Skip to main content Skip to search Skip to main navigation

Memmert incubator IN110m, 108 l, +20 to +80 °C, SingleDISPLAY

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "Memmert incubator IN110m, 108 l, +20 to +80 °C, SingleDISPLAY"

With 108 litres internal volume, the Memmert incubator IN110m lies between the IN75m and the IN160m. It is a Class I medical device under Regulation (EU) 2017/745, and its intended purpose is the warming and keeping warm of fango, silicate and APS packs in physiotherapy. Two electropolished stainless steel grid shelves are included as standard, up to five shelves are possible, and the total load goes up to 175 kg.

Pt100 sensor, PID controller and time control

The temperature is measured by a Pt100 sensor of DIN class A using 4-wire technology, and the setting accuracy is 0.1 °C. The control loop is handled by the ControlCOCKPIT SingleDISPLAY: an adaptive, multifunctional PID microprocessor with a high-resolution TFT colour graphic display. The digital countdown timer covers a range from 1 minute to 99 days. Thanks to the SetpointWAIT function, the process time only starts to run once the setpoint temperature has been reached, and three temperature values can be freely calibrated.

Ventilation and temperature monitoring

Natural ventilation admixes preheated fresh air via an electronically adjustable exhaust air flap, and an equally electronically controllable throttle valve sits at the exhaust air port. Around 20 °C above the maximum cabinet temperature, a mechanical temperature limiter of protection class 1 according to DIN 12880 switches the heating off, supplemented by an adjustable electronic temperature monitoring system. A self-diagnosis system supports fault finding.

Logging

After a power failure, the program sequence remains stored. Via an Ethernet interface, the data logger can be read out, managed and organised with the time-limited trial version of AtmoCONTROL, and a USB stick with the AtmoCONTROL software is available as an accessory.

Interior, door and connection

The interior is made of easy-care, deep-drawn ribbed stainless steel and is heated on all four sides, and the housing consists of textured stainless steel with a fully galvanised sheet steel rear panel. The fully insulated stainless steel door closes via a 2-point locking system with compression door lock, and behind it there is an inner glass door. Internally, the IN110m measures 560 x 480 x 400 mm, externally 745 x 864 x 584 mm plus 56 mm door handle, and it weighs around 76 kg net. The mains connection is 230 V with approx. 1,400 W or 115 V with approx. 900 W, each 50/60 Hz.

Distinction from the IN110 and IN110mplus

Without a medical intended purpose, the Memmert incubator IN110 is available in the same size. The IN110mplus also holds 108 litres, but shows its values via a ControlCOCKPIT TwinDISPLAY instead of SingleDISPLAY and serves a different intended purpose: warming irrigation and infusion solutions and contrast media.

Selection guide: which size fits

For a smaller space requirement, the IN75m with 74 litres offers six instead of five shelves, but only 120 instead of 175 kg total load. Those who need more volume will find it with the IN160m: 161 litres, eight shelves, 210 kg total load.

Typical applications

As a Class I medical device, the IN110m is intended exclusively for the physiotherapeutic applications named in the intended purpose.

  • Warming of fango packs for physiotherapeutic use
  • Warming and keeping warm of silicate packs
  • Warming and keeping warm of APS packs

Technical details

Setting temperature range+20 to +80 °C
Working temperature rangemin. 5 °C above room temperature to +80 °C
Temperature setting accuracy0.1 °C
Temperature sensor1x Pt100, DIN class A, 4-wire measurement
Internal volume108 l
Internal dimensions (W x H x D)560 x 480 x 400 mm
External dimensions of housing (W x H x D)745 x 864 x 584 mm (plus 56 mm door handle)
Net weightapprox. 76 kg
Connection230 V, 50/60 Hz, approx. 1,400 W; 115 V, 50/60 Hz, approx. 900 W
Shelves in scope of delivery2
Maximum shelves5
Max. load of unit175 kg
Max. load per shelf20 kg
ControlControlCOCKPIT SingleDISPLAY, PID microprocessor controller, TFT colour graphic display
Medical device classificationClass I under Regulation (EU) 2017/745
Intended purposeWarming/keeping warm of fango, silicate and APS packs in physiotherapy
Permissible ambient temperature+5 °C to +40 °C
Permissible humiditymax. 80 % rh, non-condensing
MarkingsCE, VDE, UL

Other sizes in the series

Within the IN-m series, the IN110m covers one of eight sizes, the series ranges from 32 to 749 litres, and each version has SingleDISPLAY and the same setting temperature range of +20 to +80 °C.

ModelInternal volumeSetting temperatureDisplay
IN30m32 l+20 to +80 °CSingleDISPLAY
IN55m53 l+20 to +80 °CSingleDISPLAY
IN75m74 l+20 to +80 °CSingleDISPLAY
IN110m (this page)108 l+20 to +80 °CSingleDISPLAY
IN160m161 l+20 to +80 °CSingleDISPLAY
IN260m256 l+20 to +80 °CSingleDISPLAY
IN450m449 l+20 to +80 °CSingleDISPLAY
IN750m749 l+20 to +80 °CSingleDISPLAY

Scope of delivery

  • 1x Memmert incubator IN110m
  • Factory calibration certificate (calibration at +37 °C)
  • 2x stainless steel grid shelf, electropolished

Regulatory information

The device is electrical equipment within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer Memmert GmbH + Co. KG is DE 66812464. Notes on returning old appliances can be found on our page Environment and disposal. The IN110m is also classified as a Class I medical device under Regulation (EU) 2017/745, with the intended purpose of warming and keeping warm of fango, silicate and APS packs in physiotherapy.

Installation in a wall opening

For fixed installation in a wall opening, Memmert offers a flush-fit unit. It covers the gap between the unit and the wall opening with stainless steel and is available with air slots (B29734) or without air slots (B29735). According to Memmert, the installation situation must be clarified technically beforehand. The flush-fit unit is therefore available on request through our procurement service.

Individual requirements and procurement service

For the IN110m, Memmert offers options, accessories and services, and options are specified at the factory with the order. We are available for questions about equipment, accessories or spare parts for the IN110m. As factory options, Memmert also offers DAkkS calibration according to DKD-R 5-7, IQ/OQ documents and IQ/OQ qualification. We order these with the device on request.

Volume: 108 l
Skip product gallery

Matching accessories

Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert stainless steel grid E20165 for sizes 105, 110, 150 and 160
Manufacturer number: E20165

The E20165 stainless steel grid is an electropolished shelf for 43 Memmert models in sizes 105, 110, 150 and 160. Each grid is a shelf level for the items loaded into the interior. If you need more shelf levels than are fitted as standard, you can add grids up to the maximum number in the table. The size corresponds to the number in the unit name, for example IF110 or UF110.For sizes 110 and 160, 2 grids are fitted as standard, and the interior holds up to 5 grids (size 110) or 8 grids (size 160). The HCP105 and HCP150 humidity chambers have 2 perforated shelves as standard; the maximum number there is 6 (HCP105) and 10 (HCP150). According to Memmert, the load per shelf is 20 kg, and 15 kg for the HCP105 and HCP150. The image is for illustration only. It is a Memmert drawing showing grids of different sizes.Typical applicationsTypical uses in the compatible units:Drying laboratory glassware and medium-sized sample series in routine operation, for example in the UF110Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material specimens and material samples, for example in the UF160Environmental tests and environmental simulations in the HCP105 and HCP150 humidity chambersSuitable forThe table shows for each model the number of grids included in the scope of delivery of the unit, the maximum possible number and the load per shelf.ModelGrids as standardMaximum number of gridsLoad per shelf (kg)Interior volume (l)IF110bw2520108IF1102520108IN110plus2520108UF1102520108UN110pa2520108UN160pa2820161IF1602820161IN1602820161IF110plus2520108IF160plus2820161IN160plus2820161UF110plus2520108UN1102520108UN110plus2520108UF1602820161UF160plus2820161UN1602820161UN160plus2820161IN1102520108IPP110eco2520108IPP110ecoplus2520108HPP110eco2520108HCP1052 (perforated shelf)615107HCP1502 (perforated shelf)1015156ICH1102520108ICP1102520108IN110m2520108IN110mplus2520108IF110m2520108IF110mplus2520108IN160m2820161IN160mplus2820161IF160m2820161IF160mplus2820161UN110m2520108UN110mplus2520108UF110m2520108UF110mplus2520108UN160m2820161UN160mplus2820161UF160m2820161UF160mplus2820161UF160TS2820161The permissible total load of the unit additionally limits the loading. Please refer to the information in the unit’s data sheet.Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmert20 kg, 15 kg for the HCP105 and HCP150Scope of delivery1 stainless steel grid, electropolished (E20165)Individual requirements & procurement serviceFor further grids, perforated trays or reinforced grids, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €98.04
memmert rohrverlaengerung gerade
Memmert straight slip-on pipe extension B29718 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29718

The straight slip-on pipe extension B29718 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The angled version is also available (B29719). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorTempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Drying and tempering of large, heavy components in industrial manufacturing, for example in the UF1060Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 straight slip-on pipe extensionIndividual requirements & procurement serviceFor the angled version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €41.28
memmert rohrverlaengerung gewinkelt
Memmert angled slip-on pipe extension B29719 for sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060
Manufacturer number: B29719

The angled slip-on pipe extension B29719 discharges the exhaust air and can be used to connect a hose if required. The pipe measures 60.3 mm on the outside and 57 mm on the inside.It is intended for Memmert U and Um universal ovens and I and Im incubators in sizes 30, 55, 75, 110, 160, 260, 450, 750 and 1060. The straight version is also available (B29718). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Parallel drying of several sample batches in a confined space, for example in the UN75Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material samples in series, for example in the UN260Testing and curing of larger components in quality assurance, for example in the UF750Suitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN450plus450449UF450plus450449UF450450449UN450450449UF750plus750749UF750750749UN750750749UN750plus750749UF106010601,060IF30plus3032IN30plus3032IF303032UF1060plus10601,060IN303032IF160160161IN450plus450449IN450450449IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF750plus750749IF110plus110108IN55plus5553IF450plus450449IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IN110110108IN757574IF757574IN750750749IF750750749IF450450449IN750plus750749IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256IN450m450449IN450mplus450449IF450m450449IF450mplus450449IN750m750749IN750mplus750749IF750m750749IF750mplus750749UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UN450m450449UN450mplus450449UF450m450449UF450mplus450449UN750m750749UN750mplus750749UF750m750749UF750mplus750749UF1060m10601,060UF1060mplus10601,060Technical detailsPipe, outside60.3 mmPipe, inside57 mmScope of delivery1 angled slip-on pipe extensionIndividual requirements & procurement serviceFor the straight version, for further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €108.36
Memmert Edelstahl-Gitterrost, Zeichnung verschiedener Größen
Memmert reinforced stainless steel grid E29767 for sizes 110 and 160
Manufacturer number: E29767

The reinforced stainless steel grid E29767 is available for Memmert units in the U, Um, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 110 and 160. It is electropolished and, according to Memmert, can bear up to 60 kg; for the standard grids in these sizes it is 20 kg per shelf. The grid is a shelf level in the interior. The size corresponds to the number in the unit name, for example IF110 or UF110.Please note the maximum load per unit, as it limits the total load of all shelves. The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Tempering, ageing and baking of material samples in industrial quality assurance, for example in the UN110Material tests in industrial manufacturing, for example in the UF160Suitable forModelSizeInterior volume (l)IF110110108IN110plus110108UF110110108IF160160161IN160160161IF110plus110108IF160plus160161IN160plus160161UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161IN110110108IPP110eco110108IPP110ecoplus110108HPP110eco110108ICH110110108ICP110110108IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161Technical detailsMaterialStainless steelSurfaceelectropolishedLoad per shelf according to Memmertup to 60 kgScope of delivery1 reinforced stainless steel grid, electropolishedIndividual requirements & procurement serviceFor standard grids, perforated trays and drip trays of the same size, and for questions about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €257.14
Memmert levelling feet B29768, set of 4, for sizes 30, 55, 75, 110, 160 and 260
Manufacturer number: B29768

The B29768 set of levelling feet contains 4 pieces. With levelling feet, the unit can be aligned horizontally.The set is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco and HPPeco series in sizes 30, 55, 75, 110, 160 and 260. The table of compatible models shows which series is available in which size. The size corresponds to the number in the unit name, for example UF30 or UN30.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorEmbedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenParallel stability studies of several active substance batches according to ICH Q1A, for example in the HPP260ecoSuitable forModelSizeInterior volume (l)UF303032IF110110108UN260plus260256UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN260260256UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574UN160pa160161IF30plus3032IN30plus3032IF303032IN303032IF160160161IN160160161IF260plus260256IN260plus260256IF260260256IF55plus5553IN260260256IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574IF160plus160161IN160plus160161UN55pa5553UF110plus110108UN110110108UN110plus110108UF160160161UF160plus160161UN160160161UN160plus160161UF260260256UF260plus260256IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032IPP260eco260256IPP260ecoPlus260256HPP110eco110108HPP260eco260256IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108IN160m160161IN160mplus160161IF160m160161IF160mplus160161IN260m260256IN260mplus260256IF260m260256IF260mplus260256UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108UN160m160161UN160mplus160161UF160m160161UF160mplus160161UN260m260256UN260mplus260256UF260m260256UF260mplus260256UF160TS160161UF260TS260256Scope of delivery1 set of levelling feet (4 pieces)Individual requirements & procurement serviceFor base frames, further accessories and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €46.44
memmert untergestell fahrbar
Memmert mobile base frame B29750, height 560 mm, for sizes 110 and 160
Manufacturer number: B29750

The mobile base frame B29750 is 560 mm high.It is intended for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco and IFbw series in sizes 110 and 160. The levelling version with a height of 500 mm is also available (B29749), as is a flat base frame with a height of 130 mm (B33661). The table of compatible models shows which series is available in which size. The image is for illustration only. The size corresponds to the number in the unit name, for example IF110 or UF110.Typical applicationsUnits of sizes 110 and 160 are placed on the base frame. Typical uses of these units:Tempering, ageing and baking of material specimens and material samples, for example in the UF160Incubating several sample series at the same time in research and medicine, for example in the IF110Vibration-free drying of dust- or air-sensitive materials in several batches, for example in the UN110Cooled incubation of larger sample quantities or several parallel test series below room temperature, for example in the IPP110ecoSuitable forModelSizeInterior volume (l)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 detailsHeight560 mmScope of delivery1 mobile base frame, height 560 mmIndividual requirements & procurement serviceFor the flat and the levelling version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €497.08
Memmert levelling base frame B33661, height 130 mm, for sizes 110 and 160
Manufacturer number: B33661

The levelling base frame B33661, with a height of 130 mm, is the flat version for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco and IFbw series in sizes 110 and 160. The size corresponds to the number in the unit name, for example IF110 or UF110.The base frame B29749 with a height of 500 mm is also available for these sizes. The table of compatible models shows which series is available in which size.Typical applicationsUnits of sizes 110 and 160 are placed on the base frame. Typical uses of these units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Tempering larger batches in the pharmaceutical industry, for example in the IF160Production of microscopic specimens in the laboratory, for example in the UN160pa paraffin ovenMaterials testing in industrial quality assurance, for example in the HPP110ecoSuitable forModelSizeInterior volume (l)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 detailsHeight130 mmScope of delivery1 levelling base frame, height 130 mmIndividual requirements & procurement serviceFor the taller version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €273.48
Memmert stacking kit B29744 for sizes 30, 50, 55, 75, 105 and 110
Manufacturer number: B29744

The B29744 stacking kit consists of 4 pieces and is intended for stacking units of the same size. It is intended for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco, HCP and IFbw series in sizes 30, 50, 55, 75, 105 and 110. The size corresponds to the number in the unit name, for example UF30 or UN30.Separate stacking kits are also available for HCP150, HCP240 and for ICO50, 180 and 240 (B42114, B48129, B68362 and B64732). The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying small sample series in laboratory operation, for example in the UF30Incubating several parallel series of culture media in routine microbiology, for example in the IN55 incubatorIncubating several sample series at the same time in research and medicine, for example in the IF110Environmental tests and environmental simulations in the HCP105 humidity chamberSuitable forModelSizeInterior volume (l)IF110bw110108UF303032IF110110108UN303032UF30plus3032UN30plus3032UF555553UF55plus5553UN555553UN55plus5553UF757574UF75plus7574UN75plus7574IN110plus110108UN757574UF110110108UN110pa110108UN75pa7574IF30plus3032IN30plus3032IF303032IN303032IF55plus5553IF110plus110108UN30pa3032IN55plus5553IF555553IN555553IN75plus7574IF75plus7574UN55pa5553UF110plus110108UN110110108UN110plus110108IPP555553IN110110108IN757574IF757574IPP55plus5553IPP110eco110108IPP303032IPP110ecoplus110108IPP30plus3032HPP110eco110108HCP505056HCP105105107IN30m3032IN30mplus3032IF30m3032IF30mplus3032IN55m5553IN55mplus5553IF55m5553IF55mplus5553IN75m7574IN75mplus7574IF75m7574IF75mplus7574IN110m110108IN110mplus110108IF110m110108IF110mplus110108UN30m3032UN30mplus3032UF30m3032UF30mplus3032UN55m5553UN55mplus5553UF55m5553UF55mplus5553UN75m7574UN75mplus7574UF75m7574UF75mplus7574UN110m110108UN110mplus110108UF110m110108UF110mplus110108Scope of delivery1 stacking kit (4 pieces)Individual requirements & procurement serviceFor the stacking kits for HCP humidity chambers and ICO CO₂ incubators, for base frames and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €61.92
Memmert Wandkonsole
Memmert wall bracket B29758 for size 110
Manufacturer number: B29758

The wall bracket B29758 is intended for wall mounting of Memmert units in the I, IFbw, Im, U, UNpa and Um series in size 110. The table of compatible models shows which series is available in this size. The image is a Memmert drawing and is for illustration only. The size corresponds to the number in the unit name, for example IF110 or IN110.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Incubating several sample series at the same time in research and medicine, for example in the IF110Embedding and heating of larger quantities of paraffin or wax, for example in the UN110paSuitable forModelSizeInterior volume (l)IF110110108IN110110108IF110plus110108IN110plus110108IF110bw110108IF110m110108IN110m110108IF110mplus110108IN110mplus110108UF110110108UN110110108UF110plus110108UN110plus110108UN110pa110108UF110m110108UN110m110108UF110mplus110108UN110mplus110108Scope of delivery1 wall bracket for wall mountingIndividual requirements & procurement serviceFor questions about wall mounting and about compatibility with units not listed in the table, our procurement service accepts enquiries.

Manufacturer's RRP: €302.72
memmert einschiebe abtropfschale
Memmert stainless steel slide-in drip tray B02073 for sizes 110 and 160
Manufacturer number: B02073

B02073 is a stainless steel slide-in drip tray with a 15 mm rim for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 110 and 160. It collects dripping liquid. According to Memmert, the maximum load is 3 kg per slide-in drip tray. The size corresponds to the number in the unit name, for example IF110 or UF110.Memmert points out that it can impair the spatial temperature distribution. The table of compatible models shows which series is available in which size. The base drip tray for the same unit size is also available (B04359). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Drying laboratory glassware and sample vessels in routine operation, for example in the UF160Embedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenSuitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelRim15 mmMaximum load according to Memmert3 kgScope of delivery1 stainless steel slide-in drip tray, 15 mm rimIndividual requirements & procurement serviceFor the base drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €117.82
memmert boden abtropfschale
Memmert stainless steel base drip tray B04359 for sizes 110 and 160
Manufacturer number: B04359

The B04359 base drip tray is made of stainless steel and has a 15 mm rim. It is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco, ICP, ICH and HPPeco series in sizes 110 and 160 and collects dripping liquid. According to Memmert, the maximum load per base drip tray for these sizes is 3 kg. The size corresponds to the number in the unit name, for example IF110 or UF110.In addition, according to Memmert, it can impair the spatial temperature distribution. The table of compatible models shows which series is available in which size. The slide-in drip tray for the same unit size is also available (B02073). The image is for illustration only.Typical applicationsTypical uses in the compatible units:Drying larger quantities of laboratory glassware and sample containers, for example in the UN110Drying laboratory glassware and sample vessels in routine operation, for example in the UF160Embedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenSuitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelRim15 mmMaximum load according to Memmert3 kgScope of delivery1 stainless steel base drip tray, 15 mm rimIndividual requirements & procurement serviceFor the slide-in drip tray, for grids and perforated trays of the same size, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €171.14
memmert untergestell nivellierbar
Memmert levelling base frame B29749, height 500 mm, for sizes 110 and 160
Manufacturer number: B29749

B29749 is a levelling base frame with a height of 500 mm for Memmert units in the U, Um, UNpa, I, Im, IPPeco, HPPeco and IFbw series in sizes 110 and 160. The size corresponds to the number in the unit name, for example IF110 or UF110.A flat base frame with a height of 130 mm is also available (B33661). The mobile version with a height of 560 mm is also available (B29750). The table of compatible models shows which series is available in which size. The image is for illustration only.Typical applicationsUnits of sizes 110 and 160 are placed on the base frame. Typical uses of these units:Drying laboratory glassware and medium-sized sample series in routine operation, for example in the UF110Parallel incubation of several sample series in research and medicine, for example in the IF160Embedding and heating larger quantities of paraffin or wax, for example in the UN110pa paraffin ovenStability studies of individual active substance batches according to ICH Q1A in pharmaceutical quality assurance, for example in the HPP110ecoSuitable forModelSizeInterior volume (l)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 detailsHeight500 mmScope of delivery1 levelling base frame, height 500 mmIndividual requirements & procurement serviceFor the flat and the mobile version, for base frames for other unit sizes, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €350.88
Stainless steel perforated shelf, illustration
Memmert stainless steel perforated tray B68508 for sizes 110 and 160
Manufacturer number: B68508

This stainless steel perforated tray (B68508) is intended for Memmert units in the U, Um, UF TS, UNpa, I, Im, IPPeco, ICP, ICH, HPPeco and IFbw series in sizes 110 and 160. It is a shelf and therefore one shelf level in the interior. The size corresponds to the number in the unit name, for example IF110 or UF110. The image is for illustration only.According to Memmert, a maximum of 20 kg is permitted per shelf. If you want to load several shelves, also check the maximum load per unit in the data sheet. The table of compatible models shows which series is available in which size.Typical applicationsTypical uses in the compatible units:Drying laboratory glassware and medium-sized sample series in routine operation, for example in the UF110Parallel incubation of several sample series in research and medicine, for example in the IF160Tempering, ageing and baking of material specimens and material samples, for example in the UF160Suitable forModelSizeInterior volume (l)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 detailsMaterialStainless steelLoad per shelf according to Memmert20 kgScope of delivery1 stainless steel perforated trayIndividual requirements & procurement serviceFor grids, further perforated trays and drip trays, and for questions about compatibility with older Memmert units, our procurement service accepts enquiries.

Manufacturer's RRP: €163.40