Skip to main content Skip to search Skip to main navigation

Memmert universal oven UF260plus, 256 l, +20 to +300 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert universal oven UF260plus, 256 l, +20 to +300 °C, TwinDISPLAY"

With 256 litres of internal volume and up to nine shelves, the Memmert universal oven UF260plus offers considerably more space than the small models of the series, with external dimensions of 824 x 1,183 x 684 mm. Two Pt100 sensors monitor each other, and HeatBALANCE can be used to distribute the heating power between the upper and lower heating group.

Interior for larger batches

The interior measures 640 x 800 x 500 mm and holds up to nine shelves, and the housing measures 824 x 1,183 x 684 mm externally. Two electropolished stainless steel grid shelves are part of the standard equipment, and a total load of up to 300 kg at a maximum of 20 kg per shelf is permitted. The electronically controllable air turbine adjusts the circulation in 10 % steps, and an electronically adjustable exhaust air flap admits preheated fresh air.

Heating power distribution with HeatBALANCE

With HeatBALANCE, the heating power distribution between the upper and lower heating group can be adjusted from -50 to +50 %. Two Pt100 sensors of DIN class A in 4-wire measurement monitor each other and take over the function of the other in case of failure. Control is via the ControlCOCKPIT TwinDISPLAY with two TFT colour graphic displays. Programs are managed via Ethernet or USB using AtmoCONTROL, and the setting accuracy is 0.1 °C up to a set temperature of 99.9 °C and 0.5 °C from 100 °C.

Safety reserves for larger batches

A mechanical temperature limiter of protection class 1 according to DIN 12880 forms the first level and switches off at about 20 °C above the maximum oven temperature. An adjustable temperature monitor of protection class 3.1 or an adjustable temperature limiter of protection class 2 can also be selected. AutoSAFETY runs in parallel, follows the set point at a freely selectable offset and raises a visual and audible alarm in case of deviation. An ambient temperature of +5 °C to +40 °C at a maximum of 80 % relative humidity is permissible.

Choosing the right size

If batches become larger, the UF450plus with 449 litres offers more internal volume, see the size table below. If floor space is limited, the smaller UF160plus with 161 litres and likewise TwinDISPLAY is the obvious alternative.

Typical applications

With 256 litres of internal volume, the UF260plus is suitable for drying, heating, tempering, ageing, baking, testing and curing in research, science, industry and quality assurance.

  • Drying and tempering larger series of samples with several shelves at the same time
  • Curing and baking with redundant temperature measurement
  • Ageing and testing of components in industry
  • Testing in quality assurance

Technical details

Setting temperature range+20 to +300 °C
Working temperature rangemin. 10 °C above room temperature to +300 °C
Temperature setting accuracyup to 99.9 °C: 0.1 °C, from 100 °C: 0.5 °C
Temperature sensor2x Pt100, DIN class A, 4-wire measurement, redundant
Internal volume256 l
Internal dimensions (W x H x D)640 x 800 x 500 mm (depth minus 39 mm for the fan)
External dimensions of housing (W x H x D)824 x 1,183 x 684 mm
Net weightapprox. 110 kg
Connection 230 V50/60 Hz, approx. 3,400 W
Connection 115 V50/60 Hz, approx. 1,800 W
Maximum number of shelves9
Shelves in the scope of delivery2
Max. load of unit300 kg
Max. load per shelf20 kg
Interiordeep-drawn ribbed, 4-sided all-round heating
ControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic display
Additional functionsHeatBALANCE, AutoSAFETY, visual and audible alarm
Permissible ambient temperature+5 °C to +40 °C
Permissible humiditymax. 80 % rel., non-condensing
Maximum installation altitude2,000 m
MarkingsCE, VDE GS, UL, EAC

Other sizes in the series

The UF-plus series comprises nine sizes from 32 to 1,060 litres, sorted below by internal volume:

ModelInternal volumeSetting temperatureDisplay
UF30plus32 l+20 to +300 °CTwinDISPLAY
UF55plus53 l+20 to +300 °CTwinDISPLAY
UF75plus74 l+20 to +300 °CTwinDISPLAY
UF110plus108 l+20 to +300 °CTwinDISPLAY
UF160plus161 l+20 to +300 °CTwinDISPLAY
UF260plus (this page)256 l+20 to +300 °CTwinDISPLAY
UF450plus449 l+20 to +300 °CTwinDISPLAY
UF750plus749 l+20 to +300 °CTwinDISPLAY
UF1060plus1,060 l+20 to +300 °CTwinDISPLAY

For applications that do not require redundant sensors, the same volume is available as a single-sensor version in the UF series: UF260.

Scope of delivery

  • 1x Memmert universal oven UF260plus
  • Factory calibration certificate (calibration at +160 °C)
  • Fully insulated stainless steel door with 2-point locking (compression door lock)
  • 2x stainless steel grid shelf, electropolished

Regulatory information

The unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal.

Installation in a wall opening

For fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29738) or without air slots (B29739). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.

Individual requirements and procurement service

For the UF260plus, the following can be ordered from the factory, among others: a full-view glass door, interior lighting and socket, a programmable door lock and door-open detection. Suitable accessories include additional shelves and perforated trays, drip trays, a wall bracket, a USB-Ethernet adapter and AtmoCONTROL software licences. For qualification and maintenance, we arrange calibration, IQ/OQ/PQ and maintenance services. For individual requirements, we will advise you personally.

Certification marks: GS (VDE)
Volume: 256 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E28891 for sizes 260 and 410
Manufacturer number: E28891

The E28891 stainless steel grid is an electropolished shelf for 26 Memmert models in sizes 260 and 410. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example UN260 or IF260.All 26 models have 2 grids as standard. The maximum number is 9 grids (size 260) and 14 grids (size 410). According to Memmert, the load per shelf is 20 kg. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Drying several sample series in parallel in routine operation, for example in the UF260Incubating extensive sample series in research and medicine, for example in the IF260Parallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoMicrobiological examinations and microbial count determination in the routine laboratory, for example in the IPP410ecoSuitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)UN260plus2920256UN2602920256IF260plus2920256IN260plus2920256IF2602920256IN2602920256UF2602920256UF260plus2920256IF260bw2920256IPP260eco2920256IPP260ecoPlus2920256IPP410eco21420384IPP410ecoplus21420384HPP260eco2920256HPP410eco21420384ICH2602920256ICP2602920256IN260m2920256IN260mplus2920256IF260m2920256IF260mplus2920256UN260m2920256UN260mplus2920256UF260m2920256UF260mplus2920256UF260TS2920256The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel grid, electropolished (E28891)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €126.42
memmert rohrverlaengerung gerade
Memmert straight slip-on pipe extension B29718 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29718

The straight slip-on pipe extension B29718 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The angled version is also available (B29719). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorTempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Drying and tempering of large, heavy components in industrial manufacturing, for example in the UF1060Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 straight slip-on pipe extensionIndividual requirements & procurement serviceFor the angled version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €41.28
memmert rohrverlaengerung gewinkelt
Memmert angled slip-on pipe extension B29719 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29719

The angled slip-on pipe extension B29719 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The straight version is also available (B29718). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Parallel drying of several sample batches in a confined space, for example in the UN75Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material samples in series, for example in the UN260Testing and curing of larger components in quality assurance, for example in the UF750Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 angled slip-on pipe extensionIndividual requirements & procurement serviceFor the straight version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €108.36
Memmert levelling feet B29768, set of 4, for sizes 30, 55, 75, 110, 160 and 260
Manufacturer number: B29768

The B29768 set of levelling feet contains 4 pieces. With levelling feet, the unit can be aligned horizontally.The set is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco and HPPeco series in sizes 30, 55, 75, 110, 160 and 260. The table of compatible models shows which series is available in which size. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorEmbedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenParallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoSuitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574UN160pa160161IF30plus3032IN30plus3032IF303032IN303032IF160160161IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UN55pa5553UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032IPP260eco260256IPP260ecoPlus260256HPP110eco110108HPP260eco260256IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF160TS160161UF260TS260256Scope of delivery1 set of levelling feet (4 pieces)Individual requirements & procurement serviceFor base frames, further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €46.44
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B29726 for sizes 260 and 410
Manufacturer number: B29726

The stainless steel slide-in drip tray B29726 is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 260 and 410. It has a 15 mm rim and collects dripping liquid. Memmert states a maximum load of 4 kg per slide-in drip tray. The size corresponds to the number in the unit name, for example UN260 or IF260.According to Memmert, it can impair the spatial temperature distribution. The table of compatible models shows which series is available in which size. The base drip tray for the same unit size is also available (B29722). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Forcing tests for beer stability, for example in the IPP410ecoShelf-life tests on dairy products, for example in the IPP410ecoSuitable forModelSizeInterior volume (l)UN260plus260256UN260260256IF260plus260256IN260plus260256IF260260256IN260260256UF260260256UF260plus260256IPP260eco260256IPP260ecoPlus260256IPP410eco410384IPP410ecoplus410384HPP260eco260256HPP410eco410384ICH260260256ICP260260256IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF260TS260256Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert4 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €164.26
Memmert levelling base frame B33664, height 130 mm, for size 260
Manufacturer number: B33664

The levelling base frame B33664, with a height of 130 mm, is the flat version for Memmert units in the U, Um, I, Im, IPPeco, HPPeco and IFbw series in size 260. It fits 20 models of this size. The size corresponds to the number in the unit name, for example UN260 or IF260.The base frame B29751 with a height of 500 mm is also available for this size.Typical applicationsUnits of size 260 are placed on the base frame. Typical uses of these units:Curing and baking with redundant temperature measurement, for example in the UF260plusIncubating and tempering larger sample series with several shelves at the same time, for example in the IF260plusMaterial tests and quality assurance with high sample throughput, for example in the UN260Cultivation of samples and cultures down to at least 20 °C below room temperature, for example in the IPP260ecoplusSuitable forModelSizeInterior volume (l)UN260plus260256UN260260256IF260plus260256IN260plus260256IF260260256IN260260256UF260260256UF260plus260256IF260bw260256IPP260eco260256IPP260ecoPlus260256HPP260eco260256IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN260m260256UN260mplus260256UF260m260256UF260mplus260256Technical detailsHeight130 mmScope of delivery1 levelling base frame, height 130 mmIndividual requirements & procurement serviceFor the taller version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €303.58
memmert boden abtropfschale
Memmert stainless steel base drip tray B29722 for sizes 260 and 410
Manufacturer number: B29722

B29722 is a stainless steel base drip tray with a 15 mm rim for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 260 and 410. It collects dripping liquid. According to Memmert, the maximum load is 4 kg per base drip tray. The size corresponds to the number in the unit name, for example UN260 or IF260.Memmert points out that it can impair the spatial temperature distribution. The table of compatible models shows which series is available in which size. The slide-in drip tray for the same unit size is also available (B29726). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Forcing tests for beer stability, for example in the IPP410ecoShelf-life tests on dairy products, for example in the IPP410ecoSuitable forModelSizeInterior volume (l)UN260plus260256UN260260256IF260plus260256IN260plus260256IF260260256IN260260256UF260260256UF260plus260256IPP260eco260256IPP260ecoPlus260256IPP410eco410384IPP410ecoplus410384HPP260eco260256HPP410eco410384ICH260260256ICP260260256IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF260TS260256Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert4 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €209.84
memmert untergestell nivellierbar
Memmert levelling base frame B29751, height 500 mm, for size 260
Manufacturer number: B29751

The levelling base frame B29751 has a height of 500 mm and is intended for Memmert units in the U, Um, I, Im, IPPeco, HPPeco and IFbw series in size 260. It fits 20 models of size 260. The size corresponds to the number in the unit name, for example UN260 or IF260.A flat base frame with a height of 130 mm is also available (B33664). The image is for illustration only.Typical applicationsUnits of size 260 are placed on the base frame. Typical uses of these units:Drying several sample series in parallel in routine operation, for example in the UF260Incubating extensive sample series in research and medicine, for example in the IF260Parallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoHeat treatment and drying of larger material batches in industry, for example in the UN260Suitable forModelSizeInterior volume (l)UN260plus260256UN260260256IF260plus260256IN260plus260256IF260260256IN260260256UF260260256UF260plus260256IF260bw260256IPP260eco260256IPP260ecoPlus260256HPP260eco260256IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN260m260256UN260mplus260256UF260m260256UF260mplus260256Technical detailsHeight500 mmScope of delivery1 levelling base frame, height 500 mmIndividual requirements & procurement serviceFor the flat version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €389.58
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68510 for sizes 260 and 410
Manufacturer number: B68510

The B68510 stainless steel perforated tray is intended for Memmert units in the U, Um, UF TS, I, Im, IPPeco, ICP, ICH, HPPeco and IFbw series in sizes 260 and 410. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example UN260 or IF260. The image is for illustration only.According to Memmert, the maximum load per shelf for these sizes is 20 kg. In addition, the maximum load per unit limits the loading; it is stated in the unit’s data sheet. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying several sample series in parallel in routine operation, for example in the UF260Incubating extensive sample series in research and medicine, for example in the IF260Parallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoMicrobiological examinations and microbial count determination in the routine laboratory, for example in the IPP410ecoSuitable forModelSizeInterior volume (l)UN260plus260256UN260260256IF260plus260256IN260plus260256IF260260256IN260260256UF260260256UF260plus260256IF260bw260256IPP260eco260256IPP260ecoPlus260256IPP410eco410384IPP410ecoplus410384HPP260eco260256HPP410eco410384ICH260260256ICP260260256IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF260TS260256Technical detailsMaterialStainless steelLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €206.40
Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert reinforced stainless steel grid E29766 for sizes 260 and 410
Manufacturer number: E29766

The reinforced stainless steel grid E29766 is electropolished and, according to Memmert, can bear up to 60 kg. According to Memmert, the standard grids carry 20 kg per shelf in these sizes. The grid is a shelf level in the interior. It is intended for Memmert units in the U, Um, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 260 and 410. The size corresponds to the number in the unit name, for example UN260 or IF260.Please note the maximum load per unit, as it limits the total load of all shelves. The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Heat treatment and drying of larger material batches in industry, for example in the UN260Material tests and quality assurance with high sample throughput, for example in the UN260Materials and material testing with higher sample throughput in industry, for example in the HPP410ecoSuitable forModelSizeInterior volume (l)UN260plus260256UN260260256IF260plus260256IN260plus260256IF260260256IN260260256UF260260256UF260plus260256IPP260eco260256IPP260ecoPlus260256IPP410eco410384IPP410ecoplus410384HPP260eco260256HPP410eco410384ICH260260256ICP260260256IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN260m260256UN260mplus260256UF260m260256UF260mplus260256Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmertup to 60 kgScope of delivery1 reinforced stainless steel grid, electropolishedIndividual requirements & procurement serviceFor standard grids, perforated trays and drip trays of the same size, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €347.44