Memmert wall bracket B29758 for size 110

The Memmert IF110 incubator has an internal volume of 108 litres and is fitted with two shelves as standard, whilst being designed to accommodate up to five shelves for parallel sample runs. It covers a temperature range of +20 to +80 °C using forced air circulation and can accommodate a total load of up to 175 kg.Interior and forced air circulationThe interior of the IF110 is reinforced with deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system; the housing itself has a fully galvanised sheet steel rear panel. Air circulation is provided by a low-noise turbine that can be adjusted in 10 % increments.Controls and programme functionsThe IF110 is operated via the SingleDISPLAY ControlCOCKPIT; temperature is measured by a DIN Class A Pt100 sensor using a 4-wire measurement system, with a setting accuracy of 0.1 °C. In addition to temperature, recirculation fan speed and exhaust air damper position, the programme duration, time zones and summer and winter time can also be set. A self-diagnostic system assists with fault-finding, and the programme sequence remains stored in the event of a power cut.Safety and door lockingA mechanical temperature limiter, protection class 1 according to DIN 12880, switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature; in addition, electronic temperature monitoring can be set. The fully insulated stainless steel door with an inner glass door locks via a two-point locking mechanism.Finding the right chamber sizeWith two shelves fitted as standard, up to five possible shelves and a maximum total load capacity of 175 kg, the IF110 is designed for parallel sample runs. If a smaller volume is sufficient, the IF75, with a capacity of 74 litres, is the more compact alternative; for larger batches, the IF160 offers more space with a capacity of 161 litres and up to eight shelves.Typical applicationsWith an internal volume of 108 litres, the IF110 is suitable as an incubator for incubating and temperature-controlling several parallel sample series in research, medicine, pharmacy, food analysis and food chemistry.Simultaneous incubation of multiple sample series in research and medicineTemperature control of larger sample quantities in the pharmaceutical industryBatch incubation in food analysis and food chemistryTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangeat least 10 °C above room temperature up to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1x Pt100, DIN Class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 76 kgConnection 230 V50/60 Hz, approx. 1,400 WConnection 115 V (optional)50/60 Hz, approx. 900 WShelves max.5Shelves included in scope of delivery2Max. load on unit175 kgMax. load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 % rel., non-condensingMaximum installation altitude2,000 mMarkingsCE, VDE GS, ULOther sizes in the seriesThe IF series with SingleDISPLAY ranges from 32 to 749 litres internal volume, listed here in ascending order:ModelInternal volumeSet temperatureDisplayIF3032 l+20 to +80 °CSingleDISPLAYIF5553 l+20 to +80 °CSingleDISPLAYIF7574 l+20 to +80 °CSingleDISPLAYIF110 (this page)108 l+20 to +80 °CSingleDISPLAYIF160161 l+20 to +80 °CSingleDISPLAYIF260256 l+20 to +80 °CSingleDISPLAYIF450449 l+20 to +80 °CSingleDISPLAYIF750749 l+20 to +80 °CSingleDISPLAYThis model is also available in the IF-plus series as the IF110plus, featuring TwinDISPLAY and two Pt100 sensors that monitor each other and take over operation in the event of a fault.Scope of deliveryFactory calibration certificate (at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock) and internal glass door, single-leaf2 stainless steel grid shelves, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and Disposal page.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceThe IF110 can be ordered ex-works with, amongst other things, an analogue 4-20 mA interface, a safety lock and an additional Pt100 sensor for temperature monitoring. Available accessories include a roller frame, a wall bracket and additional perforated plates. For qualification and maintenance, we arrange calibration, IQ/OQ/PQ and maintenance services. We are happy to advise you personally on individual requirements or any questions regarding suitable equipment.

The IN110 offers an internal capacity of 108 litres with a maximum of five shelves, two of which are included as standard. The net weight is around 76 kilograms, and the temperature is controlled via a ControlCOCKPIT SingleDISPLAY within the range of +20 to +80 °C.Positioning and air circulationMemmert recommends a minimum clearance of 15 centimetres from the wall, a minimum of 20 centimetres from the ceiling and a minimum of 5 centimetres at the sides. The unit is supplied as standard without castors; a castor frame can be ordered as a factory option. An electronically adjustable exhaust air flap introduces preheated fresh air; the exhaust air outlet with a throttle valve can also be controlled electronically. The interior is reinforced with deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system; the housing has a fully galvanised sheet steel rear panel.Controller and data acquisitionA DIN Class A Pt100 sensor with a 4-wire measurement system supplies the actual temperature to the ControlCOCKPIT; the setting accuracy is 0.1 °C. SetpointWAIT only starts the process time once the setpoint temperature has been reached; three freely selectable temperature values can be calibrated. The programme sequence remains stored in the event of a power failure, and the data logger can be read out via the Ethernet interface.Temperature limitation and door constructionA mechanical temperature limiter, protection class 1 according to DIN 12880, switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature; an adjustable electronic temperature monitoring system complements this safeguard. In front of the inner glass door is a fully insulated stainless steel door with a 2-point locking mechanism and a compression door lock; a self-diagnostic system assists with troubleshooting. The permissible ambient temperature is between +5 °C and +40 °C, with a maximum relative humidity of 80 %.Guide to choosing the right sizeThe smaller IN75 has a capacity of 74 litres with a maximum of six shelves, whilst the IN110 offers an internal volume of 108 litres despite having only five shelves. If more than five shelves are required, the table below lists the IN160 with 161 litres and eight shelves.Typical applicationsThe IN110 is suitable as an incubator with natural convection for incubating and temperature-controlling samples in the range from +20 to +80 °C, including in research applications.Incubation and temperature control of samples across five shelvesUse in medicine, pharmacy, food analysis and food chemistryUse in researchTechnical detailsTemperature setting range+20 to +80 °CWorking temperature rangeAt least 5 °C above room temperature up to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1 Pt100 DIN Class A in 4-wire configurationInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of housing (W x H x D)745 x 864 x 584 mm (depth plus 56 mm for door handle)Net weightapprox. 76 kgConnection 230 V50/60 Hz, approx. 1,400 WConnection 115 V50/60 Hz, approx. 900 WMaximum number of shelves5Shelves included in the scope of delivery2InteriorEasy to clean, reinforced with deep-drawn ribbing, with protected, integrated 4-sided all-round heatingControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 %, non-condensingMaximum installation altitudemax. 2,000 m above sea levelMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe IN series with SingleDISPLAY ranges from 32 to 749 litres internal volume, sorted by internal volume:ModelInternal volumeSetting temperatureDisplayIN3032 l+20 to +80 °CSingleDISPLAYIN5553 l+20 to +80 °CSingleDISPLAYIN7574 l+20 to +80 °CSingleDISPLAYIN110 (this page)108 l+20 to +80 °CSingleDISPLAYIN160161 l+20 to +80 °CSingleDISPLAYIN260256 l+20 to +80 °CSingleDISPLAYIN450449 l+20 to +80 °CSingleDISPLAYIN750749 l+20 to +80 °CSingleDISPLAYThe same capacity is also available with TwinDISPLAY and two Pt100 sensors in the IN-plus series: IN110plus.Scope of delivery1x Memmert IN110 incubatorFactory calibration certificate (calibrated at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door2x stainless steel grid shelf, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and disposal page.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceThe following items, amongst others, can be ordered ex-works for the IN110: interior lighting, an internal power socket, a shatterproof door and feed-throughs of various diameters. Accessories available include reinforced grid shelves, drip trays, levelling feet and a stacking kit; for qualification and re-qualification, we arrange calibration and IQ/OQ services. We are available to assist you personally with bespoke configurations.

The Memmert IF110plus incubator has 108 litres of internal volume with external dimensions of 745 x 864 x 584 mm. Two stainless steel grid shelves are included as standard, and up to five shelves are possible. Control is via the ControlCOCKPIT TwinDISPLAY with two Pt100 sensors that monitor each other, and forced air circulation is provided by an electronically controllable air turbine.Interior, load and connectionThe interior measures 560 x 480 x 400 mm (W x H x D) and is stiffened by deep-drawn ribbing, and the heating is protected and integrated on all four sides. A total load of 175 kg is permitted with a maximum of 20 kg per shelf, and the net weight of the cabinet is around 76 kg. The IF110plus is connected with 230 V at approx. 1,400 W or with 115 V at approx. 900 W, in each case 50/60 Hz. An electronically adjustable exhaust air flap admixes preheated fresh air, and the exhaust air outlet with throttle valve can likewise be controlled electronically.TwinDISPLAY, HeatBALANCE and programmingTwo DIN class A Pt100 sensors monitor each other in 4-wire measurement and automatically take over the function of the other in the event of a fault. The setting accuracy is 0.1 °C, the setting temperature range extends from +20 to +80 °C, and the working temperature range begins at least 10 °C above room temperature. HeatBALANCE allows fine adjustment of the heating power distribution between the upper and lower heating group from -50 to +50 %, and SetpointWAIT starts the process time only after the setpoint temperature has been reached. Three freely selectable temperature values can be calibrated, programmes are programmed, managed and transferred via the Ethernet interface or USB port with the AtmoCONTROL software, and the digital countdown timer can be set from 1 minute to 99 days. A permanently installed sterilisation programme sterilises the interior at 160 °C over 4 hours, not the loaded items.Safety according to DIN 12880A mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum cabinet temperature, and an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can also be selected on the display. The additional AutoSAFETY monitoring automatically follows the setpoint at a freely selectable distance and triggers a visual and audible alarm when the setpoint is exceeded or undershot, and it switches off the heating when exceeded. A self-diagnosis system helps with fault finding. A permissible ambient temperature of +5 °C to +40 °C applies at a maximum of 80 % relative humidity, non-condensing, as well as an installation altitude of up to 2,000 m above sea level. The units must be transported in an upright position.Guide to choosing the right sizeAnyone who has to manage with less floor space but values one more shelf will find an alternative in the smaller IF75plus (74 l, up to 6 shelves). If more capacity is regularly needed, the IF160plus with 161 litres and up to eight shelves offers more space, see the size table below.Typical applicationsAs a forced-air incubator, the IF110plus is designed for incubation and temperature control processes and is used in research, medicine, pharmaceuticals, food analysis and food chemistry.Incubating and temperature control of sample series in researchIncubation processes in medicine and pharmaceuticalsIncubating and temperature control of samples in food analysis and food chemistryTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 10 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 76 kgConnection 230 V50/60 Hz, approx. 1,400 WConnection 115 V50/60 Hz, approx. 900 WShelves max.5Shelves included in scope of delivery2Max. load of unit175 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, SetpointWAIT, AutoSAFETY, visual and audible alarmPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMax. installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe IF-plus series comprises eight sizes from 32 to 749 litres with TwinDISPLAY, listed below sorted by internal volume:ModelInternal volumeSetting temperatureDisplayIF30plus32 l+20 to +80 °CTwinDISPLAYIF55plus53 l+20 to +80 °CTwinDISPLAYIF75plus74 l+20 to +80 °CTwinDISPLAYIF110plus (this page)108 l+20 to +80 °CTwinDISPLAYIF160plus161 l+20 to +80 °CTwinDISPLAYIF260plus256 l+20 to +80 °CTwinDISPLAYIF450plus449 l+20 to +80 °CTwinDISPLAYIF750plus749 l+20 to +80 °CTwinDISPLAYWe also list the same size with one temperature sensor and SingleDISPLAY instead of the two monitoring Pt100 sensors as IF110.Scope of delivery1x Memmert incubator IF110plusFactory calibration certificate (calibration at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door2x stainless steel grid shelves, electropolishedRegulatory informationThe device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the IF110plus, interior lighting, temperature throttling, door-open detection and a lockable door, among other things, can be ordered from the factory. Suitable accessories include additional stainless steel grid shelves and perforated trays, drip trays, a wall bracket, a USB Ethernet adapter and a levelling or mobile base stand. For calibration and qualification, we arrange DAkkS calibrations and IQ/OQ/PQ documentation. For individual requirements, we will advise you personally.

The IN110plus has a capacity of 108 litres with a maximum of five shelves, two of which are fitted as standard, and weighs around 76 kilograms net. The smaller IN75plus, with a capacity of 74 litres, offers as many as six shelves, one more than the larger IN110plus. Temperature control is managed via a ControlCOCKPIT TwinDISPLAY with two Pt100 sensors, operating within a range of +20 to +80 °C.Design and air flowAn electronically adjustable exhaust air flap introduces preheated fresh air, whilst the exhaust air outlet with a throttle valve is electronically controllable. The interior is reinforced by deep-drawn ribbing and features a protected, integrated 4-sided all-round heating system. The IF-plus series of the same size, by contrast, operates with forced air circulation rather than natural convection.HeatBALANCE and sensor technologyHeatBALANCE adjusts the distribution of heating output between the upper and lower heating groups from -50 to +50 %. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays; two DIN Class A Pt100 sensors in a 4-wire configuration monitor each other reciprocally. The setting accuracy is 0.1 °C. Programmes can be managed and transferred via Ethernet or USB using the AtmoCONTROL software.Safety and internal sterilisationA mechanical temperature limiter of protection class 1 according to DIN 12880 serves as a safety measure; it switches off the heating when the temperature reaches approximately 20 °C above the maximum cabinet temperature. An adjustable temperature monitor (protection class 3.1) or an adjustable temperature limiter (protection class 2) can also be selected on the display. AutoSAFETY monitors instances where the temperature exceeds or falls below the setpoint at freely selectable intervals and signals these both visually and acoustically; the sterilisation programme sterilises the interior, not the contents, at 160 °C within 4 hours.Selection guide for the right sizeIf the smaller IN75plus, with a capacity of 74 litres, is no longer sufficient, the IN110plus offers an internal volume of 108 litres, albeit with a maximum of five shelves instead of six. If sample volumes increase further, the table below lists the IN160plus with a 161-litre capacity and eight shelves.Typical applicationsThe IN110plus serves as an incubator with natural convection and HeatBALANCE for incubating and temperature-controlling samples between +20 and +80 °C, including in research applications.Incubating and temperature-controlling samples with redundant sensor monitoringSterilising the interior via the permanently installed programmeUse in researchTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangeAt least 5 °C above room temperature up to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2 Pt100 sensors, DIN Class A, in a 4-wire configuration for mutual monitoring and automatic failover in the event of a faultHeatBALANCE functionAdjustment of the heating power distribution between the upper and lower heating groups from -50 % to +50 %Adjustable temperature monitor/limiterAdjustable temperature monitor (TWW), protection class 3.1, or adjustable temperature limiter (TWB), protection class 2, selectable via the displayAutoSAFETYadditionally integrated over- and under-temperature monitoring ‘ASF’, automatically tracks the setpoint at a freely selectable interval, alarm if the temperature exceeds or falls below the setpoint, heating shut-off if the setpoint is exceededSterilisation programmePermanently installed sterilisation programme (4 hours/160 °C) for sterilising the interior; not intended for sterilising the loadInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of housing (W x H x D)745 x 864 x 584 mm (depth plus 56 mm for door handle)Net weightapprox. 76 kgConnection 230 V50/60 Hz, approx. 1,400 WConnection 115 V50/60 Hz, approx. 900 WMaximum number of shelves5Shelves included in the scope of delivery2InteriorEasy to clean, reinforced with deep-drawn ribbing, with protected, integrated 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displaysPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 % non-condensingMaximum installation heightmax. 2,000 m above sea levelMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe IN-plus series with TwinDISPLAY ranges from 32 to 749 litres internal volume, sorted by internal volume:ModelInternal volumeSet temperatureDisplayIN30plus32 l+20 to +80 °CTwinDISPLAYIN55plus53 l+20 to +80 °CTwinDISPLAYIN75plus74 l+20 to +80 °CTwinDISPLAYIN110plus (this page)108 l+20 to +80 °CTwinDISPLAYIN160plus161 l+20 to +80 °CTwinDISPLAYIN260plus256 l+20 to +80 °CTwinDISPLAYIN450plus449 l+20 to +80 °CTwinDISPLAYIN750plus749 l+20 to +80 °CTwinDISPLAYThe same capacity is also available with SingleDISPLAY and a Pt100 sensor in the IN series: IN110.Scope of delivery1x Memmert IN110plus incubatorFactory calibration certificate (calibrated at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door2x stainless steel grid shelves, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and disposal page.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the IN110plus, the following items, amongst others, can be ordered ex-works: interior lighting, an interior socket, a potential-free contact for fault reporting, and feed-throughs of various diameters. In addition, we offer a USB user ID stick, reinforced grid shelves, levelling feet and a stacking kit. For qualification and requalification, we also arrange calibration and IQ/OQ services. Please do not hesitate to contact us regarding any individual requirements.

The Memmert IF110bw blanket warmer heats non-sterile cloths and blankets reliably and evenly to temperatures between +20 and +80 °C. With an internal capacity of 108 litres and space for up to 5 shelves, the most compact model in the IF-bw series is suitable for facilities where pre-warmed textiles need to be readily available, without any noticeable temperature fluctuations between the individual shelves and without the unit taking up excessive floor space. 4-sided all-round heating for even heat distribution Instead of individual heating zones, a 4-sided all-round heating system surrounds the entire interior, whilst an electronically controlled air circulation system set to a fixed 100 % further ensures an even distribution of heat. A DIN Class A-quality Pt100 sensor with 4-wire measurement measures the temperature with a setting accuracy of 0.1 °C. The operating range extends from at least 10 °C above room temperature up to a maximum of +80 °C, meaning that even moderate heat settings can be achieved cleanly and reproducibly. Uniform heat distribution is particularly noticeable in smaller internal volumes, such as the 108 litres of the IF110bw, as textiles throughout the entire interior reach the same temperature regardless of the selected shelf position. SingleDISPLAY and data logging via Ethernet An adaptive, multifunctional PID microprocessor controller with a high-resolution TFT colour graphic display (SingleDISPLAY) clearly shows the actual and setpoint temperatures and is easy to operate. Log data from the integrated data logger can be read out and managed via the Ethernet interface. A USB port is available as an option; when used in conjunction with the AtmoCONTROL software, this makes it even easier to document and archive processes, for example to verify that a specific temperature range has been reliably maintained. Safety and build quality For added safety, the IF110bw monitors the temperature electronically and also via a mechanical temperature limiter, which triggers at around 20 °C above the maximum temperature. An integrated self-diagnostic system reports faults at an early stage, ensuring that malfunctions are detected before they affect operation. The stainless-steel interior accommodates up to 5 shelves, each with a load capacity of up to 20 kg; two stainless steel grid shelves are included as standard. With a net weight of around 76 kg and robust external dimensions of 745 × 864 × 584 mm (plus 56 mm for the door handle), the unit is designed for long-term, stationary use and can be operated reliably even with daily, repeated use. The right size for every need At 108 litres, the IF110bw is the most compact model in Memmert’s IF-bw range of blanket warmers. If greater capacity is required, the larger models IF260bw (256 litres), IF450bw (449 litres) and IF750bw (749 litres) are also available in the same series, featuring identical control technology and comparable specifications, allowing the appropriate unit size to be flexibly adapted to the actual volume of textiles to be heated. This means that a facility with growing requirements can switch to a larger model within the same product family without having to familiarise itself with a completely different operating system. Safety as a medical device The IF110bw is classified as a Class I medical device and bears the CE marking; it has been tested to VDE, GS and UL standards. For establishments that, in addition to simply heating textiles, also prioritise tested and documented equipment safety, the Class I classification is additional, verifiable information. Combined with electronic temperature monitoring, the mechanical temperature limiter and the integrated self-diagnostic system, this results in a multi-stage safety concept that is suitable for regular, routine use in everyday practice and institutional settings. Typical applications As a blanket warmer with an internal capacity of 108 litres and a temperature range up to +80 °C, the IF110bw is suitable for the following applications: Warming of non-sterile towels and blankets prior to immediate useKeeping several pre-warmed textiles ready for immediate use thanks to up to 5 shelvesUniform temperature control of larger quantities through 4-sided all-round heating and forced circulationDocumented temperature control via the integrated data logger, readable via EthernetSpace-saving addition to rooms with limited floor space thanks to its compact designAn entry-level model in the IF-bw series for facilities with moderate, predictable demand for pre-warmed textiles Technical details Internal capacity108 litres Internal dimensions (W×H×D)560 × 480 × 400 mm (depth minus 39 mm for the fan) External dimensions (W×H×D)745 × 864 × 584 mm (+56 mm door handle) Setting temperature range+20 to +80 °C Working temperature rangeat least 10 °C above room temperature up to +80 °C Setting accuracy0.1 °C Sensors1× Pt100 DIN Class A, 4-wire measurement Heating principle4-sided all-round heating VentilationElectronically controlled air circulation, fixed at 100 % ControlSingleDISPLAY, adaptive PID microprocessor controller, TFT colour graphic display SafetyElectronic temperature monitoring, mechanical temperature limiter (approx. 20 °C above maximum), self-diagnostic system InterfacesEthernet (data logger), USB optional (with AtmoCONTROL software) Shelves2× stainless steel grid shelves included, max. 5 shelves, max. 20 kg per shelf Voltage/Power230 V approx. 1,400 W / 115 V approx. 900 W, 50/60 Hz Net weight/Gross weightapprox. 76 kg / approx. 101 kg Scope of delivery 1× Memmert IF110bw blanket warmer (basic unit) 2× stainless steel grid shelf Regulatory information The IF110bw is classified as a Class I medical device and bears the CE marking; it has been tested to VDE, GS and UL standards. The manufacturer’s (Memmert GmbH + Co. KG, Stiftung EAR) WEEE registration number is DE 66812464. Customised Requirements & Procurement Service Do you require additional accessories such as further stainless steel grid shelves, custom calibration or advice on the appropriate size? Our procurement service will be happy to assist you with special enquiries and spare parts. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.

As a Class I medical device in accordance with Regulation (EU) 2017/745, the Memmert IF110m incubator is used to heat and maintain the temperature of fango, silicate and APS packs in physiotherapy. With an internal volume of 108 litres, it is the smaller of the two IF-m models, with an internal width of 560 mm. Two stainless steel grid shelves are fitted as standard; up to five can be fitted in total.Chamber, door and heatingThe cabinet measures 560 x 480 x 400 mm internally and 745 x 864 x 584 mm externally; its net weight is approximately 76 kg. A fully insulated stainless steel door with a two-point locking mechanism (compression door lock) sits in front of an inner glass door. The deep-drawn, ribbed stainless steel interior is heated on all four sides and can carry a load of 20 kg per shelf; the total permissible load is 175 kg.ControlCOCKPIT SingleDISPLAYAn adaptive PID microprocessor controller with a TFT colour graphic display controls the temperature; measurement is carried out via a DIN Class A Pt100 sensor using 4-wire technology, with a setting accuracy of 0.1 °C. The air turbine can be electronically adjusted in 10 % increments; an exhaust air flap mixes in preheated fresh air, which is then discharged via the exhaust air outlet fitted with a throttle valve. The digital countdown timer covers a range from one minute to 99 days; the ‘SetpointWAIT’ function only starts the process time once the setpoint temperature has been reached. In the event of a power cut, the programme sequence remains stored; data is read out via Ethernet using a time-limited trial version of AtmoCONTROL.Temperature limitationA mechanical temperature limiter, protection class 1 according to DIN 12880, cuts off the heating at approximately 20 °C above the maximum cabinet temperature; this is supplemented by an adjustable electronic temperature monitoring system and a self-diagnostic system for fault detection.Distinction within the product rangeThe IN110m covers the same intended use and chamber size, but operates using natural convection rather than forced air circulation. In the case of the IF110mplus, which is the same size, the intended use changes to the temperature control of rinsing and infusion solutions as well as contrast media, regulated via a ControlCOCKPIT TwinDISPLAY with two displays.Selection guide: other chamber sizesFor smaller quantities, the IF75m is sufficient, with a 74-litre capacity, an internal width of 400 mm, up to six shelves and a maximum total load capacity of 120 kg. If more chamber volume is required, the IF160m is the next option, with a capacity of 161 litres, eight shelves and a maximum total load of 210 kg.Typical applicationsThe intended use of the IF110m as a Class I medical device includes:Heating of fango packs for physiotherapeutic useHeating and maintaining the temperature of silicate packsHeating and maintaining the temperature of APS packsTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangeAt least 10 °C above room temperature up to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1x Pt100, DIN Class A, 4-wire measurementControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)745 x 864 x 584 mmShelves in scope of delivery2Maximum shelves5Max. load capacity of unit175 kgMax. load per shelf20 kgConnection230 V, 50/60 Hz, approx. 1,400 W; 115 V, 50/60 Hz, approx. 900 WNet weightapprox. 76 kgMedical device classificationClass I in accordance with Regulation (EU) 2017/745Intended useHeating and maintaining the temperature of fango, silicate and APS packs in physiotherapyPermissible ambient temperature+5 °C to +40 °CPermissible relative humiditymax. 80 % rh, non-condensingMarkingsCE, VDE, cULus ListedOther sizes in the seriesThe IF110m is one of eight sizes in the IF-m series, ranging from 32 to 749 litres, all featuring SingleDISPLAY and the same setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIF30m32 l+20 to +80 °CSingleDISPLAYIF55m53 l+20 to +80 °CSingleDISPLAYIF75m74 l+20 to +80 °CSingleDISPLAYIF110m (this page)108 l+20 to +80 °CSingleDISPLAYIF160m161 l+20 to +80 °CSingleDISPLAYIF260m256 l+20 to +80 °CSingleDISPLAYIF450m449 l+20 to +80 °CSingleDISPLAYIF750m749 l+20 to +80 °CSingleDISPLAYScope of delivery1x Memmert incubator IF110mFactory calibration certificate (calibrated at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door2x stainless steel wire shelves, electropolishedRegulatory informationThis appliance is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, Memmert GmbH + Co. KG, is DE 66812464. Information on the return of old appliances can be found on our Environment and disposal page. The IF110m is also classified as a Class I medical device in accordance with Regulation (EU) 2017/745, intended for the heating and maintenance of temperature of fango, silicate and APS packs in physiotherapy.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceWhen ordering the IF110m, the 115 V voltage variant, extended overtemperature protection with an additional Pt100 sensor and temperature limitation to fixed values between +50 °C and +75 °C can be specified as factory options. In terms of accessories, we arrange additional and reinforced grid shelves, perforated trays, insert and base drip trays, a wall bracket, a stacking set, a USB-to-Ethernet adapter and a licence for the AtmoCONTROL documentation software. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request. Please contact us to discuss your specific requirements.

With 108 litres internal volume, the Memmert incubator IN110m lies between the IN75m and the IN160m. It is a Class I medical device under Regulation (EU) 2017/745, and its intended purpose is the warming and keeping warm of fango, silicate and APS packs in physiotherapy. Two electropolished stainless steel grid shelves are included as standard, up to five shelves are possible, and the total load goes up to 175 kg.Pt100 sensor, PID controller and time controlThe temperature is measured by a Pt100 sensor of DIN class A using 4-wire technology, and the setting accuracy is 0.1 °C. The control loop is handled by the ControlCOCKPIT SingleDISPLAY: an adaptive, multifunctional PID microprocessor with a high-resolution TFT colour graphic display. The digital countdown timer covers a range from 1 minute to 99 days. Thanks to the SetpointWAIT function, the process time only starts to run once the setpoint temperature has been reached, and three temperature values can be freely calibrated.Ventilation and temperature monitoringNatural ventilation admixes preheated fresh air via an electronically adjustable exhaust air flap, and an equally electronically controllable throttle valve sits at the exhaust air port. Around 20 °C above the maximum cabinet temperature, a mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heating off, supplemented by an adjustable electronic temperature monitoring system. A self-diagnosis system supports fault finding.LoggingAfter a power failure, the program sequence remains stored. Via an Ethernet interface, the data logger can be read out, managed and organised with the time-limited trial version of AtmoCONTROL, and a USB stick with the AtmoCONTROL software is available as an accessory.Interior, door and connectionThe interior is made of easy-care, deep-drawn ribbed stainless steel and is heated on all four sides, and the housing consists of textured stainless steel with a fully galvanised sheet steel rear panel. The fully insulated stainless steel door closes via a 2-point locking system with compression door lock, and behind it there is an inner glass door. Internally, the IN110m measures 560 x 480 x 400 mm, externally 745 x 864 x 584 mm plus 56 mm door handle, and it weighs around 76 kg net. The mains connection is 230 V with approx. 1,400 W or 115 V with approx. 900 W, each 50/60 Hz.Distinction from the IN110 and IN110mplusWithout a medical intended purpose, the Memmert incubator IN110 is available in the same size. The IN110mplus also holds 108 litres, but shows its values via a ControlCOCKPIT TwinDISPLAY instead of SingleDISPLAY and serves a different intended purpose: warming irrigation and infusion solutions and contrast media.Selection guide: which size fitsFor a smaller space requirement, the IN75m with 74 litres offers six instead of five shelves, but only 120 instead of 175 kg total load. Those who need more volume will find it with the IN160m: 161 litres, eight shelves, 210 kg total load.Typical applicationsAs a Class I medical device, the IN110m is intended exclusively for the physiotherapeutic applications named in the intended purpose.Warming of fango packs for physiotherapeutic useWarming and keeping warm of silicate packsWarming and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 5 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of housing (W x H x D)745 x 864 x 584 mm (plus 56 mm door handle)Net weightapprox. 76 kgConnection230 V, 50/60 Hz, approx. 1,400 W; 115 V, 50/60 Hz, approx. 900 WShelves in scope of delivery2Maximum shelves5Max. load of unit175 kgMax. load per shelf20 kgControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeWarming/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rh, non-condensingMarkingsCE, VDE, ULOther sizes in the seriesWithin the IN-m series, the IN110m covers one of eight sizes, the series ranges from 32 to 749 litres, and each version has SingleDISPLAY and the same setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIN30m32 l+20 to +80 °CSingleDISPLAYIN55m53 l+20 to +80 °CSingleDISPLAYIN75m74 l+20 to +80 °CSingleDISPLAYIN110m (this page)108 l+20 to +80 °CSingleDISPLAYIN160m161 l+20 to +80 °CSingleDISPLAYIN260m256 l+20 to +80 °CSingleDISPLAYIN450m449 l+20 to +80 °CSingleDISPLAYIN750m749 l+20 to +80 °CSingleDISPLAYScope of delivery1x Memmert incubator IN110mFactory calibration certificate (calibration at +37 °C)2x stainless steel grid shelf, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal. The IN110m is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of warming and keeping warm of fango, silicate and APS packs in physiotherapy.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the IN110m, Memmert offers options, accessories and services, and options are specified at the factory with the order. We are available for questions about equipment, accessories or spare parts for the IN110m. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert incubator IF110mplus is a class I medical device under Regulation (EU) 2017/745. With 108 litres internal volume, it is the fourth of eight sizes in the mplus series, intended for warming irrigation and infusion solutions and contrast media. Two stainless steel grid shelves are fitted at the factory, and up to five can be inserted in total.Two sensors with function takeoverTwo Pt100 sensors of DIN class A monitor each other in 4-wire measurement, and in the event of a fault, the other takes over the function. The setting temperature range extends from +20 to +80 °C with 0.1 °C setting accuracy. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays, and HeatBALANCE adjusts the heating power distribution between the upper and lower heating group in the range from -50 to +50 %.Programming and time controlVia Ethernet or USB, programs can be created and transferred with AtmoCONTROL, and the program sequence remains stored in the event of a power failure. SetpointWAIT only starts the process time once the setpoint temperature has been reached, and three values can be freely calibrated.AutoSAFETY and sterilisationA mechanical temperature limiter of protection class 1 according to DIN 12880 interrupts the heating at about 20 °C above the maximum cabinet temperature. In addition, an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can be activated on the display. AutoSAFETY automatically follows the setpoint at a freely selectable distance, raises a visual and audible alarm in the event of a deviation, and switches the heating off in the event of an overshoot. A permanently installed sterilisation program (4 h at 160 °C) is used for sterilising the interior and is not intended for sterilising the load.Chamber, door and connectionThe stainless steel interior is deep-drawn ribbed and heated all round, and a fully insulated stainless steel door with 2-point locking and an inner glass door close the chamber. The IF110mplus is connected with 230 V at approx. 1,400 W or with 115 V at approx. 900 W, each 50/60 Hz. Internally the cabinet measures 560 x 480 x 400 mm, externally 745 x 864 x 584 mm, the net weight is around 76 kg, and a total load of 175 kg is permitted at 20 kg per shelf.On the SingleDISPLAY variant and the laboratory deviceWe offer the IF110m with SingleDISPLAY, one instead of two Pt100 sensors and without HeatBALANCE, also a class I medical device, but with a different intended purpose: warming and keeping warm of fango, silicate and APS packs in physiotherapy. Without a medical intended purpose, technically also with TwinDISPLAY, the laboratory incubator IF110plus is available.More or less volumeThose who need less volume but more shelves will find in the IF75mplus 74 litres and six instead of five shelves. More volume and more shelves are offered by the IF160mplus with 161 litres and up to eight shelves.Typical applicationsAs a class I medical device, the following intended purpose applies to the IF110mplus:Warming irrigation solutionsWarming infusion solutionsWarming contrast mediaTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 10 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 76 kgConnection230 V, 50/60 Hz, approx. 1,400 W; 115 V, 50/60 Hz, approx. 900 WShelves in scope of delivery2Maximum shelves5Max. load of unit175 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, AutoSAFETY, SetpointWAIT, programming via AtmoCONTROL (Ethernet/USB)Medical device classificationClass I under Regulation (EU) 2017/745Intended purposeWarming of irrigation and infusion solutions and contrast mediaPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rh, non-condensingMarkingsCE, VDE, cULusOther sizes in the seriesThe mplus series comprises eight chamber sizes from 32 to 749 litres, throughout with TwinDISPLAY and the setting temperature range +20 to +80 °C. With 108 litres, the IF110mplus is the fourth of the eight sizes.ModelInternal volumeSetting temperatureDisplayIF30mplus32 l+20 to +80 °CTwinDISPLAYIF55mplus53 l+20 to +80 °CTwinDISPLAYIF75mplus74 l+20 to +80 °CTwinDISPLAYIF110mplus (this page)108 l+20 to +80 °CTwinDISPLAYIF160mplus161 l+20 to +80 °CTwinDISPLAYIF260mplus256 l+20 to +80 °CTwinDISPLAYIF450mplus449 l+20 to +80 °CTwinDISPLAYIF750mplus749 l+20 to +80 °CTwinDISPLAYScope of delivery1x Memmert incubator IF110mplusFactory calibration certificate at +37 °CFully insulated stainless steel door with 2-point locking (compression door lock)Inner glass door2x stainless steel grid shelves, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal. The IF110mplus is additionally classified as a class I medical device under Regulation (EU) 2017/745; the intended purpose is the warming of irrigation and infusion solutions and contrast media.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceAs factory options, the 115 V voltage variant and temperature limiting (factory limit on the maximum adjustable temperature) are available for the IF110mplus. For accessories, we arrange reinforced and standard grid shelves, perforated trays, drip trays, a wall bracket, a stacking kit, a USB-Ethernet adapter and a levelling or mobile base. For DAkkS calibration, IQ/OQ/PQ documentation and qualification, and maintenance contracts, we arrange the right contact. Contact us for individual advice.

With 108 litres, the Memmert incubator IN110mplus lies in the IN-mplus series between the IN75mplus and the IN160mplus. As a class I medical device under Regulation (EU) 2017/745, it warms irrigation and infusion solutions and contrast media, and up to 175 kg total load is permitted with two grid shelves as standard.Safety technologyA mechanical temperature limiter of protection class 1 according to DIN 12880 disconnects the heating from the mains at around 20 °C above the maximum cabinet temperature. In addition, an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can be selected on the display. AutoSAFETY automatically follows the setpoint at a freely selectable distance, reports deviations visually and audibly, and switches the heating off in the event of an overshoot. A self-diagnosis system supports fault finding, and a permanently installed program with 4 hours at 160 °C is available for sterilising the interior, not intended for the load.Two sensors, one control loopTwo Pt100 sensors of DIN class A work in 4-wire measurement and monitor each other; if one fails, the second automatically takes over its function. Control is via the ControlCOCKPIT TwinDISPLAY with an adaptive PID microprocessor controller and two TFT colour graphic displays. The setpoint temperature can be set between +20 and +80 °C, the setting accuracy is 0.1 °C, and the working temperature range starts at least 5 °C above room temperature.Functions and programmingHeatBALANCE adjusts the heating power distribution between the upper and lower heating group in the range from -50 to +50 %, and SetpointWAIT only starts the process time once the setpoint temperature has been reached. Three temperature values can be freely calibrated, and the program sequence remains stored in the event of a power failure. Via an Ethernet interface or a USB port, the AtmoCONTROL software creates, manages and transfers programs.Construction, loading and connectionThe interior is made of easy-care, deep-drawn ribbed stainless steel with integrated 4-sided all-round heating, and the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. Natural ventilation admixes preheated fresh air via an electronically adjustable exhaust air flap, controlled via an electronically adjustable throttle valve at the exhaust air port. Internal dimensions 560 x 480 x 400 mm, external dimensions 745 x 864 x 584 mm plus 56 mm door handle, net weight around 76 kg. Two grid shelves are included as standard, and up to five shelves are possible at a maximum of 20 kg per shelf and 175 kg total load. Connection is made with 230 V (approx. 1,400 W) or 115 V (approx. 900 W), each 50/60 Hz.The IN110m comparedThe equally sized IN110m is also a Class I medical device, but its intended purpose is the warming and keeping warm of fango, silicate and APS packs in physiotherapy. It is controlled via a SingleDISPLAY with a single Pt100 sensor, while the IN110mplus comes with two displays and two mutually monitoring sensors.Selection guideThe smaller Memmert incubator IN75mplus holds 74 litres and, despite the smaller volume, takes up to six instead of five shelves, at 120 instead of 175 kg total load. More volume is offered by the IN160mplus with 161 litres, up to eight shelves and 210 kg total load.Typical applicationsAs a class I medical device, the IN110mplus is intended for warming irrigation and infusion solutions and contrast media.Warming irrigation solutionsWarming infusion solutionsWarming contrast mediaTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 5 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of housing (W x H x D)745 x 864 x 584 mm (plus 56 mm door handle)Net weightapprox. 76 kgConnection230 V, 50/60 Hz, approx. 1,400 W; 115 V, 50/60 Hz, approx. 900 WShelves in scope of delivery2Maximum shelves5Max. load of unit175 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, SetpointWAIT, AutoSAFETY, visual and audible alarmMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeWarming of irrigation and infusion solutions and contrast mediaPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rh, non-condensingShipping carton (W x H x D)830 x 1,050 x 800 mmMarkingsCE, VDE, ULOther sizes in the seriesThe IN110mplus is one of eight sizes in the IN-mplus series, which ranges from 32 to 749 litres; all models are controlled via TwinDISPLAY in the setting temperature range of +20 to +80 °C.ModelInternal volumeSetting temperatureDisplayIN30mplus32 l+20 to +80 °CTwinDISPLAYIN55mplus53 l+20 to +80 °CTwinDISPLAYIN75mplus74 l+20 to +80 °CTwinDISPLAYIN110mplus (this page)108 l+20 to +80 °CTwinDISPLAYIN160mplus161 l+20 to +80 °CTwinDISPLAYIN260mplus256 l+20 to +80 °CTwinDISPLAYIN450mplus449 l+20 to +80 °CTwinDISPLAYIN750mplus749 l+20 to +80 °CTwinDISPLAYScope of deliveryFactory calibration certificate (calibration at +37 °C)Fully insulated stainless steel door with 2-point locking (compression door lock), inner glass door2x stainless steel grid shelves, electropolishedRegulatory informationThe device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal. The IN110mplus is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of warming irrigation and infusion solutions and contrast media.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the IN110mplus, Memmert offers options, accessories and services, and options are specified at the factory with the order. The requirements for equipment and accessories can be discussed with us, and we take care of the procurement afterwards. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

Anyone wishing to upgrade from a small benchtop unit to a model with significantly greater capacity, without having to install a floor-standing cabinet straight away, will find the Memmert UF110 universal oven to be the obvious intermediate option: 108 litres’ internal volume, a temperature range of 20 to 300 °C and an electronically controlled fan for active heat distribution. With up to 5 shelves and a maximum total load capacity of 175 kg, the UF110 meets the needs of many laboratories that regularly dry or temper several small to medium-sized sample batches in parallel, without the cabinet taking up the floor space of a larger model.Forced air circulation instead of pure convection: faster heating timesThe UF110’s air turbine, which can be electronically controlled in 10 % increments, actively distributes heat throughout the interior, rather than simply allowing it to rise, as is the case with a natural convection cabinet. As a result, the UF110 achieves its operating temperature range from at least 10 °C above room temperature up to 300 °C, with shorter heating-up times than a comparable natural convection model, which, by contrast, operates entirely without any air movement inside the chamber. A Pt100 temperature sensor of DIN Class A in a 4-wire configuration ensures a setting accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards. Those who run many different batches with varying setpoint temperatures will benefit from the active air circulation; dust-sensitive samples, on the other hand, are better suited to the natural convection variant.ControlCOCKPIT SingleDISPLAY and data acquisitionThe UF110 is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphics display. The following parameters can be adjusted: temperature in Celsius or Fahrenheit, the speed of the recirculation fan, the position of the exhaust air damper, the programme duration, as well as the time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWAIT function only starts the process time once the setpoint temperature has actually been reached. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download.Capacity and dimensions of the Memmert UF110 universal ovenThe interior measures 560 x 480 x 400 mm; the external dimensions of the cabinet are 745 x 864 x 584 mm, and the net weight is approximately 74 kg. Two electropolished stainless steel grid shelves are included as standard; up to five shelves can be fitted in total. The maximum total load is 175 kg, with a maximum of 20 kg per shelf. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The UF110 can be connected either to 230 V (approx. 2,800 W) or to 115 V (approx. 1,800 W), in both cases at 50/60 Hz.Selection guide: choosing the right size from the UF rangeThe Memmert UF range is available in eight sizes, with internal volumes ranging from 53 to 1,060 litres. When looking for the right size, you should compare not only the volume but also the footprint and the maximum number of shelves.ModelInternal volumeUF5553 l, footprint 585 x 514 mm, max. 4 shelvesUF7574 l, footprint 585 x 514 mm, max. 6 shelvesUF110108 l, footprint 745 x 584 mm, max. 5 shelvesUF160161 l, footprint 745 x 584 mm, max. 8 shelvesUF260256 l, footprint 824 x 684 mm, max. 9 shelvesUF450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUF750749 l, footprint 1,224 x 784 mm, max. 14 shelvesUF10601,060 l, footprint 1,224 x 1,035 mm, max. 14 shelvesThe UF110 is the obvious choice when the Memmert UF75 universal oven (74 litres, 6 shelves in a smaller footprint) becomes too small for the sample volume, but a larger footprint is not yet available. If you require more volume and more shelves whilst maintaining the same footprint, the Memmert UF160 universal oven (161 litres, 8 shelves instead of 5, same footprint, but taller) is the solution. You can find all sizes in this range in our Climate Chambers & Incubators product range.Distinction: TwinDISPLAY version and its natural convection counterpartThe UF110 described here operates with SingleDISPLAY and a single Pt100 sensor. Anyone requiring redundant temperature monitoring for unattended runs will find this in the Memmert UF110plus universal oven with two Pt100 sensors, TwinDISPLAY, HeatBALANCE and AutoSAFETY. Anyone who can do without active air circulation, for example, because dust-sensitive samples are laid out in the open, will find in the Memmert UN110 universal oven the identical housing with natural convection instead of a fan.Safety according to DIN 12880 for unattended operationIn addition to the adjustable electronic temperature monitoring, the UF110 features a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature, an important safety feature for overnight or weekend runs. An integrated self-diagnostic system assists with fault-finding, whilst the calibration function allows three freely selectable temperature values to be readjusted. The unit bears CE and EAC markings as well as a UL test mark.Installation, operation and disposalWhen operating the UF110, a minimum clearance of 15 cm from the wall and a minimum clearance of 20 cm from the ceiling must be maintained; at the sides, a clearance of at least 5 cm from the wall or an adjacent unit is sufficient. The unit may be installed at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the cabinet is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. As an electrical appliance, the UF110 is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste; see Regulatory information below.Typical applicationsWith an internal volume of 108 litres and active air circulation, the Memmert UF110 universal oven is suitable for laboratories that require more capacity than a standard benchtop unit can provide, but still wish to keep their setup compact.Drying of laboratory glassware and medium-sized sample batches in routine operationsTempering, ageing and stoving of material samplesTesting and curing in quality assuranceMaterial testing in the industrial manufacture of small componentsA second unit alongside a UF75, as the sample volume increasesInvestment rationale: Equipment tailored to the specific purposeThe scope of delivery for the UF110 includes 2 electropolished stainless steel grid shelves; the cabinet is designed to accommodate up to 5 shelves. If you regularly use all the levels, you order additional grid shelves or perforated sheets along with the unit. A fully transparent glass door is available as an option for visual inspection without opening the door, as are interior lighting, an internal power socket and a wall bracket for space-saving installation. If you wish to run unattended cycles with redundant temperature monitoring, opt for the Memmert UF110plus universal oven. A USB-to-Ethernet adapter and AtmoCONTROL software licences are suitable for continuous data logging. For pharmaceutical or standards-governed applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request.Frequently asked questions before making a purchaseHow many samples can the UF110 hold at one time?Two grid shelves are included as standard; up to five shelves, each with a maximum load of 20 kg, are possible, for a total load of up to 175 kg.Can I place the UF110 on a laboratory bench?Yes, with a net weight of around 74 kg and a footprint of 745 x 584 mm, the UF110 is designed for use on a laboratory bench, provided that the bench can safely support the load.Is SingleDISPLAY sufficient for routine operation?For most applications, yes. However, if you wish to run unattended cycles with redundant temperature monitoring, the Memmert UF110plus universal oven with TwinDISPLAY is the better choice.What is the accuracy of the temperature control?Up to 99.9 °C, the setting accuracy is 0.1 °C; from 100 °C onwards, it is 0.5 °C, measured using a DIN Class A Pt100 sensor with 4-wire technology.Is wall mounting possible?A wall bracket is one of the common options for the UF110 and can be selected when placing your order.How does the UF110 differ from the smaller UF75?Both use the same recirculation technology and SingleDISPLAY; the UF110 offers greater capacity, 108 litres instead of 74, and 5 shelves instead of 6, whilst taking up more floor space.Is the UF110 suitable for continuous overnight operation?The mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heater off at an excess temperature of approximately 20 °C and is designed for unattended operation.Technical detailsAdjustable temperature range20 to 300 °COperating temperature rangeat least 10 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mm (depth minus 39 mm for the fan)External dimensions of the housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 74 kg230 V connection50/60 Hz, approx. 2,800 W115 V connection50/60 Hz, approx. 1,800 WMaximum number of shelves5Shelves included in the scope of delivery2Max. load on the unit175 kgMaximum load per shelf20 kgInterior materialsStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelRegulationControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayTimer1 minute to 99 days, digital countdown clockPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation altitude2,000 mLabellingCE, EAC, UL marksScope of delivery1x Memmert UF110 universal ovenFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel doors with a 2-point locking system (compression door lock)2x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert UF110 universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceAccessories available for the UF110 include full-view glass doors, interior lighting and a power socket, a wall bracket, a stacking kit and levelling feet. For data acquisition, a USB-to-Ethernet adapter and AtmoCONTROL software licences, including the AtmoCONTROL FDA version for 21 CFR Part 11, are available. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories, a TwinDISPLAY version, or assistance in selecting the right universal oven for your application? Through our procurement service, we are happy to assist you with procurement and configuration.

The Memmert UN110 universal oven is a heating and drying oven from the Memmert UN series. With an internal volume of 108 litres, it marks the transition from the compact benchtop units of the UN series to a noticeably larger footprint and greater loading capacity, whilst continuing to operate using purely natural convection within a temperature range of 20 to 300 °C. For laboratories that regularly dry, temper or cure larger batches or several batches in parallel, without giving up vibration-free operation, the UN110 is the obvious choice between a compact benchtop unit and a large-volume floor-standing cabinet.Natural convection for larger batchesThe Memmert UN110 universal oven also deliberately does not feature an air turbine or a forced air circulation motor. Heat rises within the chamber purely by convection, without dust or light sample particles being stirred up by a fan. As a result, the working temperature range starts from at least 5 °C above room temperature up to 300 °C. With an internal volume of 108 litres and several shelves occupied simultaneously, uniform natural heat distribution remains crucial, particularly when sensitive or exposed samples must not be affected by air movement. A Pt100 temperature sensor of DIN Class A in a 4-wire configuration ensures a setting accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards.ControlCOCKPIT SingleDISPLAY: Operation and data acquisitionThe UN110 is controlled via the ControlCOCKPIT SingleDISPLAY, an adaptive, multifunctional digital PID microprocessor controller with a high-resolution TFT colour graphics display. You can set the temperature in Celsius or Fahrenheit, as well as the position of the exhaust air flap, the programme duration, the time zone and summer/winter time. A digital countdown timer with target time can be set from 1 minute to 99 days; the SetpointWait function only starts the process time once the setpoint temperature has actually been reached, ensuring reproducible results for larger batches. The data logger can be read out and managed via the Ethernet interface; a time-limited trial version of the AtmoCONTROL software is available for download.Capacity and dimensions of the Memmert UN110 universal ovenThe interior measures 560 x 480 x 400 mm, whilst the external dimensions are 745 x 864 x 584 mm, representing a noticeably larger footprint than the smaller UN30, UN55 and UN75 models. The scope of delivery includes two electropolished stainless steel grid shelves, and the cabinet can accommodate up to five shelves in total. The maximum load capacity is 175 kg for the entire unit and 20 kg per shelf. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The UN110 is connected to either 230 V (approx. 2,800 W) or 115 V (approx. 1,800 W), in each case at 50/60 Hz.Selection guide: moving to a larger floor areaThe Memmert UN series with natural convection covers internal volumes ranging from 32 to 749 litres. The UN110 is the first model in the range to feature a noticeably larger footprint compared with the three smaller benchtop models.ModelInternal volumeUN3032 l, footprint 585 x 434 mm, 3 shelves max.UN5553 l, footprint 585 x 514 mm, max. 4 shelvesUN7574 l, footprint 585 x 514 mm, max. 6 shelvesUN110108 l, footprint 745 x 584 mm, 5 shelves max.UN260256 l, footprint 824 x 684 mm, max. 9 shelvesUN450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUN750749 l, footprint 1,224 x 784 mm, max. 14 shelvesAnyone upgrading from the UN75 (74 litres, same footprint as the UN55) who requires more capacity and a higher load capacity per unit will find the UN110 to be the suitable next step. If even that is no longer sufficient, the Memmert UN260 universal oven offers a significantly larger, freestanding model with a capacity of 256 litres. The full range of climate chambers and incubators can be found under Climate Chambers & Incubators.Distinction: natural convection versus forced-air circulationAnyone requiring more active heat distribution and shorter heating times for similar volumes, for example, with densely packed batches of varying sizes, will find the Memmert UF160 universal oven to be the suitable forced air circulation counterpart, featuring an electronically controllable air turbine. Its working temperature range starts at 10 °C rather than 5 °C above room temperature. For samples sensitive to dust or air movement, the natural convection of the UN110 remains the more suitable choice. A significantly more compact natural convection model for smaller sample quantities is the Memmert UN30 universal oven. Like all standard models in the UN series, the UN110 operates with the ControlCOCKPIT SingleDISPLAY, rather than the TwinDISPLAY reserved for the ‘plus’ variants.Safety according to DIN 12880 even for larger batchesThe UN110 features adjustable electronic temperature monitoring and a mechanical temperature limiter (protection class 1 according to DIN 12880), which switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature, an important safety feature for overnight or weekend runs when several shelves are in use simultaneously. A self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. The unit bears CE and EAC markings as well as a UL test mark.Installation, operation and disposalFor operation, a minimum clearance of 15 cm from the wall and a minimum clearance of 20 cm from the ceiling must be maintained; a minimum clearance of 5 cm is sufficient on either side from the wall or an adjacent unit. With a net weight of around 74 kg, it is recommended that the UN110 be placed on a sturdy, load-bearing base rather than simply on a laboratory bench. It may be installed at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the UN110 is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. As an electrical appliance, the UN110 is subject to the German Electrical and Electronic Equipment Act (ElektroG) at the end of its service life and must not be disposed of with household waste.Typical applicationsWith an internal volume of 108 litres and a load capacity of up to 175 kg, the Memmert UN110 universal oven is suitable for laboratories and businesses that regularly dry or heat-treat large quantities of samples.Drying large quantities of laboratory glassware and sample containersVibration-free drying of dust- or air-sensitive materials in multiple batchesTempering, ageing and firing of material samples in industrial quality assuranceMaterial tests with a higher sample throughput than with the smaller UN modelsScience and research involving varying, sometimes larger, seriesInvestment rationale: Equipment for higher throughputThe scope of delivery for the UN110 includes 2 electropolished stainless steel grid shelves; the cabinet is designed to accommodate up to 5 shelves, each with a maximum load of 20 kg. If you regularly use all levels, you can add further grid shelves or perforated trays. For visual inspection without opening the door, a full-view glass door is available, along with interior lighting and a socket for additional measuring equipment, as well as a levelling or mobile base for flexible repositioning. For gas-tight applications, a corresponding version including gas supply and exhaust is available. For continuous data logging, an AtmoCONTROL software licence is recommended; for applications subject to standards, calibration and IQ/OQ/PQ services are available, including DAkkS calibration on request.Frequently asked questions before making a purchaseWhen is the UN110 a good choice?Compared with compact benchtop units, it offers a significantly larger internal volume and a more robust base, without sacrificing the benefits of natural convection.Will the UN110 still fit on a laboratory bench?With a net weight of around 74 kg and a footprint of 745 x 584 mm, a sturdy, load-bearing base is recommended rather than a standard laboratory bench.How many samples can be loaded at the same time?Up to 5 shelves, each with a maximum load of 20 kg, giving a total load capacity of up to 175 kg.What is the accuracy of the temperature control?The DIN Class A Pt100 sensor, using 4-wire technology, provides an accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards, regardless of the cabinet size within the UN series.Is the UN110 also available with forced air circulation?The direct counterpart with forced air circulation in a similar size range is the Memmert UF160 universal oven, with a capacity of 161 litres and an electronically controlled air turbine.Is a gas-tight design possible?Yes, a virtually gas-tight interior with gas inlet and outlet connections is one of the common options for the UN110.Is the UN110 suitable for unattended operation?The mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating if the temperature rises by approximately 20 °C and is designed for night-time or weekend operation.Technical detailsSetting temperature range20 to 300 °CWorking temperature rangeat least 5 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensorPt100, DIN Class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of the housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 74 kg230 V connection50/60 Hz, approx. 2,800 W115 V connection50/60 Hz, approx. 1,800 WMaximum number of shelves5Shelves included in the scope of delivery2Max. load on the unit175 kgMaximum load per shelf20 kgInterior materialsStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphics displayTimer1 minute to 99 days, digital countdown clockPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation altitude2,000 mLabellingCE, EAC, UL test markScope of delivery1x Memmert UN110 universal ovenFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel doors with a 2-point locking system (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe Memmert UN110 universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceThe UN110 is available with, amongst other features, full-view glass doors, interior lighting and a power socket, a levelling or mobile base frame, reinforced grid shelves and perforated trays, as well as a gas-tight version with various pipe feed-throughs. A USB-to-Ethernet adapter and AtmoCONTROL software licences are available for data acquisition. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories or assistance in selecting the right universal oven for your application? Through our procurement service, we are happy to assist you with procurement and configuration.

The Memmert UF110plus universal oven incorporates the series’ TwinDISPLAY safety features in a unit with 108 litres of internal volume, a temperature range of 20 to 300 °C and two redundant Pt100 sensors that monitor each other. With up to 5 shelves and a maximum total load of 175 kg, it offers the same capacity as the base model UF110, supplemented by HeatBALANCE and AutoSAFETY for unattended processes.Forced air circulation with redundant temperature measurementThe UF110plus’s air turbine, which can be electronically controlled in 10 % increments, actively distributes heat throughout the chamber and operates within a temperature range of at least 10 °C above room temperature up to 300 °C. Two DIN Class A Pt100 sensors in a 4-wire configuration monitor each other; if one fails, the second automatically takes over its function. The setting accuracy is 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards. Preheated fresh air is introduced via an electronically adjustable exhaust air damper; the exhaust air outlet with throttle valve can also be controlled electronically.ControlCOCKPIT TwinDISPLAY: HeatBALANCE and AutoSAFETYThe UF110plus is controlled via the ControlCOCKPIT TwinDISPLAY, which features two high-resolution TFT colour graphic displays. The HeatBALANCE function allows for fine-tuning of the heat output distribution between the upper and lower heating groups from -50 to +50 %. AutoSAFETY also monitors over- and under-temperature conditions, automatically tracks the setpoint within a freely selectable tolerance range and triggers visual and audible alarms in the event of a deviation; if the setpoint is exceeded, the heating system switches off. Programmes are programmed, managed and transferred via an Ethernet interface or USB port using the AtmoCONTROL software. A programmable door lock and a door-open detection system can be added as optional extras.Capacity and dimensions of the Memmert UF110plus universal ovenThe internal dimensions are 560 x 480 x 400 mm; the external dimensions of the housing are 745 x 864 x 584 mm, and the net weight is approximately 74 kg, identical to that of the base model UF110. Two electropolished stainless steel grid shelves are included as standard; up to five shelves can be fitted in total. The maximum total load is 175 kg, with a maximum of 20 kg per shelf. The interior consists of easy-to-clean stainless steel, reinforced by deep-drawn ribbing, with protected, integrated 4-sided all-round heating; the housing is made of textured stainless steel with a fully galvanised sheet steel rear panel. The UF110plus can be connected either to 230 V (approx. 2,800 W) or 115 V (approx. 1,800 W), in both cases at 50/60 Hz.Selection guide: choosing the right size from the UF rangeThe Memmert UF range with forced air circulation comprises eight models with internal volumes ranging from 53 to 1,060 litres, each of which is also available with TwinDISPLAY. When selecting the right size, the key factors to consider, alongside the volume, are the footprint and the number of shelves required.ModelInternal volumeUF5553 l, footprint 585 x 514 mm, max. 4 shelvesUF7574 l, footprint 585 x 514 mm, max. 6 shelvesUF110108 l, footprint 745 x 584 mm, max. 5 shelvesUF160161 l, footprint 745 x 584 mm, max. 8 shelvesUF260256 l, footprint 824 x 684 mm, max. 9 shelvesUF450449 l, footprint 1,224 x 784 mm, max. 8 shelvesUF750749 l, footprint 1,224 x 784 mm, max. 14 shelvesUF10601,060 l, footprint 1,224 x 1,035 mm, max. 14 shelvesThe UF110plus is the obvious choice when the Memmert UF75plus universal oven (74 litres) has reached its capacity limit, but you still wish to continue using TwinDISPLAY. If you require more volume and more shelves whilst maintaining the same footprint, you will find these in the Memmert UF160plus universal oven (161 litres, 8 shelves instead of 5, same footprint). You can find all sizes in the range in our Range of climate chambers & Incubators.Distinction: TwinDISPLAY versus SingleDISPLAY, and natural convectionAnyone who can do without sensor redundancy can save money with the Memmert UF110 universal oven in the basic model with SingleDISPLAY. For samples that are sensitive to dust or air movement and cannot tolerate active air circulation, the Memmert UN110plus universal oven offers the same housing, but with natural convection instead of an air turbine, and still featuring TwinDISPLAY. Anyone needing more capacity whilst maintaining the same footprint will find it in the Memmert UF160plus universal oven.Safety according to DIN 12880, enhanced by AutoSAFETYIn addition to the adjustable electronic temperature monitoring and AutoSAFETY, the UF110plus is fitted with a mechanical temperature limiter of protection class 1 according to DIN 12880, which switches off the heating when the temperature rises to approximately 20 °C above the maximum cabinet temperature. The display also allows you to select either an adjustable temperature monitor (Protection Class 3.1) or an adjustable temperature limiter (Protection Class 2). An integrated self-diagnostic system assists with fault-finding, and three freely selectable temperature values can be calibrated. The unit bears CE and EAC markings as well as a UL mark.Installation, operation and disposalFor operation, a minimum distance of 15 cm from the wall and a minimum distance of 20 cm from the ceiling must be maintained; a minimum of 5 cm is sufficient on either side in relation to the wall or an adjacent unit. The unit may be installed at altitudes of up to 2,000 m above sea level at an ambient temperature of 5 °C to 40 °C and a relative humidity of no more than 80 %, non-condensing. Electrically, the UF110plus is designed for overvoltage category II and pollution degree 2; it must only be transported in an upright position. The interior, made of easy-to-clean stainless steel, can be cleaned using standard laboratory cleaning agents. As an electrical appliance, the UF110plus is subject to the Electrical and Electronic Equipment Act at the end of its service life and must not be disposed of with household waste; see Regulatory information below.Typical applicationsWith an internal volume of 108 litres and redundant sensors, the Memmert UF110plus universal oven is suitable for laboratories that require capacity and do not want to compromise on process reliability.Unattended drying of medium-sized batches overnight or at the weekendTempering, ageing and firing of material samples subject to documentation requirementsTesting and curing in quality assurance where higher safety standards are requiredMaterial testing in the industrial manufacture of small to medium-sized componentsA second unit to complement a UF75plus as the sample volume increasesInvestment rationale: when TwinDISPLAY is worthwhileThe scope of delivery for the UF110plus includes 2 electropolished stainless steel grid shelves; the cabinet is designed to accommodate up to 5 shelves. TwinDISPLAY is particularly beneficial where processes run unattended overnight and a sensor failure would jeopardise the batch. Those who do not require this redundancy can save money by opting for the Memmert UF110 universal oven in its basic model. A fully transparent glass door is available as an option for visual inspection without opening the door, as is a programmable door lock with door-open detection and a wall bracket for space-saving installation. A USB-to-Ethernet adapter and AtmoCONTROL software licences are available for continuous logging. For pharmaceutical or standards-compliant applications, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request.Frequently asked questions before making a purchaseWhat exactly are the benefits of the second Pt100 sensor?The two sensors monitor each other; if one fails, the other automatically takes over its function without the drying process having to be interrupted.How many samples can the UF110plus hold at any one time?Two grid shelves are included as standard; it can accommodate up to five shelves, each with a maximum load of 20 kg, for a total load capacity of up to 175 kg.Can I place the UF110plus on a laboratory bench?The net weight is around 74 kg with a footprint of 745 x 584 mm. Whether a laboratory bench is suitable depends on whether it can safely support this load.Is TwinDISPLAY worth it for routine operation?For simple drying tasks during the day, SingleDISPLAY is usually sufficient. For unattended overnight runs, the UF110plus is the safer choice compared to the Memmert UF110 universal oven.What is the accuracy of the temperature control?Both Pt100 sensors of DIN Class A operate using a 4-wire measurement system and achieve an accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C onwards.Is a natural convection version available with TwinDISPLAY?Yes, the Memmert UN110plus universal oven shares the same housing as the UF110plus, but operates without an air turbine.Is a programmable door lock available?Yes, a programmable door lock and door-open detection are options available exclusively on TwinDISPLAY devices such as the UF110plus.How does the UF110plus differ from the larger UF160plus?Both models feature TwinDISPLAY and two redundant Pt100 sensors; the UF160plus offers greater capacity, 161 litres instead of 108, and 8 shelves instead of 5, whilst occupying the same floor space, but is taller in design.Technical detailsAdjustable temperature range20 to 300 °COperating temperature rangeat least 10 °C above room temperature up to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN Class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mm (depth minus 39 mm for the fan)External dimensions of the housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 74 kg230 V connection50/60 Hz, approx. 2,800 W115 V connection50/60 Hz, approx. 1,800 WMaximum number of shelves5Shelves included in scope of delivery2Max. load on the unit175 kgMax. load per shelf20 kgInterior materialsStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel rear panelRegulationControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displaysAdditional functionsHeatBALANCE, AutoSAFETY, visual and audible alarmPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % relative humidity, non-condensingMaximum installation height2,000 mLabellingCE, EAC, UL marksScope of delivery1x Memmert UF110plus universal ovenFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel doors with a 2-point locking system (compression door lock)2x stainless steel grid shelf, electropolishedRegulatory informationThe Memmert UF110plus universal oven is registered with the Stiftung Elektro-Altgeräte Register (Stiftung EAR) under WEEE registration number DE 66812464.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceAccessories available for the UF110plus include full-view glass doors, interior lighting and a power socket, a wall bracket, a stacking kit, levelling feet and a USB user ID stick for TwinDISPLAY user rights. For data acquisition, a USB-to-Ethernet adapter and AtmoCONTROL software licences, including the AtmoCONTROL FDA version for 21 CFR Part 11, are available. In addition, we arrange calibration, IQ/OQ/PQ and maintenance services, including DAkkS calibration on request. Do you require any of these accessories or assistance in selecting the right universal oven for your application? Through our procurement service, we’d be happy to assist you with procurement and configuration.

With an interior volume of 108 litres and a net weight of around 74 kg, the Memmert UN110plus universal oven is the fourth of eight sizes in the UN-plus series. Heating is by natural convection alone, without an air turbine, and the setting temperature range extends from +20 to +300 °C. Two DIN class A Pt100 sensors monitor each other in 4-wire measurement and automatically take over the function of the other in the event of a fault.Interior and loadThe interior measures 560 x 480 x 400 mm and is deep-drawn ribbed with protected, integrated 4-sided all-round heating, and the external dimensions are 745 x 864 x 584 mm plus 56 mm for the door handle. Two stainless steel grid shelves are part of the standard equipment, and up to five shelves are possible. A total load of 175 kg is permitted with a maximum of 20 kg per shelf, and the housing has a fully galvanised sheet steel rear wall.Safety technology and HeatBALANCEA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum oven temperature, and an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can additionally be selected on the display. AutoSAFETY automatically follows the setpoint at a freely selectable distance and reports deviations visually and audibly. With HeatBALANCE, the heating power distribution between the upper and lower heating group can additionally be adjusted from -50 to +50 %, and a self-diagnosis system helps with fault finding.Control and programmingThe oven is controlled via the ControlCOCKPIT with two TFT colour graphic displays, and the setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C. The SetpointWAIT function starts the process time only after the setpoint temperature has been reached, and a digital countdown timer covers target times from 1 minute to 99 days. The UN110plus is connected with 230 V at approx. 2,800 W, 115 V at approx. 1,800 W is available as a factory option at no extra charge, and programming is via the Ethernet interface or USB port with the AtmoCONTROL software.Guide to choosing the right sizeAnyone who can manage with less volume and up to 120 kg total load will find the more compact model in the UN75plus with 74 litres, which, because of its taller interior, even accommodates up to six shelves. For more capacity with larger batches, the UN160plus with 161 litres, up to eight shelves and 210 kg permitted total load offers more reserve, see the size table below.Typical applicationsThe UN110plus is used in research, science, industry and quality assurance for drying and heating samples and materials.Drying and heating medium-sized sample series in laboratory operationDrying and heating in industry and quality assuranceDrying in research and science with up to five shelves at the same timeTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 5 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of housing (W x H x D)745 x 864 x 584 mm (plus 56 mm door handle)Net weightapprox. 74 kgConnection 230 V50/60 Hz, approx. 2,800 WConnection 115 V (factory option)50/60 Hz, approx. 1,800 WShelves max.5Shelves included in scope of delivery2Max. load of unit175 kgMax. load per shelf20 kgInteriordeep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, AutoSAFETY, visual and audible alarmPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMax. installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe UN-plus series with natural convection comprises eight sizes from 32 to 749 litres, listed below sorted by internal volume:ModelInternal volumeSetting temperatureDisplayUN30plus32 l+20 to +300 °CTwinDISPLAYUN55plus53 l+20 to +300 °CTwinDISPLAYUN75plus74 l+20 to +300 °CTwinDISPLAYUN110plus (this page)108 l+20 to +300 °CTwinDISPLAYUN160plus161 l+20 to +300 °CTwinDISPLAYUN260plus256 l+20 to +300 °CTwinDISPLAYUN450plus449 l+20 to +300 °CTwinDISPLAYUN750plus749 l+20 to +300 °CTwinDISPLAYWith SingleDISPLAY, the same volume is available in the UN series: UN110.Scope of delivery1x Memmert universal oven UN110plusFactory calibration certificate (calibration at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the UN110plus, a full-view glass door, interior lighting and socket, a programmable door lock and door-open detection, among other things, can be ordered ex works. Suitable accessories include additional grid shelves and perforated trays, drip trays, a wall bracket, a USB Ethernet adapter and a base stand. For factory and DAkkS calibration and IQ and OQ documentation, we put you in touch with the right contact. For individual requirements, we will advise you personally.

The Memmert UN110pa paraffin oven holds 108 litres, and two stainless steel grid shelves are part of the scope of delivery. The nearly gas-tight interior heats paraffin and other embedding media evenly in the range from +20 to +80 °C, controlled via two redundant Pt100 sensors on the TwinDISPLAY. Up to five shelves can be loaded with a maximum total load of 175 kg.Interior for larger batchesThe interior measures 560 x 480 x 400 mm, and the housing measures 745 x 864 x 584 mm externally plus 56 mm for the door handle. Two electropolished stainless steel grid shelves are part of the standard equipment, and up to three more fit in addition. The fully insulated stainless steel door closes via 2-point locking as a compression door lock, and the housing has a fully galvanised sheet steel rear wall.Two heating groups with HeatBALANCEThe heating power distribution between the upper and lower heating group can be adjusted via HeatBALANCE from -50 to +50 %. Display and control are via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays, and the two DIN class A Pt100 sensors measure in 4-wire technology, monitor each other and automatically take over the function of the other in the event of a fault. The setting accuracy is 0.1 °C, and SetpointWAIT lets the process time begin only once the setpoint temperature has actually been reached.Safety reservesA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at about 20 °C above the maximum oven temperature. An adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can also be selected. AutoSAFETY runs in parallel, follows the setpoint at a freely selectable distance and raises a visual and audible alarm in the event of deviation, and a self-diagnosis system supports fault finding.Guide to choosing between UN75pa and UN160paIf 108 litres are no longer enough, the UN160pa with 161 litres has more capacity, see the size table below. If less volume is sufficient, the UN75pa with 74 litres is the more compact alternative with the same control and safety equipment.Difference from the UN110 universal ovenThe universal oven UN110 of the same size also holds 108 litres, but goes up to +300 °C and is controlled via a SingleDISPLAY. The UN110pa stops at a maximum of +80 °C, but with a second Pt100 sensor, TwinDISPLAY, HeatBALANCE and the nearly gas-tight interior for paraffin and other embedding media.Typical applicationsWith 108 litres, the UN110pa covers sample preparation in histology, pathology and microbiology and evenly heats larger quantities of embedding media such as paraffin or wax.Embedding and heating larger quantities of paraffin or waxSample preparation in pathology and microbiologyProduction of microscopic specimens for teaching and researchTechnical detailsSetting temperature range+20 to +80 °CWorking temperature rangemin. 5 °C above room temperature to +80 °CTemperature setting accuracy0.1 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 480 x 400 mmExternal dimensions of housing (W x H x D)745 x 864 x 584 mm (plus 56 mm for door handle)Net weightapprox. 75 kgConnection 230 V50/60 Hz, approx. 1,400 WConnection 115 V50/60 Hz, approx. 900 W (factory option X2, no extra charge)Shelves max.5Shelves included in scope of delivery2Max. load of unit175 kgMax. load per shelf20 kgInteriornearly gas-tight, deep-drawn ribbed, 4-sided all-round heatingControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, SetpointWAIT, AutoSAFETY, visual and audible alarmPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMax. installation altitude2,000 mMarkingsCE, VDE GS, UL, EACOther sizes in the seriesThe UN-pa paraffin oven series comprises five sizes from 32 to 161 litres, listed below sorted by internal volume:ModelInternal volumeSetting temperatureDisplayUN30pa32 l+20 to +80 °CTwinDISPLAYUN55pa53 l+20 to +80 °CTwinDISPLAYUN75pa74 l+20 to +80 °CTwinDISPLAYUN110pa (this page)108 l+20 to +80 °CTwinDISPLAYUN160pa161 l+20 to +80 °CTwinDISPLAYScope of delivery1x Memmert paraffin oven UN110paFactory calibration certificate (calibration at +80 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe device is an electrical device within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the UN110pa, a full-view glass door, gas inlet and outlet and door-open detection, among other things, can be ordered from the factory. The accessories range includes additional shelves and perforated sheets, drip trays, a wall bracket, a USB Ethernet adapter and a mobile base stand. We arrange calibration, IQ/OQ and maintenance services on request, as well as individual advice on suitable equipment.

The Memmert universal oven UF110m has 108 litres of internal volume and sits in the UF-m series between the UF75m with 74 litres and the UF160m with 161 litres. As a Class I medical device under Regulation (EU) 2017/745, the UF110m is also intended exclusively for the heating and keeping warm of fango, silicate and APS packs, controlled via the ControlCOCKPIT SingleDISPLAY with one Pt100 sensor.Control and safety of the UF110m in detailThe ControlCOCKPIT SingleDISPLAY is at the centre of operation: an adaptive PID microprocessor controller that controls temperature, forced air circulation speed, exhaust air flap position and program run time via a TFT colour graphic display, supplemented by a countdown timer from 1 minute to 99 days and SetpointWAIT for the delayed start of the process time. Heat distribution in the 108-litre interior is provided by an air turbine that is electronically controllable in 10 % steps. The setting temperature range extends from 20 to 300 °C with a setting accuracy of 0.1 °C up to 99.9 °C and 0.5 °C from 100 °C, measured by a DIN class A Pt100 sensor. In the event of a power failure, the program run remains stored and can be read out via Ethernet with AtmoCONTROL. On the safety side, a DIN 12880 temperature limiter of protection class 1 complements the electronic monitoring, and a self-diagnosis system assists with troubleshooting.Selection guide within the UF-m seriesThe housing is 864 mm high and 584 mm deep, plus 56 mm for the door handle, and the net weight is around 74 kg. The cabinet is transported upright, and at the installation site a distance of at least 15 cm from the wall and at least 5 cm at the sides must be observed. The interior of 560 x 560 x 480 mm holds up to 5 shelves, with a load capacity of 20 kg per shelf and 175 kg in total. One size smaller is the UF75m with 74 litres and up to 6 shelves, and one size larger is the UF160m with 161 litres and up to 8 shelves. For two redundant sensors and two displays, the sister model UF110mplus is available, and as a laboratory unit without classification as a medical device there is the Memmert universal oven UF110.Typical applicationsAs a Class I medical device, the Memmert universal oven UF110m is intended exclusively for physiotherapeutic applications with fango, silicate and APS packs.Heating of fango packs for physiotherapeutic useHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsAdjustable temperature range20 to 300 °CWorking temperature rangemin. 10 °C above room temperature to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 560 x 480 mm (depth minus 39 mm for the fan)External dimensions of housing (H x D)864 x 584 mmNet weightapprox. 74 kgGross weight (packed)approx. 99 kgPackaging dimensions (W x H x D)830 x 1,050 x 800 mmConnection 230 V50/60 Hz, approx. 2,800 WConnection 115 V50/60 Hz, approx. 1,800 WMaximum number of shelves5Shelves included in scope of delivery2Max. load of unit175 kgMax. load per shelf20 kgInterior materialStainless steel, 4-sided all-round heatingHousing materialTextured stainless steel, galvanised sheet steel back panelControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic displayPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rel., non-condensingMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyMarkingsCE, VDE, UL test marksOther sizes in the seriesThe UF-m series comprises nine sizes between 32 and 1,060 litres of internal volume, all with ControlCOCKPIT SingleDISPLAY and an identical intended purpose for physiotherapy.ModelInternal volumeSetting temperatureDisplayUF30m32 l+20 to +300 °CSingleDISPLAYUF55m53 l+20 to +300 °CSingleDISPLAYUF75m74 l+20 to +300 °CSingleDISPLAYUF110m (this page)108 l+20 to +300 °CSingleDISPLAYUF160m161 l+20 to +300 °CSingleDISPLAYUF260m256 l+20 to +300 °CSingleDISPLAYUF450m449 l+20 to +300 °CSingleDISPLAYUF750m749 l+20 to +300 °CSingleDISPLAYUF1060m1,060 l+20 to +300 °CSingleDISPLAYThe UF110m is also available with two displays and two redundant sensors as the UF110mplus. As a laboratory unit without classification as a medical device, we also offer the Memmert universal oven UF110.Scope of delivery1x Memmert universal oven UF110mFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)2x stainless steel grid shelf, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. In addition, the Memmert universal oven UF110m is classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor options, accessories and spare parts for the UF110m, we provide individual advice tailored to the workflows in your practice. Please contact us with your specific requirements. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert universal oven UN110m holds 108 litres with an internal width of 560 mm and is one of the mid-sized models in the UN-m series. As a Class I medical device under Regulation (EU) 2017/745, it is intended for the heating and keeping warm of fango, silicate and APS packs in physiotherapy, and two stainless steel grid shelves are included as standard.Functions and air flowThe digital countdown timer can be set from 1 minute to 99 days, and with SetpointWAIT the process time only begins once the setpoint temperature has been reached. Natural convection without a forced air circulation fan characterises the UN110m, an electronically adjustable exhaust air flap supplies preheated fresh air, and a throttle flap regulates at the exhaust air port. The data logger can be read out via Ethernet.Safety and controlThe equipment includes a Pt100 sensor of DIN class A with 4-wire measurement and a setting accuracy of 0.1 °C below and 0.5 °C above 100 °C, as well as a mechanical temperature limiter TB of protection class 1 according to DIN 12880, which disconnects the heating around 20 °C above the maximum cabinet temperature. Adjustable electronic temperature monitoring and a self-diagnosis system for troubleshooting round off the equipment.Loading and connectionThe permissible total load is 175 kg at 20 kg per shelf, and up to five shelves fit inside. Connection is at 230 V with approx. 2,800 W or at 115 V with approx. 1,800 W, in each case 50/60 Hz. The internal dimensions are 560 x 560 x 480 mm, the net weight is around 74 kg and the packed weight around 99 kg, with packaging dimensions of 830 x 1,050 x 800 mm.Difference from the laboratory ovenWithout a medical intended purpose, we offer the Memmert universal oven UN110 for laboratories and industry in the same chamber size. Within the medical device line, the UN110m is also available as the UN110mplus with two displays for control.Selection guideThe next smaller UN75m offers 74 litres with six shelves and a 120 kg total load, and the next larger UN160m reaches 161 litres, eight shelves and a 210 kg total load.Typical applicationsHeating of fango packs for physiotherapyHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsAdjustable temperature range+20 to +300 °CWorking temperature rangemin. 5 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor1x Pt100, DIN class A, 4-wire measurementInternal volume108 lInternal dimensions (W x H x D)560 x 560 x 480 mmNet weightapprox. 74 kgConnection230 V, 50/60 Hz, approx. 2,800 W; 115 V, 50/60 Hz, approx. 1,800 WShelves included in scope of delivery2Maximum number of shelves5Max. load of unit175 kgMax. load per shelf20 kgControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller with TFT colour graphic displayMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature+5 °C to +40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe UN-m series is divided into eight sizes from 32 to 749 litres, each size with SingleDISPLAY and a setting temperature range of +20 to +300 °C.ModelInternal volumeSetting temperatureDisplayUN30m32 l+20 to +300 °CSingleDISPLAYUN55m53 l+20 to +300 °CSingleDISPLAYUN75m74 l+20 to +300 °CSingleDISPLAYUN110m (this page)108 l+20 to +300 °CSingleDISPLAYUN160m161 l+20 to +300 °CSingleDISPLAYUN260m256 l+20 to +300 °CSingleDISPLAYUN450m449 l+20 to +300 °CSingleDISPLAYUN750m749 l+20 to +300 °CSingleDISPLAYScope of delivery1x Memmert universal oven UN110mFactory calibration certificate (calibration at 160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The UN110m is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceMemmert offers options, accessories and services for the UN110m, such as additional grid shelves or a different voltage variant. For individual advice on your requirements, please contact us. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

The Memmert universal oven UF110mplus is a Class I medical device under Regulation (EU) 2017/745 with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy. With 108 litres of internal volume and an internal width of 560 mm, it is larger than the UF75mplus with 74 litres, and two grid shelves are included as standard.TwinDISPLAY, sensors and HeatBALANCETwo Pt100 sensors of DIN class A monitor each other in 4-wire measurement and automatically take over the function of the other in the event of a fault. The setting accuracy is 0.1 °C up to a setpoint temperature of 99.9 °C and 0.5 °C from 100 °C, and the setting temperature range extends from +20 to +300 °C. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays, and the HeatBALANCE function allows fine adjustment of the heating power distribution from -50 to +50 % between the upper and lower heating group. Programming and documentation are done via the Ethernet interface or USB port with the AtmoCONTROL software, and the digital countdown timer can be set from 1 minute to 99 days.Safety for everyday practiceA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum cabinet temperature, and an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can also be selected on the display. The additional AutoSAFETY monitoring automatically follows the setpoint at a freely selectable distance and triggers a visual and audible alarm in the event of deviation. A self-diagnosis system helps with fault finding, and three freely selectable temperature values can be calibrated.Loading, connection and dimensions2 electropolished stainless steel grid shelves are included as standard, and up to 5 shelves are possible. The permissible total load is 175 kg at 20 kg per shelf. The UF110mplus is connected at 230 V with approx. 2,800 W or at 115 V with approx. 1,800 W, in each case 50/60 Hz. The internal dimensions are 560 x 560 x 480 mm and the external dimensions 745 x 864 x 584 mm, with a net weight of around 74 kg.Distinction: physiotherapy unit and laboratory oven UF110plusThe laboratory unit of the same size is the Memmert universal oven UF110plus with 108 litres and TwinDISPLAY, designed for drying and tempering in laboratories and industry and without a medical intended purpose. In the same size and with the same intended purpose, the Class I medical device available is the UF110m in the SingleDISPLAY version with one Pt100 sensor. The UF110mplus, by contrast, has the TwinDISPLAY and two Pt100 sensors that monitor each other, plus the adjustable temperature monitor or adjustable temperature limiter selectable on the display and AutoSAFETY, as well as the HeatBALANCE function.Selection guide: when the neighbouring size is a better fitThe next smaller UF75mplus has 74 litres and a 120 kg total load, but with up to six shelves it takes one shelf more than the UF110mplus. More volume and more shelves are offered by the Memmert universal oven UF160mplus with 161 litres, up to eight shelves and a 210 kg total load. The UF110mplus sits in between with 108 litres and a 175 kg total load.Typical applicationsAs a Class I medical device, the Memmert universal oven UF110mplus is intended exclusively for physiotherapeutic applications with fango, silicate and APS packs.Heating of fango packs for physiotherapeutic useHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsSetting temperature range+20 to +300 °CWorking temperature rangemin. 10 °C above room temperature to 300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, redundantInternal volume108 lInternal dimensions (W x H x D)560 x 560 x 480 mm (depth minus 39 mm for the fan)External dimensions of housing (W x H x D)745 x 864 x 584 mmNet weightapprox. 74 kgConnection230 V, 50/60 Hz, approx. 2,800 W; 115 V, 50/60 Hz, approx. 1,800 WShelves included in scope of delivery2Maximum number of shelves5Max. load of unit175 kgMax. load per shelf20 kgControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, AutoSAFETY, visual and audible alarmMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rh, non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe UF110mplus is one of nine sizes in the mplus series from 32 to 1,060 litres, all with TwinDISPLAY and the same setting temperature range of +20 to +300 °C.ModelInternal volumeSetting temperatureDisplayUF30mplus32 l+20 to +300 °CTwinDISPLAYUF55mplus53 l+20 to +300 °CTwinDISPLAYUF75mplus74 l+20 to +300 °CTwinDISPLAYUF110mplus (this page)108 l+20 to +300 °CTwinDISPLAYUF160mplus161 l+20 to +300 °CTwinDISPLAYUF260mplus256 l+20 to +300 °CTwinDISPLAYUF450mplus449 l+20 to +300 °CTwinDISPLAYUF750mplus749 l+20 to +300 °CTwinDISPLAYUF1060mplus1,060 l+20 to +300 °CTwinDISPLAYScope of delivery1x Memmert universal oven UF110mplusFactory calibration certificate (calibration at +160 °C)Fully insulated stainless steel door(s) with 2-point locking (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The UF110mplus is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceFor the UF110mplus, the 115 V voltage variant, extended over-temperature protection and a temperature throttle (factory limit on the maximum adjustable temperature) are available as options, among others. For accessories, we arrange additional grid shelves, perforated trays, drip trays, a wall bracket, a USB-Ethernet adapter or a base frame. For DAkkS calibration, IQ/OQ/PQ documentation and qualification or a maintenance contract, we will gladly arrange the right contact. Get in touch for individual advice on your practice equipment.

With 108 litres of interior, the Memmert universal oven UN110mplus sits between the UN75mplus and the UN160mplus in the UN-mplus series. As a Class I medical device under Regulation (EU) 2017/745, it is used for the heating and keeping warm of fango, silicate and APS packs in physiotherapy, and two stainless steel grid shelves are included as standard.Dimensions, loading and connectionThe interior measures 560 x 560 x 480 mm, and the housing is 864 mm high and 584 mm deep externally, plus 56 mm for the door handle, with a net weight of around 74 kg. Up to five shelves are possible, and the permissible total load is 175 kg at 20 kg per shelf. Connection is at 230 V with approx. 2,800 W or at 115 V with approx. 1,800 W.Sensors and controlTemperature measurement is handled by two redundant Pt100 sensors of DIN class A with 4-wire measurement, and if one sensor fails, measurement continues via the remaining one. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays, and the setting accuracy is 0.1 °C up to 99.9 °C setpoint temperature and 0.5 °C above that. With HeatBALANCE, the heating power distribution between the upper and lower heating group can be shifted by -50 to +50 %.Safety and communicationA mechanical temperature limiter of protection class 1 according to DIN 12880 switches off the heating at around 20 °C above the maximum permissible cabinet temperature, and an adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can also be selected. AutoSAFETY monitors the setpoint at a freely selectable distance and triggers a visual and audible alarm if it is exceeded or not reached. Via the Ethernet interface or USB port, programs can be programmed, managed and transferred using the AtmoCONTROL software.Distinction from the laboratory oven and the SingleDISPLAY versionThe laboratory version without a medical intended purpose in the same size is the Memmert universal oven UN110plus with TwinDISPLAY. As a Class I medical device with one sensor and SingleDISPLAY, the UN110m is also available, and the intended purpose remains the same.Selection guide: the right sizeIf 74 litres are sufficient, the UN75mplus with six shelves and a 120 kg total load is the smaller alternative. If more volume is needed, the Memmert universal oven UN160mplus offers 161 litres, eight shelves and a 210 kg total load.Typical applicationsAs a Class I medical device, the UN110mplus is intended exclusively for the heating and keeping warm of fango, silicate and APS packs in physiotherapy.Heating and keeping warm of fango packs in physiotherapyHeating and keeping warm of silicate packsHeating and keeping warm of APS packsTechnical detailsAdjustable temperature range+20 to +300 °CWorking temperature rangemin. 5 °C above room temperature to +300 °CTemperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °CTemperature sensor2x Pt100, DIN class A, 4-wire measurement, mutual monitoringInternal volume108 lInternal dimensions (W x H x D)560 x 560 x 480 mmExternal dimensions of housing (H x D)864 x 584 mmNet weightapprox. 74 kgGross weight (shipping carton)approx. 99 kgConnection230 V, 50/60 Hz, approx. 2,800 W; 115 V, 50/60 Hz, approx. 1,800 WShelves included in scope of delivery2Maximum number of shelves5Max. load of unit175 kgMax. load per shelf20 kgPackaging dimensions (W x H x D)830 x 1,050 x 800 mmControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic displayAdditional functionsHeatBALANCE, AutoSAFETY, visual and audible alarmMedical device classificationClass I under Regulation (EU) 2017/745Intended purposeHeating/keeping warm of fango, silicate and APS packs in physiotherapyPermissible ambient temperature5 °C to 40 °CPermissible humiditymax. 80 % rel., non-condensingMarkingsCE, VDE, ULOther sizes in the seriesThe UN-mplus series ranges from 32 to 749 litres across eight sizes, each with TwinDISPLAY, natural convection and a setting temperature range of +20 to +300 °C. The same size is also available with SingleDISPLAY and one sensor as the UN110m.ModelInternal volumeSetting temperatureDisplayUN30mplus32 l+20 to +300 °CTwinDISPLAYUN55mplus53 l+20 to +300 °CTwinDISPLAYUN75mplus74 l+20 to +300 °CTwinDISPLAYUN110mplus (this page)108 l+20 to +300 °CTwinDISPLAYUN160mplus161 l+20 to +300 °CTwinDISPLAYUN260mplus256 l+20 to +300 °CTwinDISPLAYUN450mplus449 l+20 to +300 °CTwinDISPLAYUN750mplus749 l+20 to +300 °CTwinDISPLAYScope of delivery1x Memmert universal oven UN110mplusFactory calibration certificate (calibration at +160 °C)Fully insulated stainless steel door with 2-point locking (compression door lock)2x stainless steel grid shelves, electropolishedRegulatory informationThe unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The unit is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of heating and keeping warm fango, silicate and APS packs in physiotherapy.Installation in a wall openingFor fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.Individual requirements and procurement serviceWe arrange options, accessories and services for the UN110mplus individually with you, for example for calibration or qualification documents. Please contact us for a suitable quotation. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.