IKA T 65 digital ULTRA-TURRAX disperser, 2 to 50 l, up to 9,500 rpm, 0004234500

The S 65 C - G 65 G (0010001665) is the dispersing tool for large batches on the T 65: it processes volumes of 2 to 50 l using a 65 mm stator. The installation length is 520 mm, and the tool weighs 4.09 kg. The parts in contact with the product are made of AISI 316L and ceramic.Ball bearings and ceramic plain bearingsThe unit is supported by ball bearings and ceramic plain bearings. The tool is suitable for use with solvents; the pH range is from 2 to 13. The maximum operating temperature is 170 °C. It can be sterilised using all methods, with the exception of the ball bearings. The tool is not suitable for use under vacuum.Geometry and finenessThe rotor draws in the medium and forces it radially through the stator slots. The rotor has a diameter of 53 mm; the gap to the stator measures 0.5 mm. At the maximum permissible speed of 9,500 rpm, the peripheral speed reaches 26.4 m/s. The immersion depth ranges from 90 to 450 mm. The final fineness is 25 to 75 µm for suspensions and 5 to 25 µm for emulsions.Ceramic or carbideIf a vacuum is required, the S 65 KG - HH - G 65 G is the appropriate choice. It features a carbide mechanical seal and operates at pressures ranging from 1 mbar to 6 bar. The final fineness values are the same for both tools. Another variant in the S-65-C series, featuring AISI 316L and ceramic, is the S 65 C - G 65 M, which processes volumes of 2 to 40 l.Typical applicationsDispersing and emulsifying volumes from 2 to 50 lSolvent-based batchesProcesses up to 170 °C for short periodsMedia compatible with contact with ceramic and AISI 316LTechnical detailsWorking range (H2O)2 to 50 lStator diameter65 mmRotor diameter53 mmStator/rotor air gap0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed26.4 m/sPenetration depth90 to 450 mmInstallation length520 mmBearings and sealsBall bearings and ceramic plain bearingsMaterials in contact with the productAISI 316L, ceramicpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilityall methods (except ball bearings)Final particle size of suspensions25 to 75 µmFinal particle size of emulsions5 to 25 µmWeight4.09 kgScope of delivery1 x IKA S 65 C - G 65 G dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Individual requirements and procurement serviceIf you require the tool to be supplied together with the appropriate drive unit, do you need a second tool for changing, or guidance on selecting the correct geometry? LT Laborhandel will put together the right combination for your application via its procurement service.

With an installation length of 520 millimetres and a weight of 3.91 kilograms, the IKA S 65 C - G 65 M is a piece of equipment designed for large batches ranging from 2 to 40 l. The stator has a diameter of 65 millimetres and the rotor 58 millimetres.Speed, gap and immersion depthThe gap between the rotor and stator is 0.5 millimetres wide. The maximum permissible speed is 9,500 rpm, resulting in a circumferential speed of 28.8 metres per second. The tool has an immersion depth of 90 to 450 millimetres; IKA recommends 94 to 450 millimetres. IKA specifies a final particle size of 20 to 50 micrometres for suspensions and 5 to 15 micrometres for emulsions.Bearings and MaterialsThe bearing system consists of ball bearings and ceramic plain bearings. The materials in contact with the product are AISI 316L and ceramic. The tool is suitable for solvents and can be used in the pH range of 2 to 13. The maximum operating temperature is 170 degrees Celsius. It is not designed for vacuum operation.DriveThe tool is intended for use with the T 65 basic and T 65 digital dispersers. It may be sterilised using any method (except for the ball bearings).Typical applicationsDispersing and emulsifying in batches of 2 to 40 lEmulsions with a final particle size of 5 to 15 µmSuspensions with a final particle size of 20 to 50 µmImmersion depths of 90 to 450 mmMedia containing solvents at operating temperatures up to 170 °CTechnical detailsStator diameter65 mmRotor diameter58 mmStator/rotor air gap width0.5 mmProcessable volume (H2O)2 to 40 lMaximum permissible speed9,500 rpmMaximum peripheral speed28.8 m/sImmersion depth90 to 450 mmRecommended penetration depth94 to 450 mmInstallation length520 mmBearing typeBall bearings and ceramic plain bearingsMaterial in contact with the productAISI 316L, ceramicpH range2 to 13Suitable for solventsYesSuitable for vacuumNoSterilisabilityall methods (except ball bearings)Max. operating temperature170 °CFinal particle size of suspensions20 to 50 µmFinal fineness of emulsions5 to 15 µmWeight3.91 kgScope of delivery1 x IKA S 65 C - G 65 M dispersing tool (single tool)The drive is not included in the scope of delivery.Additional tools for the T 65With a rotor diameter of 53 millimetres and a working range of 2 to 50 l, LT Laborhandel stocks the S 65 C - G 65 G. The S 65 KG - HH - G 65 G covers the same volume range.Selection guide: a comparisonToolStator / RotorWorking range (H2O)S 65 C, G 65 M (this product)65 / 58 mm2 to 40 lS 65 C, G 65 G65 / 53 mm2 to 50 lS 65 KG, HH, G 65 G65 / 53 mm2 to 50 lIndividual requirements and procurement serviceLT Laborhandel can source the T 65 digital and other tools on request. The procurement service can assist with selection.

In the S 65 C - G 65 F (0010001667), the parts in contact with the product are made of AISI 316L and ceramic. The tool is designed for batch sizes of 2 to 30 l and is operated by the T 65 digital drive.Bearings and limit valuesThe shaft runs in a ball bearing and a ceramic plain bearing. This tool is not designed for use under vacuum. Solvents are permitted; the pH range is from 2 to 13. The maximum operating temperature is 170 °C; sterilisation may be carried out using any method.Geometry and precisionStator 65 mm, rotor 58 mm, gap 0.5 mm. At 9,500 rpm, the rotor circumference reaches 28.8 m/s. The final fineness ranges from 5 to 20 µm for suspensions and 1 to 10 µm for emulsions. The immersion depth is 90 to 450 mm with an installation length of 520 mm. The tool weighs 3.94 kg. The 58 mm rotor achieves a higher peripheral speed than the 53 mm rotor of the S 65 C - G 65 G, at 26.4 m/s.Typical applicationsDispersing and emulsifying 2 to 30 lSuspensions with final particle sizes of 5 to 20 µmEmulsions with final particle sizes of 1 to 10 µmBatches with solvents in the pH range 2 to 13Processes up to 170 °C without vacuum operationTechnical detailsProcessable volume (H2O)2 to 30 lStator diameter65 mmRotor diameter58 mmStator/rotor gap width0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed28.8 m/sPenetration depth90 to 450 mmInstallation length520 mmBearingBall bearings and ceramic plain bearingsMaterials in contact with the productAISI 316L, ceramicpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilityAll methodsSuitable for vacuum sterilisationNoFinal particle size of suspensions5 to 20 µmFinal fineness of emulsions1 to 10 µmWeight3.94 kgScope of delivery1 x IKA S 65 C - G 65 F dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Comparison within the S 65 seriesThe S 65 KD - G 65 F has the same geometry with a PTFE seal and FFKM O-ring: same stator, same rotor, same gap, 2 to 30 l and the same final particle sizes, plus vacuum down to 100 mbar. For applications up to 50 l, the S 65 C - G 65 G also features ceramic components, but with a 53 mm rotor and a particle size range of 25 to 75 µm for suspensions. Fitted with a mechanical seal, capable of a vacuum down to 1 mbar and pressure up to 6 bar, but also featuring a 65 mm stator and a 58 mm rotor, the S 65 KG - HH - G 65 F operates at 2 to 30 l.Individual requirements and procurement serviceLT Laborhandel can source the T 65 digital drive and other equipment on request. The procurement service will put together the right combination for your batch size.

A vacuum down to 1 mbar and a pressure up to 6 bar are among the features that distinguish the S 65 KG - HH - G 65 G (0010010765) from the ceramic tool S 65 C - G 65 G. Both have a 65 mm stator and process 2 to 50 l on the T 65. Here, a single-acting mechanical seal made of carbide against carbide is fitted to the ball-bearing-mounted shaft.Construction and materialsMaterials in contact with the product include FFPM, tungsten carbide (WC) and AISI 316L. The tool is solvent-resistant and FDA-compliant; the pH range is 2 to 13. Operating temperatures of up to 170 °C are permissible for short periods, and it can be sterilised using all methods.DimensionsThe rotor draws in the medium and forces it radially through the stator slots. The rotor has a diameter of 53 mm with a gap width of 0.5 mm; the maximum permissible speed is 9,500 rpm, resulting in a circumferential speed of 26.4 m/s. The installation length is 520 mm, the dimensions are 65 x 560 x 65 mm, and the weight is 4.03 kg. The final particle size is between 25 and 75 µm for suspensions and between 5 and 25 µm for emulsions.Suitable drives and variantsThe tool runs on the T 65 digital. Another geometry is the S 65 C, G 65 M, made from AISI 316L and ceramic, which processes volumes of 2 to 40 l.Typical applicationsDispersing and emulsifying volumes from 2 to 50 lOperating under vacuum down to 1 mbarProcesses at pressures up to 6 barApplications where FDA compliance of the tool is requiredTechnical detailsWorking range (H2O)2 to 50 lStator diameter65 mmRotor diameter53 mmStator/rotor air gap0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed26.4 m/sPenetration depth90 to 450 mmInstallation length520 mmBearing and sealBall bearing, single-acting mechanical seal (carbide/carbide)Materials in contact with the productFFPM, WC / AISI 316LpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilityAll methodsVacuum1 mbarMax. pressure6 barFinal fineness of suspensions25 to 75 µmFinal fineness of emulsions5 to 25 µmFDA complianceYesDimensions (W x H x D)65 x 560 x 65 mmWeight4.03 kgScope of delivery1 x IKA S 65 KG - HH - G 65 G dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Individual requirements and procurement serviceDo you also need the drive unit, a replacement tool or help choosing between the different models? LT Laborhandel sources the components via its procurement service and tailors them to your specific requirements.

The S 65 KG - HH - G 65 M (0010010767) can process up to 40 l in a single batch; the minimum capacity is 2 l. The stator and rotor measure 65 and 58 mm respectively. The shaft is mounted on ball bearings, and the mechanical seal consists of carbide against carbide. IKA specifies the T 65 digital as the drive unit.Position within the S 65 seriesThe S 65 KG - HH - G 65 F has the same rotor, but processes only 2 to 30 l and achieves 5 to 20 µm (suspensions) and 1 to 10 µm (emulsions). The S 65 KG - HH - G 65 G has a smaller rotor (53 mm), processes 2 to 50 l and specifies 25 to 75 µm for suspensions. The unit described here falls between these, with particle sizes of 20 to 50 µm and 5 to 15 µm.Vacuum and pressureThe unit operates under vacuum down to 1 mbar and at pressures up to 6 bar. Materials in contact with the product include FFPM, tungsten carbide (WC) and AISI 316L. It is suitable for solvents; the pH range is from 2 to 13. The maximum operating temperature is 170 °C. Sterilisation is permitted using all methods; FDA compliance is specified.Dimensions and speedThe gap between the rotor and stator is 0.5 mm wide. A speed of 9,500 rpm is permitted, with the rotor circumference reaching up to 28.8 m/s. The immersion depth is 80 to 450 mm, and the installation length is 510 mm. The tool measures 65 x 550 x 65 mm and weighs 4.41 kg.Without vacuumIf a vacuum is not required, the S 65 C, G 65 M is available with the same 2 to 40 l capacity and 58 mm rotor. The parts in contact with the product are made of AISI 316L and ceramic, and it is not suitable for vacuum applications.Typical applicationsDispersing and emulsifying in batches of 2 to 40 lOperations under vacuum down to 1 mbarProcesses at pressures up to 6 barBatches containing solventsApplications where FDA compliance is requiredTechnical detailsWorking range (H2O)2 to 40 lStator diameter65 mmRotor diameter58 mmStator/rotor air gap width0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed28.8 m/sPenetration depth80 to 450 mmInstallation length510 mmBearings and sealsBall bearing, mechanical seal (carbide/carbide)Materials in contact with the productFFPM, WC / AISI 316LpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilityAll methodsVacuum1 mbarMax. pressure6 barFinal fineness of suspensions20 to 50 µmFinal fineness of emulsions5 to 15 µmFDA complianceYesDimensions (W x H x D)65 x 550 x 65 mmWeight4.41 kgScope of delivery1 x IKA S 65 KG - HH - G 65 M dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Individual requirements and procurement serviceLT Laborhandel can source the T 65 digital drive and other tools on request. The procurement service provides assistance in selecting the correct geometry.

The S 65 KG - HH - G 65 F (0010010768), with a 65 mm stator and a 58 mm rotor, processes batches ranging from 2 to 30 l. The shaft is mounted on ball bearings; the mechanical seal consists of carbide against carbide. IKA specifies the T 65 digital as the drive unit.Vacuum and pressureThe unit is designed for vacuum down to 1 mbar and pressure up to 6 bar. Materials in contact with the product include FFPM, tungsten carbide (WC) and AISI 316L. It is suitable for solvents, with a pH range of 2 to 13. The maximum operating temperature is 170 °C, and it may be sterilised using any method. FDA compliance is stated.Geometry and Final Particle SizeThe gap between the rotor and stator is 0.5 mm wide, and the peripheral speed is a maximum of 28.8 m/s. The final fineness is 5 to 20 µm for suspensions and 1 to 10 µm for emulsions. The immersion depth ranges from 80 to 450 mm, and the installation length is 510 mm. The tool measures 65 x 550 x 65 mm and weighs 4.45 kg; by comparison, the S 50 KG - HH - G 45 G weighs 0.552 kg.Siblings in the S 65 seriesThe S 65 KG - HH - G 65 M has the same design, processes 2 to 40 l and specifies 20 to 50 µm (suspensions) and 5 to 15 µm (emulsions). The S 65 KG - HH - G 65 G has a 53 mm rotor and processes 2 to 50 l. The S 65 KD - G 65 F is available with a PTFE seal and FFKM O-ring instead of a mechanical seal, and with a vacuum down to 100 mbar.Typical applicationsDispersing and emulsifying in batches of 2 to 30 lOperations under vacuum down to 1 mbarProcesses at pressures up to 6 barBatches involving solventsApplications where FDA compliance is requiredTechnical detailsWorking range (H2O)2 to 30 lStator diameter65 mmRotor diameter58 mmStator/rotor gap width0.5 mmMax. circumferential speed28.8 m/sImmersion depth80 to 450 mmInstallation length510 mmBearings and sealsBall bearing, mechanical seal (carbide/carbide)Materials in contact with the productFFPM, WC / AISI 316LpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilityAll methodsVacuum1 mbarMax. pressure6 barFinal fineness of suspensions5 to 20 µmFinal fineness of emulsions1 to 10 µmFDA complianceYesDimensions (W x H x D)65 x 550 x 65 mmWeight4.45 kgScope of delivery1 x IKA S 65 KG - HH - G 65 F dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Individual requirements and procurement serviceLT Laborhandel can source the T 65 digital drive and other tools on request. The procurement service assists in selecting the appropriate geometry.

The S 65 KD, G 65 G (0010000641) is suitable for batches ranging from 2 to 50 l. The stator and rotor measure 65 and 53 mm respectively, with a gap of 0.5 mm. IKA specifies the T 65 digital as the drive.Ball bearing with PTFE sealThe shaft runs in a ball bearing with a PTFE seal and an FFKM O-ring; the materials in contact with the product are FFPM, PTFE and AISI 316L. The unit is suitable for solvents; the pH range is 2 to 13. A vacuum of up to 100 mbar is permitted, and the maximum operating temperature is 170 °C. Sterilisation is carried out using a wet chemical method.Speed, fineness and dimensionsAt 9,500 rpm, the rotor circumference reaches 26.4 m/s. The final fineness ranges from 25 to 75 µm for suspensions and from 5 to 25 µm for emulsions. The immersion depth is 90 to 450 mm, the installation length is 520 mm, and batch sizes of 2,000 to 50,000 ml are recommended. The tool weighs 4.39 kg.Typical applicationsDispersing and emulsifying 2 to 50 lsuspensions with final particle sizes of 25 to 75 µmEmulsions with final particle sizes of 5 to 25 µmOperations under vacuum down to 100 mbarProcesses involving solventsTechnical detailsProcessable volume (H2O)2 to 50 lStator diameter65 mmRotor diameter53 mmStator/rotor gap width0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed26.4 m/sPenetration depth90 to 450 mmInstallation length520 mmBearing and sealBall bearing, PTFE seal, FFKM O-ringMaterials in contact with the productFFPM, PTFE, AISI 316LpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilitywet chemicalVacuum100 mbarFinal particle size of suspensions25 to 75 µmFinal particle size of emulsions5 to 25 µmWeight4.39 kgScope of delivery1 x IKA S 65 KD - G 65 G dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Variants with a 53 mm rotorTwo further tools have the same geometry (65 mm stator, 53 mm rotor, 0.5 mm gap): the S 65 C - G 65 G with AISI 316L and ceramic, which is not designed for vacuum use, and the S 65 KG - HH - G 65 G with a mechanical seal, capable of operating under vacuum down to 1 mbar and at pressures up to 6 bar. The S 65 KD - G 65 F operates with a 58 mm rotor and a particle size range of 5 to 20 µm for suspensions, but is limited to a capacity of 30 l. The larger rotor of the S 65 KD - G 65 M (58 mm, 28.8 m/s) handles 2 to 40 l and specifies 20 to 50 µm for suspensions.Individual requirements and procurement serviceA second unit, the T 65 digital drive, or assistance with selection: LT Laborhandel supplies equipment and provides advice via its procurement service.

The S 65 KD - G 65 M (0010000642) can process up to 40 l of water on a T 65 digital. There is a gap of 0.5 mm between the 65 mm stator and the 58 mm rotor; at 9,500 rpm, the rotor circumference reaches 28.8 m/s.Seals and materialsThe shaft runs in a ball bearing with a PTFE seal and an FFKM O-ring. Materials in contact with the product are FFPM, PTFE and AISI 316L. Solvents are permitted; the pH range is from 2 to 13. Under vacuum, the tool may be used down to 100 mbar; the maximum operating temperature is 170 °C. Sterilisation is carried out using a wet chemical process.Fineness and dimensionsThe final fineness ranges from 20 to 50 µm for suspensions and 5 to 15 µm for emulsions. The immersion depth is 80 to 450 mm, and the installation length is 520 mm. Batches of 2,000 to 40,000 ml are recommended. The tool weighs 4.21 kg.Typical applicationsDispersing and emulsifying 2 to 40 lemulsions with final particle sizes of 5 to 15 µmSuspensions with final particle sizes of 20 to 50 µmOperations under vacuum down to 100 mbarProcesses involving solventsTechnical detailsProcessable volume (H2O)2 to 40 lStator diameter65 mmRotor diameter58 mmStator/rotor gap width0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed28.8 m/sPenetration depth80 to 450 mmInstallation length520 mmBearing and sealBall bearing, PTFE seal, FFKM O-ringMaterials in contact with the productFFPM, PTFE, AISI 316LpH range2 to 13Suitable for solventsYesMax. operating temperature170 °CSterilisabilitywet chemicalVacuum100 mbarFinal particle size of suspensions20 to 50 µmFinal particle size of emulsions5 to 15 µmWeight4.21 kgScope of delivery1 x IKA S 65 KD - G 65 M dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Same geometry, different sealThe S 65 KG - HH - G 65 M has the same geometry (65 mm stator, 58 mm rotor, 0.5 mm gap) with a mechanical seal, which allows a vacuum down to 1 mbar and has an installation length of 510 mm. The S 65 C - G 65 M uses ceramic instead of PTFE and also operates with volumes of 2 to 40 l, but is not designed for vacuum. The S 65 KD - G 65 F is available for batches of up to 30 l with particle sizes of 5 to 20 µm in suspensions. The S 65 KD - G 65 G operates with a 53 mm rotor and handles batches of up to 50 l.Individual requirements and procurement serviceLT Laborhandel can supply the T 65 digital drive and other accessories on request. Through our procurement service, we will work with you to determine which geometry is best suited to your batch.

With an installation length of 520 mm and a weight of 4.24 kg, the S 65 KD - G 65 F (0010000643) is one of the larger tools for the T 65 digital. It processes 2 to 30 l with a 65 mm stator and a 58 mm rotor. The shaft runs in a ball bearing with a PTFE seal and an FFKM O-ring.Bearings, materials and limitsMaterials in contact with the product are FFPM, PTFE and AISI 316L. The pH range is from 2 to 13. Under vacuum, the tool may be used down to 100 mbar; the maximum operating temperature is 170 °C. Sterilisation is carried out using a wet chemical method.Geometry and precisionThe gap between the rotor and stator is 0.5 mm wide. At the maximum permissible speed of 9,500 rpm, the rotor peripheral speed reaches 28.8 m/s. The final particle size is 5 to 20 µm for suspensions and 1 to 10 µm for emulsions. The immersion depth is 80 to 450 mm; batch sizes of 2,000 to 30,000 ml are recommended.Mechanical seal as an alternativeThe S 65 KG - HH - G 65 F has the same operating range and the same rotor, but features a carbide mechanical seal. It operates at pressures ranging from 1 mbar to 6 bar and has an installation length of 510 mm.Larger capacitiesFor volumes up to 50 l, the S 65 C - G 65 G with AISI 316L and ceramic components and the S 65 KG - HH - G 65 G with a mechanical seal are suitable. Both have a 53 mm rotor and are specified for suspensions ranging from 25 to 75 µm.Typical applicationsDispersing and emulsifying in batches of 2 to 30 lOperation under vacuum down to 100 mbarSuspensions with final particle sizes of 5 to 20 µmEmulsions with final particle sizes of 1 to 10 µmProcesses with operating temperatures up to 170 °CTechnical detailsWorking range (H2O)2 to 30 lRecommended operating range2,000 to 30,000 mlStator diameter65 mmRotor diameter58 mmStator/rotor gap width0.5 mmMax. permissible speed9,500 rpmMaximum circumferential speed28.8 m/sPenetration depth80 to 450 mmInstallation length520 mmBearing and sealBall bearing with PTFE seal and FFKM O-ringMaterials in contact with the productFFPM, PTFE, AISI 316LpH range2 to 13Max. operating temperature170 °CSterilisabilitywet chemicalVacuum100 mbarFinal particle size of suspensions5 to 20 µmFinal particle size of emulsions1 to 10 µmWeight4.24 kgScope of delivery1 x IKA S 65 KD - G 65 F dispersing tool (single tool)The T 65 digital drive is not included in the Scope of delivery.Individual requirements and procurement serviceLT Laborhandel can source the T 65 digital drive and other tools on request. The procurement service will put together the right combination for your application.