30plus also with 32 litres and TwinDISPLAY. In the same size and with the same intended purpose, the UN30m is also available as a Class I medical device in the SingleDISPLAY version with one Pt100 sensor. The UN30mplus, by contrast, has the TwinDISPLAY and two Pt100 sensors that monitor each other, plus the adjustable temperature monitor or adjustable temperature limiter selectable on the display, and AutoSAFETY.Selection guide: the right sizeThe UN30mplus is the smallest model in the series, and there is no smaller size. If 32 litres and three shelves are not enough, the next larger Memmert universal oven UN55mplus has 53 litres of internal volume, four shelves and a total load of 80 kg.Typical applicationsAs a Class I medical device, the Memmert universal oven UN30mplus is intended exclusively for heating and keeping warm fango, silicate and APS packs in physiotherapy.Heating of fango packs for physiotherapeutic useHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 5 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, mutual monitoringInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mmExternal dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgGross weight (shipping carton)approx. 61 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 1,600 WShelves in scope of delivery1Shelves, maximum3Max. load, unit60 kgMax. load per shelf20 kgPackaging dimensions (W x H x D)660 x 890 x 650 mmControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsAutoSAFETY, visual and audible alarmMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe UN30mplus is one of eight sizes in the UN-mplus series from 32 to 749 litres, all with TwinDISPLAY, natural convection and the same setting temperature range of +20 to +300 °C. The same size is also available in the SingleDISPLAY version UN30m.ModelInternal volumeSetting temperatureDisplayUN30mplus (this page)32 l+20 to +300 °CTwinDISPLAYUN55mplus53 l+20 to +300 °CTwinDISPLAYUN75mplus74 l+20 to +300 °CTwinDISPLAYUN110mplus108 l+20 to +300 °CTwinDISPLAYUN160mplus161 l+20 to +300 °CTwinDISPLAYUN260mplus256 l+20 to +300 °CTwinDISPLAYUN450mplus449 l+20 to +300 °CTwinDISPLAYUN750mplus749 l+20 to +300 °CTwinDISPLAYScope of delivery1x Memmert universal oven UN30mplusFactory calibration certificate (calibration at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on the return of old appliances can be found on our page Environment and disposal. The device is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Individual requirements and procurement serviceFurther options, accessories and services are available for the UN30mplus. On request, we put together a suitable combination, from additional equipment to calibration and qualification. Get in touch for individual advice on your requirements. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert universal oven UF30m is the smallest model in the UF-m series for physiotherapy: 32 litres of internal volume, one grid shelf as standard and room for up to 3 shelves. As a Class I medical device under Regulation (EU) 2017/745, it is intended exclusively for heating and keeping warm fango, silicate and APS packs, controlled via a ControlCOCKPIT SingleDISPLAY with one Pt100 temperature sensor.Technology: air turbine, ControlCOCKPIT and DIN 12880An air turbine that is electronically adjustable in 10 % steps distributes the heat in the 32 litre interior, supplemented by an electronically adjustable exhaust air flap for pre-heated fresh air. The setting temperature range extends from 20 to 300 °C, with a setting accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C, measured via a Pt100 sensor of DIN class A. The oven is operated via the ControlCOCKPIT SingleDISPLAY: a PID microprocessor controller with a TFT colour graphic display, a digital countdown timer from 1 minute to 99 days and the SetpointWAIT function, which only starts the process time once the set temperature has been reached. For protection against over-temperature, a mechanical temperature limiter of protection class 1 according to DIN 12880 additionally switches the heating off, a self-diagnosis system reports faults, and three temperature values can be calibrated.Selection guide: the right sizeThe housing measures 585 x 704 x 434 mm, with a further 56 mm in depth for the door handle, and the net weight is approx. 45 kg. At the installation site, a distance of at least 15 cm to the wall and at least 5 cm at the sides must be maintained. The shelves each carry up to 20 kg, and the unit up to 60 kg in total. If more volume is needed, the next larger UF55m with 53 litres and up to 4 shelves is the alternative, with the same external width of 585 mm. Anyone who wants two sensors and two displays instead of one Pt100 sensor will find the correspondingly equipped version as the UF30mplus. For use outside the physiotherapeutic intended purpose, such as a heating and drying oven in the laboratory, there is the Memmert universal oven UF30 with the same dimensions and performance data.Typical applicationsAs a Class I medical device, the Memmert universal oven UF30m is intended exclusively for physiotherapeutic applications with fango, silicate and APS packs.Heating of fango packs for physiotherapeutic useHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 10 °C above room temperature to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgGross weight (packed)approx. 61 kgPackaging dimensions (W x H x D)660 x 890 x 650 mmConnection 230 V50/60 Hz, approx. 1,600 WConnection 115 V50/60 Hz, approx. 1,600 WShelves, maximum3Shelves in scope of delivery1Max. load, unit60 kgMax. load per shelf20 kgInterior materialStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rel., non-condensingMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyMarkingsCE, VDE, UL test marksOther sizes in the seriesThe UF-m series comprises nine sizes between 32 and 1,060 litres of internal volume, all with ControlCOCKPIT SingleDISPLAY and an identical intended purpose for physiotherapy.ModelInternal volumeSetting temperatureDisplayUF30m (this page)32 l+20 to +300 °CSingleDISPLAYUF55m53 l+20 to +300 °CSingleDISPLAYUF75m74 l+20 to +300 °CSingleDISPLAYUF110m108 l+20 to +300 °CSingleDISPLAYUF160m161 l+20 to +300 °CSingleDISPLAYUF260m256 l+20 to +300 °CSingleDISPLAYUF450m449 l+20 to +300 °CSingleDISPLAYUF750m749 l+20 to +300 °CSingleDISPLAYUF1060m1,060 l+20 to +300 °CSingleDISPLAYThe UF30m is also available with two displays and additional sensors as the UF30mplus. For use outside the physiotherapeutic intended purpose, we also offer the laboratory version Memmert universal oven UF30.Scope of delivery1x Memmert universal oven UF30mFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on the return of old appliances can be found on our page Environment and disposal. In addition, the Memmert universal oven UF30m is classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Individual requirements and procurement serviceFor the UF30m, additional grid shelves and spare parts are available from us if required. Get in touch for individual coordination with your practice equipment. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert Universal oven UF30mplus is the smallest model in the mplus series and a Class I medical device under Regulation (EU) 2017/745. The intended purpose is narrowly defined: heating and keeping warm fango, silicate and APS packs in physiotherapy, not drying or materials testing in the laboratory. The external dimensions are 585 x 704 x 434 mm, with a further 56 mm in depth for the door handle. The rear panel of the unit needs at least 15 cm of clearance to the wall.Forced air circulation, TwinDISPLAY and temperature accuracyAn electronically adjustable air turbine distributes the heat in the interior and can be set in 10 % steps, while an electronically adjustable exhaust air flap mixes in pre-heated fresh air. Two Pt100 sensors of DIN class A with 4-wire measurement monitor each other: if one sensor fails, the second automatically takes over its function. The setting accuracy is 0.1 °C up to a set temperature of 99.9 °C and 0.5 °C from 100 °C, and the setting temperature range extends from +20 to +300 °C. The UF30mplus is operated via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays, and programs can be managed and transferred via the Ethernet interface or USB with the AtmoCONTROL software. A digital countdown timer can be set from 1 minute to 99 days, and the SetpointWAIT function only starts the process time once the set temperature has actually been reached.Safety according to DIN 12880A mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heating off at approx. 20 °C above the maximum cabinet temperature. In addition, an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can be selected on the display, and there is also the additional AutoSAFETY monitoring, which automatically follows the set value within a freely selectable range and triggers a visual and audible alarm in the event of a deviation. A self-diagnosis system assists with fault finding, and three freely selectable temperature values can be calibrated. The HeatBALANCE function, with which the larger models in the series distribute the heating power between the upper and lower heating group, is not part of the standard equipment of the UF30mplus.Loading, connection and dimensionsOne electropolished stainless steel grid shelf is included as standard, and up to 3 shelves are possible. A maximum total load of 60 kg and 20 kg per shelf is permitted. The UF30mplus is connected at either 230 V or 115 V at 50/60 Hz and approx. 1,600 W power consumption. The net weight is approx. 45 kg, and the internal dimensions are 400 x 320 x 250 mm.Distinction: physiotherapy unit and laboratory oven UF30plusThe laboratory and industrial oven Memmert universal oven UF30plus has the same external dimensions of 585 x 704 x 434 mm and is intended for drying, heating, annealing and testing, but it has no medical intended purpose. In the same size and with the same intended purpose, the UF30m is available as a Class I medical device in the SingleDISPLAY version with one Pt100 sensor. The UF30mplus, by contrast, has the TwinDISPLAY and two Pt100 sensors that monitor each other, plus the adjustable temperature monitor or adjustable temperature limiter selectable on the display, and AutoSAFETY.Selection guide: is the UF30mplus enough?The UF30mplus holds up to three shelves with a combined maximum of 60 kg, and the internal dimensions are 400 x 320 x 250 mm. Anyone who needs more shelves or more interior space will find 53 litres, up to four shelves and 80 kg total load in the Memmert universal oven UF55mplus with the same external width of 585 mm.Typical applicationsAs a Class I medical device, the Memmert Universal oven UF30mplus is intended exclusively for physiotherapeutic applications with fango, silicate and APS packs.Heating of fango packs for physiotherapeutic useHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsAdjustable temperature range+20 to +300 °CWorking temperature rangemin. 10 °C above room temperature to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume32 lInternal dimensions (W x H x D)400 x 320 x 250 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)585 x 704 x 434 mmNet weightapprox. 45 kgConnection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 1,600 WShelves in scope of delivery1Maximum number of shelves3Max. load, unit60 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsAutoSAFETY, visual and audible alarmMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe UF30mplus is one of nine sizes in the mplus series from 32 to 1,060 litres, all with TwinDISPLAY and the same setting temperature range of +20 to +300 °C.ModelInternal volumeSetting temperatureDisplayUF30mplus (this page)32 l+20 to +300 °CTwinDISPLAYUF55mplus53 l+20 to +300 °CTwinDISPLAYUF75mplus74 l+20 to +300 °CTwinDISPLAYUF110mplus108 l+20 to +300 °CTwinDISPLAYUF160mplus161 l+20 to +300 °CTwinDISPLAYUF260mplus256 l+20 to +300 °CTwinDISPLAYUF450mplus449 l+20 to +300 °CTwinDISPLAYUF750mplus749 l+20 to +300 °CTwinDISPLAYUF1060mplus1,060 l+20 to +300 °CTwinDISPLAYScope of delivery1x Memmert Universal oven UF30mplusFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)1x stainless steel grid shelf, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on the return of old appliances can be found on our page Environment and disposal. The UF30mplus is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Individual requirements and procurement serviceAvailable options for the UF30mplus include the 115 V voltage variant, extended excess temperature protection and temperature throttling (factory limit on the maximum adjustable temperature), plus accessories such as additional grid shelves, perforated shelves, drip trays, a wall bracket or a USB-Ethernet adapter. For DAkkS calibration, IQ/OQ/PQ documentation and qualification, a short training session or a maintenance contract, we also arrange a suitable contact for you. For questions about the right configuration for your practice, our procurement service supports you individually.