Skip to main content Skip to search Skip to main navigation

Memmert IN110plus incubator, 108 L, +20 to +80 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert IN110plus incubator, 108 L, +20 to +80 °C, TwinDISPLAY"

The IN110plus has a capacity of 108 litres with a maximum of five shelves, two of which are fitted as standard, and weighs around 76 kilograms net. The smaller IN75plus, with a capacity of 74 litres, offers as many as six shelves, one more than the larger IN110plus. Temperature control is managed via a ControlCOCKPIT TwinDISPLAY with two Pt100 sensors, operating within a range of +20 to +80 °C.

Design and air flow

An electronically adjustable exhaust air flap introduces preheated fresh air, whilst the exhaust air outlet with a throttle valve is electronically controllable. The interior is reinforced by deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system. The IF-plus series of the same size, by contrast, operates with forced air circulation rather than natural convection.

HeatBALANCE and sensor technology

HeatBALANCE adjusts the distribution of heating output between the upper and lower heating groups from -50 to +50 %. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays; two DIN Class A Pt100 sensors in a 4-wire configuration monitor each other reciprocally. The setting accuracy is 0.1 °C. Programmes can be managed and transferred via Ethernet or USB using the AtmoCONTROL software.

Safety and internal sterilisation

A mechanical temperature limiter of protection class 1 according to DIN 12880 serves as a safety measure; it switches off the heating when the temperature reaches approximately 20 °C above the maximum cabinet temperature. An adjustable temperature monitor (protection class 3.1) or an adjustable temperature limiter (protection class 2) can also be selected on the display. AutoSAFETY monitors instances where the temperature exceeds or falls below the setpoint at freely selectable intervals and signals these both visually and acoustically; the sterilisation programme sterilises the interior, not the contents, at 160 °C within 4 hours.

Selection guide for the right size

If the smaller IN75plus, with a capacity of 74 litres, is no longer sufficient, the IN110plus offers an internal volume of 108 litres, albeit with a maximum of five shelves instead of six. If sample volumes increase further, the table below lists the IN160plus with a 161-litre capacity and eight shelves.

Typical applications

The IN110plus serves as an incubator with natural convection and HeatBALANCE for incubating and temperature-controlling samples between +20 and +80 °C, including in research applications.

  • Incubating and temperature-controlling samples with redundant sensor monitoring
  • Sterilising the interior via the permanently installed programme
  • Use in research

Technical details

Setting temperature range+20 to +80 °C
Working temperature rangeAt least 5 °C above room temperature up to +80 °C
Temperature setting accuracy0.1 °C
Temperature sensor2 Pt100 sensors, DIN Class A, in a 4-wire configuration for mutual monitoring and automatic failover in the event of a fault
HeatBALANCE functionAdjustment of the heating power distribution between the upper and lower heating groups from -50 % to +50 %
Adjustable temperature monitor/limiterAdjustable temperature monitor (TWW), protection class 3.1, or adjustable temperature limiter (TWB), protection class 2, selectable via the display
AutoSAFETYadditionally integrated over- and under-temperature monitoring ‘ASF’, automatically tracks the setpoint at a freely selectable interval, alarm if the temperature exceeds or falls below the setpoint, heating shut-off if the setpoint is exceeded
Sterilisation programmePermanently installed sterilisation programme (4 hours/160 °C) for sterilising the interior; not intended for sterilising the load
Internal volume108 l
Internal dimensions (W x H x D)560 x 480 x 400 mm
External dimensions of housing (W x H x D)745 x 864 x 584 mm (depth plus 56 mm for door handle)
Net weightapprox. 76 kg
Connection 230 V50/60 Hz, approx. 1,400 W
Connection 115 V50/60 Hz, approx. 900 W
Maximum number of shelves5
Shelves included in the scope of delivery2
InteriorEasy to clean, reinforced with deep-drawn ribbing, with protected, integrated 4-sided all-round heating
ControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displays
Permissible ambient temperature+5 °C to +40 °C
Permissible relative humiditymax. 80 % non-condensing
Maximum installation heightmax. 2,000 m above sea level
MarkingsCE, VDE GS, UL, EAC

Other sizes in the series

The IN-plus series with TwinDISPLAY ranges from 32 to 749 litres internal volume, sorted by internal volume:

ModelInternal volumeSet temperatureDisplay
IN30plus32 l+20 to +80 °CTwinDISPLAY
IN55plus53 l+20 to +80 °CTwinDISPLAY
IN75plus74 l+20 to +80 °CTwinDISPLAY
IN110plus (this page)108 l+20 to +80 °CTwinDISPLAY
IN160plus161 l+20 to +80 °CTwinDISPLAY
IN260plus256 l+20 to +80 °CTwinDISPLAY
IN450plus449 l+20 to +80 °CTwinDISPLAY
IN750plus749 l+20 to +80 °CTwinDISPLAY

The same capacity is also available with SingleDISPLAY and a Pt100 sensor in the IN series: IN110.

Scope of delivery

  • 1x Memmert IN110plus incubator
  • Factory calibration certificate (calibrated at +37 °C)
  • Fully insulated stainless steel door with 2-point locking (compression door lock)
  • Inner glass door
  • 2x stainless steel grid shelves, electropolished

Regulatory information

This appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and disposal page.

Installation in a wall opening

For fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.

Individual requirements and procurement service

For the IN110plus, the following items, amongst others, can be ordered ex-works: interior lighting, an interior socket, a potential-free contact for fault reporting, and feed-throughs of various diameters. In addition, we offer a USB user ID stick, reinforced grid shelves, levelling feet and a stacking kit. For qualification and requalification, we also arrange calibration and IQ/OQ services. Please do not hesitate to contact us regarding any individual requirements.

Certification marks: GS (VDE)
Volume: 108 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E20165 for sizes 105, 110, 150 and 160
Manufacturer number: E20165

The E20165 stainless steel grid is an electropolished shelf for 43 Memmert models in sizes 105, 110, 150 and 160. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example IF110 or UF110.For sizes 110 and 160, 2 grids are fitted as standard, and the interior holds up to 5 grids (size 110) or 8 grids (size 160). The HCP105 and HCP150 humidity chambers have 2 perforated shelves as standard; the maximum number there is 6 (HCP105) and 10 (HCP150). According to Memmert, the load per shelf is 20 kg, and 15 kg for the HCP105 and HCP150. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Drying laboratory glassware and medium-sized sample series in routine operation, for example in the UF110Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material specimens and material samples, for example in the UF160Environmental tests and environmental simulations in the HCP105 and HCP150 humidity chambersSuitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)IF110bw2520108IF1102520108IN110plus2520108UF1102520108UN110pa2520108UN160pa2820161IF1602820161IN1602820161IF110plus2520108IF160plus2820161IN160plus2820161UF110plus2520108UN1102520108UN110plus2520108UF1602820161UF160plus2820161UN1602820161UN160plus2820161IN1102520108IPP110eco2520108IPP110ecoplus2520108HPP110eco2520108HCP1052 (perforated shelf)615107HCP1502 (perforated shelf)1015156ICH1102520108ICP1102520108IN110m2520108IN110mplus2520108IF110m2520108IF110mplus2520108IN160m2820161IN160mplus2820161IF160m2820161IF160mplus2820161UN110m2520108UN110mplus2520108UF110m2520108UF110mplus2520108UN160m2820161UN160mplus2820161UF160m2820161UF160mplus2820161UF160TS2820161The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert20 kg, 15 kg for the HCP105 and HCP150Scope of delivery1 stainless steel grid, electropolished (E20165)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €98.04
memmert rohrverlaengerung gerade
Memmert straight slip-on pipe extension B29718 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29718

The straight slip-on pipe extension B29718 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The angled version is also available (B29719). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorTempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Drying and tempering of large, heavy components in industrial manufacturing, for example in the UF1060Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 straight slip-on pipe extensionIndividual requirements & procurement serviceFor the angled version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €41.28
memmert rohrverlaengerung gewinkelt
Memmert angled slip-on pipe extension B29719 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29719

The angled slip-on pipe extension B29719 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The straight version is also available (B29718). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Parallel drying of several sample batches in a confined space, for example in the UN75Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material samples in series, for example in the UN260Testing and curing of larger components in quality assurance, for example in the UF750Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 angled slip-on pipe extensionIndividual requirements & procurement serviceFor the straight version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €108.36
Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert reinforced stainless steel grid E29767 for sizes 110 and 160
Manufacturer number: E29767

The reinforced stainless steel grid E29767 is available for Memmert units in the U, Um, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 110 and 160. It is electropolished and, according to Memmert, can bear up to 60 kg; for the standard grids in these sizes it is 20 kg per shelf. The grid is a shelf level in the interior. The size corresponds to the number in the unit name, for example IF110 or UF110.Please note the maximum load per unit, as it limits the total load of all shelves. The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Tempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Material tests in industrial manufacturing, for example in the UF160Suitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmertup to 60 kgScope of delivery1 reinforced stainless steel grid, electropolishedIndividual requirements & procurement serviceFor standard grids, perforated trays and drip trays of the same size, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €257.14
Memmert levelling feet B29768, set of 4, for sizes 30, 55, 75, 110, 160 and 260
Manufacturer number: B29768

The B29768 set of levelling feet contains 4 pieces. With levelling feet, the unit can be aligned horizontally.The set is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco and HPPeco series in sizes 30, 55, 75, 110, 160 and 260. The table of compatible models shows which series is available in which size. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorEmbedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenParallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoSuitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574UN160pa160161IF30plus3032IN30plus3032IF303032IN303032IF160160161IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UN55pa5553UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032IPP260eco260256IPP260ecoPlus260256HPP110eco110108HPP260eco260256IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF160TS160161UF260TS260256Scope of delivery1 set of levelling feet (4 pieces)Individual requirements & procurement serviceFor base frames, further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €46.44
memmert untergestell fahrbar
Memmert mobile base frame B29750, height 560 mm, for sizes 110 and 160
Manufacturer number: B29750

The mobile base frame B29750 is 560 mm high.It is intended for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco and IFbw series in sizes 110 and 160. The levelling version with a height of 500 mm is also available (B29749), as is a flat base frame with a height of 130 mm (B33661). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example IF110 or UF110.Typical applicationsUnits of sizes 110 and 160 are placed on the base frame. Typical uses of these units:Tempering, ageing and baking of material specimens and material samples, for example in the UF160Incubating several sample series at the same time in research and medicine, for example in the IF110Vibration-free drying of dust- or air-sensitive materials in several batches, for example in the UN110Cooled incubation of larger sample quantities or several parallel test series below room temperature, for example in the IPP110ecoSuitable forModelSizeInterior volume (l)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 detailsHeight560 mmScope of delivery1 mobile base frame, height 560 mmIndividual requirements & procurement serviceFor the flat and the levelling version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €497.08
Memmert levelling base frame B33661, height 130 mm, for sizes 110 and 160
Manufacturer number: B33661

The levelling base frame B33661, with a height of 130 mm, is the flat version for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco and IFbw series in sizes 110 and 160. The size corresponds to the number in the unit name, for example IF110 or UF110.The base frame B29749 with a height of 500 mm is also available for these sizes. The table of compatible models shows which series is available in which size.Typical applicationsUnits of sizes 110 and 160 are placed on the base frame. Typical uses of these units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Tempering larger batches in the pharmaceutical industry, for example in the IF160Production of microscopic specimens in the laboratory, for example in the UN160pa paraffin ovenMaterials testing in industrial quality assurance, for example in the HPP110ecoSuitable forModelSizeInterior volume (l)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 detailsHeight130 mmScope of delivery1 levelling base frame, height 130 mmIndividual requirements & procurement serviceFor the taller version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €273.48
Memmert stacking kit B29744 for sizes 30, 50, 55, 75, 105 and 110
Manufacturer number: B29744

The B29744 stacking kit consists of 4 pieces and is intended for stacking units of the same size. It is intended for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco, HCP and IFbw series in sizes 30, 50, 55, 75, 105 and 110. The size corresponds to the number in the unit name, for example UF30 or UN30.Separate stacking kits are also available for HCP150, HCP240 and for ICO50, 180 and 240 (B42114, B48129, B68362 and B64732). The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorIncubating several sample series at the same time in research and medicine, for example in the IF110Environmental tests and environmental simulations in the HCP105 humidity chamberSuitable forModelSizeInterior volume (l)IF110bw110108UF303032IF110110108UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574IF30plus3032IN30plus3032IF303032IN303032IF55plus5553IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574UN55pa5553UF110plus110108UN110110108UN110plus110108IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032HPP110eco110108HCP505056HCP105105107IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108Scope of delivery1 stacking kit (4 pieces)Individual requirements & procurement serviceFor the stacking kits for HCP humidity chambers and ICO CO₂ incubators, for base frames and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €61.92
Memmert Wandkonsole
Memmert wall bracket B29758 for size 110
Manufacturer number: B29758

The wall bracket B29758 is intended for wall mounting of Memmert units in the I, IFbw, Im, U, UNpa and Um series in size 110. The table of compatible models shows which series is available in this size. The image is a Memmert drawing and is for illustration only. The size corresponds to the number in the unit name, for example IF110 or IN110.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Incubating several sample series at the same time in research and medicine, for example in the IF110Embedding and heating of larger quantities of paraffin or wax, for example in the UN110paSuitable forModelSizeInterior volume (l)IF110110108IN110110108IF110plus110108IN110plus110108IF110bw110108IF110m110108IN110m110108IF110mplus110108IN110mplus110108UF110110108UN110110108UF110plus110108UN110plus110108UN110pa110108UF110m110108UN110m110108UF110mplus110108UN110mplus110108Scope of delivery1 wall bracket for wall mountingIndividual requirements & procurement serviceFor questions about wall mounting and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €302.72
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02073 for sizes 110 and 160
Manufacturer number: B02073

B02073 is a stainless steel slide-in drip tray with a 15 mm rim for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 110 and 160. It collects dripping liquid. According to Memmert, the maximum load is 3 kg per slide-in drip tray. The size corresponds to the number in the unit name, for example IF110 or UF110.Memmert points out that it can impair the spatial temperature distribution. The table of compatible models shows which series is available in which size. The base drip tray for the same unit size is also available (B04359). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Drying laboratory glassware and sample vessels in routine operation, for example in the UF160Embedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenSuitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelRim15 mmMaximum load according to Memmert3 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €117.82
memmert boden abtropfschale
Memmert stainless steel base drip tray B04359 for sizes 110 and 160
Manufacturer number: B04359

The B04359 base drip tray is made of stainless steel and has a 15 mm rim. It is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 110 and 160 and collects dripping liquid. According to Memmert, the maximum load per base drip tray for these sizes is 3 kg. The size corresponds to the number in the unit name, for example IF110 or UF110.In addition, according to Memmert, it can impair the spatial temperature distribution. The table of compatible models shows which series is available in which size. The slide-in drip tray for the same unit size is also available (B02073). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Drying laboratory glassware and sample vessels in routine operation, for example in the UF160Embedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenSuitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelRim15 mmMaximum load according to Memmert3 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €171.14
memmert untergestell nivellierbar
Memmert levelling base frame B29749, height 500 mm, for sizes 110 and 160
Manufacturer number: B29749

B29749 is a levelling base frame with a height of 500 mm for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco and IFbw series in sizes 110 and 160. The size corresponds to the number in the unit name, for example IF110 or UF110.A flat base frame with a height of 130 mm is also available (B33661). The mobile version with a height of 560 mm is also available (B29750). The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsUnits of sizes 110 and 160 are placed on the base frame. Typical uses of these units:Drying laboratory glassware and medium-sized sample series in routine operation, for example in the UF110Parallel incubation of several sample series in research and medicine, for example in the IF160Embedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenStability studies of individual active substance batches according to ICH Q1A in pharmaceutical quality assurance, for example in the HPP110ecoSuitable forModelSizeInterior volume (l)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 detailsHeight500 mmScope of delivery1 levelling base frame, height 500 mmIndividual requirements & procurement serviceFor the flat and the mobile version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €350.88
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68508 for sizes 110 and 160
Manufacturer number: B68508

This stainless steel perforated tray (B68508) is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco, ICP, ICH, HPPeco and IFbw series in sizes 110 and 160. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example IF110 or UF110. The image is for illustration only.According to Memmert, a maximum of 20 kg is permitted per shelf. If you want to load several shelves, also check the maximum load per unit in the data sheet. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying laboratory glassware and medium-sized sample series in routine operation, for example in the UF110Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material specimens and material samples, for example in the UF160Suitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €163.40