Skip to main content Skip to search Skip to main navigation

Memmert incubator IN30mplus, 32 l, +20 to +80 °C, TwinDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert incubator IN30mplus, 32 l, +20 to +80 °C, TwinDISPLAY"

32 litres interior, 704 mm housing height: the Memmert incubator IN30mplus is the smallest size in the IN-mplus series. As a Class I medical device according to Regulation (EU) 2017/745, it is used to temper irrigation and infusion solutions and contrast media. One electropolished stainless steel grid shelf is supplied as standard, and up to three shelves are possible.

Display and sensors

The ControlCOCKPIT TwinDISPLAY, an adaptive digital PID microprocessor controller with two TFT colour graphic displays, handles the control. Two Pt100 sensors of DIN class A measure in 4-wire technology and check each other: if one sensor fails, the second takes over automatically. The set temperature can be adjusted between +20 and +80 °C, and the setting accuracy is 0.1 °C. The working temperature range starts at least 5 °C above room temperature.

Safety

A mechanical temperature limiter of protection class 1 (DIN 12880) disconnects the heating from the mains at about 20 °C above the maximum chamber temperature. Optionally, an adjustable temperature monitor (protection class 3.1) or an adjustable temperature limiter (protection class 2) can be activated on the display. The AutoSAFETY function follows the set point at a freely selectable offset, warns visually and audibly in case of deviations and switches off the heating if the set point is exceeded; a self-diagnosis system helps with fault finding. A program of 4 hours at 160 °C is permanently stored for sterilising the interior, not for sterilising load items.

Functions and connectivity

  • HeatBALANCE: heating power distribution of upper/lower heating group adjustable from -50 to +50 %
  • SetpointWAIT: process time starts only after the set temperature has been reached
  • Calibration function for three freely selectable temperature values
  • Ethernet interface and USB port for programs with the AtmoCONTROL software
  • Program sequence saved in the event of a power failure

Interior, ventilation and connection

The stainless steel interior is easy to clean, stiffened by deep-drawn ribbing and heated on all four sides. The housing is made of textured stainless steel with a fully galvanised rear wall. With natural ventilation, preheated fresh air flows in, and the exhaust air volume is controlled by an electronically adjustable throttle valve on the exhaust air outlet. The internal dimensions are 400 x 320 x 250 mm and the external dimensions 585 x 704 x 434 mm (plus 56 mm door handle), and the net weight is around 48 kg. A total load of 60 kg is permitted at a maximum of 20 kg per shelf. The mains connection is 230 V (approx. 1,600 W), and in the 115 V version approx. 800 W, in each case 50/60 Hz.

The IN30m in comparison

Same size, but with a different intended purpose: the IN30m is likewise a Class I medical device, but is used for warming and keeping warm fango, silicate and APS packs in physiotherapy. It has only one SingleDISPLAY and a single Pt100 sensor, without the second display and the redundant sensor pairing of the IN30mplus.

Choosing the right size

If more capacity is needed, the next size up follows, the Memmert incubator IN55mplus with 53 litres, up to four shelves and 80 kg permissible total load. With 32 litres and a maximum of three shelves, the IN30mplus remains the most compact model in the series.

Typical applications

As a Class I medical device, the IN30mplus is intended for warming irrigation and infusion solutions and contrast media.

  • Warming irrigation solutions
  • Warming infusion solutions
  • Warming contrast media

Technical details

Setting temperature range+20 to +80 °C
Working temperature rangemin. 5 °C above room temperature to +80 °C
Temperature setting accuracy0.1 °C
Temperature sensor2x Pt100, DIN class A, 4-wire measurement, redundant
Internal volume32 l
Internal dimensions (W x H x D)400 x 320 x 250 mm
External dimensions of housing (W x H x D)585 x 704 x 434 mm (plus 56 mm door handle)
Net weightapprox. 48 kg
Connection230 V, 50/60 Hz, approx. 1,600 W; 115 V, 50/60 Hz, approx. 800 W
Shelves in the scope of delivery1
Maximum number of shelves3
Max. load of unit60 kg
Max. load per shelf20 kg
ControlControlCOCKPIT TwinDISPLAY, PID microprocessor controller, 2x TFT colour graphic display
Additional functionsHeatBALANCE, SetpointWAIT, AutoSAFETY, visual and audible alarm
Medical device classificationClass I according to Regulation (EU) 2017/745
Intended purposeWarming irrigation and infusion solutions and contrast media
Permissible ambient temperature5 °C to 40 °C
Permissible humiditymax. 80 % rh, non-condensing
Shipping carton (W x H x D)660 x 890 x 650 mm
MarkingsCE, VDE, UL

Other sizes in the series

The IN30mplus is one of eight sizes in the IN-mplus series from 32 to 749 litres, all with TwinDISPLAY and the same setting temperature range of +20 to +80 °C.

ModelInternal volumeSetting temperatureDisplay
IN30mplus (this page)32 l+20 to +80 °CTwinDISPLAY
IN55mplus53 l+20 to +80 °CTwinDISPLAY
IN75mplus74 l+20 to +80 °CTwinDISPLAY
IN110mplus108 l+20 to +80 °CTwinDISPLAY
IN160mplus161 l+20 to +80 °CTwinDISPLAY
IN260mplus256 l+20 to +80 °CTwinDISPLAY
IN450mplus449 l+20 to +80 °CTwinDISPLAY
IN750mplus749 l+20 to +80 °CTwinDISPLAY

Scope of delivery

  • Factory calibration certificate (calibration at +37 °C)
  • Fully insulated stainless steel door with 2-point locking (compression door lock), inner glass door
  • 1x stainless steel grid shelf, electropolished

Regulatory information

The unit is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Information on returning old appliances is available on our page Environment and disposal. The IN30mplus is also classified as a Class I medical device according to Regulation (EU) 2017/745, with the intended purpose of warming irrigation and infusion solutions and contrast media.

Individual requirements and procurement service

For the IN30mplus, Memmert offers options, accessories and services, and options are specified at the factory when ordering. We clarify your individual requirements, from the suitable option to additional accessories, and organise the procurement. Get in touch for non-binding advice. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

Volume: 32 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E28884 for size 30
Manufacturer number: E28884

The E28884 stainless steel grid is an electropolished shelf for 19 Memmert models in size 30. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table.All 19 models have 1 grid as standard and can hold up to 3 grids. According to Memmert, the load per shelf is 20 kg. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Tempering and curing of individual material samples, for example in the UF30Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorSuitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)UF30132032UN30132032UF30plus132032UN30plus132032IF30plus132032IN30plus132032IF30132032IN30132032UN30pa132032IPP30132032IPP30plus132032IN30m132032IN30mplus132032IF30m132032IF30mplus132032UN30m132032UN30mplus132032UF30m132032UF30mplus132032The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel grid, electropolished (E28884)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €55.04
memmert rohrverlaengerung gerade
Memmert straight slip-on pipe extension B29718 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29718

The straight slip-on pipe extension B29718 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The angled version is also available (B29719). The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorTempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Drying and tempering of large, heavy components in industrial manufacturing, for example in the UF1060Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 straight slip-on pipe extensionIndividual requirements & procurement serviceFor the angled version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €41.28
memmert rohrverlaengerung gewinkelt
Memmert angled slip-on pipe extension B29719 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29719

The angled slip-on pipe extension B29719 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The straight version is also available (B29718). The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Parallel drying of several sample batches in a confined space, for example in the UN75Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material samples in series, for example in the UN260Testing and curing of larger components in quality assurance, for example in the UF750Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 angled slip-on pipe extensionIndividual requirements & procurement serviceFor the straight version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €108.36
memmert untergestell nivellierbar
Memmert levelling base frame B29745, height 600 mm, for size 30
Manufacturer number: B29745

The levelling base frame B29745 has a height of 600 mm and is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30.A flat base frame with a height of 130 mm is also available (B33657). The mobile version with a height of 660 mm is also available (B29746). The image is for illustration only.Typical applicationsUnits of size 30 are placed on the base frame. Typical uses of these units:Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorDrying and heating in industrial quality assurance, for example in the UN30plusMicrobiological cooled incubation in the IPP30 Peltier cooling incubatorSample preparation in pathology and histology in the UN30pa paraffin ovenWhen installing, the clearances of the unit apply; for the UN30 universal oven, at least 15 cm wall clearance, 20 cm ceiling clearance and 5 cm side clearance.Suitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsHeight600 mmScope of delivery1 levelling base frame, height 600 mmIndividual requirements & procurement serviceFor the flat and the mobile version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €266.60
Memmert levelling feet B29768, set of 4, for sizes 30, 55, 75, 110, 160 and 260
Manufacturer number: B29768

The B29768 set of levelling feet contains 4 pieces. With levelling feet, the unit can be aligned horizontally.The set is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco and HPPeco series in sizes 30, 55, 75, 110, 160 and 260. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorEmbedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenParallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoSuitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574UN160pa160161IF30plus3032IN30plus3032IF303032IN303032IF160160161IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UN55pa5553UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032IPP260eco260256IPP260ecoPlus260256HPP110eco110108HPP260eco260256IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF160TS160161UF260TS260256Scope of delivery1 set of levelling feet (4 pieces)Individual requirements & procurement serviceFor base frames, further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €46.44
Memmert stacking kit B29744 for sizes 30, 50, 55, 75, 105 and 110
Manufacturer number: B29744

The B29744 stacking kit consists of 4 pieces and is intended for stacking units of the same size. It is intended for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco, HCP and IFbw series in sizes 30, 50, 55, 75, 105 and 110.Separate stacking kits are also available for HCP150, HCP240 and for ICO50, 180 and 240 (B42114, B48129, B68362 and B64732). The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorIncubating several sample series at the same time in research and medicine, for example in the IF110Environmental tests and environmental simulations in the HCP105 humidity chamberSuitable forModelSizeInterior volume (l)IF110bw110108UF303032IF110110108UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574IF30plus3032IN30plus3032IF303032IN303032IF55plus5553IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574UN55pa5553UF110plus110108UN110110108UN110plus110108IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032HPP110eco110108HCP505056HCP105105107IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108Scope of delivery1 stacking kit (4 pieces)Individual requirements & procurement serviceFor the stacking kits for HCP humidity chambers and ICO CO₂ incubators, for base frames and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €61.92
Memmert stainless steel perforated tray B68506 for size 30
Manufacturer number: B68506

The B68506 stainless steel perforated tray is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. It is a shelf and therefore one shelf level in the interior.According to Memmert, the maximum load per shelf for this size is 20 kg. In addition, the maximum load per unit limits the loading; it is stated in the unit’s data sheet.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Tempering and curing of individual material samples, for example in the UF30Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsMaterialStainless steelLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €103.20
memmert untergestell fahrbar
Memmert mobile base frame B29746, height 660 mm, for size 30
Manufacturer number: B29746

The mobile base frame B29746 is 660 mm high.It is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. The levelling version with a height of 600 mm is also available (B29745), as is a flat base frame with a height of 130 mm (B33657). The image is for illustration only.Typical applicationsUnits of size 30 are placed on the base frame. Typical uses of these units:Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorDrying and heating in industrial quality assurance, for example in the UN30plusMicrobiological cooled incubation in the IPP30 Peltier cooling incubatorSample preparation in pathology and histology in the UN30pa paraffin ovenWhen installing, the clearances of the unit apply; for the UN30 universal oven, at least 15 cm wall clearance, 20 cm ceiling clearance and 5 cm side clearance.Suitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsHeight660 mmScope of delivery1 mobile base frame, height 660 mmIndividual requirements & procurement serviceFor the flat and the levelling version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €389.58
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02070 for size 30
Manufacturer number: B02070

The B02070 slide-in drip tray is made of stainless steel and has a 15 mm rim. It is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30 and collects dripping liquid. According to Memmert, the maximum load per slide-in drip tray for this size is 1.5 kg.In addition, according to Memmert, it can impair the spatial temperature distribution. The base drip tray for the same unit size is also available (B04356). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying smaller sample quantities and laboratory glassware on the laboratory bench, for example in the UN30Embedding and heating paraffin or other embedding media for histology, for example in the UN30pa paraffin ovenSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert1.5 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €67.94
memmert boden abtropfschale
Memmert stainless steel base drip tray B04356 for size 30
Manufacturer number: B04356

The stainless steel base drip tray B04356 is intended for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. It has a 15 mm rim and collects dripping liquid. Memmert states a maximum load of 1.5 kg per base drip tray.According to Memmert, it can impair the spatial temperature distribution. The slide-in drip tray for the same unit size is also available (B02070). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying smaller sample quantities and laboratory glassware on the laboratory bench, for example in the UN30Embedding and heating paraffin or other embedding media for histology, for example in the UN30pa paraffin ovenSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsMaterialStainless steelRim15 mmMaximum load according to Memmert1.5 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €103.20
Memmert levelling base frame B33657, height 130 mm, for size 30
Manufacturer number: B33657

The levelling base frame B33657, with a height of 130 mm, is the flat version for Memmert units in the U, Um, UNpa, I, Im and IPPeco series in size 30. It fits 19 models of this size.The base frame B29745 with a height of 600 mm is also available for this size.Typical applicationsUnits of size 30 are placed on the base frame. Typical uses of these units:Incubating culture media and cultures in routine microbiology, for example in the IN30 incubatorDrying and heating in industrial quality assurance, for example in the UN30plusMicrobiological cooled incubation in the IPP30 Peltier cooling incubatorSample preparation in pathology and histology in the UN30pa paraffin ovenSuitable forModelSizeInterior volume (l)UF303032UN303032UF30plus3032UN30plus3032IF30plus3032IN30plus3032IF303032IN303032UN30pa3032IPP303032IPP30plus3032IN30m3032IN30mplus3032IF30m3032IF30mplus3032UN30m3032UN30mplus3032UF30m3032UF30mplus3032Technical detailsHeight130 mmScope of delivery1 levelling base frame, height 130 mmIndividual requirements & procurement serviceFor the taller version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €208.98